Hunter Fan 90056 Owner's manual

Brand
Hunter Fan
Model
90056
Type
Owner's manual
41719-01 01/28/2008
1
Installation Guide
90055/90056/90057 Low Profile
™
Bath Ventilator with Light
READ and SAVE THESE INSTRUCTIONS
ENGLISH
See page 2
ESPAñOL
Vea la página 23
030_41719_EngS_1.28.08_Arial.indd 1 1/28/08 11:57:46 AM
41719-01 01/28/2008
2
DISCONNECT ELECTRIC
POWER SUPPLY
AND LOCK OUT
SERVICE PANEL BEFORE
SERVICING UNIT
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
1. For general ventilating use only. Do not use to exhaust hazard-
ous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy/unbalanced impellers,
keep drywall spray, construction dust, etc. off power unit.
3. DO NOT install this product in a wall. This product is designed
for installation in ceilings up to a 12/12 pitch (45 degrees).
Ductwork must point upward.
4. Pleasereadspecicationlabelonproductforfurtherinformation
and requirements.
PREVENTATIVE MAINTENANCE
A clean fan provides better service. Disconnect the power supply and
clean the fan as listed below.
TO CLEAN GRILLE: Use a mild detergent, such as dishwashing
liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads
or scouring powders.
TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle.
To remove motor plate, find the single tab on the motor plate (located
next to the receptacle). Push up rear motor plate tab while pushing
out on the side of the housing or insert a screwdriver into the slot in
the housing (next to tab) and twist screwdriver. Gently vacuum fan,
motor and interior of housing.
METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED
IN WATER.
MAINTENANCE
The motor is permanently lubricated and never needs oiling. If the
motor bearings are making excessive or unusual noises, replace the
motor with the exact service motor. You should replace the impeller at
the same time.
CAUTION
WARNING
1. Use this unit only in a manner intended by the manufacturer.
If you have questions, contact the manufacturer.
2. Before servicing or cleaning the unit, switch power off at ser-
vice panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by quali-
edperson(s)inaccordancewithallapplicablecodesand
standards,includingre-ratedconstruction.
4. Sufcientairisneededforpropercombustionandexhausting
ofgassesthroughtheue(chimney)offuelburningequipment
to prevent backdrafting. Follow the heating equipment manufac-
turer’s guideline and safety standards,such as those published
by the National Fire Prevention Association (NFPA), and the
American Society for Heating, Refrigeration and Air-Conditioning
Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall(s) or ceiling, do not damage
electrical wiring or other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed over a tub or shower, it must be
marked as appropriate for the application and be connected to a
GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.
8. Never place a switch where it can be reached from a tub or
shower.
9. Installfanatleast5feet(1.52m)abovetheoor.
10. This unit must be grounded.
11. Unit must not be installed in a ceiling thermally insulated to a
value greater than R40.
Do Not Install Above
Or Inside This Area
Cooking
Equipment
Floor
45° 45°
COOKING AREA
030_41719_EngS_1.28.08_Arial.indd 2 1/28/08 11:57:46 AM
41719-01 01/28/2008
3
D
E
F
G
H
I
L
M
N
95044-01-000
95029-01-000
75191-01-000
03242-07-133
95491-02-000
74508-03-133
95511-01/02/03-000
J
77521-01
K
65219
75184-01-133
94997-01/02/03-000
O
7517-01/02/03-000
x4
*
*
*
NOTE:
Strain relief cable
connector must be
installed. Not Included.
A
B
C
Extra Screws
x2
I
3/8” Cable Connector
x2
1
2
E
I
Turn off the power source.
Tools Needed.
Estimated assembly time: 30 to 60 minutes
Before Installation
Check all the parts.
If damaged, call
1-888-830-1326
for replacements.
Included.
Loosen screws.
NOTE: Remove all packing materials before installation.
030_41719_EngS_1.28.08_Arial.indd 3 1/28/08 11:57:48 AM
41719-01 01/28/2008
4
5
4
7
G
8
F
H
E
3
6
Remove the motor/blower from the housing.
Remove the pre-loaded screw tip covers.
Remove the wiring cover screw.
Back out the pre-loaded screw tips until flush
with the side of the housing.
Remove the wiring cover.
Remove packing material.
030_41719_EngS_1.28.08_Arial.indd 4 1/28/08 11:57:51 AM
41719-01 01/28/2008
5
9
E
10
B
C
A11
E
5/8
1/2
5/8
1/2
A12
Pop out the first wiring access slug. Use second if needed. Insert the strain relief into the housing and
secure with the washer.
Position the correct depth mark at the bottom edge of the
joist based on the thickness of your sheetrock.
New Construction – attaching to joist
Choose Installation Option
For New Construction - attaching to joist go to step A11, page 5
For New Construction - suspended between joists go to step B11, page 8
For Existing Construction - accessible from above go to step C11, page 11
For Existing Construction - accessible only from below go to step D11, page15
Screw pre-loaded screws into joist or framing.
030_41719_EngS_1.28.08_Arial.indd 5 1/28/08 11:57:53 AM
41719-01 01/28/2008
6
A
3 Pin
2 Pin
Fan Motor
Light
Light
Green
Black
Black
White
Black
Black
White
White
Bare Copper
Ground
A14
Main Switch 1 (AC In)
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
A13
0
A16
Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may need
to be purchased.
A15
E
F
G
Install the wiring cover plate. Make sure all
wiring connections are inside the box or under
the wiring cover plate.
Connect wires as shown.
Pull wires through the strain relief.
030_41719_EngS_1.28.08_Arial.indd 6 1/28/08 11:57:55 AM
41719-01 01/28/2008
7
A19
I
A20
Connect wiring from the motor to the wiring cover plate.
0000
A17
0000
H
A18
ON
OFF
A21
A22
E1
Go to step
on page 17
to attach grille.
Reinstall the motor by inserting the tabs and pushing up into
position. Make sure the wires are not pinched
between the motor and the housing.
Secure the motor by tightening the 2 screws.
Turn on the power source.
Test the motor. If the motor does not run,
check the plug connection.
030_41719_EngS_1.28.08_Arial.indd 7 1/28/08 11:57:58 AM
41719-01 01/28/2008
8
B11
D
E
5/8
1/2
5/8
1/2
B12
1/8" Bit
B14
B16
E
B13
Slide the mounting rails into brackets.
Mark position of screws by using holes as a template.
Insert screws, leaving space between the screw
head and the joist. Screws are not provided.
New Construction – suspended between joists
Position the correct depth mark at the bottom edge of
the joist based on the thickness of your sheetrock.
Drill a hole in the center of each outline.
Attach the rails onto the screws.
030_41719_EngS_1.28.08_Arial.indd 8 1/28/08 11:58:01 AM
41719-01 01/28/2008
9
B17
B18
Connect wires as shown.
A
3 Pin
2 Pin
Fan Motor
Light
Light
Green
Black
Black
White
Black
Black
White
White
Bare Copper
Ground
B19
Main Switch 1 (AC In)
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
B21
Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may need
to be purchased.
Install the wiring cover plate. Make sure all wiring
connections are inside the box or under the
wiring cover plate.
F
G
B20
Tighten screws. Pull wires through the strain relief.
030_41719_EngS_1.28.08_Arial.indd 9 1/28/08 11:58:04 AM
41719-01 01/28/2008
10
B27
E1
Go to step
on page 17
to attach grille.
B22
H
Connect wiring from the motor to the wiring cover plate.
H
B23
Reinstall the motor by inserting the tabs and pushing up into
position. Make sure the wires are not pinched
between the motor and the housing.
B25
Turn on the power source.
ON
OFF
B26
Test the motor. If the motor does not run,
check the plug connection.
B24
I
Secure the motor by tightening the 2 screws.
030_41719_EngS_1.28.08_Arial.indd 10 1/28/08 11:58:07 AM
41719-01 01/28/2008
11
C12
D
E
EXISTING FAN
C11
NO EXISTING FAN
8”
8.5”
5/8
1/2
5/8
1/2
C13
C14
Existing Construction – accessible from above
OR
Cut out an opening for the housing. Slide the mounting rails into brackets.
Position the correct depth mark at the bottom edge of the
joist based on the thickness of your sheetrock.
Mark position of screws by using holes as a template.
Remove an existing fan and check to make sure the
opening is large enough to accommodate the new
motor housing (8”x 8.5”).
Use the motor housing as a template to mark position.
030_41719_EngS_1.28.08_Arial.indd 11 1/28/08 11:58:10 AM
41719-01 01/28/2008
12
C15
1/8" Bit
C16
C17
C18
C19
C20
Drill a hole in the center of each outline. Insert screws, leaving space between the screw head
and the joist. Screws are not provided.
Attach the rails onto the screws. Tighten screws.
Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may
need to be purchased.
Pull wires through the strain relief.
030_41719_EngS_1.28.08_Arial.indd 12 1/28/08 11:58:13 AM
41719-01 01/28/2008
13
C21
A
3 Pin
2 Pin
Fan Motor
Light
Light
Green
Black
Black
White
Black
Black
White
White
Bare Copper
Ground
C22
Main Switch 1 (AC In)
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
C24
H
G
F
C23
Tighten the strain relief screws.
Connect wires as shown.
Install the wiring cover plate. Make sure all wiring
connections are inside the box or under the
wiring cover plate.
Connect wiring from motor the motor
to the wiring cover plate.
030_41719_EngS_1.28.08_Arial.indd 13 1/28/08 11:58:15 AM
41719-01 01/28/2008
14
C25
H
C26
I
C27
ON
OFF
C28
C29
E1
Go to step
on page 17
to attach grille.
Secure the motor by tightening the 2 screws.
Turn on the power source.
Test the motor. If the motor does not run,
check the plug connection.
Reinstall the motor by inserting the tabs and pushing up into
position. Make sure the wires are not pinched
between the motor and the housing.
030_41719_EngS_1.28.08_Arial.indd 14 1/28/08 11:58:18 AM
41719-01 01/28/2008
15
EXISTING FAN
D11
E
D12
D13
2
1
D14
E
D15
Existing Construction – accessible only from below
Pull wires through strain relief.
Remove an existing fan and check to make sure the
opening is large enough to accommodate the new motor
housing (8”x 8.5”).
Move the housing into position above the ceiling.
Attach existing ducting to duct connector. Tape joints.
If ducting does not fit securely,
an adapter may need to be purchased.
Install the housing flush with the sheetrock and secure by
tightening the pre-loaded screws into the joist.
030_41719_EngS_1.28.08_Arial.indd 15 1/28/08 11:58:20 AM
41719-01 01/28/2008
16
H
D18
H
D19
D20
I
A
3 Pin
2 Pin
Fan Motor
Light
Light
Green
Black
Black
White
Black
Black
White
White
Bare Copper
Ground
D16
Main Switch 1 (AC In)
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
F
D17
G
Reinstall the motor by inserting the tabs and pushing up into
position. Make sure the wires are not pinched between the
motor and the housing.
Connect wiring from the motor to the wiring cover plate.
Secure the motor by tightening the 2 screws.
Connect wires as shown.
Install the wiring cover plate.
030_41719_EngS_1.28.08_Arial.indd 16 1/28/08 11:58:23 AM
41719-01 01/28/2008
17
ON
OFF
D22
D23
E1
Go to step
on page 17
to attach grille.
D21
E2
O
L
N
M
E1
Test the motor. If the motor does not run,
check the plug connection.
Turn on the power source.
Attaching the Grille
Remove the thumbscrews.
Remove glass dome.
030_41719_EngS_1.28.08_Arial.indd 17 1/28/08 11:58:25 AM
41719-01 01/28/2008
18
E4
K
E5
J
E6
L
E3
Remove the strain relief bracket screw.
Position the strain relief bracket under the motor as shown. Insert the strain relief bracket’s dog-leg tab so that
it hooks over the lip of the motor. Reinstall the
strain relief bracket screw.
Connect wiring harness.
E7
L
L
M
E8
Align posts A, B, C and D (stamped into motor housing)
with posts A, B, C and D (stamped into light fixture).
Slide light fixture over posts.
Attach thumbscrews.
WARNING: To reduce the risk of electrical shock,
all 4 thumbscrews MUST be properly installed.
030_41719_EngS_1.28.08_Arial.indd 18 1/28/08 11:58:29 AM
41719-01 01/28/2008
19
E9
E10
N
O
E11
Install 2 Max 60 Watt A15 bulbs (Not Included).
Screw glass dome into position.
Align glass dome and push up.
030_41719_EngS_1.28.08_Arial.indd 19 1/28/08 11:58:31 AM
41719-01 01/28/2008
20
Trouble Shooting
Problem: Fan does not come on.
Solution:
 •HunterFanBathVentilatorsareextremelyquiet.Toconrmthatthefanisrunning,placeyourhandneartheventstofeel
the air movement.
 •Turnpoweron,replacefuse,orresetbreaker.
 •Checkallplugconnectionstobesuretheyaresecure.
 •Checkthewiringtomakesureitmatchesthewiringdiagram.
Problem: Light does not come on.
Solution:
 •Replacethelightbulbwithanewbulb.
 •Turnpoweron,replacefuse,orresetbreaker.
 •Checkallplugconnectionstobesuretheyaresecure.
 •Checkthewiringtomakesureitmatchesthewiringdiagram.
Problem: Fan is noisy.
Solution:
 •Checkandtightenallfasteners.
 •Checktheglasstomakesureitissecure.
 •Checktheappertomakesureitmovesfreely.
If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at http://www.hunterfan.com.
030_41719_EngS_1.28.08_Arial.indd 20 1/28/08 11:58:31 AM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Hunter Fan 90056 Owner's manual

Brand
Hunter Fan
Model
90056
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents