HASE Cartago Operating Instructions Manual

Page is loading ...

R5_01/2015

Deutsch S. 4 - 14

Français P. 16 - 23

Italiano P. 24 - 31

English P. 32 - 39

Nederlands P. 40 - 47

Page is loading ...

14

14. Typenschild

43.12-376

15. DIBt Übereinstimmungszeichen

13/2015

1427

*Bedienungsanleitung beachten

Note the Instructions for use

Hase Kaminofenbau GmbH - Niederkircher Str. 14

54294 Trier/Germany

Prüfzeichen VKF-Nr.: 25197

CO-Emission (bei 13% 02): <1250mg/Nm

3

Staub-Emission (bei 13% 02): <40mg/Nm

3

Zeitbrandfeuerstelle für geschlossenen

Betrieb

Gerät ist für eine Mehrfachbelegung

des Schornsteins geeignet.*

Sicherheitsabstände zu brennbaren

Materialien: hinten 6 o. 3* cm / zur Seite

40 cm / vorne 90 cm

Intermittent burning heating appliance for

closed operation

Appliance suitable for multiple connection

to the chimney.*

Safety distances to combustible materials:

6 or 3* cm to the back / 40 cm to the sides

90 cm to the front

Heizleistung 7 kW Thermal output

Zulässige Brennstoffe Permitted fuel

CO-Emmision (bei 13% 02) CO emission (at 13% 02)

Scheitholz 0,04 Vol% Firewood

Mittlere Abgasstutzentemperatur 335 °C Mean temperature at waste gas outlet

 EnergieefzienzScheitholz 78 % Energyefciency,rewood

Raumheizer / Space heater EN13240:2001; 2001/A2:2004;2001/AC:2006;AC:2007

Typ / Type: CARTAGO (Typ FC

41x

und FC

51x

)

DIBT Zulassung / approval no.: Z-43.12-376 / Dop: Cartago-2013/10/01

Schweiz / Swiss

Geprüft nach: ART 15a-B-VG

Prüfberichtsnummer: FSPA-WA 2209-1-EN-A

Wärmeleistung:7,4kW

Brennstoffwärmeleistung:9,2kW

Österreich / Austria

Made in Germany

Page is loading ...

32

We hope your stove brings you:

the joy of fire, time for enjoyment,

and relaxing, cosy hours.

Your Hase team

33

1. General Information

This section contains important information on us-

ingthistechnicaldocumentation.Utmostcarewas

taken in preparing this document. Nevertheless,

suggestions for improvement and comments re-

garding any errors are always welcome.

1.1 Definition of Safety Notes

WARNING!

This symbol alerts you to a potentially

hazardous situation. Non-compliance with

this warning can cause severe injuries, or

even death.

CAUTION!

This symbol alerts you to a potentially

hazardous situation. Non-compliance can

cause damage to property or injuries to

persons.

NOTE!

Provides additional tips about using the

stove as well as useful information.

ENVIRONMENT!

Sections marked with this symbol provide

information about safe and environmen-

tally-friendly operation as well as envi-

ronmental laws and regulations.

Contents Page

1. General Information ................................... 33

  1.1 DenitionofSafetyNotes .............. 33

2. Control Elements ...................................... 34

3. Safety Distances ....................................... 35

4. Connection of Multiple Devices in .................

Direct Vent Operation ................................. 35

5. Fuel Load Sizes and Thermal Output .......... 36

6 . Initial Operation ......................................... 36

7. Lighting the Fire ......................................... 36

8. Adding Fuel / Heating at Nominal .............. 37

Thermal Output ......................................... 37

9. Heating at Low Thermal Output

(during Transitional Seasons) .................... 37

10. Emptying the Ash Drawer .......................... 38

11. Cleaning the ceramic glass panel ............... 38

12. Technical Data ........................................... 39

34

2. Control Elements

Fire box door handle

Air slider

Ash drawer

Maintenance and cleaning position of

the re box door

During maintenance and cleaning the furnace

door can be prevented from closing itself by

pushing the latch at the top of the furnace

door inwards. Once the necessary work is

completed, the furnace door is unlocked by

opening it fully.

Fire box door

35

3. Safety Distances

Within a radius of 90 cm in front of and 40 cm

around the stove,  ammable, combustible, or

heat-sensitive materials (e.g. furniture, wood or

plastic panelling, curtains, etc.) are not allowed to

belocatedintheheatradiatingareaoftherebox

window(g.1).

*Outside of the radiation area, it is necessary to

maintainadistanceof6cmbetweentheupperue

pipeconnectorandanyammablematerial,anda

distanceof3cmbetweenthebackuepipecon-

nectorandanyammablematerial(g.1).

WARNING!

Flammable ooring materials (e.g., wood,

laminate, carpeting,) must be protected

with a oorplate made of non-combustible

material (e.g., tiles, safety glass, slate, or

sheet steel).

The oorplate must protrude 50 cm over

the side of the rebox opening. It must

overhang the ground plot of the oven by

10 cm at the front and 17 cm at the back

(g. 2).

4. Connection of Multiple Devices in

Direct Vent Operation

When the Cartago is operated as a direct vent

model, more than one device can be connected to

the chimney under the following conditions:

CAUTION!

All connected replace stoves must be in

the same building unit or in the same ef-

fective area of the ventilation system.

The inlets for the combustion air ducts

are located in areas of equal pressure

(same pressure ratios), wind-induced

pressure uctuations have to be avoided.

The inlets for the combustion air ducts

are located in areas of equal pressure

(same pressure ratios), wind-induced

pressure uctuations have to be avoided.

Dimensions in cm

g. 2

g. 1

6/3*

40

90

oorplate

R

a

d

i

a

t

i

n

g

A

r

e

a

17

10

50

36

5. Fuel Load Sizes and Thermal Output

The thermal output depends on the amount of

fuelyouputinthestove.Whenaddingmorefuel,

please do not exceed the maximum fuel load size

of 2.2 kg. Exceeding the maximum fuel load size

leads to a danger of overheating, which can result

indamagetothestoveandtheriskofastovere.

NOTE!

To attain a thermal output of approx. 7kW,

burn wood logs that weigh 1.7 kg and are

no longer than 25 cm in length for about

45 min.

The Cartago is intended for intermittent operation,

please only apply one fuel layer at a time.

6 . Initial Operation

NOTE!

During shipment, condensation moisture

can accumulate in the stove’s interior,

which may possibly lead to the appear-

ance of condensation or water on the

stove or ue pipes. Please dry off these

damp areas immediately.

The surface of your stove was treated in a sand-

blasting machine before applying the colour coat-

ing. Despite careful and thorough inspection, there

may still be some residual material in the stove

body, which can fall out when your stove is being

installed.

NOTE!

To prevent any damage, please immedi-

ately vacuum up these small steel pellets

with a vacuum cleaner.

Thersttimeastoveisoperated,theheatdevelop-

ment causes the emission of volatile components

from the coating, sealing strips and lubricants, and

smoke and odours can occur.

At a higher combustion temperature, this one-time

process can take between 4 to 5 hours.

To achieve this higher combustion temperature,

please increase the fuel quantity recommended

in Section 8, „Adding Fuel/ Heating with Nominal

Thermal Output“, by approximately 50%.

CAUTION!

To prevent adverse effects on health, no-

body should stay in the room(s) during

this process unless absolutely necessary.

Make sure the room is well-ventilated and

open the windows and outside doors. If

needed, use a fan for faster air circula-

tion.

If the maximum temperature is not reached dur-

ingthe rstheatingoperation, youmay noticean

odour for a short period of time the next time the

stove is used as well.

7. Lighting the Fire

Thering upphase shouldbe asshort aspossi-

ble, since higher emissions can occur during this

phase.

The slider settings described in Table 1 are recom-

mendations that were determined under conform-

ance testing conditions, in compliance with the

relevant standard. Depending on the weather con-

ditions and the draught capability of your chimney,

accordingly adjust the slider positions for your Car-

tago to the local conditions.

NOTE!

When lighting and adding fuel to the fur-

nace, regulate the secondary air using the

air slider. The air slider can be put in a

heating position which speeds up the igni-

tion process. In the heating position, the

primary air supply is increased to speed

up the start phase. As soon as the fuel

is completely ignited, the heating phase

should be stopped (push in the air slider

until the red marker is no longer visible.).

NOTE!

The Cartago may only be operated when

the re box door is closed; the re box

door may only be opened to add fuel.

WARNING!

Never use spirits, petrol, or other amma-

ble uids to light the stove.

37

8. Adding Fuel / Heating at Nominal

Thermal Output

More fuel should be added to the re when the

ames from the previous burningoff phase have

just gone out.

Adding Fuel / Heating at Nominal Output

Procedure Position of

Control Elements

Adjust the combustion air. Set air slider on position 2.

Lay two logs, weighing

around 1.7 kg in total, in

the furnace with the front

end facing forward, so

that there is still a 2-3 cm

gap to the left and the

right between them and

the furnace wall. Only add

a single layer of fuel.

Tab. 2

CAUTION!

If the layer of embers is completely cov-

ered by very thick logs, the wood cannot

ignite properly and there is a possibility of

deagration.

9. Heating at Low Thermal Output

(during Transitional Seasons)

You can vary the thermal output of your Cartago by

adjustingthequantityoffuelused.

NOTE!

Do not attempt to slow down the com-

bustion by reducing the air supply. When

heating with wood, this can result in an

incomplete burning process and pose the

risk of an explosive like combustion of the

accumulated wood gases (deagration).

CAUTION!

The door handle can become hot dur-

ing operation. When adding more wood,

protect your hands with the oven gloves

included.

Lighting the Fire

Procedure Position of Control

Elements

Switch air slider to the

heating-up position.

Pull out the air slider out

completely across the

red mark.

Pile up any remaining ash

and unburned charcoal

into the centre of the

combustion chamber.

Place 4-6 small pieces of

wood with an approx. Ø

of 3-6 cm and max. 2 kg

in the middle of the burn-

ing chamber. Layer these

cross-wise on top of each

other. Place approx. 0.5

kg of wood shavings on

topasarelighter.

Light the kindling/ignition

material.

Stop the heating phase

as soon as the fuel is

completely ignited.

Push in the air slider

until the red marker is no

longer visible.

Tab. 1

38

10. Emptying the Ash Drawer

As a safety precaution, please make sure that you

onlydisposeofashesoncetheyarecold.Whilethe

ashcollectsduringthere,thelid(g.3/1)islo-

cated under the ash drawer

(g.3/2).

The ash drawer contains the mineral components

of the wood (approx. 1%) as combustion residues.

Remove both the ash drawer and the lid located

underneath it. Make sure the ash does not pile up

allthewaytothebottomoftherebox.Slidethe

lid onto the ash drawer so that it is closed; this

prevents ashes from ying around, which in turn

meansyourhomestaysclean(g.4).

Please ensure that, when inserting the ash drawer,

the ash drawer lid is positioned on the base of the

drawer with the side brackets facing down.

1

g. 3

2

1

g. 4

11. Cleaning the ceramic glass panel

Open the re box door and secure it against ac-

cidental closing (see point 2). To clean use the

included protective glove with an extra long shaft.

This protects you and your clothing from getting

dirty.

We recommend a proven and environmentally

friendly cleaning method:

Ball some up paper towels or newspaper, moisten

the ball, dip it into the cold wood ash, rub the panel

with it and then wipe the glass with a clean, dry

ball of paper.

NOTE!

Only use wood ash from split logs for this

cleaning process. Wood briquettes can

contain additives, which may scratch the

surface of the ceramic glass.

A common, retail glass detergent may also be used

forcleaning.Whencleaningthesealandsteelsur-

faces we recommend that you spray the glass de-

tergent on a cloth and not directly on the pane.

39

Dimensions in cm

12. Technical Data

The Cartago, certied in compliance with DIN-EN 13240, can only be oper-

atedwhen thereboxisclosed. Conforms withthe DIBt(Deutschen Institutfür

Bautechnik/German Institute for Building Technology) approval criteria for direct

ventreplacesfor solidfuels.Multiple connections to the chimney are possible,

see point 4. “Connection of Multiple Devices in Direct Vent Operation”.

VKF-No.: 25197; DIBt approval number: Z-43.12-376 / Typ FC41x und FC51x

The following data applies to the chimney characteristics in accordance with EN

13384-1 / 2

Combustion Values Wood

Nominal Thermal Output 7 kW

Efciency 78 %

Particulate <20 mg/m³

CO content at 13% O2 500 mg/m³

WasteGasMassFlowRate 7 g/s

WasteGasOutletTemp. 335 ˚C

Min. Supply Pressure at Nominal Thermal Output 12 Pa

Min.requiredcombustionairvolume 30 m³/h

Depending on the insulation of the building, the nominal thermal output of 7 kW

indicated on 25 bis 95 m² (subject to change)

Dimensions: Height Width Depth

Stove 132,5 cm 35,5 cm 53 cm

Fire box 65 cm 20 cm 27,5 cm

Weight 168 kg

Flue pipe diameter 15 cm

Pipe diameter of Hase ventilation system* 10 cm

*Forseparateairsupplyinlow-energyhousesandinsufcientcombustionair

supply in the room where the stove is installed.

Front view Side view

Top view

Inst. of Hase air system

below

20,5

Height for top installation: 130,5

35,5

Stove height: 132,5

53

Height for inst. of hase air system: 9

Height for rear installation: 120,5

18

10-16

Page is loading ...

HASE Cartago Operating Instructions Manual

HASE Cartago Operating Instructions Manual

in other languages

Related papers

Other documents