Flymo EasiCut 500CT Owner's manual

EASICUT

500CT

GB

Original Instructions

DE

Originalanleitung

FR

Instructions d’origine

NL

Oorspronkelijke instructies

NO

Originalinstrukser

FI

Alkuperäiset ohjeet

SE

Originalinstruktioner

DK

Originale instruktioner

ES

Instrucciones originales

PT

Instruções Originais

IT

Istruzioni originali

HU

Eredeti Utasítás

PL

Oryginalne Instrukcje

CZ

Originální pokyny

SK

Pôvodné pokyny

SI

Originalna navodila

HR

Originalne upute

LT

Pagrindinės instrukcijos

RU

 

EE

Algsed juhised

LV

Sākotnējās instrukcijas

RO

Instrucţiuni originale

GR

Αρχικές οδηγίες

TR

Orijinal Talimatlar

®

5052866-01 Easicut 500CT Euro.qxp:5052866-01 Easicut 500CT Euro.qxp 26/1/11 15:29 Page 1

GB

IMPORTANT INFORMATION

Read before use and retain for future

reference

DE

WICHTIGE INFORMATION

Bitte vor dem Benutzen des Gerätes

durchlesen und gut aufbewahren

FR

RENSEIGNEMENTS IMPORTANTS

A lire avant usage et à conserver pour

référence ultérieure

NL

BELANGRIJKE INFORMATIE

Leest u deze informatie voor het gebruik en

bewaar ze voor toekomstige raadpleging

NO

VIKTIG INFORMASJON

Les bruksanvisningen nøye før bruk og

oppbevar den for senere bruk

SE

VIKTIG INFORMATION

Läs anvisningarna före användningen och

spara dem för framtida behov

DK

VIGTIGE OPLYSNINGER

Du bør læse brugsanvisningen før brug og

gemme til senere henvisning

ES

INFORMACIÓN IMPORTANTE

Léase antes de utilizar y consérvela como

referencia en el futuro

PT

INFORMAÇÕES IMPORTANTES

Leia antes de utilizar e guarde para

consulta futura

IT

INFORMAZIONI IMPORTANTI

Leggere prima dell’uso e conservare per

ulteriore consultazione

TÄRKEÄÄ TIETOA

Lue tämä ennen käyttöä ja säilytä

myöhempää tarvetta varten

SK

SI

HU

PL

CZ

FI

FONTOS INFORMÁCIÓ

Használat előtt olvassa el, és tartsa meg

későbbi felhasználásra

HR

UWAGA Zapoznać się z treścią niniejszej

instrukcji przed użyciem i zachować ją do

dalszego użytkowania urządzenia

DŮLEŽITÁ INFORMACE

Než začnete stroj používat, přečtěte si pozorně

tento návod a uschovejte jej pro další použití v

budoucnu

DÔLEŽITÉ INFORMÁCIE

Pred použitím si prečítajte nasledovné

informácie a odložte si ich pre budúcu

potrebu

POMEMBNA INFORMACIJA

Preberite pred uporabo in shranite za

prihodnjo uporabo

VAŽNE INFORMACIJE

Pročitati prije upotrebe i sačuvati za

buduće osvrte

LT

Operatoriaus instrukcijų rinkinys

Perskaitykite šį instrukcijų rinkinį labai atidžiai,

kad pilnai suprastumėte turinį, prieš

pradėdami naudoti vejos/ žolės pjovėją.

RU

 

  ,  

,    

.

EE

OLULINE TEAVE

Enne seadme kasutuselevõtmist lugege

kasutusjuhend läbi ning säilitage see tuleviku

tarbeks.

LV

SVARŒGA INFORMĀCIJA

Pirms lietošanas izlasiet un saglabājiet

turpmākām uzziņām

RO

Manual de instrucţiuni

Inainte să folosiţi mașina de tuns pentru

prima oară, citiţi cu atenţie manualul de

instrucţiuni pentru a-i înţelege conţinutul.

GR

ΣΗΜΑΝΤΙΚΕΣ ΠΛΗΡΟΦΟΡΙΕΣ

ιαβάστε αυτό το φυλλάδιο πριν από τη

χρήση της συσκευής και φυλάξτε το για

ελλοντική αναφορά

TR

ÖNEMLİ BİLGİLER

Kullanmadan önce okuyunuz ve ileride

başvurmak üzere saklayınız.

5052866-01 Easicut 500CT Euro.qxp:5052866-01 Easicut 500CT Euro.qxp 26/1/11 15:29 Page 2

1

GB - CONTENTS

1. Switch levers

2. Handguard

3. Blade cover

4. Battery Charger

5. Battery Cradle

6. Battery

7. Product Rating Label

8. Warning Label

9. Instruction Manual

DE - INHALT

1. Ein/Aus-Schalter

2. Schnittschutz

3. Klingenschut

4. Akkuladegerät

5. Akkuhalterung

6. Akku

7. Produkttypenschild

8. Warnetikett

9. Bedienungsanweisung

FR - TABLE DES MATIÈRES

1. Poignée à double

commande

2. Ecran protecteur

3. Fourreau protège-lames

4. Chargeur de batterie

5. Support batterie

6. Batterie

7. Plaquette des

Caractéristiques du Produit

8. Etiquette dʼavertissement

9. Manuel dʼinstructions

NL - INHOUD

1. Schakelhendels

2. Handbescherming

3. Messchede

4. Batterijoplader

5. Batterijhouder

6. Batterij

7. Product-informatielabel

8. Waarschuwingsetiket

9. Handleiding

NO - INNHOLD

1. Bryterhåndtak

2. Beskyttelscsskjerm/hand-

beskytter

3. Bladbeskytter

4. Batterilader

5. Batterikrybbe

6. Batteri

7. Produktmerking

8. Advarselsetikett

9. Bruksanvisning

FI - SISÄLTÖ

1. Käynnistysvivut

2. Kädensuoja

3. Teränsuoja

4. Akkulaturi

5. Akun teline

6. Akku

7. Ruohonleikkurin arvokilpi

8. Varoitusnimike

9. Käyttöopas

SE - INNEHÅLL

1. Strömbrytare

2. Handskydd

3. Bladskydd

4. Batterladdare

5. Batterihållare

6. Batteri

7. Produktmärkning

8. Varningsetikett

9. Bruksanvisning

DK - INDHOLD

1. Håndgreb

2. Håndbeskyttelse

3. Klingeskede

4. Batterilader

5. Batteriholder

6. Batteri

7. Produktets mærkeskilt

8. Advarselsmœrkat

9. Brugsvejledning

ES - CONTENIDO

1. Interruptores

2. Defensa

3. Cubierta de la Cuchilla

4. Cargador de pila

5. Soporte para pila

6. Pila

7. Placa de Características del

Producto

8. Etiqueta de Advertencia

9. Manual de Instrucciones

2

3

4

5

6

7

8

9

5052866-01 Easicut 500CT Euro.qxp:5052866-01 Easicut 500CT Euro.qxp 26/1/11 15:29 Page 3

Page is loading ...

SAFETY PRECAUTIONS

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions.

Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future

reference.

The term ʻ“power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark

areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools

create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you

to lose control.

2) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication.

A

moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always wear

eye protection.

Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool.

Carrying power tools with your finger on the

switch or energising power tools that have the switch

on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left

attached to a rotating part of the power tools may

result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of

the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery

or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of

dust collection can reduce dust-related hazards.

3) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power

tool will do the job better and safer at the rate for

which it was designed.

b) Do not use the power tool if the switch does not

turn it on and off.

Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such

preventive safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool.

Power tools are dangerous in the hands

of untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power tool

repaired before use.

Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed.

Use of the power tool for operations

different from those intended could result in a

hazardous situation.

4) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer.

A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another battery pack.

b) Use power tools only with specifically designated

battery packs.

Use of any other battery packs may

create a risk of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins

keys, nails screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may

cause a fire.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush wih water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

5) Service

a) Have your power tool serviced by a qualified

repair person using only identical replacement

parts.

This will ensure that the safety of the power

tool is maintained.

If not used properly this product can be dangerous. The warnings and safety instructions must be

followed to ensure reasonable safety and efficiency in using this product. The operator is responsible

for following the warnings and instructions in this manual and on the product. Never use the product

unless the guards provided by the manufacturer are in the correct position.

ENGLISH - 1

Explanation of Symbols on your product

Warning.

Read the user instructions carefully to

make sure you understand all the controls

and what they do.

Do not expose to rain.

Do not leave the product outdoors while it

is raining.

The use of eye protection is

recommended.

5052866-01 Easicut 500CT Euro.qxp:5052866-01 Easicut 500CT Euro.qxp 26/1/11 15:29 Page 7

Hedge trimmer safety warnings:

• Keep all parts of the body away from the cutter blade.

Do not remove cut material or hold material to be cut

when blades are moving. Make sure the switch is off

when clearing jammed material.

A moment of

inattention while operating the hedge trimmer may

result in serious personal injury.

• Carry the hedge trimmer by the handle with the cutter

blade stopped. When transporting or storing the

hedge trimmer always fit the cutting device cover.

Proper handling of the hedge trimmer will reduce

possible personal injury from the cutter blades.

• Hold the power tool by insulated gripping surfaces

only, because the cutter blade may contact hidden

wiring.

Cutter blades contacting a "live" wire may

make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

• Keep cable away from the cutting area.

During

operation the cable may be hidden in shrubs and can

be accidentally cut by the blade.

Additional Safety Recommendations

Work area safety

1. Never allow children or people unfamiliar with these

instructions to use the product. Local regulations

may restrict the age of the operator.

2. Only use the product in the manner and for the

functions described in these instructions.

3. The operator or user is responsible for accidents or

hazards occurring to other people or their property.

Personal safety

1. Always wear suitable clothing, gloves, and stout

shoes.

2. Thoroughly inspect the area where the product is to

be used and remove all wires and other foreign

objects.

3. Before using the machine and after any impact,

check for signs of wear or damage and repair as

necessary.

4. Always ensure the hand guard supplied is fitted

before using the hedge trimmer. Never attempt to

use an incomplete product or one with an

unauthorised modification.

5. This product has not been designed to provide

protection from electric shock in the event of contact

with overhead electric lines.

Power tool use and care

1. Know how to stop the product quickly in an

emergency.

2. Never hold the product by the guard.

3. Never operate the product with damaged guards or

without guards in place.

4. Do not use stepladders whilst operating the product.

5. Use the Hedgetrimmer only in daylight or good

artificial light.

6. Avoid operating your Hedgetrimmer on a wet hedge,

where feasible.

7.

Keep hands and feet away from the cutting means

at all times and especially when switching on the

motor.

8. Remove the battery pack:-

- before leaving the product unattended for any period;

- before clearing a blockage;

- before checking, cleaning or working on the

appliance;

- if you hit an object. Do not use your product until you

are sure that the entire product is in a safe operating

condition;

- if the product starts to vibrate abnormally. Check

immediately. Excessive vibration can cause injury.

- before passing to another person.

Maintenance and storage

1. Keep all nuts, bolts and screws tight to be sure

the product is in safe working condition.

2. Replace worn or damaged parts for safety.

3. Be careful during adjustment of the

Hedgetrimmer to prevent entrapment of the

fingers between moving blades and fixed parts

of the machine.

4. After use the product should be stored using the

blade cover provided.

5. Store in a cool dry place and out of reach of children.

Do not store outdoors.

6. Allow the product to cool for at least 30 minutes

before storing.

Battery

Cordless Battery Powered Products require special

care.

1. AVOID ACCIDENTAL STARTING KEEP HANDS AND

FINGERS AWAY FROM THE SWITCH LEVER WHILE

CARRYING THE PRODUCT.

2. Always charge the product indoors and store in a cool

dry place - out of the reach of children.

3. Use the charger with standard domestic household

electrical outlets only.

4. Do not abuse the charger or charger cord.

5. Do not use the charger if the charger or charger

cord is damaged.

6. Do not charge the battery or use the unit in an

explosive or corrosive environment. Avoid areas

where flammable liquids or gases are present to

avoid creating a fire or explosion.

7. Do not attempt to repair the unit including the battery.

Nylon line replacement and cleaning the unit are the

only items suitable for user maintenance.

8. Do not insert any object into the motor area. Keep

free of debris to avoid overheating.

9. Do not incinerate or mutilate the battery. Batteries

contain hazardous chemicals. Dispose of properly.

SAFETY PRECAUTIONS

ENGLISH - 2

5052866-01 Easicut 500CT Euro.qxp:5052866-01 Easicut 500CT Euro.qxp 26/1/11 15:29 Page 8

GUARANTEE AND GUARANTEE POLICY

If any part is found to be defective due to faulty

manufacture the guarantee period, Husqvarna UK Ltd.,

through its Authorised Service Repairers will effect the

repair or replacement to the customer free of charge

providing:

(a) The fault is reported directly to the Authorised

Repairer.

(b) Proof of purchase is provided.

(c) The fault is not caused by misuse, neglect or faulty

adjustment by the user.

(d) The failure has not occurred through fair wear and

tear.

(e) The machine has not been serviced or repaired,

taken apart or tampered with by any person not

authorised by Husqvarna UK Ltd..

(f) The machine has not been used for hire.

(g) The machine is owned by the original purchaser.

(h) The machine has not been used commercially.

* This guarantee is additional to, and in no way

diminishes the customers statutory rights.

Failures due to the following are not covered, therefore it

is important that you read the instructions contained in

this Operator's Manual and understand how to operate

and maintain your machine:

Failures not covered by guarantee

* Failures as a result of not reporting an initial fault.

* Failures as a result of sudden impact.

* Failures as a result of not using the product in

accordance with the instructions and

recommendations contained in this Operator's Manual.

* Machines used for hire are not covered by this

guarantee.

* The following items listed are considered as wearing

parts and their life is dependent on regular

maintenance and are, therefore not normally subject

to a valid warranty claim: Blades.

* Caution!

Husqvarna UK Ltd. does not accept liability under the

warranty for defects caused in whole or part, directly or

indirectly by the fitting of replacement parts or additional

parts that are not either manufactured or approved by

Husqvarna UK Ltd., or by the machine having been

modified in any way

ENGLISH - 3

Service Recomendations

• Your product is uniquely identified by a silver and black product rating label.

• We strongly recommend that your product is serviced at least every twelve months, more often in a professional application.

Environmental Information

• Awareness of the environment must be considered

when disposing of ʻend-of-lifeʼ product.

• If necessary, contact your local authority for disposal

information.

BATTERY DISPOSAL

•

This product contains a NiCd battery and should not

be discarded with normal household waste at the end

of its life.

• The battery must be removed from the product before

disposal.

• The battery should be disposed of safely.

• Do NOT dispose of used battery with household waste.

• Do NOT dispose of battery to water.

• NiCd batteries can be harmful and should be

disposed of through the recognised recycling facility

in accordance with European Regulations.

• Do NOT incinerate.

The symbol on the product or on its packaging

indicates that this product may not be treated as

household waste. Instead it shall be handed over to the

applicable collection point for the recycling of electrical

and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential

negative consequences for the environment and human

health, which could otherwise be caused by

inappropriate waste handling of this product. For more

detailed information about recycling of this product,

please contact your local council office, your household

waste disposal service or the shop where you

purchased the product.

Battery

Battery Care

1. If over a period of time the battery quickly runs down

after a full 5-6 hour charging period, a replacement

battery is needed.

2. There will be some charge present in the battery but

to ensure maximum running time, recharge your

product for 5-6 hours before use.

3. To prevent permanent battery damage, never store in

a discharged condition.

4. Contact your local approved service

centre/dealer/distributor for a replacement battery and

for safe disposal of your old battery.

5. Battery

18 Volt 1.7 Amp/Hour "High Power"

No maintenance required

• IMPORTANT

DISPOSE OF YOUR OLD BATTERIES SAFELY

DO NOT CUT OPEN, BURN OR INCINERATE.

Winter Storage

1. Fully charge for 5-6 hours before winter storage.

2. Avoid extended storage without re-charge.

3. Store in a cool dry place.

Charging the Battery

Initial Charging Procedure

1. Use the charger indoors only.

2. Ensure the charger is not exposed to moisture.

3. Plug the charger (B1) into a suitable household

electrical wall socket and switch on.

4. The red indicator lamp (C1) glows continuously

during charging.

5. Full charge will be achieved in 5-6 hours. During

charging the charger becomes warm. This is normal

and means the charger is operating correctly.

Re-Charging Your Product

1. Re-charge the battery as soon as the cutting power

of your product begins to die and slow down.

2. Avoid running the product into "deep" discharge, i.e.

avoid flattening the battery completely.

3. Follow the procedure outlined in the Initial

Charging Procedure.

4. Charging the battery according to these instructions

should ensure maximum battery life.

5052866-01 Easicut 500CT Euro.qxp:5052866-01 Easicut 500CT Euro.qxp 26/1/11 15:29 Page 9

ECC500

50

93

101

82

2.5

0.58

1.5

3.2

ENGLISH - 4

EC DECLARATION OF CONFORMITY

Husqvarna AB, 561 82, Huskvarna, Sweden

Declare under our sole responsibility that the product(s);

Category............................

Battery Hedgetrimmer

Type(s) ............................ECC500

Identification of Series.......See Product Rating Label

Year of Construction..........See Product Rating Label

Conforms to the essential requirements & provisions of the following EC Directives:

2006/42/EC, 2004/108/EC, 2000/14/EC

based on the following EU harmonized standards applied:

EN60745-1, EN60745-2-15, EN50366, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3

The maximum A weighted sound pressure level L

pA

at the workstation, measured

according to EN60745-2-15, recorded on a sample of the above product(s) corresponds

to the Level given in the table.

The maximum hand / arm vibration weighted value measured according to EN60745-2-15

on a sample of the above product(s) corresponds to the Value a

h

given in the table.

The declared vibration total value has been measured in accordance with a standard test

method and may be used for comparing one tool with another.

The declared vibration total value may also be used in a preliminary assessment of

exposure.

Warning:

The vibration emission during actual use of the power tool can differ from the declared

total value depending on the ways in which the tool is used

Operators should identify safety measures to protect themselves that are based on an

estimation of exposure in the actual conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is switched off and when it is running idle

in addition to the trigger time).

2000/14/EC: The Measured Sound Power L

WA

& Guaranteed Sound Power L

WA

values are

according to the tabulated figures.

Conformity Assessment Procedure............... Annex V

Notified Body................................................. Intertek, Cleeve Road

Leatherhead, Surrey

KT22 7SB, England

Ulm 26/01/2011

P. Lamelli

Global R&D Director - Hand held

Keeper of technical documentation

Type

Blade length (cm)

Measured Sound Power L

WA

(dB(A))

Guaranteed Sound Power L

WA

(dB(A))

Level L

pA (dB(A))

Uncertainty K

pA(dB(A))

Value a

h

(m/s

2

)

Uncertainty K

ah (m/s

2

)

Weight (Kg)

5052866-01 Easicut 500CT Euro.qxp:5052866-01 Easicut 500CT Euro.qxp 26/1/11 15:30 Page 10

Page is loading ...

5052866-01

BELGIQUE/BELGIË Husqvarna BELGIUM NV,

BERGENSESTEENWEG 719, 1502 LEMBEEK

Tel: 02 363 0311, Fax: 02 363 0391

ČESKÁ REPUBLIKA Husqvarna Cesko s.r.o., oz Husqvarna Outdoor Products,

Dobronická 635, 148 25 Praha 4

Tel: 02/6111 2408-9, Info-linka: 0800/110 220

Internet: www.partner-flymo.cz E-mail: [email protected]

DANMARK Flymo/Partner A/S,

Lundtoftegårdsvej 93A, 2800 Kgs.Lyngby

Tel: 4587 7577, Fax: 45933308, www.flymo-partner.dk

DEUTSCHLAND Husqvarna Deutschland GmbH,

Julius Hofmann Str. 4, 97469 Gochsheim

Tel: 097 21 7640, Fax:097 21 764202

ESTONIA Husqvarna Eesti OÜ,

Mustamäe tee 24, 10621 Tallinn

Tel: +372 6650030

FRANCE Husqvarna Jardin SAS54,

54, rue Lambrechts, BP316, 92402 COURBEVOIE cedex

Tel 01 46 67 8141, Fax 01 43 34 2491

FINLAND SUOMI OY Husqvarna AB,

PL185, 00511 HELSINKI

Tel: 00 39611, Fax: 00 39 612632

ITALIA McCulloch Italiana s.r.l.

Via Como 72, 23868 Valmadrera (LECCO)

Tel: 800 017829, Fax: 0341 581671

IRELAND Flymo Ireland

Tel: 01 4565222, Fax: 01 4568551

MAGYARORSZÁG Husqvarna Magyarország Kft.,

1142 Budapest, Erzsébet királyné u. 87

Tel: 06-1-467 32 72, Fax: 06-1-221 50 56

NORGE Flymo/Partner, div. av Husqvarna Norge AS

Postboks 200, 1541 Vestby

Tel: 69 10 47 90

NEDERLAND Husqvarna Nederland BV,

Vennootsweg 1, 2404 CG Alphen aan den Rijn

Tel: +31(0) 172468322, Fax: +31(0) 172468219

ÖSTERREICH HUSQVARNA Zentralwerkstätte, Industriezeile 36, 4020 LINZ,

Tel: 0732 770101-60, Fax: 0732 795922

POLSKA Husqvarna Poland Sp. z.o.o.

03-371 Warszawa, ul. Wysockiego 15B

Tel:- (22) 8332949

SLOVENIJA SKANTEH d.o.o.

Tel:- (061) 133 70 68, Fax:-(061) 133 70 68

SLOVENSKA Husqvarna Slovakia s.r.o., Borova Sihot 211, 033 01 Lipt. Hradok

Tel: 044 522 14 19, Fax: 044 522 14 18, www.flymo-partner.sk

SCHWEIZ/SUISSE/SUIZZERA Husqvarna Schweiz AG,

Industriestrasse 10, 5506 Mägenwil

Tel 062/889 93 50, Fax 062/889 93 60

SVERIGE Husqvarna AB, Sverige

Tel: 036 – 14 67 00, Fax: 036 – 14 60 70

UNITED KINGDOM Husqvarna Outdoor Products United Kingdom

Tel: 0870 609 1905, Fax: 0870 609 1904

Husqvarna AB

561 82 Huskvarna

Sweden

Our policy of continuous improvement means that the specification of products may be altered from time to time

without prior notice.

unregistered trademarks of Flymo S.A.

5052866-01 Easicut 500CT Euro.qxp:5052866-01 Easicut 500CT Euro.qxp 26/1/11 15:32 Page 104

Flymo EasiCut 500CT Owner's manual

Related papers

Other documents