F20293B EN (040308J)

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information,

call 1-888-VIKING1 (845-4641)

or visit the Viking Web site at

cooker is placed on the mounting bracket located on the cart directly under the hinge. The hinge and the inside

damper vent should be used for hand holds. (See Figure 3).

6. Re-install dome, hinge nuts and

washers. Remove shipping screws

from each side of hinge. Replace

inside parts

support bracket

Cooker shelf

Figure 3

Mounting Bracket

(located behind

To mount the cooker to the cart:

Always wear gloves when installing the cooker. Although the cooker and cart is deburred prior to shipment, some

edges may still be sharp enough to cause injury during handling.

1. Remove the stainless steel side burner cover, side burner grates, burner bowls and grate support. (41” W. models

only)

2. Remove the top from the cart. (See Figure 1)

CAUTION: Keep hands and fingers away fro spring area.

3. Install two (2) shipping screws, (one set on each side). (See Figure 2) Remove the two (2) top nuts and washers on

each side of the hinge mount.

4. Remove all inside parts.

Figure 2

CART DIMENSIONS

61-3/4” (156.9 cm)

37-7/8” (96.2 cm)

29-3/8” (77.6 cm)

37-5/8”

(95.6 cm)

23-7/8” (60.6 cm)

31-5/8” (79.7 cm)

Cart Door Adjustment (41” W. Model only)

loosen the screw and slide the door in or out. Retighten the screw to secure the door.

4

BASIC SPECIFICATIONS

LP/Propane: Equipped with high

capacity hose/regulator

assembly for connection to

standard 5 gal, 20 lb.

LP/Propane gas cylinder

with Type 1, QCC-1

connection or standard

residential 1/2” (1.3 cm) ID

gas service line

41-1/4” (104.8 cm)

73-3/8” (186.4 cm)

36-1/2”

(92.7 cm)

37-1/2”

(95.3 cm)

24” (104.8 cm)

61-3/4” (156.7 cm)

73-3/8” (186.4 cm)

41-3/16” (104.6 cm)

NATURAL FIXED PIPING CONNECTION

Connection: Standard Residential 1/2” ID gas service line - 1/2” NPT male with 1/2” flare adapter.

Operating Pressure: 4.0” W.C.P. Nat.

Supply Pressure: 6” to 14” W.C.P. Nat. If in excess of 14” W.C.P., a step-down regulator is required.

Check with your local gas utility company or with local codes for instructions on installing gas supply lines. Be sure to check on

type and size of run and how deep to bury the lines. If the gas line is too small, the grill will not function properly.

To connect the supplied regulator assembly to the incoming flexible gas line, attach with a 1/2” (1.3 cm) female flare adaptor

adapter

Type 1, QCC-1

connector

Tank

LP/PROPANE TANK REQUIREMENTS

A dented or rusty LP/Propane tank may be hazardous and should be checked by your tank supplier. Never use a cylinder

with a damaged valve. All tanks should be equipped with an OPD (overfilling protection device). This is a DOT

requirement for all tanks purchased after October 1, 1998 and will ensure that the tank is not overfilled. The LP/Propane

tank should be a standard 5-gal, 20 lb. gas cylinder tank approximately 12” in diameter and 18” high which must be

is stored indoors the cylinder must be disconnected and removed from the appliance. Cylinders must be stored outdoors

in a well-vented area out of the reach of children.

LP/PROPANE FIXED PIPING CONNECTION

Connection: Standard Residential 1/2” ID gas service line - 1/2” NPT male with 3/8” flare adapter.

Operating Pressure: 10.0” W.C.P. Nat.

the regulator assembly to the 3/8” male flare adaptor on the grill.

DO NOT forget to place the installer supplied gas valve in an accessible location.

1/2” female

flare

1½”

FLAME HEIGHT

BURNER ADJUSTMENT

Each burner is tested and adjusted at the factory prior to shipment; however, variations in the local gas supply may make

it necessary to adjust the burners. The flames of the burners should be visually checked and compared with flame height

drawing below.

Flames should be blue and stable with no yellow tips, excessive noise or lifting. If any of these conditions exist,

2. If the flame is noisy and lifting away from the burner, turn the air shutter clockwise to reduce the amount of

air to the burner.

Once adjusted, turn the burner off, tighten the set screw on the air shutter, replace the grate support, burner bowls, and

grates. To ensure proper installation of the side burners, slide opening in air shutters over the orifice located in the front

of the unit.

LEAK TESTING

Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete gas tightness check

must be performed at the installation due to possible mishandling in shipment or excessive pressure unknowingly being

applied to the unit. Periodically check the whole system for leaks, or immediately check if the smell of gas is detected.

7. Stop a leak by tightening the loose joint or by replacing the faulty part with a replacement part recommended by the

manufacturer. Do not attempt to repair the cylinder valve if it should become damaged. The cylinder must be

replaced.

8. If you are unable to stop a leak, shut off the gas supply at the cylinder valve. Remove the cylinder from the grill. Call

an authorized gas appliance service technician or LP/Propane gas dealer. Do not use the grill until the leak is

corrected.

9. After checking for leaks, push in and turn any control knob to release the pressure in the hose and manifold. Turn off

the control knob.

Before placing into operation, always check for gas leaks with a soapy