SMC SMCWBR14T-G User manual

SMCWBR14T-G

SMCWBR14T-G 802.11g 108Mbps

Wireless Barricade™ Router

Model Number: SMCWBR14T-G

Quick Installation Guide

Installationskurzanleitung

Guide d’installation rapide

Manual de instalación rápida

Snabbinstallationshandbok

Beknopte installatiehandleiding

Manual de Instalação Rápida

802.11g 108Mbps Wireless Barricade™ Router

802.11g 108 Mbit/s Wireless Barricade™ Router

Routeur Barricade™ sans fil 802.11g 108Mbps

Barricade™ Router inalámbrico 802.11g de 108 Mbps

802.11g 108Mbit/s trådlös Barricade™-router

802.11g 108Mbps Wireless Barricade™ Router

Router Sem Fios de 108 Mbps 802.11g Barricade™

SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 1

1

English

2

Contents

After unpacking the SMCWBR14T-G Router, please check the

contents of the box to be sure you have received the following

components:

•One Barricade™ SMCWBR14T-G 802.11g Wireless Router.

•One Power Adaptor.

•One Ethernet Cable.

•One CD-ROM.

Immediately inform your dealer in the event of any incorrect,

missing or damaged parts. If possible, please retain the carton

and original packing materials in case there is a need to return

the product.

Please register this product and upgrade the product warranty

at SMC's Web site: www.smc.com.

Package Contents

English 2-13

Deutsch 14-25

Français 26-37

Español 38-49

Svenska 50-61

Nederlands 62-73

Português 74-85

Compliances & Information 86-89

Table of Contents

SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 1

English

4

English

3

Front

1. Power (PWR) LED

When this blue LED is on, the router is powered up.

2. WAN LEDs

When the WAN LED has a solid blue light on, means there is an

active connection to the DSL/Cable modem. The PPPoE/DSL LED

beneath will show any activity of the WAN connection.

3. Wireless LAN (WLAN) LED

When this blue LED is on, wireless networking is enabled.

The LED will flash when data is sent or received over a wireless

connection.

4. LAN LEDs (LAN1, LAN2, LAN3 and LAN4)

There are two LEDs — one above the other — for each LAN

(Local Area Network) (see 7).

The top LED is green and the bottom is amber. These two LEDs

behave in exactly the same way as the WAN LEDs.

Hardware Description

System Requirements

To install and connect to the SMCWBR14T-G, you must have:

• An external Cable or DSL modem with an Ethernet port.

• An account with an ISP for Cable or DSL access.

•A Computer with a CD-ROM drive and working Ethernet port.

•Windows (98 or later), MacOS (9.x or later) or Linux.

• An up to date web browser:

• Internet Explorer 5.5 or later.

• Mozilla 1.7/Firefox 1.0 or later.

Note: A CD-ROM drive required to read the manual and if you want

to use the EZ 3-Click Installation Wizard application to

configure your Barricade™ Router. The installation process

can be completed manually through the web interface.

1

2

3

4

SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 3

English

5

English

6

5

Back

5. Power

Connect the supplied, 12V power adapter to this socket.

6. WAN Port

Use the supplied Ethernet cable to connect the WAN port to your cable

or DSL modem. The associated LED on the front panel will light up

when the connection is made.

7. LAN Ports (LAN1, LAN2, LAN3 and LAN4)

There are four Ethernet LAN ports for connection to PCs, network

printers or similar devices. Note the labelling; one pair of LAN LEDs on

the front panel is associated with one port on the rear panel.

If a device is not correctly connected, using a suitable Ethernet cable,

the associated LED will not turn on.

8. Reset

If, for any reason, you need to reset the unit to factory defaults

and cannot access the user interface (e.g. if you have changed

and forgotten the password), press the reset button for 10 seconds.

Note that you will lose all your configuration changes.

Ethernet Cables

One Ethernet cable, intended for your WAN connection, is bundled

with the router. You can use this as a point of reference for

purchasing other cables; the cable is constructed from unscreened,

“Cat 5” cable with RJ45 connecters at both ends. Cables of this

type can be purchased at most computer retailers.

The position of your Router is important to its wireless

performance. The Router should be located in a central position

relative to the wireless PCs that will connect to it. A suitable

location might be on a high shelf or a similar position that allows

good wireless coverage from the Router to the wireless PCs.

To meet the FCC wireless radiation exposure regulations, the Router

should be located in a position to maintain a minimum distance of

20cm (8 inches) from any personnel.

Connect all of the computers that you want to share on your

internet connection to your router. Connect your broadband

modem to the WAN port of the router.

During the initial setup, SMC recommend that the Router is

configured from a wired Ethernet PC as shown in the diagram.

Hardware Installation

WIRELESS

ROUTER

BROADBAND

MODEM

WIRELESS

LAPTOP

INTERNET

8

7

65

SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 5

If you want to mount this particular product onto the wall, please

use the holes at the bottom of this router as shown on the below

picture.

Follow the steps in this section after connecting your network as

described in the previous section.

Before beginning make sure you have all the details about your

internet connection from your ISP.

1. First, power-up your modem, then the router and finally power-

up the PC that you will use to configure the router.

2. Start your web browser and enter the address

http://192.168.2.1. If your PC is properly configured you will

see the login page of the router. If you cannot access the login

page then you must first reconfigure your PC to obtain an IP

address automatically; see the manual on the CD-ROM for more

information.

English

8

English

7

3. If you are using Windows, you now have the option of running

the EZ 3-Click installation wizard. If you are using another

operating system (e.g. MacOS or Linux) or require more help

than EZ 3-Click can provide, continue to step 4.

4. Type in the password (the default is smcadmin) and click on

Login. When you have successfully logged in, you will see the

Overview page which allows you to choose between the Setup

Wizard and Advanced Setup. Select Setup Wizard.

5. Click next to start the Setup Wizard. Here you will be able to

change the basic wireless settings such as SSID, Channel, Range

Extender and wireless operating mode. Click Next when finished

to move forward.

6. The next page of the wizard allows you to select your

broadband-connection type. Clicking on an option will

automatically move you to the next page. Read the text on this

screen carefully before making your choice.

7. The next page will ask you for technical information about your

internet connection. Your ISP should have provided you with

the information required to fill in this page. If you do not have

the required information then you may have picked the wrong

connection type during stage 6; you can click on the Back

button to try another connection type. When you have filled in

all the necessary details, click on the Finish button.

Important Note: If you are on a metered internet connection,

you should set your Maximum Idle Time to 1 minute.

8. That's It! You should be connected to the Internet.

Please register your product by pointing your Web browser to

http://www.smc.com and clicking through to the support pages.

If you are not connected to the Internet, please contact your ISP

to clarify your connection details.

Initial Configuration

SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 7

English

10

English

9

To setup Wireless networking you must select Home Network Settings

-> Wireless option in the Configuration menu.

1. To create a wireless network, the Router and wireless PCs must have

the same SSID and encryption settings. The default wireless

settings for the Router are shown below:

SSID - Router default is SMC

The SSID is the name given to your wireless LAN. Only PCs with the

same SSID as the Router can connect to the wireless LAN.

Wireless Encryption - Router default is off

To set up your wireless network, set the encryption to off in both

the Router and the wireless PC. Wireless encryption can be set

up later, after you have established a wireless network.

Wireless Channel - Router default is 6

The wireless channel is set in the Router and the default is

channel 6. The wireless PCs will automatically scan the channels to

detect which channel the Router is using.

If this is your only wireless network, then you can use the Router's

default settings. Now set your wireless PC to have the same SSID

and encryption settings as the Router. The wireless PCs must be set

to use infrastructure mode.

If your computer has both a wired and wireless connection

installed, then you must ensure that only one type is used at a

time, to connect to the LAN. To use the wireless connection,

unplug the wired Ethernet cable and reboot the PC.

Once you have setup the same SSID and Encryption in the Router and

wireless PC, open a browser and try to connect to www.smc.com. If

you can access the internet, then you have successfully set up your

wireless LAN.

Wireless Networking

The EZ 3-Click Application runs on Windows only and provides:

• An alternative approach to initial configuration.

• Access to the User Guide.

• Installation of Zone Alarm and Adobe Acrobat Reader.

To use EZ 3-Click, place the supplied CD in the CD-ROM drive of the

PC that is connected to the router. If your PC is configured to

auto-play CDs, the following dialog will appear on your screen.

If the dialog does not appear, you will have to start the

application manually. Do this by first opening Windows Explorer

then opening the folder associated with your CD-ROM drive. Once

you have opened the folder you will see the file SMCWBR14T-G.exe.

Run this file by double-clicking on it.

EZ Installation CD

SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 9

English

12

English

11

Installation Troubleshooting

• Check that the Power Adapter is switched on and is connected

to the Router. The green PWR LED on the Router should be on.

Use only the power adapter that was supplied with your Router.

• Check that the DSL or Cable modem, the Router and your PC are

all connected and displaying the correct LEDs.

•The DSL or Cable modem should connect to the WAN port of the

Router using an Ethernet cable. The WAN LED of the Router should

be on.

• The wired PC should connect to a LAN port of the Router using an

Ethernet cable. The corresponding LAN LED of the Router should be

on.

• Power up your equipment in the following order: First the DSL

or Cable modem, then the Router and then your PC. Leave about

1 minute between turning on each device.

• The PC should be setup to obtain an IP address automatically

from the Router's DHCP server. See the user manual on the CD

for details of how to setup your PC to obtain an IP address.

• Check that web proxy is disabled on your PC. Go to the Control

Panel and select Internet Options. Select the Connections tab

and click the LAN Settings button. Check that the Use Proxy

Server option is not ticked.

• Check you can access the Router's web interface. Open a browser

and enter http://192.168.2.1 to access the default IP address

of the Router.

WAN Connection Troubleshooting

• Check that you have selected the correct WAN connection option

and the ISP details are correct. If you do not have these details,

they can be obtained from your ISP.

• If you have any PPPoE client applications already installed on

your PC which were required when your PC was directly

connected to the DSL modem, they must be disabled.

Troubleshooting

2. SMC recommends that you enable wireless encryption to improve

the security of your wireless network. Note that if you change

the wireless settings (e.g. SSID or WEP) of your Router from a

wireless PC, then you may lose contact with your Router.

To re-establish the wireless connection, change the wireless

settings of your PC to be the same as the Router.

SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 11

Deutsch

14

English

13

Prüfen Sie bitte nach dem Auspacken des SMCWBR14T-G Routers

den Packungsinhalt, um sicherzugehen, dass folgende Teile

geliefert wurden:

• Ein Barricade™ SMCWBR14T-G 802.11g Wireless-Router.

• Ein Netzteil.

• Ein Ethernet-Kabel.

• Eine CD-ROM.

Informieren Sie bitte sofort Ihren Händler, wenn Teile fehlen,

falsch sind oder Beschädigungen aufweisen. Heben Sie, wenn

möglich, den Karton und die Originalverpackung auf.

Sie benötigen diese, wenn Sie das Produkt zurücksenden.

Bitte lassen Sie das Produkt registrieren und aktivieren Sie die

Produktgarantie auf der SMC-Website: www.smc.com.

Wireless Troubleshooting

•Check that the SSID is the same for the Router and the wireless PC.

•Check that the wireless encryption is the same on the Router and

the wireless PC. To help debug a problem, turn off encryption in both

the Router and wireless PC until you can establish a connection.

After a change in encryption, some PCs may have to be restarted.

•The wireless PCs must be set to Infrastructure mode to work with

a Router.

• If your computer has both a wired and wireless connection

installed, ensure that the wired Ethernet cable is unplugged.

•Check that the Router WLAN LED is on, to indicate that Wireless

networking is enabled. To enable wireless networking, go to the

Router Wireless page and enable Wireless Networking.

• If there are a number of wireless networks within range, then

you may experience poor wireless performance if the wireless

channels are too close together. Ideally, neighbouring wireless

networks should be at least 5 channels apart. The wireless

channel is controlled by and set in the Router.

•The Router has a feature called MAC Filter which controls which

wireless PCs have access to the wireless LAN. If this feature is

enabled, then ensure that the MAC address of your wireless PC

card is listed in the MAC Filter page.

Lieferumfang

SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 13

Page is loading ...

Compliances

86

Português

85

EC Conformance Declaration – Class B

SMC contact for these products in Europe is:

SMC Networks Europe,

Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 2a,

08970 - Sant Joan Despí,

Barcelona, Spain.

This RF product complies with R&TTE Directive 99/5/EC. For the

evaluation of the compliance with this Directive, the following

standards were applied:

• Electromagnetic compatibility and radio spectrum matters (ERM)

EN300 328-1 (2001-12)

EN300 328-2 (2001-12)

• Electromagnetic Compatibility (EMC) Standard for radio

equipment and services

EN301 489-1

EN301 489-17

• Safety Test

EN60950

Warning

In a domestic environment this product may cause radio

interference in which case the user may be required to take

adequate measures.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

Compliances

• Se tiver quaisquer aplicações de cliente PPPoE instaladas no PC,

necessárias na altura em que o PC foi directamente ligado ao

modem ADSL, estas terão de ser desactivadas.

Resolução de Problemas de Ligações Sem Fios

• Certifique-se de que o SSID do router é igual ao do PC sem fios.

• Certifique-se de que a encriptação sem fios do router é igual à do PC

sem fios. Para ajudar a resolver um problema, desactive a encriptação

tanto no router como no PC sem fios, até poder estabelecer uma

ligação. Após uma alteração de encriptação, alguns PCs podem ter de

ser reinicializados.

• Os PCs sem fios têm de ser configurados para o modo de infra-

estrutura, para funcionarem com um router.

• Se o seu computador tiver instalada uma ligação por cabo e uma

ligação sem fios, certifique-se de que o cabo Ethernet está

desligado.

• Certifique-se de que o LED [WLAN] do router está aceso, para

indicar que a ligação de rede sem fios está activa. Para activar a

ligação de rede sem fios, aceda à página [Router Wireless]

(Router sem fios) e active [Wireless Networking] (Ligação de

rede sem fios).

• Se existirem algumas redes sem fios na mesma área de cobertura,

poderá constatar um fraco desempenho no caso dos canais sem

fios estarem demasiado próximos. Preferencialmente, as redes

sem fios próximas devem estar pelo menos 5 canais à parte. O

canal sem fios é controlado e definido no router.

•O router possui uma função denominada MAC Filter (Filtro MAC),

que controla quais os PCs sem fios que têm acesso à LAN sem

fios. Se esta função estiver activa, certifique-se de que o

endereço MAC da placa de PC sem fios está incluído na página

[MAC Filter] (Filtro MAC).

SMCWBR14T_G_QIG.qxd 10/06/05 15:55 Page 85

Information

88

Compliances

87

Full Installation Manual

Full installation manuals are provided on the Installation CD-Rom.

Manuals in other languages than those included on the CD-Rom

are provided on www.smc.com (section support).

Firmware and Drivers

For latest driver, technical information and bug-fixes please visit

www.smc.com (section support).

Limited Lifetime Warranty Statement

For detailed information on SMC’s limited lifetime warranty

please check the English full manual on this CD-Rom or visit

www.smc.com (section support, product registration).

Contact SMC

Contact details for your relevant countries are available on

www.smc.com.

CompliancesCompliancesInformati

on

Information

However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly

approved by the party responsible for compliance could void

the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

IMPORTANT NOTE:

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. This equipment should

be installed and operated with minimum distance 20cm between

the radiator & your body.

This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Industry Canada - Class B

This digital apparatus does not exceed the Class B limits for radio

noise emissions from digital apparatus as set out in the

interference-causing equipment standard entitled “Digital

Apparatus” ICES-003 of the Department of Communications.

SMCWBR14T_G_QIG.qxd 10/06/05 15:55 Page 87

90

Information

89

Statement of Conditions

In line with our continued efforts to improve internal design,

operational function, and/or reliability, SMC reserves the right

to make changes to the product(s) described in this document

without notice. SMC does not assume any liability that may occur

due to the use or application of the product(s) described herein.

In order to obtain the most accurate knowledge of installation,

bug-fixes and other product related information we advise to visit

the relevant product support page at www.smc.com before you

start installing the equipment. All information is subject to change

without notice.

Limitation of Liability

In no event, whether based in contract or tort (including

negligence), shall SMC be liable for incidental, consequential,

indirect, special or punitive damages of any kind, or for loss of

revenue, loss of business or other financial loss arising out of

or in connection with the sale, installation, maintenance, use,

performance, failure or interruption of its products, even if SMC

or its authorized reseller has been adviced of the possiblity of

such damages.

Copyright

Information furnished by SMC Networks, Inc. (SMC) is believed

to be accurate and reliable. However, no responsibility is assumed

by SMC for its use, nor for any infringements of patents or other

rights of third parties which may result from its use. No license

is granted by implication or otherwise under any patent or patent

rights of SMC. SMC reserves the right to change specifications at

any time without notice.

Trademarks

SMC is a registered trademark and Barricade™ is a trademark

of SMC Networks, Inc. Other product and company names are

trademarks or registered trademarks of their respective holders.

SMCWBR14T_G_QIG.qxd 10/06/05 15:55 Page 89

SMC SMCWBR14T-G User manual

SMC SMCWBR14T-G User manual

in other languages

Related papers

Other documents