Cisco Catalyst 3750V2-48TS Switch User manual

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Catalyst 3750, 3560, 3550, 2975, 2970,

and 2960 Switch System Message Guide

Cisco IOS Release 12.2(46)SE and Release 12.2(46)EX

November 2008

Text Part Number: OL-8551-04

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR

IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, the Cisco logo, DCE, and Welcome to the Human Network

are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To

You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco

Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems,

Cisco

Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing,

FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort

logo, LightStream, Linksys, MediaTone, MeetingPlace,

MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet,

Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx

logo are registered trademarks of Cisco Systems, Inc.

and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0809R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the

document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

iii

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

CONTENTS

Preface vii

Audience i-vii

Purpose i-vii

Conventions i-vii

Related Publications i-viii

Obtaining Documentation, Obtaining Support, and Security Guidelines i-x

CHAPTER

2 System Message Overview 2-1

How to Read System Messages 2-1

Error Message Traceback Reports 2-7

Output Interpreter 2-7

Bug Toolkit 2-7

Contacting TAC 2-7

CHAPTER

3 Message and Recovery Procedures 3-1

ACLMGR Messages 3-3

AUTOQOS Messages 3-8

BACKUP_INTERFACE Messages 3-8

BADTRANSCEIVER Messages 3-9

BSPATCH Messages 3-9

CFGMGR Messages 3-10

CMP Messages 3-13

DHCP_SNOOPING Messages 3-14

DHCP_SNOOPING_CAT3550 Messages 3-17

DOT1Q_TUNNELLING Messages 3-18

DOT1X Messages 3-18

DOT1X_SWITCH Messages 3-19

DTP Messages 3-23

DWL Messages 3-24

EC Messages 3-25

ENVIRONMENT Messages 3-29

ETHCNTR Messages 3-30

Contents

iv

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

EXPRESS_SETUP Messages 3-34

FM Messages 3-35

FRNTEND_CTRLR Messages 3-44

GBIC Messages 3-45

GBIC_SECURITY Messages 3-48

GBIC_SECURITY_CRYPT Messages 3-51

GBIC_SECURITY_UNIQUE Messages 3-52

GIGASTACK Messages 3-53

HARDWARE Messages 3-54

HLFM Messages 3-56

HPSECURE Messages 3-57

IDBMAN Messages 3-58

IGMP_QUERIER Messages 3-61

ILPOWER Messages 3-62

IMAGEMGR Messages 3-69

IP_DEVICE_TRACKING_HA Messages 3-70

L2TM Messages 3-71

L3TCAM Messages 3-71

MAC_LIMIT Messages 3-72

MAC_MOVE Messages 3-73

NETWORK_PORT_SATELLITE Messages 3-73

PAGP_DUAL_ACTIVE Messages 3-74

PBR Messages 3-75

PHY Messages 3-77

PIMSN Messages 3-79

PLATFORM Messages 3-80

PLATFORM_FBM Messages 3-81

PLATFORM_HCEF Messages 3-82

PLATFORM_HPLM Messages 3-83

PLATFORM _IPC Messages 3-84

PLATFORM_IPv6 Message 3-85

PLATFORM_PBR Messages 3-86

PLATFORM_PM Messages 3-88

PLATFORM_RPC Messages 3-89

PLATFORM_SPAN Messages 3-91

Contents

v

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

PLATFORM_UCAST Messages 3-92

PLATFORM_VLAN Messages 3-95

PLATFORM_WCCP Messages 3-96

PM Messages 3-97

PORT_SECURITY Messages 3-105

QATM Messages 3-107

QM Messages 3-108

QOSMGR Messages 3-111

RMON Messages 3-117

SDM Messages 3-118

SPAN Messages 3-118

SPANTREE Messages 3-119

SPANTREE_FAST Messages 3-127

SPANTREE_VLAN_SW Messages 3-127

STACKMGR Messages 3-127

STORM_CONTROL Messages 3-130

SUPERVISOR Messages 3-131

SUPQ Messages 3-131

SW_DAI Messages 3-134

SW_MACAUTH Messages 3-137

SW_MATM Messages 3-138

SW_VLAN Messages 3-138

SWITCH_QOS_TB Messages 3-145

TCAMMGR Messages 3-146

UDLD Messages 3-148

UFAST_MCAST_SW Messages 3-150

VQPCLIENT Messages 3-150

WCCP Messages 3-152

WRLSCNTR Messages 3-152

I

NDEX

Contents

vi

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

vii

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Preface

Audience

This guide is for the networking professional managing the Catalyst 3750, 3560, 3550, 2975, 2970, and

2960 switch or switch stack, hereafter referred to as the switch. Before using this guide, you should have

experience working with the Cisco IOS software and the switch software features.

Purpose

This guide describes only the Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 switch-specific system

messages that you might encounter. For a complete list of Cisco IOS system error messages, see the

Cisco IOS Software System Error Messages, Cisco IOS Release 12.2.

This guide does not describe how to install your switch or how to configure software features on your

switch. It also does not provide detailed information about commands that have been created or changed

for use by the switch. For hardware installation information, see the hardware installation guide that

shipped with your switch. For software information, see the software configuration guide and the

command reference for this release.

For documentation updates, see the release notes for this release.

Conventions

This publication uses these conventions to convey instructions and information:

Command descriptions use these conventions:

• Commands and keywords are in boldface text.

• Arguments for which you supply values are in italic.

• Square brackets ([ ]) mean optional elements.

• Braces ({ }) group required choices, and vertical bars ( | ) separate the alternative elements.

• Braces and vertical bars within square brackets ([{ | }]) mean a required choice within an optional

element.

viii

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Preface

Related Publications

Interactive examples use these conventions:

• Terminal sessions and system displays are in screen font.

• Information you enter is in boldface screen font.

• Nonprinting characters, such as passwords or tabs, are in angle brackets (< >).

Notes use this convention and symbol:

Note Means reader take note. Notes contain helpful suggestions or references to materials not in this manual.

Related Publications

These documents provide complete information about the switch and are available from this Cisco.com

site:

Catalyst 3750 switch

http://www.cisco.com/en/US/products/hw/switches/ps5023/tsd_products_support_series_home.html

Catalyst 3560 switch

http://www.cisco.com/en/US/products/hw/switches/ps5528/tsd_products_support_series_home.html

Catalyst 3550 switch

http://www.cisco.com/en/US/products/hw/switches/ps646/tsd_products_support_series_home.html

Catalyst 2975 switch

http://www.cisco.com/en/US/products/ps10081/tsd_products_support_series_home.html

Catalyst 2970 switch

http://www.cisco.com/en/US/products/hw/switches/ps5206/tsd_products_support_series_home.html

Catalyst 2960 switch

http://www.cisco.com/en/US/products/ps6406/tsd_products_support_series_home.html

Note Before installing, configuring, or upgrading the switch, see these documents:

• For initial configuration information, see the “Using Express Setup” chapter in the getting started

guide or the “Configuring the Switch with the CLI-Based Setup Program” appendix in the hardware

installation guide.

• For device manager requirements, see the “System Requirements” section in the release notes (not

orderable but available on Cisco.com).

• For Network Assistant requirements, see the Getting Started with Cisco Network Assistant (not

orderable but available on Cisco.com).

• For cluster requirements, see the Release Notes for Cisco Network Assistant (not orderable but

available on Cisco.com).

• For upgrade information, see the “Downloading Software” section in the release notes.

ix

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Preface

Related Publications

See these documents for other information about the switch:

• Release Notes for the Catalyst 3750, 3560, 3550, 2970, and 2960 Switches

• Catalyst 3750, 3560, 3550, 2970, and 2960 Switch System Message Guide

• Catalyst 3750 Switch Software Configuration Guide

• Catalyst 3750 Switch Command Reference

• Catalyst 3750 Switch Hardware Installation Guide

• Catalyst 3750 Switch Getting Started Guide

• Regulatory Compliance and Safety Information for the Catalyst 3750 Switch

• Catalyst 3560 Switch Software Configuration Guide

• Catalyst 3560 Switch Command Reference

• Catalyst 3560 Switch Hardware Installation Guide

• Catalyst 3560 Switch Getting Started Guide

• Regulatory Compliance and Safety Information for the Catalyst 3560 Switch

• Catalyst 3550 Multilayer Switch Software Configuration Guide

• Catalyst 3550 Multilayer Switch Command Reference

• Catalyst 3550 Multilayer Switch Hardware Installation Guide

• Catalyst 3550 Multilayer Switch Getting Started Guide

• Regulatory Compliance and Safety Information for the Catalyst 3550 Multilayer Switch

• Catalyst 2975 Switch Software Configuration Guide

• Catalyst 2975 Switch Command Reference

• Catalyst 2975 Switch Hardware Installation Guide

• Catalyst 2975 Switch Getting Started Guide

• Regulatory Compliance and Safety Information for the Catalyst 2975 Switch

• Release Notes for the Catalyst 2975 Switches

• Catalyst 2970 Switch Software Configuration Guide

• Catalyst 2970 Switch Command Reference

• Catalyst 2970 Switch Hardware Installation Guide

• Catalyst 2970 Switch Getting Started Guide

• Regulatory Compliance and Safety Information for the Catalyst 2970 Switch

• Catalyst 2960 Switch Software Configuration Guide

• Catalyst 2960 Switch Command Reference

• Catalyst 2960 Switch Hardware Installation Guide

• Catalyst 2960 Switch Getting Started Guide

• Regulatory Compliance and Safety Information for the Catalyst 2960 Switch

• Device manager online help (available on the switch)

• Getting Started with Cisco Network Assistant

• Release Notes for Cisco Network Assistant

• Cisco Small Form-Factor Pluggable Modules Installation Notes

x

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Preface

Obtaining Documentation, Obtaining Support, and Security Guidelines

• Cisco CWDM GBIC and CWDM SFP Installation Note

• Cisco RPS 300 Redundant Power System Hardware Installation Guide

• Cisco RPS 675 Redundant Power System Hardware Installation Guide

• For information about the Network Admission Control (NAC) features, see the Network Admission

Control Software Configuration Guide (Not orderable but available on Cisco.com)

• These compatibility matrix documents are available from this Cisco.com site:

http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html

–

Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix

–

Cisco 100-Megabit Ethernet SFP Modules Compatibility Matrix

–

Cisco Small Form-Factor Pluggable Modules Compatibility Matrix

–

Compatibility Matrix for 1000BASE-T Small Form-Factor Pluggable Modules

Obtaining Documentation, Obtaining Support, and Security

Guidelines

For information on obtaining documentation, obtaining support, providing documentation feedback,

security guidelines, and also recommended aliases and general Cisco

documents, see the monthly

What’s

New in Cisco Product Documentation, which also lists all new and revised Cisco technical

documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

CHAPTER

2-1

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

2

System Message Overview

This guide describes the Catalyst 3750, 3560, 3550, 2975, 2970, and 2960-specific system messages.

During operation, the system software sends these messages to the console (and, optionally, to a logging

server on another system). Not all system messages indicate problems with your system. Some messages

are purely informational, whereas others can help diagnose problems with communications lines,

internal hardware, or the system software. This guide also includes error messages that appear when the

system fails.

For information about system messages that are not Catalyst 3750, 3560, 3550, 2975, 2970, or 2960

platform-specific, see the Cisco IOS Software System Messages for Cisco IOS Release 12.2S.

This chapter contains these sections:

• How to Read System Messages, page 2-1

• Error Message Traceback Reports, page 2-7

How to Read System Messages

System log messages can contain up to 80 characters and a percent sign (%), which follows the optional

sequence number or time stamp information, if configured. Messages are displayed in this format:

seq no:timestamp: %facility-severity-MNEMONIC:description (hostname-n) (only Catalyst 3750 and

2975 switches)

seq no:timestamp: %facility-severity-MNEMONIC:description (switches other than Catalyst 3750 and

2975 switches)

By default, a switch sends the output from system messages to a logging process. In a switch stack, stack

members append their hostnames to the output from system messages and redirect the output to the

logging process on the stack master.

Each system message begins with a percent sign (%) and is structured as follows:

%FACILITY-SEVERITY-MNEMONIC: Message-text

• FACILITY is a code consisting of two or more uppercase letters that show the facility to which the

message refers. A facility can be a hardware device, a protocol, or a module of the system software.

Table 2-1 lists Catalyst 3750, 3560, 3550, 2975, 2970, and 2960-specific facility codes. These

messages are described in Chapter 3, “Message and Recovery Procedures,” in alphabetical order by

facility code, with the most severe (lowest number) errors described first.

2-2

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Chapter 2 System Message Overview

How to Read System Messages

Ta b l e 2-1 Facility Codes

Facility Code Description Location

ACLMGR ACL manager “ACLMGR Messages” section on page 3-3

AUTOQOS Automatic quality of service

(auto-QoS) (only Catalyst 3550

switches)

“AUTOQOS Messages” section on page 3-8

BACKUP_INTERFACE Flex Links “BACKUP_INTERFACE Messages” section on

page 3-8

BADTRANSCEIVER Defective transceiver messages (only

3750 and 2975 switches)

“BADTRANSCEIVER Messages” section on

page 3-9

BSPATCH Boot loader patch “BSPATCH Messages” section on page 3-9

CFGMGR Configuration manager (only Catalyst

3750 and 2975 switches)

“CFGMGR Messages” section on page 3-10

CMP Cluster Membership Protocol “CMP Messages” section on page 3-13

DHCP_SNOOPING DHCP snooping “DHCP_SNOOPING Messages” section on

page 3-14

DHCP_SNOOPING_CAT3550 DHCP snooping (only Catalyst 3550

switches)

“DHCP_SNOOPING_CAT3550 Messages”

section on page 3-17

DOT1Q_TUNNELLING IEEE 802.1Q tunneling (only

Catalyst 3550 switches)

“DOT1Q_TUNNELLING Messages” section on

page 3-18

DOT1X IEEE 802.1x “DOT1X Messages” section on page 3-18

DOT1X_SWITCH IEEE 802.1x for switches “DOT1X_SWITCH Messages” section on

page 3-19

DTP Dynamic Trunking Protocol “DTP Messages” section on page 3-23

DWL Down-when-looped “DWL Messages” section on page 3-24

EC EtherChannel “EC Messages” section on page 3-25

ENVIRONMENT Environment (only Catalyst 3550

switches)

“ENVIRONMENT Messages” section on

page 3-29

ETHCNTR Ethernet Controller “ETHCNTR Messages” section on page 3-30

EXPRESS_SETUP Express Setup “EXPRESS_SETUP Messages” section on

page 3-34

FM Feature manager (only Catalyst 3550

switches)

“FM Messages” section on page 3-35

FRNTEND_CTRLR Front-end controller (only

Catalyst 3750 and 2975 switches)

“FRNTEND_CTRLR Messages” section on

page 3-44

GBIC Gigabit Interface Converter (GBIC)

module identification and validation

(only Catalyst 3550 switches)

“GBIC Messages” section on page 3-45

GBIC_SECURITY GBIC module and small form-factor

pluggable (SFP) module security

“GBIC_SECURITY Messages” section on

page 3-48

GBIC_SECURITY_CRYPT GBIC and SFP module security “GBIC_SECURITY_CRYPT Messages” section

on page 3-51

2-3

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Chapter 2 System Message Overview

How to Read System Messages

GBIC_SECURITY_UNIQUE GBIC and SFP module security “GBIC_SECURITY_UNIQUE Messages” section

on page 3-52

GIGASTACK GigaStack GBIC module

(Catalyst 3550 switch only)

“GIGASTACK Messages” section on page 3-53

HARDWARE Hardware “HARDWARE Messages” section on page 3-54

HLFM Local forwarding manager “HLFM Messages” section on page 3-56

HPSECURE Port security “HPSECURE Messages” section on page 3-57

IDBMAN Interface description block manager “IDBMAN Messages” section on page 3-58

IGMP_QUERIER Internet Group Management Protocol

(IGMP) querier

“IGMP_QUERIER Messages” section on

page 3-61

ILPOWER Power over Ethernet (PoE) “ILPOWER Messages” section on page 3-62

IMAGEMGR Image manager (only Catalyst 3750

and 2975 switches)

“IMAGEMGR Messages” section on page 3-69

IP_DEVICE_TRACKING_HA IP device tracking for high availability “IP_DEVICE_TRACKING_HA Messages”

section on page 3-70

L2TM Layer 2 forwarding manager

(only Catalyst 3550 switches)

“L2TM Messages” section on page 3-71

L3TCAM Layer 3 unicast routing manager

(only Catalyst 3550 switches)

“L3TCAM Messages” section on page 3-71

MAC_LIMIT MAC address table entries “MAC_LIMIT Messages” section on page 3-72

MAC_MOVE Host activity “MAC_MOVE Messages” section on page 3-73

NETWORK_PORT_

SATELLITE

Network port satellite (only Catalyst

3550 switches)

“NETWORK_PORT_SATELLITE Messages”

section on page 3-73

PAGP_DUAL_ACTIVE Port Aggregation Protocol (PAgP)

dual-active detection

“PAGP_DUAL_ACTIVE Messages” section on

page 3-74

PBR Policy-based routing (PBR)

(only Catalyst 3550 switches)

“PBR Messages” section on page 3-75

PHY PHY “PHY Messages” section on page 3-77

PIMSN Protocol Independent Multicast (PIM)

snooping

“PIMSN Messages” section on page 3-79

PLATFORM Low-level platform-specific “PLATFORM Messages” section on page 3-80

PLATFORM_FBM Platform fallback bridging manager “PLATFORM_FBM Messages” section on

page 3-81

PLATFORM_HPLM Platform pseudo label manager “PLATFORM_HPLM Messages” section on

page 3-83

PLATFORM_IPC Platform inter-process communication

protocol (only Catalyst 3750 and 2975

switches)

“PLATFORM _IPC Messages” section on

page 3-84

PLATFORM_PBR Platform policy-based routing “PLATFORM_PBR Messages” section on

page 3-86

Table 2-1 Facility Codes (continued)

Facility Code Description Location

2-4

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Chapter 2 System Message Overview

How to Read System Messages

PLATFORM_PM Platform port manager “PLATFORM_PM Messages” section on

page 3-88

PLATFORM_RPC Platform remote procedure call (only

Catalyst 3750 and 2975 switches)

“PLATFORM_RPC Messages” section on

page 3-89

PLATFORM_SPAN Platform Switched Port Analyzer “PLATFORM_SPAN Messages” section on

page 3-91

PLATFORM_UCAST Platform unicast routing “PLATFORM_UCAST Messages” section on

page 3-92

PLATFORM_VLAN Platform VLAN “PLATFORM_VLAN Messages” section on

page 3-95

PLATFORM_WCCP Platform WCCP “PLATFORM_WCCP Messages” section on

page 3-96

PM Port manager “PM Messages” section on page 3-97

PORT_SECURITY Port security “PORT_SECURITY Messages” section on

page 3-105

QATM QoS and ACL TCAM manager (only

Catalyst 3550 switches)

“QATM Messages” section on page 3-107

QM QoS manager (only Catalyst 3550

switches)

“QM Messages” section on page 3-108

QOSMGR QoS manager “QOSMGR Messages” section on page 3-111

RMON Remote Network Monitoring (RMON) “RMON Messages” section on page 3-117

SDM Switch Database Manager

(only Catalyst 3750 switches)

“SDM Messages” section on page 3-118

SPAN Switched Port Analyzer “SPAN Messages” section on page 3-118

SPANTREE Spanning Tree “SPANTREE Messages” section on page 3-119

SPANTREE_FAST Spanning-tree fast convergence “SPANTREE_FAST Messages” section on

page 3-127

SPANTREE_VLAN_SW Spanning-tree VLAN switch “SPANTREE_VLAN_SW Messages” section on

page 3-127

STACKMGR Stack manager (only Catalyst 3750 and

2975 switches)

“STACKMGR Messages” section on page 3-127

STORM_CONTROL Storm control “STORM_CONTROL Messages” section on

page 3-130

SUPERVISOR Supervisor ASIC “SUPERVISOR Messages” section on page 3-131

SUPQ Supervisor queue “SUPQ Messages” section on page 3-131

SW_DAI Dynamic ARP inspection “SW_DAI Messages” section on page 3-133

SW_MACAUTH MAC address authentication (only

Catalyst 3750 and 3560 switches)

“SW_MACAUTH Messages” section on

page 3-136

SW_VLAN VLAN manager “SW_VLAN Messages” section on page 3-137

Table 2-1 Facility Codes (continued)

Facility Code Description Location

2-5

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Chapter 2 System Message Overview

How to Read System Messages

• SEVERITY is a single-digit code from 0 to 7 that reflects the severity of the condition. The lower

the number, the more serious the situation.

Table 2-2 lists the message severity levels.

• MNEMONIC is a code that uniquely identifies the message.

• Message-text is a text string describing the condition. This portion of the message sometimes

contains detailed information about the event, including terminal port numbers, network addresses,

or addresses that correspond to locations in the system memory address space. Because the

information in these variable fields changes from message to message, it is represented here by short

strings enclosed in square brackets ([ ]). A decimal number, for example, is represented as [dec].

Table 2-3 lists the variable fields in messages.

SW_MATM Mac address table manager (only

Catalyst 3550 switches)

“SW_MATM Messages” section on page 137

SWITCH_QOS_TB QoS trusted boundary “SWITCH_QOS_TB Messages” section on

page 3-145

TCAMMGR Ternary content addressable memory

manager

“TCAMMGR Messages” section on page 3-145

UDLD UniDirectional Link Detection “UDLD Messages” section on page 3-147

UFAST_MCAST_SW UplinkFast packet transmission “UFAST_MCAST_SW Messages” section on

page 3-149

VQPCLIENT VLAN Query Protocol client “VQPCLIENT Messages” section on page 3-150

WCCP Web Cache Communication Protocol

(WCCP)

“WCCP Messages” section on page 151

WRLSCNTR Messages Catalyst 3750 Integrated Wireless LAN

Controller switch

“WRLSCNTR Messages” section on page 3-151

Table 2-1 Facility Codes (continued)

Facility Code Description Location

Ta b l e 2-2 Message Severity Levels

Severity Level Description

0 – emergency System is unusable.

1 – alert Immediate action required.

2 – critical Critical condition.

3 – error Error condition.

4 – warning Warning condition.

5 – notification Normal but significant condition.

6 – informational Informational message only.

7 – debugging Message that appears during debugging only.

2-6

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Chapter 2 System Message Overview

How to Read System Messages

All syslog messages generated by a Catalyst 3750 and 2975 switch other than the master switch are

displayed ending with (Switch-x) where Switch-x is the number of the stack member generating the

message. Syslog messages generated by the master switch are displayed with no hostname string.

This example shows a partial switch system message on a switch other than a Catalyst 3750 and

2975 switch:

00:00:46: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up

00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up

00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to up

00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down

00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed

state to down 2 *Mar 1 18:46:11: %SYS-5-CONFIG_I: Configured from console by vty2

(10.34.195.36)

18:47:02: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)

*Mar 1 18:48:50.483 UTC: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)

This example shows a partial switch system message for a stack master and a stack member switch

(hostname Switch-2) in a Catalyst 3750 switch stack or a Catalyst 2975 switch stack:

00:00:46: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up

00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to up

00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up

00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down

00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed

state to down 2

*Mar 1 18:46:11: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)

18:47:02: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)

*Mar 1 18:48:50.483 UTC: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)

00:00:46: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up (Switch-2)

00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/1, changed state to up (Switch-2)

00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up (Switch-2)

00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down

(Switch-2)

00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/1, changed

state to down 2 (Switch-2)

Ta b l e 2-3 Representation of Variable Fields in Messages

Representation Type of Information

[dec] Decimal integer

[char] Single character

[chars] Character string

[enet] Ethernet address (for example, 0000.FEED.00C0)

[hex] Hexadecimal integer

[inet] Internet address

2-7

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Chapter 2 System Message Overview

Error Message Traceback Reports

Some messages describe internal errors and contain traceback information. This information is very

important and should be included when you report a problem to your technical support representative.

This message example includes traceback information:

-Process= "Exec", level= 0, pid= 17

-Traceback= 1A82 1AB4 6378 A072 1054 1860

Some system messages ask you to copy the error messages and take further action. These online tools

also provide more information about system error messages.

Output Interpreter

The Output Interpreter provides additional information and suggested fixes based on the output of many

CLI commands, such as the the show tech-support privileged EXEC command. You can access the

Output Interpreter at this URL:

https://www.cisco.com/cgi-bin/Support/OutputInterpreter/home.pl

Bug Toolkit

The Bug Toolkit provides information on open and closed caveats, and allows you to search for all

known bugs in a specific Cisco IOS Release. You can access the Bug Toolkit at this URL:

http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl

Contacting TAC

If you cannot determine the nature of the error, see the “Obtaining Documentation, Obtaining Support,

and Security Guidelines” section on page x for further information.

2-8

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Chapter 2 System Message Overview

Error Message Traceback Reports

CHAPTER

3-1

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

3

Message and Recovery Procedures

This chapter describes the Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 switch system messages in

alphabetical order by facility. Within each facility, the messages are listed by severity levels 0 to 7: 0 is

the highest severity level, and 7 is the lowest severity level. Each message is followed by an explanation

and a recommended action.

The messages listed in this chapter do not include the hostname or the date/time stamp designation that

displays only if the software is configured for system log messaging.

The chapter includes these message facilities:

• ACLMGR Messages, page 3-3

• AUTOQOS Messages, page 3-8 (only Catalyst 3550 switches)

• BACKUP_INTERFACE Messages, page 3-8

• BADTRANSCEIVER Messages, page 3-9 (only Catalyst 3750 and 2975 switches)

• BSPATCH Messages, page 3-9

• CFGMGR Messages, page 3-10 (only Catalyst 3750 and 2975 switches)

• CMP Messages, page 3-13

• DHCP_SNOOPING Messages, page 3-14

• DHCP_SNOOPING_CAT3550 Messages, page 3-17 (only Catalyst 3550 switches)

• DOT1Q_TUNNELLING Messages, page 3-18 (only Catalyst 3550 switches)

• DOT1X Messages, page 3-18

• DOT1X_SWITCH Messages, page 3-19

• DTP Messages, page 3-23

• DWL Messages, page 3-24

• EC Messages, page 3-25

• ENVIRONMENT Messages, page 3-29 (only Catalyst 3550 switches)

• ETHCNTR Messages, page 3-30

• EXPRESS_SETUP Messages, page 3-34

• FM Messages, page 3-35 (only Catalyst 3550 switches)

• FRNTEND_CTRLR Messages, page 3-44 (only Catalyst 3750 and 2975 switches)

• GBIC Messages, page 3-45 (only Catalyst 3550 switches)

• GBIC_SECURITY Messages, page 3-48

3-2

Catalyst 3750, 3560, 3550, 2975, 2970, and 2960 Switch System Message Guide

OL-8551-04

Chapter 3 Message and Recovery Procedures

• GBIC_SECURITY_CRYPT Messages, page 3-51

• GBIC_SECURITY_UNIQUE Messages, page 3-52

• GIGASTACK Messages, page 3-53 (only Catalyst 3550 switches)

• HARDWARE Messages, page 3-54

• HLFM Messages, page 3-56

• HPSECURE Messages, page 3-57 (only Catalyst 3750 and 2975 switches)

• IDBMAN Messages, page 3-58

• IGMP_QUERIER Messages, page 3-61

• ILPOWER Messages, page 3-62

• IMAGEMGR Messages, page 3-69 (only Catalyst 3750 and 2975 switches)

• IP_DEVICE_TRACKING_HA Messages, page 3-70

• L2TM Messages, page 3-71 (only Catalyst 3550 switches)

• L3TCAM Messages, page 3-71 (only Catalyst 3550 switches)

• MAC_LIMIT Messages, page 3-72

• MAC_MOVE Messages, page 3-73

• NETWORK_PORT_SATELLITE Messages, page 3-73 (only Catalyst 3550 switches)

• PAGP_DUAL_ACTIVE Messages, page 3-74

• PBR Messages, page 3-75 (only Catalyst 3550 switches)

• PHY Messages, page 3-77

• PIMSN Messages, page 3-79 (only Catalyst 3750 and 3560 switches)

• PLATFORM Messages, page 3-80

• PLATFORM_HCEF Messages, page 3-82 (only Catalyst 3750 and 3560 switches)

• PLATFORM_HPLM Messages, page 3-83 (only Catalyst 3750 and 3560 switches)

• PLATFORM _IPC Messages, page 3-84 (only Catalyst 3750 and 2975 switches)

• PLATFORM_IPv6 Message, page 3-85

• PLATFORM_PBR Messages, page 3-86 (only Catalyst 3750 and 3560 switches)

• PLATFORM_PM Messages, page 3-88

• PLATFORM_RPC Messages, page 3-89 (only Catalyst 3750 and 2975 switches)

• PLATFORM_SPAN Messages, page 3-91 (only Catalyst 3750 and 3560 switches)

• PLATFORM_UCAST Messages, page 3-92 (only Catalyst 3750 and 3560 switches)

• PLATFORM_VLAN Messages, page 3-95

• PLATFORM_WCCP Messages, page 3-96 (only Catalyst 3750 and 3560 switches)

• PM Messages, page 3-97

• PORT_SECURITY Messages, page 3-105

• QATM Messages, page 3-107 (only Catalyst 3550 switches)

• QM Messages, page 3-108 (only Catalyst 3550 switches)

• QOSMGR Messages, page 3-111

• RMON Messages, page 3-117

Page is loading ...

Cisco Catalyst 3750V2-48TS Switch User manual

Cisco Catalyst 3750V2-48TS Switch User manual

Related papers

Other documents