Kohler K-6227A User manual

Kohler
Brand
Kohler
Model
K-6227A
Category
Sanitary ware
Type
User manual

Kohler K-6227A Karbon™ Kitchen Sink Tap comes with the following capabilities:

  • Can be installed in sinks without tap holes, requiring a countertop with pre-drilled holes for the tap and remote valve.
  • Features a remote valve that can be placed up to 203 mm away from the spout, allowing for flexible positioning.
  • Has a spout with an aerator to reduce splashing and conserve water.
  • Uses G ½” compression fittings for plumbing connections, ensuring compatibility with standard plumbing systems.
  • Can withstand water pressures ranging from 140 to 860 kPa (20 to 125 psi) and temperatures from 5° to 71° C (40° to 160° F).

Kohler K-6227A Karbon™ Kitchen Sink Tap comes with the following capabilities:

  • Can be installed in sinks without tap holes, requiring a countertop with pre-drilled holes for the tap and remote valve.
  • Features a remote valve that can be placed up to 203 mm away from the spout, allowing for flexible positioning.
  • Has a spout with an aerator to reduce splashing and conserve water.
  • Uses G ½” compression fittings for plumbing connections, ensuring compatibility with standard plumbing systems.
  • Can withstand water pressures ranging from 140 to 860 kPa (20 to 125 psi) and temperatures from 5° to 71° C (40° to 160° F).
1
1109784-A2-A
Installation and User Guide
Karbon™ Kitchen Sink Tap
K-6227A
IMPORTANT
INSTALLER: This product manual is the property of the customer and must
be retained with the product for maintenance and operational
purposes.
2
1109784-A2-A
IMPORTANT INFORMATION
Due to the non-standard diameter of
the remote valve (51 mm), the remote
valve cannot be installed through a
standard 35 mm tap hole in a sink.
Choose a sink without tap holes
then install the tap and remote valve
through the countertop. Refer to the
countertop manufacturer for drilling
of the holes.
1. Make sure that you follow all
the local plumbing and building
regulations in operation.
2. For new installations, install the
tap in the sink before installing
the sink.
3. Before installation, unpack the
tap and inspect for damage.
Remote Valve
Tap
Plumbing Connections
G ½” Compression Fitting
Hot (H) and Cold (C) inlets must be connected to the correct inlet supplies.
Applicable Standards
ASME A112.18.1-2005/CSA B125.1-05; AS/NZS 6400:2005; AS/NZS 3718:2005;
AS/NZS 4020:2005
Recommended Operating Pressures: 140 to 860 kPa (20 to 125 psi).
Rated Operating Temperatures: 5° to 71° C (40° to 160° F).
Tested Hydrostatic Burst Pressure: 3450 kPa (500 psi).
SPECIFICATION
3
1109784-A2-A
1. Locate the remote valve within
203 mm of the spout. Refer to the
countertop manufacturer for drilling
of the holes.
2. Apply silicone sealant to the underside
of the concealing plate.
INSTALLATION
Spout Hole
203 mm Max
Ø 51 mm
Concealing Plate
Valve Hole
Ø 35 mm
4
1109784-A2-A
3. Insert the tap through the mounting
hole.
4. Partially thread the screws into the
ring.
5
1109784-A2-A
5. Fitthebreandmetalwashersonto
the threaded shank
Install the ring leaving approximately
6 mm between the ring and the
countertop.
6. Turn the ring until the screws are to
the front and the back. Tighten the
screws securely and evenly.
6 mm
Ring
Fibre Washer
Metal Washer
6
1109784-A2-A
7. Apply silicone sealant to the underside
of the remote valve.
Install the remote valve through the
hole in the countertop.
8. Before tightening the remote valve,
make sure that the cold water supply
is on the left hand side.
9. Partially thread the screws into the
ring.
Remote Valve
Hot
Cold
On
7
1109784-A2-A
10. Slide the washer onto the remote
valve threaded shank. Install the ring
leaving approximately 6 mm between
the ring and the countertop.
11. Turn the ring until the screws are to
the front and the back. Tighten the
screws securely and evenly.
Countertop
Ring
Washer
Ring
6 mm
8
1109784-A2-A
12. Connect the inlet hose to the spout
connection.
13. Connect and tighten the supply
hoses.
Note! If the sink installation requires
that you coil the supply hoses,
maintain a 76 mm diameter inside
the coil.
14. Check for leaks.
Ø 76 mm Min
Spout Connection
Inlet Hose
Hot
Cold
9
1109784-A2-A
15. Remove the aerator.
16. Flush the lines.
17. Reinstall the aerator.
Key
Key
10
1109784-A2-A
SPARE PARTS
Tube
1071689**
1090945**
Spring
1090943
1095310
1031978
58946
1031977
22352
1090946**
Spout
1088910
1088910
Adapter
1090944
Base
1090949**
1021051
Key
1088913
Aerator
1090942
1090941
**Finish/color code must be specified when ordering
Setscrew
Check Valve
1109796
Valve
1090948
Handle
1071700**
Spring
1054201
Bearing
1071703
1071701
Setscrew
1088909
1054197**
Disk
1071702**
1018336**
Concealing Plate
1071704**
O-Ring
77950
Washer
1071706
Screw
58946
1071707
Friction Cup
Threaded Ring
Ball Joint
Tube
Sprayhead
Valve Body
w/Hoses
O-Ring
42043
Shank
1031961
Mounting Nut
1088909
Screw
Threaded Ring
Washer
Washer
O-Ring
O-Ring
Check Valve
11
1109784-A2-A
DIMENSIONS
All dimensions in mm
52 mm
110 mm
2"
1-1/4"
64 mm
64 mm
Max
Ø 67 mm
Ø 67 mm
102 mm
227 mm
590 mm
176 mm
203 mm
Max
337 mm Max
12
1109784-A2-A Kohler Mira Limited, December 2008
CUSTOMER CARE
Kohler Co. warrants its tapware manufactured after January 1, 2006, to be leak and drip free during normal
residential use for as long as the original consumer purchaser owns his/her home. *If the tapware should
leak or drip during normal use, Kohler will, free of charge, mail to the purchaser the cartridge necessary
to put the tapware in good working condition.
Kohler also warrants all other aspects of the tapware, to be free of defects in material and workmanship
during normal residential use for as long as the original consumer purchaser owns his/her own home. If a
defect is found in normal residential use, Kohler Co. will, at its election, repair, provide a replacement part
or product, or make appropriate adjustment. Damage to a product caused by accident, misuse, or abuse
is not covered by this warranty. Proof of purchase (original sales receipt) must be provided to Kohler with
all warranty claims. Kohler Co. is not responsible for labour charges, installation, or other consequential
costs. In no event shall the liability of Kohler exceed the purchase price of the tapware.
If the tapware is used commercially, Kohler warrants the tapware to be free from defects in material and
workmanship for one (1) year from the date the product is installed, with all other terms of this warranty
applying except duration.
If you believe that you have a warranty claim, contact Kohler Co., either through your plumbing supplies
retailer, or by writing.
Australian residents please contact: Kohler Co., Attn.: Customer Service Department,
PO Box 257, Regents Park, NSW 2143.
New Zealand residents please contact Kohler Co., Attn.: Customer Service Department,
133DianaDrive,Gleneld,Auckland.
Please be sure to provide all pertinent information regarding your claim, including a complete description
of the problem, the product, model number, colour, the date the product was purchased and from whom
the product was purchased. Also include your original invoice. For other information, or to obtain the
name and address of the service and repair facility nearest you, call 1300 362 284 from within Australia
or (09) 980 6800 from within New Zealand.
The foregoing warranties are in lieu of all other warranties, express or implied, including but not limited
totheimpliedwarrantiesofmerchantabilityandtnessforaparticularpurpose.
Seller disclaims any liability for special, incidental or consequential damages.
This warranty is to the original consumer purchaser only, and excludes product damage due to installation
error, product abuse, or product misuse, whether performed by a contractor, service company, or the
consumer. This is our exclusive written warranty.
Likeanythingoflastingquality,Kohlertapwareandttingsrequireacertainamountofperiodiccareto
preservetheirlustrousnish.CleanyournewKohlertapwareandttingswithamildsoap,rinsethoroughly
with warm water and dry with a clean, soft cloth. The ideal cleaning technique is to always blot dry any
water from metal surfaces.
Allowing water to evaporate on metal will form water deposits. It is important to use a dabbing action to
dry metal, not an abrasive or rubbing action.
Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, or chemicals that can damage
thenish.Bytakingthetimetodryyourtapwareoften,soapandwaterdepositscanbeprevented.
Failure to comply with these cleaning instructions may void Kohler’s warranty obligations.
CARE AND CLEANING
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Kohler K-6227A User manual

Kohler
Brand
Kohler
Model
K-6227A
Category
Sanitary ware
Type
User manual

Kohler K-6227A Karbon™ Kitchen Sink Tap comes with the following capabilities:

  • Can be installed in sinks without tap holes, requiring a countertop with pre-drilled holes for the tap and remote valve.
  • Features a remote valve that can be placed up to 203 mm away from the spout, allowing for flexible positioning.
  • Has a spout with an aerator to reduce splashing and conserve water.
  • Uses G ½” compression fittings for plumbing connections, ensuring compatibility with standard plumbing systems.
  • Can withstand water pressures ranging from 140 to 860 kPa (20 to 125 psi) and temperatures from 5° to 71° C (40° to 160° F).
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents