Kohler K-6227A User manual

Brand: Kohler

Model: K-6227A

Category: Sanitary ware

Type: User manual

Kohler K-6227A Karbon™ Kitchen Sink Tap comes with the following capabilities:

Can be installed in sinks without tap holes, requiring a countertop with pre-drilled holes for the tap and remote valve.
Features a remote valve that can be placed up to 203 mm away from the spout, allowing for flexible positioning.
Has a spout with an aerator to reduce splashing and conserve water.
Uses G ½” compression fittings for plumbing connections, ensuring compatibility with standard plumbing systems.
Can withstand water pressures ranging from 140 to 860 kPa (20 to 125 psi) and temperatures from 5° to 71° C (40° to 160° F).

Kohler K-6227A Karbon™ Kitchen Sink Tap comes with the following capabilities:

Can be installed in sinks without tap holes, requiring a countertop with pre-drilled holes for the tap and remote valve.
Features a remote valve that can be placed up to 203 mm away from the spout, allowing for flexible positioning.
Has a spout with an aerator to reduce splashing and conserve water.
Uses G ½” compression fittings for plumbing connections, ensuring compatibility with standard plumbing systems.
Can withstand water pressures ranging from 140 to 860 kPa (20 to 125 psi) and temperatures from 5° to 71° C (40° to 160° F).

1109784-A2-A

Installation and User Guide

Karbon™ Kitchen Sink Tap

K-6227A

IMPORTANT

INSTALLER: This product manual is the property of the customer and must

be retained with the product for maintenance and operational

purposes.

1109784-A2-A

IMPORTANT INFORMATION

Due to the non-standard diameter of

the remote valve (51 mm), the remote

valve cannot be installed through a

standard 35 mm tap hole in a sink.

Choose a sink without tap holes

then install the tap and remote valve

through the countertop. Refer to the

countertop manufacturer for drilling

of the holes.

1. Make sure that you follow all

the local plumbing and building

regulations in operation.

2. For new installations, install the

tap in the sink before installing

the sink.

3. Before installation, unpack the

tap and inspect for damage.

Remote Valve

Tap

Plumbing Connections

G ½” Compression Fitting

Hot (H) and Cold (C) inlets must be connected to the correct inlet supplies.

Applicable Standards

ASME A112.18.1-2005/CSA B125.1-05; AS/NZS 6400:2005; AS/NZS 3718:2005;

AS/NZS 4020:2005

Recommended Operating Pressures: 140 to 860 kPa (20 to 125 psi).

Rated Operating Temperatures: 5° to 71° C (40° to 160° F).

Tested Hydrostatic Burst Pressure: 3450 kPa (500 psi).

SPECIFICATION

1109784-A2-A

1. Locate the remote valve within

203 mm of the spout. Refer to the

countertop manufacturer for drilling

of the holes.

2. Apply silicone sealant to the underside

of the concealing plate.

INSTALLATION

Spout Hole

203 mm Max

Ø 51 mm

Concealing Plate

Valve Hole

Ø 35 mm

1109784-A2-A

3. Insert the tap through the mounting

hole.

4. Partially thread the screws into the

ring.

1109784-A2-A

5. Fitthebreandmetalwashersonto

the threaded shank

Install the ring leaving approximately

6 mm between the ring and the

countertop.

6. Turn the ring until the screws are to

the front and the back. Tighten the

screws securely and evenly.

6 mm

Ring

Fibre Washer

Metal Washer

1109784-A2-A

7. Apply silicone sealant to the underside

of the remote valve.

Install the remote valve through the

hole in the countertop.

8. Before tightening the remote valve,

make sure that the cold water supply

is on the left hand side.

9. Partially thread the screws into the

ring.

Remote Valve

Hot

Cold

1109784-A2-A

10. Slide the washer onto the remote

valve threaded shank. Install the ring

leaving approximately 6 mm between

the ring and the countertop.

11. Turn the ring until the screws are to

the front and the back. Tighten the

screws securely and evenly.

Countertop

Ring

Washer

Ring

6 mm

1109784-A2-A

12. Connect the inlet hose to the spout

connection.

13. Connect and tighten the supply

hoses.

Note! If the sink installation requires

that you coil the supply hoses,

maintain a 76 mm diameter inside

the coil.

14. Check for leaks.

Ø 76 mm Min

Spout Connection

Inlet Hose

Hot

Cold

1109784-A2-A

15. Remove the aerator.

16. Flush the lines.

17. Reinstall the aerator.

Key

1109784-A2-A

SPARE PARTS

Tube

1071689**

1090945**

Spring

1090943

1095310

1031978

58946

1031977

22352

1090946**

Spout

1088910

Adapter

1090944

Base

1090949**

1021051

Key

1088913

Aerator

1090942

1090941

**Finish/color code must be specified when ordering

Setscrew

Check Valve

1109796

Valve

1090948

Handle

1071700**

Spring

1054201

Bearing

1071703

1071701

Setscrew

1088909

1054197**

Disk

1071702**

1018336**

Concealing Plate

1071704**

O-Ring

77950

Washer

1071706

Screw

58946

1071707

Friction Cup

Threaded Ring

Ball Joint

Tube

Sprayhead

Valve Body

w/Hoses

O-Ring

42043

Shank

1031961

Mounting Nut

1088909

Screw

Threaded Ring

Washer

O-Ring

Check Valve

1109784-A2-A

DIMENSIONS

All dimensions in mm

52 mm

110 mm

1-1/4"

64 mm

Max

Ø 67 mm

102 mm

227 mm

590 mm

176 mm

203 mm

Max

337 mm Max

1109784-A2-A Kohler Mira Limited, December 2008

CUSTOMER CARE

Kohler Co. warrants its tapware manufactured after January 1, 2006, to be leak and drip free during normal

residential use for as long as the original consumer purchaser owns his/her home. *If the tapware should

leak or drip during normal use, Kohler will, free of charge, mail to the purchaser the cartridge necessary

to put the tapware in good working condition.

Kohler also warrants all other aspects of the tapware, to be free of defects in material and workmanship

during normal residential use for as long as the original consumer purchaser owns his/her own home. If a

defect is found in normal residential use, Kohler Co. will, at its election, repair, provide a replacement part

or product, or make appropriate adjustment. Damage to a product caused by accident, misuse, or abuse

is not covered by this warranty. Proof of purchase (original sales receipt) must be provided to Kohler with

all warranty claims. Kohler Co. is not responsible for labour charges, installation, or other consequential

costs. In no event shall the liability of Kohler exceed the purchase price of the tapware.

If the tapware is used commercially, Kohler warrants the tapware to be free from defects in material and

workmanship for one (1) year from the date the product is installed, with all other terms of this warranty

applying except duration.

If you believe that you have a warranty claim, contact Kohler Co., either through your plumbing supplies

retailer, or by writing.

Australian residents please contact: Kohler Co., Attn.: Customer Service Department,

PO Box 257, Regents Park, NSW 2143.

New Zealand residents please contact Kohler Co., Attn.: Customer Service Department,

133DianaDrive,Gleneld,Auckland.

Please be sure to provide all pertinent information regarding your claim, including a complete description

of the problem, the product, model number, colour, the date the product was purchased and from whom

the product was purchased. Also include your original invoice. For other information, or to obtain the

name and address of the service and repair facility nearest you, call 1300 362 284 from within Australia

or (09) 980 6800 from within New Zealand.

The foregoing warranties are in lieu of all other warranties, express or implied, including but not limited

totheimpliedwarrantiesofmerchantabilityandtnessforaparticularpurpose.

Seller disclaims any liability for special, incidental or consequential damages.

This warranty is to the original consumer purchaser only, and excludes product damage due to installation

error, product abuse, or product misuse, whether performed by a contractor, service company, or the

consumer. This is our exclusive written warranty.

Likeanythingoflastingquality,Kohlertapwareandttingsrequireacertainamountofperiodiccareto

preservetheirlustrousnish.CleanyournewKohlertapwareandttingswithamildsoap,rinsethoroughly

with warm water and dry with a clean, soft cloth. The ideal cleaning technique is to always blot dry any

water from metal surfaces.

Allowing water to evaporate on metal will form water deposits. It is important to use a dabbing action to

dry metal, not an abrasive or rubbing action.

Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, or chemicals that can damage

thenish.Bytakingthetimetodryyourtapwareoften,soapandwaterdepositscanbeprevented.

Failure to comply with these cleaning instructions may void Kohler’s warranty obligations.

CARE AND CLEANING

Kohler K-6227A User manual

Brand: Kohler

Model: K-6227A

Category: Sanitary ware

Type: User manual

Kohler K-6227A Karbon™ Kitchen Sink Tap comes with the following capabilities:

Can be installed in sinks without tap holes, requiring a countertop with pre-drilled holes for the tap and remote valve.
Features a remote valve that can be placed up to 203 mm away from the spout, allowing for flexible positioning.
Has a spout with an aerator to reduce splashing and conserve water.
Uses G ½” compression fittings for plumbing connections, ensuring compatibility with standard plumbing systems.
Can withstand water pressures ranging from 140 to 860 kPa (20 to 125 psi) and temperatures from 5° to 71° C (40° to 160° F).

Download PDF

report

Kohler K-6227A User manual

Kohler K-6227A User manual

Related papers

Other documents