Metabo SBE 660 Operating instructions

Brand: Metabo

Model: SBE 660

Category: Power tools

Type: Operating instructions

Operating Instructions........... page

Mode d’emploi ...................... page

Instrucciones de manejo .... página

Instruções de serviço ......... página

Made in Germany

170 26 7930 - 0106

SB 660

SBE 660

SBE 705

SBE 750

SBE 850 Contact

SBE 850 Impuls

SBE 1010

SBE 1010 Plus

SBE Partner Edition

SBE 1010 NAFTA.book Seite 1 Mittwoch, 25. Januar 2006 3:07 15

SBE 660

SB 660

SBE 705

SBE 750

SBE Partner Edition

SBE 850 Contact

SBE 850 Impuls

SBE 1010

SBE 1010 Plus

W 660 660 705 750 850 850 1010

W 380 380 410 440 480 480 610

120V

A 5,8 5,8 7,9 6,2 6,7 6,7 8,0

/min

0-3000 3000 0-3000 0-3000 0-3000 0-3000 0-2600

0-1000 1000 0-1000 0-1000 0-1000 0-1000 0-900

/min

1850 1850 1700 1600 2300 2300 2600

610 610 560 530 760 760 900

ø max.

(in)

(5/8“)

(3/4“)

S max.

/min.

bpm

57000 57000 57000 57000 57000 57000 50000

ø max.

(in)

(3/4“)

(1“)

(1 3/16“)

(1 9/16“)

ø max.

(in)

(5/16“)

(1/2“)

(5/8“)

(in)

1,0-13

(1/32“-

1/2“)

1,5-13

(1/16“-1/2“)

UNF

(in)

1/2“-20

(in)

6,35

(1/4“)

6,35

(1/4“)

6,35

(1/4“)

6,35

(1/4“)

6,35

(1/4“)

6,35

(1/4“)

lbs

2,1

4,6

2,1

4,6

2,3

5,1

2,3

5,1

2,4

5,3

2,4

5,3

2,4

5,3

(in)

(1 11/16“)

Metabowerke GmbH,

Postfach 1229

Metabo-Allee 1

D-72622 Nürtingen

Germany

SBE 1010 NAFTA.book Seite 2 Mittwoch, 25. Januar 2006 3:07 15

SBE Partner Edition

SBE 1010 NAFTA.book Seite 3 Mittwoch, 25. Januar 2006 3:07 15

SBE 1010 Plus

4 G G G G

6 F F G G

8 F E G G

10 E D G G

13 D G G G

16 C E G G

20 G

30 G

40 G

SBE 850 Contact

SBE 850 Impuls

4 G G F F

6 E F F F

8 E E F F

10 D D F F

13 C G F F

16 F F

20 F

30 F

40 F

SBE 1010 NAFTA.book Seite 4 Mittwoch, 25. Januar 2006 3:07 15

ENGLISH

ENG

1 Specified Conditions of Use

2 General Safety Rules

3 Specific Safety Rules

4 Functional Description

5 Special Product Features

6 Assembly, Initial Operation

6.1 Side handle installation

7 Operation / Use

7.1 Depth stop setting

7.2 Switching on/off

7.3 Speed preselection

7.4 Gear selection

7.5 Changing between drilling/impact

drilling

7.6 Selection of direction of rotation

7.7 Tool change with Futuro Top

keyless chuck

7.8 Tool change with Futuro Plus

keyless chuck

7.9 Tool change with geared chuck

7.10 Contact mode

7.11 Impulse mode

7.12 Torque limiter

7.13 Removing the drill chuck

8 Tips and Tricks

9 Maintenance

10 Trouble Shooting

11 Accessories

12 Repairs

13 Protection of the Environment

14 Technical Specifications

The machine is suitable for non-impact drilling into

metal, wood, plastic and similar materials and for

impact drilling into concrete, stone and other such

materials. Furthermore the machine is suitable for

tapping and screw driving (not SB 660).

The user bears sole responsibility for any damage

caused by inappropriate use.

Generally accepted accident prevention

regulations and the enclosed safety information

must be observed.

1 WARNING! Read and understand all

instructions.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious personal

injury.

SAVE THESE INSTRUCTIONS.

2 Work Area

2.1

Keep your work area clean and well lit.

Cluttered benches and dark areas invite accidents.

2.2

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust.

Power tools

create sparks which may ignite the dust or fumes.

2.3

Keep bystanders, children, and visitors

away while operating a power tool.

Distractions

can cause you to lose control.

3 Electrical Safety

3.1

Grounded tools must be plugged into an

outlet properly installed and grounded in

accordance with all codes and ordinances.

Never remove the grounding prong or modify

the plug in any way. Do not use any adapter

plugs. Check with a qualified electrician if you

are in doubt as to whether the outlet is properly

grounded.

If the tools should electrically

malfunction or break down, grounding provides a

low-resistance path to carry electricity away from

the user.

Applicable only to Class I (grounded) tools.

3.2

Double insulated tools are equipped with a

polarized plug (one blade is wider than the

other). This plug will fit in a polarized outlet only

one way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does not fit,

contact a qualified electrician to install a

polarized outlet. Do not change the plug in any

way.

Double insulation eliminates the need for

the three-wire grounded power cord and

grounded power supply system.

Applicable only to Class II (double insulated) tools.

3.3

Avoid body contact with grounded surfaces

such as pipes, radiators, ranges and

Operating Instructions

Dear Customer,

Thank you for the trust you have placed in us by buying a Metabo power tool. Each Metabo power tool

is carefully tested and subject to strict quality controls by Metabo's quality assurance. Nevertheless, the

service life of a power tool depends to a great extent on you. Please observe the information contained

in these instructions and the enclosed documentation. The more carefully you treat your Metabo power

tool, the longer it will provide dependable service.

Contents

1 Specified Conditions of Use

2 General Safety Rules

SBE 1010 NAFTA.book Seite 5 Mittwoch, 25. Januar 2006 3:07 15

ENGLISH

ENG

refrigerators.

There is an increased risk of electric

shock if your body is grounded.

3.4

Don’t expose power tools to rain or wet

conditions.

Water entering a power tool will

increase the risk of electric shock.

3.5

Do not abuse the cord. Never use the cord

to carry the tools or pull the plug from an outlet.

Keep cord away from heat, oil, sharp edges or

moving parts. Replace damaged cords

immediately.

Damaged cords increase the risk of

electric shock.

3.6

When operating a power tool outside, use

an outdoor extension cord marked "W-A" or

"W".

These cords are rated for outdoor use and

reduce the risk of electric shock.

4 Personal Safety

4.1

Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use tool while tired or under the

influence of drugs, alcohol or medication.

moment of inattention when operating power tools

may result in serious personal injury.

4.2

Dress properly. Do not wear loose clothing

or jewelry. Contain long hair. Keep your hair,

clothing and gloves away from moving parts.

Loose clothes, jewelry or long hair can be caught

in moving parts.

4.3

Avoid accidental starting. Be sure switch is

off before plugging in.

Carrying tools with your

finger on the switch or plugging in tools that have

the switch on invites accidents.

4.4

Remove adjusting keys or wrenches before

turning the tool on.

A wrench or a key that is left

attached to a rotating part of the tool may result in

personal injury.

4.5

Do not overreach. Keep proper footing and

balance at all times.

Proper footing and balance

enable better control of the tool in unexpected

situations.

4.6

Use safety equipment. Always wear eye

protection.

Dust mask, non-skid safety shoes,

hard hat or hearing protection must be used for

appropriate conditions.

5. Tool Use and Care

5.1

Use clamps or other practical way to secure

and support the workpiece to a stable platform.

Holding the work by hand or against your body is

unstable and may lead to loss of control.

5.2

Do not force tool. Use the correct tool for

your application.

The correct tool will do the job

better and safer at the rate for which it is designed.

5.3

Do not use tool if switch does not turn it on

or off.

Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

5.4

Disconnect the plug from the power source

before making any adjustments, changing

accessories, or storing the tool.

Such preventive

safety measures reduce the risk of starting the tool

accidentally.

5.5

Store idle tools out of reach of children and

other untrained persons.

Tools are dangerous in

the hands of untrained users.

5.6

Maintain tools with care. Keep cutting tools

sharp and clean.

Properly maintained tools with

sharp cutting edges are less likely to bind and are

easier to control.

5.7

Check for misalignment or binding of

moving parts, breakage of parts, and any other

condition that may affect the tool's operation. If

damaged, have the tool serviced before using.

Many accidents are caused by poorly maintained

tools.

5.8

Use only accessories that are

recommended by the manufacturer for your

model.

Accessories that may be suitable for one

tool may become hazardous when used on

another tool.

6 SERVICE

6.1

Tool service must be performed only by

qualified repair personnel.

Service or

maintenance performed by unqualified personnel

could result in a risk of injury.

6.2

When servicing a tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual.

Use of

unau-thorized parts or failure to follow

Maintenance instructions may create a risk of

electric shock or injury.

Hold tool by insulated gripping surfaces when

performing an operation where the cutting

tools may contact hidden wiring or its own

cord.

Contact with „live“ wires will make exposed

metal parts of the tool „live“ and shock the

operator.

Always wear hearing protection when using

impact drills.

Exposure to noise can cause loss of

hearing.

Use the additional handles supplied with the

tool.

Loss of control over the tool can lead to

injuries.

Before using this power tool, completely read and

understand the enclosed safety information and

the instructions. Keep all enclosed documentation

for future reference, and pass on your power tool

only together with this documentation.

For your own protection and the

protection of your power tool,

observe the passages marked by

this symbol!

3 Specific Safety Rules

SBE 1010 NAFTA.book Seite 6 Mittwoch, 25. Januar 2006 3:07 15

ENGLISH

ENG

Pull the plug out of the plug socket before any

adjustments or servicing are performed.

Take care to avoid gas, electricity, and water

supplies!

Metabo S-automatic safety clutch.(not SBE 1010)

When the safety clutch responds, switch off the

machine immediately!

Avoid unintentional starting: always unlock the

trigger switch if the machine is unplugged or in the

event of a power failure. Not required for drills with

VTC electronics (restart protection).

For safety reasons, always use the side handle

supplied.

Do not grasp the rotating tool!

Remove chips and similar matter only with the

machine at standstill.

Caution with hard screwdriving (driving of screws

with either a metric or an imperial thread into steel).

The head of the screw may rip off or high restoring

torques may be incurred at the handle.

Always hold the tool firmly, ensure you have good

footing and concentrate when working.

Secure small workpieces. Clamp in a vice for

example.

SYMBOLS ON THE TOOL:

.......Class II Construction

V...........volts

A...........amperes

Hz.........hertz

BPM .....beat per minute

..........alternating current

See page 3 (please unfold).

1 Geared chuck *

2 Keyless chuck Futuro Plus *

3 Keyless chuck Futuro Top *

4Depth stop

5 Control knob for gear selection

6 Slide switch for drilling/impact drilling

7 Contact mode indicator *

8 Contact mode on/off switch button *

9 Ribbed knob for impulse mode preselection *

10 Electronic signal indicator *

11 Lock button

12 Speed preselection wheel *

13 Trigger

14 Selector switch for direction of rotation *

15 Drill bit storage *

16 Side handle/Side handle with rubber coating*

* depending on machine type

Metabo S-automatic safety clutch:

(not SBE 1010)

If the insertion tool jams or hooks, the power flow

to the engine will be restricted. Because of the high

power which then arises, always hold the machine

with both hands on the handles, stand safely, and

concentrate on your work.

Auto-stop carbon brushes:

If the brushes are completely worn, the machine

switches off automatically.

With VTC electronics: A LED warns before the

brushes are completely worn.

Restart protection with VTC electronics:

(SBE 1010, SBE 1010 Plus)

The restart protection prevents an unintentional

starting of the machine when being plugged in

again and when power is restored after a power

failure.

Overload protection indicator with VTC

electronics:

(SBE 1010 Plus)

The overload protection indicator warns of an

impending overload.

Metabo impulse mode:

(SBE 850 Impuls)

For effortless turning-out seized screws, even with

damaged screw heads.

For exact centering, without the need for a centre

punching, in tiles, aluminium or other materials.

Electronic torque limiter:

(SBE 850 pulse)

When driving small screws or tapping threads by

means of taps with a small diameter the torque can

be reduced to a value that suits the job to be

performed.

Metabo contact mode:

(SBE 850 Contact)

For intelligent drilling in walls with installed electric

or water lines. As soon as the inserted tool makes

contact with conductive, earthed material or live

supply cables, the machine switches off

immediately.

Before plugging in check to see that the

rated mains voltage and power

frequency, as stated on the name plate,

match with your power supply.

To ensure that the drill chuck is securely

fitted:

After initial drilling (clockwise), use a

screwdriver to firmly tighten the safety

screw inside the drill chuck (if applicable / model-

specific). Caution left-handed thread !

(see Section 7.13.)

4 Functional Description

5 Special Product Features

6 Assembly, Initial Operation

SBE 1010 NAFTA.book Seite 7 Mittwoch, 25. Januar 2006 3:07 15

ENGLISH

ENG

6.1 Side handle installation

For safety reasons, always use the side

handle supplied.

Open the clamping ring by turning the side handle

(16) counter-clockwise. Place the side handle onto

the machine's collar. Insert the depth stop (4).

Tighten the side handle in the required angle

depending on the task at hand.

Hold the power tool only at insulated

housing parts, if there is a possible

hazard of making contact with

concealed electric cables or the supply cable.

Contact with live wires energizes the metal parts of

the housing and can cause electric shock to the

operator.

7.1 Depth stop setting

Loosen the side handle (16). Set depth stop (4) to

the desired drilling depth and retighten the side

handle.

7.2 Switching on/off

To start the machine, press the trigger (13).

The speed can be changed at the trigger

(not SB 660).

Due to the electronic soft start the machine

accelerates continuously up to the pre-selected

speed (SBE 1010, SBE 1010 Plus,

SBE 850 Impuls, SBE 850 Contact).

For continuous operation the trigger can be locked

with the lock button (11). To stop the machine,

press the trigger again.

If switched on continuously, the machine

continues running if it is jerked out of

your hands. Therefore, always hold the

machine with both hands on the handles, stand

safely, and concentrate on your work.

7.3 Speed preselection

(not for SB 660, SBE 1010)

Pre-select the max. speed with the preselection

wheel (12). See page 4 for recommended drilling

speeds.

7.4 Gear selection

Select the desired gear by turning the control knob

(5).

Change gears only with the machine coming to a

complete standstill (start and switch right off

again).

1. gear

(low speed, high torque)

e.g. for screwing twist drilling

2. gear

(high speed) e.g. for twist drilling,

impact drilling

7.5 Changing between twist drilling/impact

drilling

Select desired operating mode by shifting the slide

switch (6) as required.

Twist drilling

Impact drilling

Use high speed for impact drilling. Set control

knob (5) to .

Impact and twist drilling can be done only with a

clockwise direction of rotation.

7.6 Selection of direction of rotation

(not for SB 660)

Do not actuate the rotation selector

switch (14) unless the motor has

completely stopped.

Select direction of rotation:

R = clockwise

L = counter-clockwise

The drill chuck must be firmly screwed

onto the spindle and the safety screw

inside the drill chuck (if applicable /

model-specific) must be firmly tightened with a

screwdriver. (Caution, left-handed thread !) If

rotated counterclockwise (e.g. when screwing)

it could otherwise become loose.

7.7 Tool change with Futuro Top keyless

chuck (3)

Insert tool. Grip the retaining ring (a) firmly and,

with the other hand, turn the sleeve (b) against the

stop. To open the drill chuck grip the retaining ring

7 Operation / Use

SBE 1010 NAFTA.book Seite 8 Mittwoch, 25. Januar 2006 3:07 15

ENGLISH

ENG

(a) firmly and turn sleeve (b) in the opposite

direction.

7.8 Tool change with Futuro Plus keyless

chuck (2)

Insert tool. Grip the retaining ring (a) firmly and,

with the other hand, turn sleeve (b) towards GRIP,

ZU", until the mechanical resistance which can be

felt is overcome.

Caution! The chuck is not yet fully tightened!

Keep turning

(there is a clicking" sound while

turning)

, until further turning is no longer possible

only now

is the tool

securely

tightened.

When using soft bit shanks, it may be necessary to

retighten the chuck after a short period of

operation.

Opening the drill chuck:

Grip the retaining ring (a) firmly and, with the other

hand, turn the sleeve (b) towards AUF, RELEASE".

Note:

The ratchet sound which can possibly be

heard after opening the drill chuck, is functional

and is switched off by a reverse rotation of the

sleeve.

If the tool is fitted very tight:

Unplug. Hold drill chuck with an open end spanner

at the jaw opening and turn sleeve (b) firmly

towards "AUF, RELEASE".

7.9 Tool change with geared chuck (1)

Fitting the tool:

Insert the tool and tighten evenly with chuck key in

all three 3 holes.

Removing the tool:

Open the geared chuck with the chuck key and

remove tool.

7.10 Contact mode

(SBE 850 Contact)

To enable the contact mode press button (8).

If required, e.g. for drilling into steel girders or

steel-reinforced concrete walls, the contact mode

can be disabled by pressing the switch button (8).

The contact mode indicator (7) shows the current

setting:

Green:contact mode enabled.

Red: machine has switched off because contact

was made with conductive, earthed

material or a live supply cable.

Pull machine back and bit out of the hole

immediately. Have possible damage

properly repaired.

Off: contact mode disabled.

7.11 Pulse function

(SBE 850 pulse)

Adjust via the thumbwheel (9).

Pulse function constantly switched On

+ Pulse function Off (for drilling)

Recommended settings for screwdriving, for

example, into wood (soft screwdriving)::

7.12 Torque limiter

(SBE 850 pulse)

Upon attainment of the preselected torque the

motor comes to a standstill. Adjust via the

thumbwheel (9). (positions 1 - 6).

1 Upon attainment of a low torque the motor

comes to a standstill.

6 Upon attainment of a high torque the motor

comes to a standstill.

4,0

4,5

5,0

6,0

8,0

SBE 1010 NAFTA.book Seite 9 Mittwoch, 25. Januar 2006 3:07 15

ENGLISH

ENG

7.13 Removing the drill chuck

Keyless chuck Futuro Top (3)

Remove the chuck with two open end spanners.

Keyless chuck Futuro Plus (2)

Remove locking screw. Caution: left-handed

thread!

Hold machine spindle with an open end spanner.

With a rubber mallet tap lightly on a chucked Allen

key to loosen the chuck.

Geared chuck (1)

Remove locking screw. Caution: left-handed

thread!

Hold machine spindle with an open end spanner.

Loosen chuck by lightly tapping on the inserted

key with a rubber mallet, then remove fully.

When drillling deep holes, pull the drill bit out of the

hole from time to time to clear the stone dust or

chips.

Drill tiles and other brittle materials without impact.

To start drilling without centering, activate the

impulse mode (SBE 850 Impuls).

For screw driving the drill chuck can be removed.

Insert screwdriver bit directly into the spindle's

hexagon socket.

Attach the screwdriver-bit retaining bush to hold

the screwdriver bit.

For tapping (not SB 660), apply a little cutting oil to

the tap. Select a low speed and . Set for

clockwise rotation and tap hole, stop machine and

switch to counter-clockwise rotation to remove

tap.

Keyless chuck cleaning:

After prolonged use hold the chuck vertically, with

the opening down, and fully open and close it

several times. The dust collected falls from the

opening. The application of cleaning spray to the

jaws and jaw openings at regular intervals is

recommended.

If the trigger (13) can not be depressed, check to

see that the rotation selector switch (14) is fully set

to position R or L (not SB 660).

SBE 850 pulse: When the machine is switched on,

if the thumb-wheel (9) is turned from pulse function

to torque control, the machine will switch off

automatically. Switch the machine off and then

back on again.

8 Tips and Tricks

9 Maintenance

10 Trouble Shooting

SBE 1010 NAFTA.book Seite 10 Mittwoch, 25. Januar 2006 3:07 15

ENGLISH

ENG

Electronic signal indicator (10)

Rapid flashing - restart protection

(SBE 1010, SBE 1010 Plus)

When power is restored after a power failure, the

still switched-on machine does not start for safety

reasons. Switch machine off, then on again.

Slow flashing - carbon brushes worn

(SBE 1010, SBE 1010 Plus)

The carbon brushes are almost completely worn.

If the brushes are completely worn, the machine

switches off automatically. Have the brushes

replaced by an authorized service centre.

Permanently lit - overload

(SBE 1010 Plus)

In the event of prolonged overloading of the

machine, the power input is limited to prevent a

further inadmissible temperature rise of the motor.

Let machine cool down by letting it run at high

speed under no load.

Use only genuine Metabo accessories.

If you need accessories, check with your dealer.

For the dealer to select the correct accessory, he

needs to know the exact model designation of

your power tool.

See page 4.

A Metabox

B Angle Drilling and Screwdriving Attachment

C Flexible Shaft

D Rubber Backing Pad

E Linen-backed Sanding Discs

F Drill Stand

(drill clamp can be rotated by 360°.)

G Moulding & Drill Stand

(Column with toothed rack and guide groove)

H Machine Vice

I Steel-wire End Brush

J Steel-wire Cup Brush

K Steel-wire Wheel Brush

Fitting bit spring

For complete range of accessories, see

www.metabo.com or the main catalogue.

Repairs to power tools must be carried out by

qualified electricians ONLY!

Any Metabo power tool in need of repair can be

sent to one of the addresses listed on the page

before the last page.

Please attach a description of the fault to the

machine.

Metabo's packaging can be 100% recycled.

Worn out power tools and accessories contain

considerable amounts of valuable raw and plastic

materials, which can be recycled.

These instructions are printed on chlorine-free

bleached paper.

Explanatory notes on the information on page 2.

Changes due to technological progress reserved.

=rated input

=rated output

*1 = no-load speed

*1 = load speed

ø max = max. solid drill diameter

S max = max. impact rate

b = drill chuck clamping capacity

G = spindle thread

H = spindle with hexagon socket

m = weight

D = spindle collar diameter

During operation the noise level can exceed

85 dB(A).

Wear hearing protection!

*1 Impuls and Contact models:

High-energy high-frequency interferences can

cause deviations in working speed of up to 20%.

The speed returns to normal as soon as the

interference has faded away.

The technical specifications quoted are subject to

tolerances (in compliance with the relevant valid

standards).

11 Accessories

12 Repairs

13 Protection of the

Environment

14 Technical Specifications

SBE 1010 NAFTA.book Seite 11 Mittwoch, 25. Januar 2006 3:07 15

Page is loading ...

Metabowerke GmbH,

72622 Nürtingen, Germany

www.metabo.com

SBE 1010 NAFTA.book Seite 36 Mittwoch, 25. Januar 2006 3:07 15

Metabo SBE 660 Operating instructions

Brand: Metabo

Model: SBE 660

Category: Power tools

Type: Operating instructions

Download PDF

report

in other languages

français: Metabo SBE 660 Mode d'emploi
español: Metabo SBE 660 Instrucciones de operación
português: Metabo SBE 660 Instruções de operação

Metabo SBE 660 Operating instructions

Metabo SBE 660 Operating instructions

in other languages

Related papers

Other documents