1x Canopy
1x Crossbar
1x Drop
1x Discus Vine 6
2x Nipple
2x Crossbar screw
1x LED Driver Slip ring, set screw, & hex key
1x Ground wire
Discus Vine 6
Installation Guide
Included for installation:
+1 212 343 2600 mattermade.us [email protected]
1x Hex nut & lock washer 5x Wire nut
Caution: Turn o power at the circuit
breaker before beginning installation. Matter
Made recommends the Discus Vine 8 be
installed by a qualified electrician.
Carefully remove the Discus Vine 8 from the
packaging and lay flat on a protected surface.
Attach the threaded nipple (A) into the top of
the fixture.
1.Step 1.
+1 212 343 2600 mattermade.us [email protected]
Feed the wires of the fixture through the drop
(B) and attach the drop to the nipple at the
top of the fixture.
2.Step 2.
Discus Vine 6
Installation Guide
+1 212 343 2600 mattermade.us [email protected]
Slide the slip ring (C) over the drop and tighten
the set screw using the hex key (D). Slide the
canopy over the drop and rest it on the slip
ring.
3.Step 3.
Step 4. Attach the nipple (E) to the top of the drop.4.
Discus Vine 6
Installation Guide
+1 212 343 2600 mattermade.us [email protected]
Attach the crossbar (F), lock washer (G), and
hex nut (H) to the nipple on the top of the
drop. Tighten the hex nut with a wrench.
5.Step 5.
Step 6. Lift the fixture toward the ceiling. Insert the
crossbar screws (I) through the crossbar slots
and attach the crossbar to the junction box.
6.
Discus Vine 6
Installation Guide
+1 212 343 2600 mattermade.us [email protected]
Using the provided wire nuts, connect the following pairs of wires from the junction box to the driver:
- Connect the AC live wire from the junction box to the AC live wire of the driver (J)
- Connect the AC neutral wire from the junction box to the AC live wire of the driver (J)
- Connect the red wire (Vo+) from the fixture to the red wire (Vo+) of the driver (K)
- Connect the black wire (Vo-) from the fixture to the black wire (Vo-) of the driver (K)
- Connect the DIM+ wire from the junction box to the DIM+ wire of the driver (L)
- Connect the DIM- wire from the junction box to the DIM- wire of the driver (L)
- Connect the ground wire from the junction box to the bare copper wire attached to the crossbar (M)
Step 7.
Discus Vine 6
Installation Guide
+1 212 343 2600 mattermade.us [email protected]
8.Step 8. Lift the canopy toward the ceiling and carefully
tuck the wires and driver into the canopy. Using
the hex key (N), loosen the slip ring set screw
(O) and raise the slip ring towards the canopy.
Retighten the set screw to secure the slip ring
and canopy.
Discus Vine 6
Installation Guide
+1 212 343 2600 mattermade.us [email protected]
Locate the arm (P) pictured below left. Rotate
the arm to the horizontal position.
9.Step 9.
Discus Vine 6
Installation Guide
+1 212 343 2600 mattermade.us [email protected]
10.Step 10. Using the hex key (Q), remove the set screw
(R) from the arm. Align the hole in the arm
with the hole in the internal hardware. Reinsert
the set screw and tighten until the set screw is
flush with the arm.
Discus Vine 6
Installation Guide
+1 212 343 2600 mattermade.us [email protected]
Turn on the power and test switch and
dimming function. Installation is now
complete.
Enjoy!
11 .Step 11.
Discus Vine 6
Installation Guide
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
MATTER MADE Discus Vine 8 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Gill MAXIMUS DOUBLE RING HAMMER CAGE Operating instructions
-
-
-
Pirelli Wireless-VoIP-AG-v1 Owner's manual
-
-
Pirelli DRG-A225G User manual
-
Disc Makers Micro Print User manual
-
-
-