Bancroft BNC1028-001 Magic Vee V5 Micro 225mm 8.9″ Racing Boat User manual

  • Hello! I've reviewed the instruction manual for the Bancroft Magic Vee V5 and Magic Cat V5 2.4HGz RTR racing boats. This document details how to set up, operate, and maintain your new boat, including battery charging procedures, transmitter binding, and maintenance tips. I'm ready to answer any questions you have about your device.
  • What type of battery does the transmitter use?
    How long does it take to charge the 6.4V LiFePo battery?
    How long does a fully charged battery last?
    What should I do if the boat takes on water?
ATTENTION:
Before racing your model boat, carefully check silicone tube for guarantee good water cooling system; Avoid
water inlet on the bottom of hull become deformed, otherwise, water cooling system failure, this may lead to
ESC burned out and motor defected.
MAGIC VEE V5 2.4HGz RTR
SKU #BNC1028-001
MAGIC CAT V5 2.4HGz RTR
SKU #BNC1029-001
Allen Key (Only for Magic Vee Turn Fins)
8) Spare Silicone Coupler
Magic Vee V5 Racing Boat
Magic Cat V5 Racing Boat
6.4V 320mAh LiFePo4 Battery
6.4V USB Charger and USB DC Adapter
The Magic Series are designed for use in fresh water only. They are not designed for use in salt water!
The Magic Series is not intended for persons under 14 years of age,unless closely supervised by an adult.
Magic Vee V5/Cat V5 RTR Micro EP Speed Boat
Magic Vee V5 and Magic Cat V5 are compatible with this manual.
2
1) Ensure transmitter ‘ON/OFF’ switch is in the
‘OFF’ position.
2) Remove battery cover screw.
3) Remove battery cover by pressing down on
the embossed arrow and sliding the cover as
indicated.
4) Insert 9V battery, noting correct location
(polarity + or -).
5) Slide battery cover back into place.
6) Re-fit battery cover screw.
NOTE 1: The Magic Series are supplied with a
start-up 9V dry cell battery. Once this battery
is depleted, please replace it with another dry
cell 9V battery (alkaline recommended) or fully
charged 9V rechargeable battery. Remove 9V
battery from the transmitter if you do not intend
to use it for a period of time.
NOTE 2: When the transmitter battery (dry cell
or rechargeable) is at the end of its life, it should
be disposed of at an approved battery recycling
centre.
CHARGING THE 6.4V POWER PACK
2 6
9V Battery
4
3
5
1‘OFF’
Magic Vee V5/Cat V5 RTR Micro EP Speed Boat
DO NOT DISPOSE OF IT IN HOUSEHOLD
WASTE!
INSTALLING THE 9V BATTERY IN YOUR TRANSMITTER
Always use a fresh 9V battery in the
transmitter.
1) Insert the USB charger into a USB port, or use
the included 12V car adapter if you want to
charge in the field.
2) Plug in the 6.4V LiFePo battery to the charger
cable. An LED light will begin to blink in the
base of the USB plug to indicate that the
battery is charging.
3) A fully discharged battery will take about
80min to fully charge. Do not overcharge.
Do not leave the battery unattended while charging.
4) The blinking LED light will turn solid when the charge is complete. Disconnect the 6.4V LiFePo battery
from the charger.
• The 6.4V LiFePo battery does not come pre-charged.
You must fully charge the battery before using the boat
• The 6.4V LiFePo battery can be re-charged many times before it needs to be replaced.
When the battery no longer holds a charge (is dead), it should be properly recycled.
NOTE 1: The boat will typically run for about 8 min on a fully charged battery. As soon as you notice a
drop off in speed, you should bring the model back to shore or you may lose control of the boat.
NOTE 2: Continuous running of the model will generate high heat levels, which will lead to premature
wear on the motor. It is recommended to let the model cool down for about 5-10 min before
installing a re-charged battery pack.
The binding process effectively ties the transmitter and receiver together. Under normal circumstances, both
items are supplied like this from the factory. If, however, you find that your transmitter and receiver are not
bound(receiver’s red LED is on), you should do the following:
1) Switch “ON” the transmitter.
2) Switch “ON” the receiver by Attaching 6.4V power pack’s connector to the matching connector in the
Magic Series boat.
3) Press down the “BIND” button on the receiver, the receiver’s green LED will be on to indicate that binding has
been successful and the receiver will now accept commands from the transmitter.
Note 1: During binding process, transmitter and receiver should be no more than one meter apart and no other
similar devices should be within 10 meters.
Note 2: if the green light flashing, showing the binding failure, please do again as above indication.
TRANSMITTER/RECEIVER BINDING
Insert the 6.4V Power Pack into the left side of
the hull.
3
(Model should be placed on its supplied
boat stand)
1) Remove the Magic Series’s upper deck by
pulling carefully on the catch at its rear section.
2)
3)
4) Re-position the upper deck.
Attach the 6.4V Power Pack’s connector to
the matching connector in the Magic Series. Do
not force them together - they only attach
one way! 2
3
1
4
HOW TO CONTROL/OPERATE YOUR MAGIC SERIES
1) Forward Throttle Trigger
Your Magic Series can be driven forward by
pulling the throttle trigger. Release the
trigger and the Series Vee will stop.
2) Left/Right Steering Wheel
The steering wheel controls the Magic Series’s
left and right movement. Turn the wheel to
the left to steer to the left. Turn the wheel
to the right to steer to the right. Release the
wheel to go straight.
Racing Tip: The Magic Series is an oval racer,
designed for clockwise racing, and will be less
responsive to steering inputs at high speed,
particularly left turns. Decrease your speed to
allow tighter turning.
1
2
Magic Vee V5/Cat V5 RTR Micro EP Speed Boat
NOTE: 1. There is a water proof rubber ring placed along the slot of hull, always make sure it’s secured
positioned before re-position the upper deck.
2. It is suggested that don’t leave the rubber ring in the slot of hull. Remove the rubber ring when
not racing the boat, so as to keep the rubber ring flexible for water proof effective.
INSTALLING THE 6.4 V POWER PACK IN THE MAGIC SERIES
4
DRIVING YOUR MAGIC SERIES
1) Switch ‘ON’ the transmitter. Check that the transmitters red LED glows brightly.
2) Check that the Magic Vee’s turn fins are adjusted correctly.
3) Switch ‘ON’ the Magic Seriess (connect the 6.4V Power Pack).
4) Check that the propeller and the rudder respond to transmitter inputs before placing the Magic Series on the
water.
AFTER USE
1) When you have finished using your Magic Series, you should first switch ‘OFF’ the model (disconnect the 6.4V
Power Pack), then switch ‘OFF’ your transmitter.
2) Remove all batteries from the transmitter and model.
3) Leave the Magic Seriess upper deck off to allow moisture to evaporate. Ideally, place the model in this way in a
warm and dry place, like an airing cupboard, until you are sure it is dry and then store it away.
NOTE: If the Magic Series begins to bob when running, it may have taken on an excessive amount of water. In
this case, you should immediately return to shore, remove the upper deck and drain the water from the hull.
IF YOUR VESSEL DOES NOT OPERATE IN A STRAIGHT LINE
TURN FINS
The Magic Vee features adjustable turn fins
to aid in turning. These can be adjusted using
the included Allen key. The optimum angle of
adjustment is 45 degrees to the hull.
Magic Vee V5/Cat V5 RTR Micro EP Speed Boat
ST.TRIM-L
ST.TRIM-R
If your Magic Series do not run in a
straight line when not being steered, you can adjust
it by using the steering trim located on the upper
right hand side of the transmitter.
1) Run your Magic Series on calm water
when adjusting the steering. If your model runs
to the right when not being steered, press the
“ST.TRIM-L” button. Re-center the model and
see if this has corrected the problem. Keep
making small adjustments in this way until the
model runs stright.
Press the “ST.TRIM-R” button to correct if your
model steers to the left without being steered
in the same way as detailed above.
5
CAUTION!
Please observe the following warnings.
DURING OPERATION
Ensure that all batteries are correctly installed and that the 6.4V Power Pack is fully charged.
Do not touch moving parts during operation, especially the propeller.
If you lose control of your Magic Series, never wade into deep water or water with strong currents to retrieve it.
First, hold the transmitter as high as you can to try to re-establish control. If this does not work, find another
way to move closer to the model, but do not endanger yourself in the process!
CAREFUL HANDLING OF BATTERY (POWER PACK) REQUIRED
Care must be taken when handling rechargeable batteries (the Power Pack) to avoid the possibility of injury
and/or damage to property. Do not short circuit, disassemble or incinerate rechargeable batteries. It is very
dangerous to disregard these warnings.
GENERAL INFORMATION FOR THE SAFE OPERATION OF YOUR MAGIC SERIES
Please follow these simple rules to ensure safe operation and gain the maximum enjoyment from your
model.
Avoid overloading your model. Never run it in areas where its movement will be restricted, e.g. areas where
there is pond weed, etc., as this can over stress the motor.
Ensure nothing prevents the smooth running of moving parts.
Do not run your model in confined spaces.
Never run your model in a public space where it might upset or endanger people or wildlife.
Immediately switch ‘OFF’ your model and transmitter if you see lightning or hear thunder. Never use your
model in the rain.
Do not dismantle or tamper in any way with this R/C vehicle and its transmitter. The manufacturer and distributor
will accept no responsibility, expressed or implied, for accidents or injuries caused as a result of disassembly,
modification and/or usage against the Instructions for this product.
Tampering or modification will also invalidate the guarantee.
Series
Magic Vee V5/Cat V5 RTR Micro EP Speed Boat
Silicone
Coupler
NOTE: After several times of pulling the flexshaft out from the
silicone coupler, the silicone coupler might lose flexibility that
make the connection of flexshaft end not good. Once this happens,
It is suggested to replace the silicone coupler with new one, which
is supplied in the kit bag.
2. Lubricate the flexshaft w/ prop shaft with the water proof marinegrease,
reinstall the flexshaft w/ prop shaft in reverse order, be sureto push the
flexshaft end into the silicone coupler for fullly connection.
1. Use one hand to hold the silicone coupler tight, while other hand to pull
the propeller shaft out from the stuffing tube.
MAINTAINING THE DRIVESHAFT
Lubricating the flexshaft is vital to the life of the drivetrain. The lubricant
also acts as a water seal, keeping water from entering the hull through the
stuffing tube. It is recommanded to lubricate the flexshaft, propeller shaft
after every 2 or 3 times of operation.
Check using the chart below before returning your Magic Series for repair as many problems can be easily
solved.
Magic Vee V5/Cat V5 RTR Micro EP Speed Boat
6.4V
PART NO. DESCRIPTION
BNC1028-100
BNC1028-101
BNC1029-101
BNC1029-102
BNC5059-001
BNC5077-001
BNC6000-004
BNC6004-001
BNC6008-003
BNC6024-001
BNC6026-001
BNC7008-001
Bancroft Magic Vee Hatch(White)/Rubber Ring-V5
Bancroft Magic Vee Rudder & Turn Fins
Bancroft Magic Cat Rudder
Bancroft Magic Cat V5 Hatch-Rubber Ring
Bancroft Rudder Driveshaft Coupler 2Pk
Bancroft 3 BLade Propeller (Pk2)
Bancroft 180 Brushed Motor
Bancroft ESC-2.4GHz Receiver-Servo Set
Bancroft J2C81 2.4GHz Transmitter
Bancroft 6.4V 320mAh LiFePo4 w/ (JST connector)
Bancroft 6.4V USB Charger
Bancroft Flex Shaft
TROUBLESHOOTING
To Purchase Spare Parts or for Technical Assistance,Visit www.motionrc.com
or www.motionrc.eu
/