BALDR B0340WST2H2R-V7 User guide

Brand: BALDR

Model: B0340WST2H2R-V7

Type: User guide

BALDR B0340WST2H2R-V7 is a versatile weather station that provides accurate indoor and outdoor temperature and humidity readings. It features a large, easy-to-read LCD display that shows the current weather conditions, as well as the time, date, and day of the week. The outdoor sensor transmits data wirelessly to the main unit, allowing you to monitor the outdoor conditions from the comfort of your home. The weather station also includes a weather forecast function, which provides a general idea of the expected weather conditions for the next 12 to 24 hours.

OUTDOORSENSORQUICKSET‐UPGUIDE

NOTE: Prepare new and high quality alkaline batteries. Do not mix old and new batteries. Heavy

duty or rechargeable batteries are not recommended.

1. POWER UP

Please must follow the bellow steps to power on the device, otherwise outdoor

sensor may not receive readings.

Step 1: Remove the battery door on the back of the display, insert 3 new AAA batteriesinthe

back of the display console (please take note of the battery polarity beforeinsertingthe

batteries).

Step 2: Take out the metal stand inside the battery compartment and screw it into theholeat

the main unit backside. Replace the battery door.

Step 3: Remove the battery door of remote sensor, and set the channel of sensor to CH1,then

insert 2 new AA batteries in the back of the sensor within 3 MINUTES.

2. TROUBLESHOOTING GUIDE

Problem Possible Solution

Outdoor sensor signal

is lost or showing

dashes (‐ ‐) on the

display

1. Resync the unit. Press and hold the "CH/▲” button for 5‐6

seconds to resynchronize. The sensor search icon will flash while

searching and be solid when sensor signal is received. Please wait

several minutes for the sensor to report in or the search icon to

turn off.

2. If you regain connection while the sensor is mounted, great. If

the the synchronization fails, bring the sensor within 10 feet of

the weather station and try the bellow methods:

Note: The display will beep once and all of the LCD segments will light up for few

seconds to verify all segments are operating properly, then display indoor

temperature and humidity immediately.

Note:

Make sure outside sensor and weather station main unit are at the same channel.

Do not touch any buttons until the remote sensor reports in, otherwise the remote

sensor searching will be terminated. When the remote sensor data has been received,

all further settings can be performed.

The display main unit will automatically receive remote sensor signal whensensoris

powered up. The receiving status will last for max 3minutes(signal sensor will

flash), if no signal received within 3 minutes, it will stop receiving, now you can press

and hold the “CH/▲” Button 3 seconds to start receiving outside signal again.

1) Remove the batteries of Sensor, wait 10 seconds. Then press

and hold the "CH/▲” button for 5‐6 seconds, then reinsert the

batteries of sensor. (Please make sure the sensor and display

console have the same channel.)

2) Factory Restart: Firstlyremoveallthebatteriesofsensorand

display console. Then set the channel of Sensor to "CH1".

Reinsert the batteries of display console and press "CH/▲”

button to choose "CH1". Then reinsert the batteries of sensor,

allow the whole set device to sit together for 30 minutes to

establish a strong connection.

3. Make sure both display console and sensor are placed at least

3ft/0.9m away from electronics that may interfere with the

wireless communication, such as computers, TVs, microwaves,

other wireless transmitters or receivers, etc.

4. Make sure the sensor is not transmitting through solid metal or

thick walls. Radio Frequency (RF) Sensors cannot transmit through

metal barriers or thick walls. (Please refer REMOTE SENSOR

INSTALLATION)

Outdoor temperature

and humidity always

keep cycling/how to

exit the CYCLE mode

“” cycle symbol means that weather station enter channels

cycle mode, it will display the values of 3 channels in order every

10 seconds.

Press the "CH/▲”buttontocancelcyclesymbol.

Temperature reads too

high in the daytime

Make sure both the display console and sensor are placed out of

direct sunlight and away from any heat sources or vents.

Indoor and outdoor

temperature and

humidity do not agree

Allow up to two hours for the sensor to stabilize due to signal

filtering. The indoor and outdoor temperature sensor should

agree within 4℉. And indoor and outdoor humidity sensor should

agree within 10%.

Inaccurate weather

forecast

The weather forecast is an estimate or generalization of weather

changes in the next 12 to 24 hours, with an accuracy rate of about

70‐75%. It is simply a tool for projecting weather conditions and is

never to be relied upon as an accurate method to predict weather.

Display console contrast

is weak

Battery is low, replace a new set of batteries.

Incorrect weekday

display

Press and hold “RCC/SET” button to select the correct Year (year

range: 2000‐2099).

If your BALDR weather station still can't be worked well after trying the above

troubleshooting steps, please contact the seller on your order page or email us by

baldrservice@baldr.com, or message us via WhatsApp: +8618664978063 for help.

BALDR B0340WST2H2R-V7 User guide

BALDR B0340WST2H2R-V7 User guide

BALDR B0340WST2H2R-V7 User guide

Other documents