2. BALDR
  3. B0340WST2H2R-V7
B0340WST2H2R-V7

BALDR B0340WST2H2R-V7 User guide

  • Hello! I am an AI chatbot trained to assist you with the BALDR B0340WST2H2R-V7 User guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
OUTDOORSENSORQUICKSET‐UPGUIDE
NOTE: Prepare new and high quality alkaline batteries. Do not mix old and new batteries. Heavy
duty or rechargeable batteries are not recommended.
1. POWER UP
Please must follow the bellow steps to power on the device, otherwise outdoor
sensor may not receive readings.
Step 1: Remove the battery door on the back of the display, insert 3 new AAA batteriesinthe
back of the display console (please take note of the battery polarity beforeinsertingthe
batteries).
Step 2: Take out the metal stand inside the battery compartment and screw it into theholeat
the main unit backside. Replace the battery door.
Step 3: Remove the battery door of remote sensor, and set the channel of sensor to CH1,then
insert 2 new AA batteries in the back of the sensor within 3 MINUTES.
2. TROUBLESHOOTING GUIDE
Problem Possible Solution
Outdoor sensor signal
is lost or showing
dashes (‐ ‐) on the
display
1. Resync the unit. Press and hold the "CH/▲” button for 5‐6
seconds to resynchronize. The sensor search icon will flash while
searching and be solid when sensor signal is received. Please wait
several minutes for the sensor to report in or the search icon to
turn off.
2. If you regain connection while the sensor is mounted, great. If
the the synchronization fails, bring the sensor within 10 feet of
the weather station and try the bellow methods:
Note: The display will beep once and all of the LCD segments will light up for few
seconds to verify all segments are operating properly, then display indoor
temperature and humidity immediately.
Note:
Make sure outside sensor and weather station main unit are at the same channel.
Do not touch any buttons until the remote sensor reports in, otherwise the remote
sensor searching will be terminated. When the remote sensor data has been received,
all further settings can be performed.
The display main unit will automatically receive remote sensor signal whensensoris
powered up. The receiving status will last for max 3minutes(signal sensor will
flash), if no signal received within 3 minutes, it will stop receiving, now you can press
and hold the “CH/▲” Button 3 seconds to start receiving outside signal again.
1) Remove the batteries of Sensor, wait 10 seconds. Then press
and hold the "CH/▲” button for 5‐6 seconds, then reinsert the
batteries of sensor. (Please make sure the sensor and display
console have the same channel.)
2) Factory Restart: Firstlyremoveallthebatteriesofsensorand
display console. Then set the channel of Sensor to "CH1".
Reinsert the batteries of display console and press "CH/▲”
button to choose "CH1". Then reinsert the batteries of sensor,
allow the whole set device to sit together for 30 minutes to
establish a strong connection.
3. Make sure both display console and sensor are placed at least
3ft/0.9m away from electronics that may interfere with the
wireless communication, such as computers, TVs, microwaves,
other wireless transmitters or receivers, etc.
4. Make sure the sensor is not transmitting through solid metal or
thick walls. Radio Frequency (RF) Sensors cannot transmit through
metal barriers or thick walls. (Please refer REMOTE SENSOR
INSTALLATION)
Outdoor temperature
and humidity always
keep cycling/how to
exit the CYCLE mode
“” cycle symbol means that weather station enter channels
cycle mode, it will display the values of 3 channels in order every
10 seconds.
Press the "CH/▲”buttontocancelcyclesymbol.
Temperature reads too
high in the daytime
Make sure both the display console and sensor are placed out of
direct sunlight and away from any heat sources or vents.
Indoor and outdoor
temperature and
humidity do not agree
Allow up to two hours for the sensor to stabilize due to signal
filtering. The indoor and outdoor temperature sensor should
agree within 4℉. And indoor and outdoor humidity sensor should
agree within 10%.
Inaccurate weather
forecast
The weather forecast is an estimate or generalization of weather
changes in the next 12 to 24 hours, with an accuracy rate of about
70‐75%. It is simply a tool for projecting weather conditions and is
never to be relied upon as an accurate method to predict weather.
Display console contrast
is weak
Battery is low, replace a new set of batteries.
Incorrect weekday
display
Press and hold “RCC/SET” button to select the correct Year (year
range: 2000‐2099).
If your BALDR weather station still can't be worked well after trying the above
troubleshooting steps, please contact the seller on your order page or email us by
baldrservice@baldr.com, or message us via WhatsApp: +8618664978063 for help.
/