MULTI NAUTIC 15524 User manual

Brand
MULTI NAUTIC
Model
15524
Type
User manual

MULTI NAUTIC 15524, a flip-up kit for MULTINAUTIC® Tubular Ladders, provides a convenient solution for dock access. It allows you to easily swing your ladder up and down, ensuring safety and ease of use. With the quick-release positioning locking pins, you can securely lock the ladder in the desired position. The kit includes all necessary hardware and detailed instructions for a hassle-free installation.

MULTI NAUTIC 15524, a flip-up kit for MULTINAUTIC® Tubular Ladders, provides a convenient solution for dock access. It allows you to easily swing your ladder up and down, ensuring safety and ease of use. With the quick-release positioning locking pins, you can securely lock the ladder in the desired position. The kit includes all necessary hardware and detailed instructions for a hassle-free installation.

Dec-
king
Dock
PIVOT hole
Base of
the ladder
POSITIONING
hole
POSITIONING
hole
Ladder
Protective
disk
Triangular
base
PIVOT
hole
In order to distribute the pressure on the bolts and thus strengthen the installation of
your ladder, it is recommended to add reinforcements under the decking to distribute
the load on several boards.
If you cannot access the underside of the dock, you can carefully remove a few boards
from the decking to install these reinforcements.
You will need :
>
2x (or 4x) 16" board lengths ;
FLIP-UP KIT
FOR MULTINAUTIC®
TUBULAR LADDER (models 15524, 15513, 15505)
BOX CONTENT
ASSEMBLE - ENJOY - SHARE !
The best Customer Service team is here for you!
1-800-585-1237
[email protected]
REQUIRED MATERIAL
1
If you have any concerns with this product, do not return it to the store. Please contact our Customer Service.
If your ladder is not already equipped with holes for this flip-up system, make sure that
the handrail portion above the dock does not exceed 21 1/4".
Here is how to drill the handrail uprights:
>
Using a 7/16" drill bit, make the PIVOT holes 10 5/8" from the base of the ladder.
>
Drill the POSITIONING holes below the PIVOT hole using your ladder as a guide (in
raised and lowered positions) or by measuring 2 5/8" above and below the PIVOT hole.
decking
base
reinforcement
>
Position the triangular bases at the desired location on the dock using your ladder as
a guide
>
Make sure the bases are parallel and mark the holes
>
Screw the boards under the dock decking
>
Pre-drill the bolt locations through the decking and reinforcement boards using a
cordless drill with an 11/32" drill bit.
INSTALLATION OF REINFORCEMENTS
LADDER COMPATIBILITY
4
>
Connect the steel cables to the small holes on the aluminum bases to avoid losing the
positioning pins.
>
Place a protective disk between the triangular base and the ladder and lightly tighten
the pivot bolt, leaving enough clearance to allow the ladder to swing up and down.
INSTALLATION OF THE LADDER
3
2
direction of the
decking boards reinforcement
board
ladder
For use with other ladder models, read step 4
product
# 15529
picture :
#15529 +
#15524 ladder
Aluminum
triangular base
(2 x)
Quick release
positionning
locking pin
(2 x)
Protective
disk
(2 x)
Pivot pin
with flat washers
(2 x)
1/4" Countersunk
bolt with
nylon nut
(6 x)
REQUIRED TOOLS
>
Tape measure
>
Pencil
>
Cordless drill with:
-
Phillips bit
-
11/32" drill bit
-
Wrench
Optional:
-
7/16" metal drill bit
  • Page 1 1

MULTI NAUTIC 15524 User manual

Brand
MULTI NAUTIC
Model
15524
Type
User manual

MULTI NAUTIC 15524, a flip-up kit for MULTINAUTIC® Tubular Ladders, provides a convenient solution for dock access. It allows you to easily swing your ladder up and down, ensuring safety and ease of use. With the quick-release positioning locking pins, you can securely lock the ladder in the desired position. The kit includes all necessary hardware and detailed instructions for a hassle-free installation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents