KUZCO 601003-LED Installation guide

Brand: KUZCO

Model: 601003-LED

Type: Installation guide

The KUZCO 601003-LED is an LED lamp wall sconce designed for indoor use. It features a modern and stylish design with a metal cover plate and a glass cover. The fixture comes pre-wired with an LED module, eliminating the need for bulbs, and offers long-lasting energy-efficient lighting. It can be dimmed using an Electronic Low Voltage (ELV) dimmer, allowing you to adjust the brightness to suit your preference. Installation requires a qualified electrician, and the instruction manual provides detailed steps to guide you through the process.

The KUZCO 601003-LED is an LED lamp wall sconce designed for indoor use. It features a modern and stylish design with a metal cover plate and a glass cover. The fixture comes pre-wired with an LED module, eliminating the need for bulbs, and offers long-lasting energy-efficient lighting. It can be dimmed using an Electronic Low Voltage (ELV) dimmer, allowing you to adjust the brightness to suit your preference. Installation requires a qualified electrician, and the instruction manual provides detailed steps to guide you through the process.

INSTALLATION SHEET

601003-LED

LED Lamp Wall Sconce

1. Remove the fixture from its original packaging. Remove

the canopy mounting plate from within the canopy and

attach it to the electrical junction box, using the two

screws provided in the hardware package.

2. Push the canopy mounting screw through the center hole

of the metal cover plate, then (2a) feed the electrical

wires, from inside the electrical box, through the second

hole in the metal cover plate. (2b) Push the canopy

mounting screw through the center hole in the back of the

canopy back plate until it is poking through, then (2c) feed

the electrical wires through the second hole in the canopy

back plate. Once this is complete you can (2d) screw on

the mounting nut until tight, and (2e) secure the canopy

back plate using the screws provided in the hardware

package.

3. Attach the canopy to the canopy back plate, which is

attached to the electrical junction box. First attach all

wiring with the provided marrets (white to white “N”, black

to black “L”, ground to ground “G”). Align the holes on the

sides of the canopy to the holes on the canopy back plate.

Once aligned, screw in the four screws provided to secure

the canopy to the back plate.

4. Gently slide the glass cover into place over top of the

canopy, while pushing the screws through the holes in the

glass until the screws are poking through. (4a) Once this is

complete you can screw on the decorative nuts to secure

the glass to the fixture (do not over tighten).

5. You have now completed the installation of your fixture,

please enjoy.

START FROM HERE

▪

▪

▪

▪

▪

▪

Make sure power is completely off at the fuse box.

Have your fixture installed by a qualified licensed

electrician

Prepare everything in clear area.

Wear gloves at all times during this installation.

Read instructions carefully before you start assembly.

Keep this instruction sheet for future reference.

Technical Support: 1-855-855-8926

1.

2.

2b.

2d.

2e.

4.

4a.

2a.

2c.

3.

Please Note:

• All Kuzco LED fixtures come with pre-wired LED

module(s).

• Unless instructed to do so, please do not touch any part

of the LED module(s) as any unnecessary contact with the

module could cause permanent damage.

• For dimming, an ELV (Electronic Low Voltage) dimmer is

required.

19054 28th Avenue Surrey, BC Canada V3Z 6M3

T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196

W: kuzcolighting.com

20181127

1

KUZCO 601003-LED Installation guide

Brand: KUZCO

Model: 601003-LED

Type: Installation guide

The KUZCO 601003-LED is an LED lamp wall sconce designed for indoor use. It features a modern and stylish design with a metal cover plate and a glass cover. The fixture comes pre-wired with an LED module, eliminating the need for bulbs, and offers long-lasting energy-efficient lighting. It can be dimmed using an Electronic Low Voltage (ELV) dimmer, allowing you to adjust the brightness to suit your preference. Installation requires a qualified electrician, and the instruction manual provides detailed steps to guide you through the process.

Download PDF

Related papers

Other documents