Mount-It MI-395 Installation guide

Brand: Mount-It

Model: MI-395

Category: Fireplaces

Type: Installation guide

Mount-It! MI-395 is a fireplace TV mount designed to hold TVs up to 33kg in weight. It features a spring arm that allows for easy height adjustment of the TV, and a pull handle for convenient operation. The mount is compatible with VESA sizes up to 600x400mm and comes with all necessary hardware for installation.

Here are some of the key features and benefits of the Mount-It! MI-395:

Easy height adjustment: The spring arm makes it easy to adjust the height of the TV to the desired position.
Convenient operation: The pull handle allows for easy operation of the mount, making it easy to raise and lower the TV.

Here are some of the key features and benefits of the Mount-It! MI-395:

Easy height adjustment: The spring arm makes it easy to adjust the height of the TV to the desired position.
Convenient operation: The pull handle allows for easy operation of the mount, making it easy to raise and lower the TV.

FIREPLACE TV MOUNT

MI-395

Thank you for choosing Mount-It

COMPATIBLE VESA SIZES

COMPATIBLE WITH

TVs UP TO

Minimum weight: 13kg

Maximum weight: 33kg

Mount-It!

PACKAGE CONTENTS

VESA HARDWARE

WALL MOUNTING HARDWARE

WALL PLATE

VESA BRACKETS

PLASTIC

PLATE

ALLEN WRENCH WRENCH

RATCHET

WRENCH

WALL

TEMPLATE

BUBBLE

LEVEL

RATCHET

BIT

CROSS BAR PULL HANDLE DECORATIVE COVER

SPRING ARM TV BRACKET

Missing Parts? Call us at (855) 925-5668 and we will ship replacement parts free of charge.

CHOKING HAZARD. Package includes small parts.

Not for children under 3 years. Adult supervision is required.

Check carefully to make sure there are no missing or defective parts. Some hardware provided may

not be used. Use the correct wall mounting and TV mounting hardware suitable for your installation.

b. Mounting

Height

a. Mantel

Depth

Attach the Spring Arm (B) and Wall Plate (A) with bolts (4 x I) as shown, using the Allen Wrench (Q) to

tighten securely.

Installing The Spring Arm To The Wallplate

The height of the mount is dependent on the depth of the mantel to ensure the spring arm clears the

mantel when fully lowered.

Determine the proper wall placement using the chart below.

Measure the depth of your mantel and locate the closest measurement in column A that your mantel

depth is Greater Than Or Equal To. The corresponding measurement in column B will show the

minimum required mounting height from the mantel to the bottom of the wall plate.

Note: Installing below the required mounting height for your mantel depth will prevent the mount from

fully clearing the mantel.

Positioning The Mount Over The Fireplace

Placing Washer (J) on the 3 exposed bolts on the Spring Arm (B) attach TV BRACKET (C) as shown

then secure with Washer (K) and Nut (L). Use Wrench (T) to tighten securely.

Installing The TV Bracket To The Spring Arm

Install Plastic Plate (H) to cover the nuts from the previous step inserting Bolt (M) from the opposite side

as shown using a screwdriver to tighten.

Attaching The Plastic Plate To The TV Bracket

Use a stud finder to locate 2 drywall studs and mark the location with a pencil. Using a bubble level to

ensure straightness, hold the Wall Template (U) to the wall at required mounting height determined by

step 3. Mark the center of the template holes which align with the center of each stud.

Use a 3/16" (4.5mm) drill bit to drill pilot holes on the wall with a depth of 2.2" (55mm). Please note,

failure to drill pilot holes may result in the lag bolt heads snapping during installation.

Holding the mount to the wall aligned with the pilot holes install Washer (W-C) and Lag Bolt (W-A) and

tighten securely. Do not overtighten. Overtightening can damage the lag bolts, greatly reducing their

holding power.

NOTE: This step may require assistance of 1 or more persons to hold heavy parts in place.

CAUTION: DO NOT INSTALL ON DRY WALL ALONE. INSTALL MOUNT ON WOOD STUDS. USER

MUST VERIFY THE WALL CAN HOLD THE WEIGHT OF THE TV AND THE TV MOUNT.

WARNING:Tighten screws so that the wall plate is firmly attached, but do not overtighten. Overtightening

can damage screws, greatly reducing their holding power.

Option 1. Wood Studs Installation

HEAVY! You may need

assistance with this step.

Step 1 Step 3

Step 4

Step 2

Using the bubble level (V) to ensure straightness, hold the Wall Template (U) to the wall at the required

mounting height determined by step 3. Identify the 4 outermost holes (located at each corner) and mark

the center of the holes with a pencil.

Use a 3/8" (10mm) drill bit to drill pilot holes on the wall with a depth of 2.4" (60mm). Please note, failure

to drill pilot holes may result in the lag bolt heads snapping during installation, or stone cracking/crumbling.

Never drill into the mortar in between the blocks, make sure that the anchors are seated flush with the

concrete surface.

Carefully clear any dust or debris from inside the drilled holes and insert all 4 Plastic Wall Anchors (W-B).

Holding the mount to the wall aligned with the pilot holes install Washer (W-C) and Lag Bolts (W-A) and

tighten securely. Do not overtighten. Overtightening can damage the lag bolts or the wall, greatly

reducing their holding power.

Option 2. Concrete/brick Installation

HEAVY! You may need

assistance with this step.

Install Decorative Cover (G) as shown over the top and bottom of the wall bracket, covering the now

installed lag bolts.

Attaching The Decorative Plates

WARNING:Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening

can damage screws, greatly reducing their holding power.

Lay your display face down on a soft, flat, or even surface to prevent damage, and place the VESA Bracket

(D) over the bolt holes on the rear of the TV so that the VESA Brackets (D) are aligned with one another and

not hanging over the top or bottom of the screen. Select the appropriate size mounting bolt for your display’s

mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt

size for your display refer to your TV user manual or contact the TV manufacturer for sizing information. If

necessary use the included spacers (M-G or M-H) between the mount and the TV as shown above to adjust

the length of the mounting bolt. Multiple spacers can be used in combination to achieve the desired bolt

depth. Square Washer (M-F) must be used in all configurations.

Attaching The Vesa Brackets To The TV

CAUTION:!

Using a bolt that is too long or

too short will damage the TV

and can cause serious injury

due to improper TV to TV

mount connection. Do not

overtighten screws.

Correct

Step 5

Step 6

Attaching the pull handle Adjusting the spring arm tension

HEAVY! You may need

assistance with this step.

a. Attach the Cross Bar (E) to the VESA Brackets (D) using Washer (P) and Bolt (O). Tighten securely

using Allen Wrench (Q).

b. Attach Pull Handle (F) to the Cross Bar (E) using Washer (P) and Bolt (N). Tighten securely using

Allen Wrench (Q).

The tension of the spring arm must match the weight of the TV for easy height adjustment of the TV.

The spring arm tension is set at the lowest level as factory default. Depending on the weight of the TV,

the spring arm tension may need to be increased.

Note: Omitting spring arm tension adjustment may result in your TV not staying in the desired position.

b. To attach the TV to the mount, remove the Nut

(D1) pictured, lower the latch as shown. Once

lowered, attach the VESA bracket to the TV Plate.

Raise the latch up and reinstall nut (D1) to secure

the TV in place.

Attaching TV To The Spring Arm

Adjust the height of the pull

handle to an accessible height.

The pull handle is used to raise

and lower the TV.

a.Insert the Allen Key into the hole as shown to

prevent the end of the mount from moving when

you are hanging the TV.

CAUTION: FAILURE TO FIX THE SPRING ARM

POSITION BY INSERTING ALLEN KEY

(Q) MAY RESULT IN INJURY ”

Note: Use the included ratchet wrench(R) and

ratchet bit(S) to adjust the tension adjustment.

To increase the tension (heavier TV) rotate the

Ratchet wrench clockwise(multiple rotations

might be required to reach the adequate spring

tension level.)

To decrease the tension (lighter TV) rotate the

Ratchet wrench (R) counter-clockwise (multiple

rotations might be required to reach the adequate

spring tension level.)

Note: The spring tension indicator will show the

current weight setting of the spring arm.

Please scan this QR code for a video guide

to adjust the spring arm tension

33lbs 44lbs 55lbs 66lbs

Step 7 Step 9

Step 8

Cable Management Positioning The TV

Route the cables through the cable

management clips located on the

bottom of the mount arm.

b. Adjust screen angle to desired viewing position.

If required the TV can be leveled post installation.

a. Remove the Allen key(previously

inserted to lock the spring arm

in step 8) to adjust the height

of the TV to the desired

position ”

To prevent injury

NEVER put your

hands or any object

into the mount's

structure.

Step 10 Step 11

+30°~-30°

+3°~-3°

Mount-It MI-395 Installation guide

Brand: Mount-It

Model: MI-395

Category: Fireplaces

Type: Installation guide

Here are some of the key features and benefits of the Mount-It! MI-395:

Easy height adjustment: The spring arm makes it easy to adjust the height of the TV to the desired position.
Convenient operation: The pull handle allows for easy operation of the mount, making it easy to raise and lower the TV.

Download PDF

report

Mount-It MI-395 Installation guide

Mount-It MI-395 Installation guide

Other documents