Active Line Array system
USER’S MANUAL
MAN173_1
www.moosesound.com
LOUD
PROUDLY DEVELOPED AND
MANUFACTURED IN PORTUGAL
MADE IN
PORTUGAL
100%
EUROPEAN
Dear customer,
Thank for choosing MOOSE branded products!
MOOSE is a brand of professional audio & lighting products, proudly developed and manufactured in
PORTUGAL.
In order to operate this product in a safe and reliable manner, please follow the instructions in this booklet and
before operating the equipment read the instructions carefully and please note the technical information.
Our products undergo very rigorous testing under strict conditions and they are monitored continuosly during the
manufacturing process. In order to guarantee the product function and safety, the original parts of the
manufacturer's design must be used. If any parts other than those of the manufacturer are used, or the product is
modified in any way, the user forfeits all warranty rights to claim.
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
To prevent electrical shock do not remove
the cover. No user serviceable parts inside.
Refer service to qualified personnel only.
Introduction
www.moosesound.com 2
Caution
The lightning flash with arrowhead symbol within an equilateral triangle is intended
to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to constitute a risk of
electrical shock.
The exclamation mark within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance instructions.
The amplifier is marked with this instruction so please
proceed accordingly in order to avoid any hazard.
1. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match
the values specified on the equipment.
2. If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet
with a protective ground. Never deactivate the protective ground of a power cord.
3. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before
extended periods of disuse.
4. Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an
authorised service company.
5. Do not open or modify this equipment.
6. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping
hazards.
7. Do not turn on the Amplifier ON before checking that all volumes to zero .
IMPORTANT: Never remove the cover, because otherwise there may be a risk of electric shock. There are no user
serviceable parts inside. Have repairs carried out only by qualified service personnel.
Active Line Array system
LOUD
MAN173_1
www.moosesound.com 3
Manufacturers Declaration
PROPER DISPOSAL OF THIS PRODUCT
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may not
be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled
waste disposal. Please dispose of this product separately from other waste and have it recycled to promote
sustainable economic activity.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details on where and how they can recycle this item in an environmentally friendly manner.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal .
ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION
Energy conservation is an active contribution to environmental protection. Please turn off all unneeded electrical
devices. To prevent unneeded devices from consuming power in standby mode, disconnect the mains plug.
EC DECLARATION OF CONFORMITY
The equipment marketed by MOOSE complies (where applicable) with the essential requirements and other
relevant specifications of Directives 1999/5/EC (R&TTE), 2004/108/EC (EMC) und 2006/95/EC (LVD). Additional
information can be requested to info@profactor.pt.
PROUDLY DEVELOPED AND MANUFACTURED IN PORTUGAL
Active Line Array system
LOUD
MAN173_1
www.moosesound.com 4
Connections and Controls
Please refer to the following scheme and instructions:
1. INPUT: Balanced signal input (Combi) for connection of an external audio source (e.g., mixer).
2. LINK: Balanced signal output (XLR 3p) for connection of another LOUD active system.
3. USB: USB 2.0 port (type B) to connect the cable to establish communication between DSP and computer.
4. PRESET LED: Preset LED indicator, from A to E, there are 5 storable and selectable presets.
5. PREST: Preset push button to select one of the 5 storable presets on the DSP, from A to E.
6. VOLUME: Master LEVEL system adjustment.
7. OUTPUT: Speaker output (NL4) for connection of the first LOUD205 array element. Min. load: 4Ohm. The other
3 array elements are signal linked from each other using the cables supplied.
8. MAINS IN: NEUTRIK powerCON socket, 85~264Vac, 50~60Hz Power-in (blue).
9. MAINS OUT: NEUTRIK powerCON socket, 85~264Vac, 50~60Hz Power-out (white).
10. POWER ON: Illuminated on/off switch. Before switching the system on/off, always adjust the volume to zero.
11. FUSE: Fuse holder. Replace the fuse only with a fuse of the same type and rating. If the fuse blows repeatedly,
please contact an authorised service company.
798
6
3
10
11
1 2 4 5
Active Line Array system
LOUD
S
U
E
F
CAUTION
RIS K O F E LECTR IC SHOCK . DO NOT OPE N.
To pr event elec tr ic al sh oc k d o not re move
the cover. No us er se r vicea ble par ts inside.
Refer ser vice to qual ifi ed pe rsonne l only.
BALANCED
PIN
SIGNAL SIGNAL
UNBALANCED
PIN
1 2 3 1 2 3
MAINS
85-264Vac
50HZ
OUTPUT
MID HI
PIN
SIGNAL
LOAD
4 Ohm min.
+1 -1 +2 -2
AC INPUT AC OUTPUT
POWER ON
FUSE F 5A
PROUDLY DEVELOPED AND MANUFACTURED IN PORTUGAL
Active line array system
Class D Amplifier
LOUD
Integrated DSP
MID/HI 720W rms
720W rms
LOW
PRESET
-80dB
0dB
A B C D E
INPUT THROUGH
USB
SPEAKER OUT
MAN173_1
Connections and Controls
Dimensions
Please refer to the following scheme and instructions:
www.moosesound.com 5
Active Line Array system
LOUD
INPUT LINK
Impedance - 16 Ohm
Power - 150W rms
+1 -1
+2 -2
OUTPUT MID HI
PIN
SIGNAL
205
LOUD
PROUDLY DEVELOPED AND
MANUFACTURED IN PORTUGAL
10. INPUT: Speakon compatible speaker connection. Bi-amp. setup (refer to the pinout printed in the connector
plate). Establish the connection between the subwoofer SPEAKER OUTPUT (6) and the first LOUD205 array
element.
11. LINK: Speakon compatible speaker link connection for connection of the next LOUD205 array element.
2
NOTE: the suited speaker cables (4x 1.5mm ) are supplied in the package.
IMPORTANT NOTE: LOUD system is designed for both ground stacking or flying operation. However, we consider
the flown position as being the ‘’standard’’ one. Facing this fact, when using the system on the floor operation the
metal grilles will show an upside down MOOSE logo as the system is used in what we call ‘’inverted position’’.
10 11
INPUT LINK
Impedance - 16 Ohm
Power - 150W rms
+1 -1
+2-2
OUTPUT MID HI
PIN
SIGNAL
205
LOUD
PROUDLY DEVELOPED AND
MANUFACTURED IN PORTUGAL
INPUT LINK
Impedance - 16 Ohm
Power - 150W rms
+1 -1
+2-2
OUTPUT MID HI
PIN
SIGNAL
205
LOUD
PROUDLY DEVELOPED AND
MANUFACTURED IN PORTUGAL
INPUT LINK
Impedance - 16 Ohm
Power - 150W rms
+1 -1
+2-2
OUTPUT MID HI
PIN
SIGNAL
205
LOUD
PROUDLY DEVELOPED AND
MANUFACTURED IN PORTUGAL
INPUT LINK
Impedance - 16 Ohm
Power - 150W rms
+1 -1
+2-2
OUTPUT MID HI
PIN
SIGNAL
205
LOUD
PROUDLY DEVELOPED AND
MANUFACTURED IN PORTUGAL
492
492
450
170
500
340
Speakon out
from amplifier (6)
Unit: mm (milimeters)
MAN173_1
www.moosesound.com 6
Technical specifications
MODEL LOUD SYSTEM
TYPE Active Line Array system
ENCLOSURE DESIGN Bass reflex (LOUD15)
Trapezoidal array element (LOUD205)
POWER OUTPUT (RMS) 700W (LOUD15)
400W (LOUD205)
FREQUENCY RANGE 45Hz - 19kHz
NOMINAL IMPEDANCE Speaker OUT: 4ohm min.
TRANSDUCER TYPE 15" LF (LOUD15)
2x 5" MF + 1" HF (LOUD205)
DISPERSION 120° H x Array length-splay dependent
CROSSOVER FREQUENCY Adjustable by integrated DSP
MAX. S.P.L. (PEAK) 128dB @ 1m (LOUD15)
113dB @ 1m (LOUD205)
CONSTRUCTION 15mm birch plywood, textured polyurea coating
GRILLE Custom perforated metal grille w/ acoustic foam
INSTALLATION, RIGGING, FLYING Integrated Al/Steel rigging system
DIMENSIONS (WxDxH)
19.29x19.49x16.93in (LOUD15), 19.29x13.39x6.69in (LOUD205)
490x495x430mm (LOUD15), 490x340x170mm (LOUD205)
WEIGHT 30Kg (LOUD15), 7,5Kg (LOUD205)
103.6lb (LOUD15), 16.5lb (LOUD205)
AMPLIFIER
POWER (RMS)
Class D - SMPS
720W + 720W @ 4ohm (2000W peak)
INDICATORS
OUTPUT/LINK
SPEAKER OUT
INPUT
Power, signal, preset in use
XLR 3p
XLR/Jack Combo connector
CONTROLS Master level, 5 selectable presets
PROTECTIONS
OPERATING VOLTAGE
Over current, short circuit, thermal, DC, HF
SMPS, 85-264Vac
Speakon® NL4
AC MAINS CONNECTOR NEUTRIK powerCON, Power-in / Power-out
PROFACTOR S.A., all rights reserved. The technical data and the functional product characteristics can be subject
to modifications. The photocopying, the translation, and all other forms of copying of fragments or of the integrlity
of this user's manual is prohibited.
Active Line Array system
LOUD
MAN173_1
CONJUNTO FL-LOUD15
Guilhotina:
Quinadora:
Puncionadora:
Base de dados:
Ordem:
Referência:
IMP86_1
19-02-2015
Nelson
Ref.ª do Aparelho
xxxx
DSS
Des. nº.
ISO 2768
CLASSE - M
Cliente
Revisão
Unidades
Substitui
Localização
Nome
do ficheiro
Páginas
Material
Cor
1
conjunto FS 205
Nome do desenho
mm
desenhou
nome
data
aprovou
15045
Tolerâncias
Espessura
/
1
MOOSE is a brand or PROFACTOR S.A.
www.moosesound.com
FL-LOUD15
Flying frame for LOUD15
460 interior
280,8
CONJUNTO FS 205
Guilhotina:
Quinadora:
Puncionadora:
Base de dados:
Ordem:
Referência:
IMP86_1
19-02-2015
Nelson
Ref.ª do Aparelho
xxxx
DSS
Des. nº.
ISO 2768
CLASSE - M
Cliente
Revisão
Unidades
Substitui
Localização
Nome
do ficheiro
Páginas
Material
Cor
1
conjunto FS 205
Nome do desenho
mm
desenhou
nome
data
aprovou
15045
Tolerâncias
Espessura
/
1
471
MOOSE is a brand or PROFACTOR S.A.
www.moosesound.com
FS-LOUD205
Stand support for LOUD205 stacking
www.moosesound.com
PROUDLY DEVELOPED AND
MANUFACTURED IN PORTUGAL
PROFACTOR S.A
Rua do Padrão 52
4440-617 Valongo
PORTUGAL
Telf.: +351 224 119 160
Fax: +351 224 155 822
info@profactor.pt
MOOSE is a brand or PROFACTOR S.A.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Citronic CX-5008 User manual
-
W Audio NL4 SpeakON User manual
-
Hantol HPSU720 Datasheet
-
Educational Insights Buck, Buck Moose Product Instructions
-
Interlogix JDS100 Installation guide
-
aija audio MP112A User manual
-
DAP Audio D3761 User manual
-
-
W Audio DSR 10A User manual
-
Craftsman Titanium Series Rear-Trigger Adjustable AquaGun Nozzle Manufacturer's Warranty
