Samsung PS-42P3S User manual

PDP-TELEVISION

(PLASMA DISPLAY PANEL)

PS42P3S

PS50P3H

PS63P3H

PS50P3H

PS63P3H

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

PICTURE IN PICTURE (PIP)

TELETEXT / TELEWEB

(OPTION)

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 1

2

ENG

Safety Instructions

◆ Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall.

◆ Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions.

◆ Do not expose the PDP to direct sunlight and other sources of heat.

◆ Do not expose the PDP to any liquids.

◆ Never put objects of any kind into the television, and do not place a water-containing vessel on the

PDP.

◆ During a storm conditions (especially when there is lightning) unplug the PDP from the mains

socket and aerial.

◆ Do not step on or twist the power cord.

◆ Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.

◆ Please use a soft and dry cloth (not containing volatile matter) when you clean the PDP.

◆ If the PDP is broken, do not try to repair it yourself. Contact qualified service personnel.

◆ If the remote control is not used for a long period of time, remove the batteries and store it in a

cool, dry place.

◆ Do not drop the remote control.

◆ When installing a PDP such as for an exhibition, etc., there is risk of overheating the unit if placed

directly on a floor or carpet. Be sure to use a proper stand, wall mount, ceiling mount, or Lift-Stand

offered by Samsung. (Do not use and exhibit by laying down or sitting the unit directly on the floor.)

User Instructions

◆ Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the

plasma monitor panel for more than 2 hours as it can cause screen image retention. This image

retention is also known as “screen burn”. To avoid such image retention, reduce the degree of

brightness and contrast of this screen when displaying a still image.

◆ Cell Defect

The plasma display panel consists of fine cells. Although the panels are produced with more than

99.9 percent active cells, there may be some cells that do not produce light or remain lit.

◆ Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place

over 2000m in height and do not install and operate there.

◆ Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 2

3

ENG

Caution

CAUTION:TO PREVENT ELECTRICAL SHOCK, DO NOT

REMOVE REAR COVER, NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

WARNING:

TO PREVENT DAMAGE WHICH MAY RESULT IN

FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

DNIe

TM

(Digital Natural Image engine)

This feature bring you more detailed image with 3D noise reduction, detail enhancement, contrast

enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer,

much detailed image to you. DNIe

TM

technology will fit every signals into your eyes.

The lightning flash and arrow

head within the triangle is a

warning sign alerting you of

“dangerous voltage” inside

the product.

The exclamation point within

the triangle is a warning sign

alerting you of important

instructions accompanying

the product.

☛

The main voltage is indicated on the

rear of the PDP and the frequency is

50 or 60Hz.



Owner’s Instructions

Remote Control/

AAA Batteries

Power Cord

Checking Parts

Component Cables

PC Cable

Antenna Cable

Ferrite Cores for

Speaker Wire

Speaker Wires

A Separated Sales

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 3

4

ENG

Contents

◆ FOREWORD

■ Safety Instructions......................................................................................... 2

■ User Instructions............................................................................................ 2

■ Caution .......................................................................................................... 3

◆ CONNECTING AND PREPARING YOUR DISPLAY

■ Your New Plasma Display Panel................................................................... 6

■ Infrared Remote Control ................................................................................ 8

■ IInserting the Batteries in the Remote Control............................................... 9

■ Installing the Display on the Wall Attachment Panel ..................................... 10

■ Connecting Speakers .................................................................................... 12

■ Connecting to an Aerial or Cable Television Network ................................... 14

■ Connecting a Satellite Receiver or Decoder.................................................. 14

■ Switching On and Off..................................................................................... 15

■ Placing in Standby Mode............................................................................... 15

■ Becoming Familiar with the Remote Control ................................................. 16

■ Setting Up Your Remote Control ................................................................... 17

■ Plug & Play Feature....................................................................................... 18

■ Choosing Your Language.............................................................................. 19

◆ SETTING THE CHANNELS

■ Storing Channels Automatically..................................................................... 20

■ Sorting the Stored Channels ......................................................................... 21

■ Storing Channels Manually............................................................................ 22

■ Assigning Names to Channels ...................................................................... 24

■ Activating the Child Lock and Skipping Unwanted Channels........................ 25

■ Selecting a Channel by Information............................................................... 26

◆ USING YOUR DISPLAY (continued)

■ Changing the Picture Standard ..................................................................... 26

■ Adjusting the Picture Settings........................................................................ 27

■ Adjusting the Picture Settings (PC or DVI Mode) .......................................... 28

■ Setting the Picture (PC Mode)....................................................................... 29

■ Setting the Picture (Component Mode) ......................................................... 30

■ Extra Picture Settings .................................................................................... 31

-

Digital NR

-

Size

-

LNA (Low Noise Amplifier)

■ Setting the Blue Screen................................................................................. 32

■ Selecting the Film Mode (Video or S-Video Mode) ....................................... 32

■ DNIe

TM

(Digital Natural Image engine) ............................................... 33

■ Freezing the Current Picture ......................................................................... 33

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 4

5

ENG

Contents(continued)

◆ USING YOUR DISPLAY

■ Changing the Sound Standard ...................................................................... 34

■ Adjusting the Sound Settings ........................................................................ 34

■ Extra Sound Settings..................................................................................... 35

-

Auto Volume

-

Melody

-

Pseudo Stereo / Virtual Surround

■ Selecting the DUAL Mode (depending on the model) ................................... 36

■ Setting the Time and Switching the TV On/Off Automatically ....................... 37

■ Setting the Sleep Timer ................................................................................. 38

■ Viewing the Picture In Picture (PIP) .............................................................. 39

■ Listening to the Sound of the Sub Picture (PC or DVI Mode)........................ 41

◆ USING THE TELETEXT FEATURE

■ Teletext Feature ............................................................................................ 42

■ Displaying the Teletext Information ............................................................... 43

■ Selecting Display Options.............................................................................. 43

■ Selecting the Teletext Source (Option).......................................................... 44

■ Selecting a Teletext Page.............................................................................. 45

◆ USING THE TELEWEB FEATURE

■ TeleWeb Feature (Option)............................................................................. 46

■ Using the TeleWeb Menu after Displaying the TeleWeb............................... 47

■ Easy Accessing the TeleWeb Service via the Remote Control ..................... 48

◆ ADDITIONAL INFORMATION AND CONNECTIONS

■ Viewing Pictures From External Sources ...................................................... 48

■ Connecting to the External Devices .............................................................. 49

■ Connecting to the DVD Input......................................................................... 50

■ Connecting to the S-Video Input.................................................................... 50

■ Connecting to the DVI Input .......................................................................... 51

■ Connecting to the PC Input ........................................................................... 51

■ Setting up Your PC Software (Windows only) ............................................... 52

■ Input Mode (PC/DVI) ..................................................................................... 53

■ Pin Configurations ......................................................................................... 54

◆ RECOMMENDATIONS FOR USE

■ Troubleshooting: Before Contacting Service Personnel................................ 55

☛

➢

Press Important Note

Symbols

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 5

6

ENG

Your New Plasma Display Panel

➢

The actual configuration on your PDP may be different,

depending on your model.

Front Panel

SOURCE

External input selection.

MENU

Menu display.

-

VOL +

Volume adjustment.

▼ CH ▲

Channel selection.

I /

Press to turn the PDP on and off.

Speaker

a

b

c

PS42P3S/PS50P3H

PS63P3H

a

b

c

a

Power Indicator

- Power Off; Red

- Power On; Off

- Timer On; Green

b

Remote Control Signal Receiver

Aim the remote control towards this spot on the

PDP.

c

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 6

7

Your New Plasma Display Panel (continued)

ENG

➢

The actual configuration on your PDP may be different,

depending on your model.

Rear Panel

b

a

d

c

h

k

i

e

g

j

f

a) ONLY FOR SERVICE

Connector for service only.

b) DVI IN

Connect to the video output jack for device with

DVI output.

c) AUDIO

Connect to the audio output jack on your PC or any

device with DVI output.

d) PC IN (RGB IN)

Connect to the video output jack on your PC.

e) MONITOR OUT (VIDEO / L-AUDIO-R)

Outputs for external devices

f) S-VIDEO IN / L-AUDIO-R / VIDEO IN

Video and audio inputs for external devices with an

S-Video output, such as a camcorder or VCR.

g) COMPONENT IN

Inputs for external devices, such as DVD, video

game device or video disc players.

h) EXT SPEAKER (8Ω)

Connect external speakers.

i) ANT IN VHF/UHF

75Ω Coaxial connector for Aerial/Cable Network.

j) WOOFER OUT

Connect to the sub-woofer speaker jack.

k) POWER IN

Connect the supplied power cord.

➢

For further details about connection, refer to pages 48~50.

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 7

8

Infrared Remote Control

ENG

SELECT CHANNEL BY

INFORMATION

MENU DISPLAY/

TELETEXT INDEX

DNIe ON/OFF/DEMO

MOVE TO THE REQUIRED

MENU OPTION/

ADJUST AN OPTION VALUE

RESPECTIVELY

TURNS THE PDP ON AND OFF

FASTEXT TOPIC SELECTION

INFORMATION DISPLAY/

TELETEXT REVEAL

EXIT FROM ANY DISPLAY

DIRECT CHANNEL SELECTION

TELEWEB HOME PAGE/

TELETEXT SUBPAGE

EXTERNAL INPUT SELECTION/

TELETEXT SIZE SELECTION

TUNES TO THE PREVIOUS CHANNEL

CONFIRM YOUR CHOICE

(STORE OR ENTER)

NEXT CHANNEL/

TELETEXT NEXT PAGE/

TELEWEB FORWARD

SOUND MODE SELECTION



IF YOUR REMOTE CONTROL IS NOT

FUNCTIONING PROPERLY, TAKE

OUT THE BATTERIES AND PRESS

THE RESET BUTTON FOR ABOUT

2~3 SECONDS. RE-INSERT THE

BATTERIES AND TRY USING THE

REMOTE CONTROL AGAIN.

PREVIOUS CHANNEL/

TELETEXT PREVIOUS PAGE/

TELEWEB BACKWARD

TELEWEB DISPLAY

(OPTION)

PIP FUNCTIONS;

- PIP ACTIVATING OR DEACTIVATING

(PIP ON)

- USED TO MOVE THE SUB PICTURE

COUNTERCLOCKWISE (LOCATE)

- USED TO ASSIGN A SOURCE OF SUB

PICTURE (SOURCE)

- SELECTING THE CHANNEL OF SUB

PICTURE (P

^

/

∨

)

MAKE THE REMOTE CONTROL WORKS

FOR TV, VCR, CATV, DVD PLAYER, STB

VCR/DVD FUNCTIONS;

- REWIND (REW)

- STOP

- PLAY/PAUSE

- FAST FORWARD (FF)

PRESS TO SELECT A PRESE TIME

INTERVAL FOR AUTOMATIC

SHUTOFF

VOLUME INCREASE

TEMPORARY SOUND SWITCH-OFF

VOLUME DECREASE

PICTURE EFFECT SELECTION/

TELETEXT CANCEL

PICTURE STILL

TELETEXT ON VIDEO & TEXT MIX

TELETEXT OFF

(Refer to page 43 for details)

➢

The performance of the remote control may be affected by bright light.

WHEN YOU PRESS A BUTTON , ‘

’

APPEARS ALONG WITH SELECED MODE

(TV, VCR, CATV, DVD OR STB) AND

REMAINING BATTERIES ON LED

PICTURE SIZE

CHANNEL SCAN

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 8

ENG

9

Inserting the Batteries in the Remote Control

You must insert or replace the batteries in the remote control when

you:

◆ Purchase the PDP

◆ Find that the remote control is no longer operating

correctly

1 Remove the cover on the rear of the remote control by pressing

the symbol ( ) downwards and then pulling firmly to remove it.

2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking

care to respect the polarities:

◆

-

on the battery against

-

on the remote control

◆

+

on the battery against

+

on the remote control

3 Replace the cover by aligning it with the base of the remote

control and pressing it back into place.

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 9

10

ENG

Installing the Display on the Wall Attachment Panel

Wall Mount Bracket

Mounting Kits

PS42P3S/50P3H: 4

PS63P3H: 6

Plastic Hanger Screws

How to Adjust Mounting Angle

1 Secure the PDP to the wall mount bracket.

(Please refer to the following instructions.)

2 Set the angle by pulling the upper end of the

PDP attached to bracket in the direction of the

arrow.

3 The angle can be adjusted from 0° to 20° by

±2°.

The wall mount bracket is delivered

separately. Please tighten the captive

screw in the direction of the arrow after

assembling the bracket.

☛

This wall mount bracket installation guide is for the following models: WMN4230/WMN5030/WMN6330.

This installation guide may be different from the PDP User’s manual. Please refer to the proper

installation guide for your product.

Installation Notes

◆

Do not install the PDP on any place other than vertical walls.

◆

To protect the performance of the PDP and prevent troubles, avoid the followings:

-

Do not install next to smoke and fire detectors.

-

Do not install in an area subjected to vibration or high voltage.

-

Do not install near or around any heating apparatus.

◆

Use only recommended parts and components.

PS42P3S/50P3H PS63P3H

(depending on your model)

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 10

11

ENG

Installing the Display on the Wall Attachment Panel

1 Remove the screws from the back of the PDP.

2 Use the screws and assemble the plastic hanger.

☛

◆ Please ask the installers to install the wall mount bracket.

◆ Please be sure to check if the plastic hanger is completely secured on both the left and right

side after hanging the PDP on the wall mount bracket.

◆ Please avoid catching your fingers while installing and adjusting the angle.

◆ Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP.

3 Tighten the screws of the plastic hanger to the back side of the PDP.

4 Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to

secure it to the wall mount bracket (

@). Tighten the screws as shown (#) so that the PDP cannot be

separated from wall mount bracket.

PDP panel

Wall attachment panel bracket

Wall

PS42P3S PS50P3H PS63P3H

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 11

12

ENG

Connecting Speakers

1 Remove the screws on the rear of the PDP.

2 Hang the two “T” shaped hangers

on the square holes on the rear of

the PDP.

3 Tighten the PDP and the speaker bracket using the screws removed from the PDP.

➢

When moving your PDP, do NOT hold the speaker connected to your PDP. It may damage the

bracket clamping the speaker and your PDP together and result in a drop of your PDP and a risk of

personal damage and injury.

PS42P3S PS50P3H PS63P3H

PS42P3S

PS50P3H

PS63P3H

PS42P3S PS50P3H PS63P3H

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 12

13

ENG

Connecting Speakers (continued)

Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching

the “+” and “

-

” ends of the cable with the diagram on the PDP.

Sub-woofer speaker

PS42P3S/PS50P3H

Sub-woofer speaker

PS63P3H

➢

◆ The speakers MUST have to a power

handling capability of 10 watts minimum

(impedance 8Ω).

◆ When you connect the speaker wire to the

external speaker out connector, first bind

the speaker wire round the ferrite core to

secure it.

Ferrite Cores

The ferrite cores are used to attenuate undesired signals.

When connecting cables, attach one of these ferrite cores to

the cable near the connector.

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 13

14

ENG

Connecting a Satellite Receiver or Decoder

In order to watch television programmes broadcast via a satellite

network, you must connect a satellite receiver to the rear of the

PDP. Also, in order to descramble a coded transmission signal, you

must connect a decoder to the rear of the PDP.

Using a Coaxial cable

Connect a coaxial cable to the:

◆ Receiver (or Decoder) output socket.

◆ Television aerial input socket.

➢

If you wish to connect both a satellite receiver (or decoder)

and a VCR, you should connect the:

◆ Receiver (or Decoder) to the VCR

◆ VCR to the PDP

Otherwise, connect the receiver (or decoder) directly to the

PDP.

Rear of the PDP

Satellite receiver/

Decoder

To view television channels correctly, a signal must be received by

the set from one of the following sources:

◆ An outdoor aerial

◆ A cable television network

◆ A satellite network

1 In the first three cases, connect the aerial or network input cable to

the 75Ω coaxial socket on the rear of the PDP.

2 If you are using an indoor aerial, you may need to turn it when

tuning your PDP until you obtain a picture that is both sharp and

clear.

For further details, refer to:

◆ “Storing Channels Automatically” on page 20

◆ “Storing Channels Manually” on page 22

➢

When installing or re-installing your PDP, be sure to use the

supplied coaxial antenna cable. If you connect using a different

coaxial cable, there is risk of noise or interference to the screen

image. (You must not use another general purpose cable.

Use the 3M/5M/7M cable supplied by Samsung.)

Connecting to an Aerial or Cable Television Network

Rear of the PDP

Cable Television

Network

or

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 14

15

The mains lead is attached to the rear of your PDP.

1 Plug the mains lead into an appropriate socket.

Result

: The Standby indicator on the front of the PDP lights up.

➢

The main voltage is indicated on the rear of the PDP and

the frequency is 50 or 60Hz.

2 Press the “ I / ” button on the front of the PDP (or POWER ()

button on the remote control) to switch the PDP on.

Result

: The programme that you were watching last is re-

selected automatically.

➣

If you have not yet stored any channels, No clear picture

appears. Refer to “Storing Channels Automatically” on page

20 or “Storing Channels Manually” on page 22.

3 To switch your PDP off, press the “ I / ” button again.

Your PDP can be placed in Standby mode, in order to reduce the

Power consumption.

The Standby mode can be useful when you wish to interrupt

viewing temporarily (during a meal, for example).

1 Press the POWER () button on the remote control.

Result

: The screen is turned off and the Standby indicator on

the front of the PDP lights.

2 To switch the PDP back on, simply press the POWER () button

again or a numeric button.

➣

You can also switch on by pressing the P or button.

Switching On and Off

Placing in Standby Mode

ENG

Front of the PDP

TV

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 15

16

ENG

Becoming Familiar with the Remote Control



The remote control is used mainly to:

◆ Change channels and adjust the volume

◆ Display the on-screen menu system

The following table presents the most frequently used buttons and

their functions.

Button Viewing Function Menu Function

Used to display the next

-

stored channel.

Used to display the

-

previous stored channel.

to Used to display the corresponding channels.

➢

For double digit channels, the second digit must be

pushed immediately after the first. Failure to do this will

result in a single digit channel being displayed.

PRE-CH Press the PRE-CH button. The TV will switch to the last

channel viewed.

To quickly switch between two channels that are far apart,

tune to one channel, then use the number button to select

second channel. Then, use the PRE-CH button to quickly

alternate between them.

Used to increase the

-

volume.

Used to decrease the

-

volume.

MUTE Used to switch the sound off temporarily.

➣

To turn the sound back on, press this button again, or

press the or button.

MENU Used to display the Used to return to the previous

on-screen menu system. menu or normal viewing.

-

Used to:

◆ Display a submenu

containing selections for

the current menu option

◆ Increase/decrease a

menu option value

-

Used to confirm your choice.

EXIT

-

Used to exit from the menu

system and return to normal

viewing directly.

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 16

17

Setting Up Your Remote Control

ENG

This TV’s remote control can operate VCR, CATV , DVD, or Set-top

box (STB), in addition to controlling the TV.

➣

The remote control is not compatible with the TV

manufactured by another company.

1 Turn off your VCR, Cable box (CATV), DVD or STB.

2 Press the SELECT button. Mode is changed whenever SELECT

button is pressed. (new mode is displayed on LED screen.)

3 Press the POWER () button on the remote control. The

component you select should turn on. If it turns on, your remote

control is now set correctly.

4 Once your remote control is set up, press the SELECT button any

time you want to use the remote control to operate your VCR,

Cable box, DVD or STB.

➣

When your remote control is in the VCR, CATV, DVD or

STB mode, the volume buttons still control your television’s

volume

VCR

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 17

18

ENG

When the television is initially powered ON, several basic customer

settings proceed automatically and subsequently. The following

settings are available.

1 If the television is in Standby mode, press the POWER () button

on the remote control.

Result

: The message Plug & Play is displayed. It flickers for

a little while, and then the

Language menu is

automatically displayed.

2 Select the appropriate language by pressing the † or … button.

3 Press the button to confirm your choice.

Result

: The message Antenna input check is displayed.

4 Make sure that the antenna is connected to the TV, and then

press the button.

Result

: The Country menu is displayed.

5 Select your country by pressing the † or … button.

6 Press the button to confirm your choice.

Result

:The

Auto Store menu is displayed.

7 To start the search, press the button.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in

the frequency range, (with lowest first and highest last).

The programme originally selected is then displayed.

➢ To stop the search before it has finished or return to normal

viewing, press the

MENU () button.

8 When it has finished, the message Enjoy viewing your new TV

is displayed, and then the channel which has been stored will be

activated.

Plug & Play Feature

Plug & Play

Enjoy viewing your new TV.

Language

Sel. Store

Antenna input check

Asia/W.Europe

CIS/E.Europe

China

Hongkong/UK

Australia

NZ/Indonesia

Area

Auto Store

Exit

Area Asia/W.Europe

1%

57 MHz P0

-----

Sel. Store

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 18

19

If you want to reset this feature...

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Function.

Result

: The options available in the Function group are

displayed.

3 Press the √ button.

4 Press the † or … button to select Plug & Play. Press the √

button.

Result

: The message Plug & Play is displayed.

5 For further details on how to set, refer to the opposite page.

When you start using your television for the first time, you must

select the language which will be used for displaying menus and

indications.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Function.

Result

: The options available in the

Function group are

displayed.

3 Press the √ button.

Result

: The Language option is selected.

4 Press the √ button again.

Result

: The languages available are listed.

5 Select the appropriate language by pressing the † or … button.

6 Press the button to confirm your choice.

7 When you are satisfied with your choice, press the MENU ()

button to return to normal viewing.

Plug & Play Feature (continued)

Choosing Your Language

ENG

Language English

Time

√√

Teletext Source Main

Plug & Play

√√

Blue Screen Off

Function

Move

√√

Enter Return

Language English

Time

√√

Teletext Source Main

Plug & Play

√√

Blue Screen Off

Function

Move

√√

Enter Return

Language

Sel. Store



BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 19

20

ENG

You can scan for the frequency ranges available to you, (availability

depends on your country). Automatically allocated programme

numbers may not correspond to actual or desired programme

numbers. However you can sort numbers manually and clear any

channels you do not wish to watch.

1 Press the MENU button.

Result

: The main menu is displayed.

2 Press the † or … button to select Channel.

Result

:

The options available in the

Channel

group are

displayed.

3 Press the √ button.

Result

: The Area option is selected.

4 Press the √ button again.

Result

: The countries available are listed.

5 Select your area by pressing the † or … button.

6 Press the button to confirm your choice

7 Press the MENU button.

Result

:

The options available in the

Channel

group are

displayed again

.

8 Press the † or … button to select Auto Store.

Press the

√ button.

Result

: The Auto Store menu is displayed.

9 Press the button to start the search.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in

the frequency range, (with lowest first and highest last).

The programme originally selected is then displayed.

➢ To stop the search before it has finished, press the

MENU ()button.

10 When the channels have been stored, you can:

◆ Sort them in the order required (see page 21)

◆ Clear a channel (see page 25)

◆ Fine-tune channel reception if necessary (see page 23)

◆ Assign a name to the stored channels (see page 24)

◆ Activate/deactivate the Digital Noise Reduction feature

(see page 31)

Storing Channels Automatically

Area Asia/W.Europe

Auto Store

√√

Manual Store

√√

Sort

√√

Name

√√

Edit

√√

Channel

Asia/W.Europe

CIS/E.Europe

China

Hongkong/UK

Australia

NZ/Indonesia

Area

Sel. Store

Auto Store

œœ √√

Sel. Exit Start

Area Asia/W.Europe

0%

0 MHz P0

-----

Move

√√

Enter Return

Area Asia/W.Europe

Auto Store

√√

Manual Store

√√

Sort

√√

Name

√√

Edit

√√

Channel

Move

√√

Enter Return

Auto Store

Exit

Area Asia/W.Europe

1%

57 MHz P0

-----

BN68-00481A (D60A_ENG_asia) 2004.2.9 3:51 PM Page 20

Page is loading ...

Samsung PS-42P3S User manual

This manual is also suitable for

Samsung PS-42P3S User manual

Related papers

Other documents