Stanley STDR5206 User manual

Brand: Stanley

Model: STDR5206

Category: Power tools

Type: User manual

STDR5206

English Page 3

Turkish Page 13

ENGLISH

(Original instructions)

FIG. A

FIG. B FIG. C

FIG. D FIG. E

ENGLISH

(Original instructions)

FIG. F

FIG. H

FIG. J

FIG. G

FIG. I

FIG. K

DO NOT RETURN THIS PRODUCT TO THE STORE,

ﬁrst contact your local STANLEY Ofﬁce

or nearest authorized service center.

Intended Use

This STANLEY screwdriver has been designed for driving

drywall fasteners through drywall board into timber or metal

framing studs.

General Safety Rules

Warning! Read and understand all instructions.

Failure to follow all instructions listed below, may

result in electric shock, ﬁre and/or serious personal injury.

Save These Instructions

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric shock, ﬁre

and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below

refers to your mains operated (corded) power tool or battery

operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodiﬁed plugs and matching outlets will reduce risk

of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric

shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock. Note: The term “Residual Curent Device

(RCD)” can be replaced by “Ground Fault Circuit

Interrupter (GFCI)” or by “Earth Leakage Circuit Breaker

(ELCB)”.

3. Personal safety

a. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

inﬂuence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your ﬁnger on the

switch or energising power tools that have the switch on

invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

ENGLISH

(Original instructions)

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a hazardous

situation.

5. Service

a. Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is

maintained.

Screwdriver safety warnings

Hold power tool by insulated gripping surfaces, when

performing an operation where the fastener may

contact hidden wiring or its own cord. Fasteners

contacting a "live" wire may make exposed metal parts of

the power tool "live" and could give the operator an electric

shock.

7. Electrical safety

Your tool is double insulated; therefore no earth

wire is required. Always check that the main

voltage corresponds to the voltage on the rating

plate.

Warning! If the power cord is damaged, it must be

replaced by the manufacturer, authorized

STANLEY Service Center or an equally qualiﬁed person in

order to avoid damage or injury. If the power cord is replaced

by an equally qualiﬁed person, but not authorized by

STANLEY, the warranty will not be valid.

Features (Fig. A)

1. Depth stop

2. Depth adjuster

3. Belt clip

4. Forward/Reverse switch

5. Variable speed trigger switch

6. Lock-on button

Speciﬁc Safety Rules

Warning! Know your drywall screwdriver. Do not plug the

tool into the power source until you have read and

understand this Instruction Manual. Learn the

tool’s applications and limitations, as well as the

speciﬁc potential hazards related to this tool.

• Following this rule will reduce the risk of electric shock,

ﬁre, or serious injury.

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

6. Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example:

2014 XX JN

Year of manufacturing

ENGLISH

(Original instructions)

ENGLISH

• Always wear eye protection. Any power tool can throw

foreign objects into your eyes and cause permanent eye

damage. ALWAYS wear safety goggles (not glasses) that

comply with ANSI safety standard Z87.1. Everyday

glasses have only impact resistant lenses. They ARE

NOT safety glasses

Warning! Glasses or goggles not in compliance with

ANSI Z87.1 could cause serious injury when they

break.

• Never use the drywall screwdriver to drive screws other

than drywall screws. The drywall screwdriver and the

screwdriver bits are designed speciﬁcally for driving

drywall screws.

• Only use screwdriver bits that are designed for use with

this tool.

• Always keep hands out of the path of the drywall screw.

Avoid awkward hand positions where a sudden slip could

cause your hand to move into the path of the saw blade.

• Make sure there are no nails or foreign objects in the

part of the workpiece to be cut or sanded.

• To avoid injury from accidental starting, always remove

the plug from the power source before installing or

removing a screwdriver bit or when adjusting the depth

control.

• Always check the wall area where screws will be driven

to be sure there are no hidden electrical wires in the

area.

• Never leave the Lock-on button ON. Before plugging the

tool into the power source, make sure the lock-on button

is OFF.

General Safety Warnings

Warning! Wear a dust mask that is designed to be

used when operating a power tool in a dusty

environment.

Warning! Dust that is created by power sanding,

sawing, grinding, drilling, and other construction

activities may contain chemicals that are known to

cause cancer, birth defects, or other genetic abnormalities.

These chemicals include:

• Lead from lead-based paints

• Crystalline silica from bricks, cement, and other masonry

products

• Arsenic and chromium from chemically treate lumber

The level of risk from exposure to these chemicals varies,

according to how often this type of work is performed. In

order to reduce exposure to these chemicals, work in a

well-ventilated area, and use approved safety equipment,

such as a dust mask that is speciﬁcally designed to ﬁlter out

microscopic particles.

Safety Extension Cord

Warning! Keep the extension cord clear of the

working area. Position the cord so it will not get

caught on the workpiece, tools or any other obstructions

while you are working with the power tool.

Make sure any extension cord used with this tool is in good

condition. When using an extension cord, be sure to use one

of heavy enough gauge to carry the current the tool will

draw. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating.

Be sure your extension cord is properly wired and in good

condition. Always replace a damaged extension cord or

have it repaired by a qualiﬁed electrician before using it.

Protect your extension cord from sharp objects, excessive

heat and damp or wet areas.

Use a separate electrical circuit for your power tools. This

circuit must not be less than 14 gauge wire and should be

protected with either a 15 A time delayed fuse or circuit

breaker. Before connecting the power tool to the power

source, make sure the switch is in the OFF position and the

power source is the same as indicated on the nameplate.

Running at lower voltage will damage the motor.

Contents

Carefully unpack the drywall screwdriver. Compare the

contents against the “Drywall screwdriver components” chart

below.

Assembly and Operating

Warning! To avoid ﬁre or toxic reaction, never use

gasoline, naphtha, acetone, lacquer thinner or

similar highly volatile solvents to clean the tool.

Forward/Reverse switch (Fig. B)

The forward/reverse switch (4) is conveniently mounted in

front of the variable speed trigger switch (5). To make the

screwdriver rotate clockwise for driving screws, push the

forward/reverse switch (4) to the left. To make the

screwdriver rotate counter-clockwise to remove screws,

push the forward/reverse switch (4) to the right.

(Original instructions)

ENGLISH

Notes:

a. Never change the position of the forward/reverse switch

(4) while the screwdriver bit is turning.

b. The variable speed trigger switch (5) will NOT function

with the forward/reverse switch (4) in the middle

position.

Variable speed trigger switch (Fig. C)

This screwdriver is equipped with a variable speed On/Off

trigger switch.

1. To start screwdriver, gently squeeze the variable speed

trigger switch (5).

Note: The screwdriver will turn at its slowest speed when

the variable speed trigger switch is depressed slightly. The

screwdriver will turn at its fastest speed when the variable

speed trigger switch is fully depressed.

2. To stop the screwdriver, release the variable speed

trigger switch (5).

Lock-on button (Fig. D)

The lock-on button feature allows the trigger switch to be

locked in the ON position at full speed when continuous

operation for extended periods of time is required.

To lock the lock-on button in the ON position, pull back on

the variable speed trigger switch (5) to start the screwdriver

and push the lock-on button (6) into the screwdriver handle.

Release the variable speed trigger switch while holding the

lock-on button into the screwdriver handle. The screwdriver

will continue to run. To release the lock-on button, pull

variable speed trigger switch back (5) and then release the

trigger.

Note: Operating the screwdriver with the variable speed

trigger switch for an extended period of time may cause the

screwdriver motor to overheat. If the screwdriver gets hot,

stop driving screws and allow it to cool for at least 15

minutes.

Inserting a screwdriver bit (Fig. E)

This tool has a magnetic bit holder that provides convenient

bit changes. To install a bit, simply insert the hex bit shank

(7) into the magnetic bit holder (8) that is located inside the

depth stop (1). Push the bit into the magnetic bit holder until

the magnet holds the bit in place.

Notes:

a. Use only 1” (25 mm) long bits that are designed for use

in driving drywall screws.

b. Make sure the bit size is correct for the drywall screws

being driven. This will usually be a #2 size.

Replacing the magnetic bit holder (Fig. F)

If the magnetic bit holder becomes worn or damaged, it must

be replaced. The replacement bit holder must be of the

same dimensions as the original and have the ANSI

retention groove on the end that is inserted into the tool.

1. Remove the nosepiece (2) by turning it counter

clockwise.

Note: Do not use pliers on the nosepiece. Only use your

hand.

2. Grasp the screwdriver bit (7) with pliers and pull it out of

the magnetic bit holder (8).

3. Grasp the large end of the bit holder with pliers and pull

it straight out of the screwdriver spindle (9).

4. Reverse the process by inserting the replacement

magnetic bit holder into the tool.

Note: When inserting the replacement for magnetic bit

holder, gently tap it into place to make sure it is fully inserted.

Grasp the large end of the magnetic bit holder to ensure the

retention groove (10) is holding the magnetic bit holder in

place in the tool.

5. Reinstall the screwdriver bit and nose piece.

Safety Recommendations

Check the following every time you use the screwdriver:

1. Wear safety glasses or a mask.

2. Use hearing protection.

3. The screwdriver tip is the right size and it is in good

condition.

4. No power cables “live” where you are inserting the

screws.

Note: Failure to follow these safety rules will signiﬁcantly

increase the risk of injury.

(Original instructions)

ENGLISH

(Original instructions)

Adjusting the screwdrive bit depth (Fig. G)

It is important to control the depth to which the drywall screw

will be driven. Over driving the screw will drive the screw too

deep and break the outer paper layer of the drywall. Under

driving the screw will leave the screw head above the

drywall surface making it impossible to properly ﬁnish the

drywall.

The depth control system is made up of the depth stop (1)

and the depth adjuster (2).

Warning! The following adjustments should always

be veriﬁed using a scrap piece of drywall to avoid

damaging the “good” drywall sections.

1. Rotate the depth adjuster counter clockwise until

approximately 1/4” of the screwdriver bit extends beyond

the depth stop.

2. Place a drywall screw onto the screwdriver bit. The

magnetized bit will hold the screw onto the bit.

Note: Before driving the screw, press the screw point into

the drywall and make sure the screw is perpendicular to the

drywall.

3. Press the screw against the drywall with steady even

pressure and squeeze the trigger switch. The clutch in

the tool will engage and the screw will be driven to the

preset depth.

4. If the screw is not driven deep enough, the head of the

screw will not be recessed into the drywall (Fig. H). In

this case, turn the depth adjustment sleeve clockwise

until the correct depth has been achieved. If the screw is

driven too deep, it will be recessed too far into the

drywall and the outer paper of the drywall will be

fractured (Fig. I). In this case, turn the depth adjustment

sleeve counter clockwise until the correct depth has

been achieved. Fig. J illustrates the correct depth for the

screw to be driven.

Note: For each revolution the depth adjustment sleeve is

rotated, the depth will increase/decrease approximately

1/16” (1.6 mm).

Tips for driving drywall screws

ff Always drive the screws perpendicular to the drywall so

the heads are properly countersunk. They should never be

driven at an angle.

• Support the tool with both hands wherever possible.

This will provide better control over the tool help

eliminate screws being driven at an angle.

• Place the drywall screw on the screwdriver bit. The

magnetic bit holder will hold any steel screw for easy

starting.

• Press the screw against the drywall with steady even

pressure and squeeze the variable speed trigger switch.

The clutch in the tool will engage and the screw will be

driven to the preset depth. Once fully driven, the clutch

will make a chattering sound until the variable speed

trigger is released.

• When the screw is properly driven, the screw head will

be slightly countersunk into the drywall without breaking

the outer drywall paper. At this point, the clutch will

release to prevent over driving the screw. This will result

in minimum work to ﬁll the holes and taping the seams.

• The belt clip allows you to conveniently attached the

screwdriver to your belt. This will allow you to use both

hands for positioning the drywall.

Removing drywall screws (Fig. K)

To remove drywall screws, remove the depth stop (1) to

expose the screwdriver bit.

Notes:

a. The depth stop is a press ﬁt onto the depth adjuster (2).

Simply twist and pull outward to slide it off the depth

adjuster.

b. You can also turn the depth adjuster clockwise to expose

the screwdriver bit. This however will cause you to lose

the depth setting and you will have to re-set the depth.

Maintenance

Keep guards, air vents and the motor housing as clear as

possible of dust and dirt. Wipe with a clean cloth and blow

through with a low-pressure air supply. Excessive build-up of

metal dust can cause tracking of electrical current from the

internal parts to exposed metal parts. Do not overload your

angle grinder. Overloading causes a reduction in speed and

efﬁciency, causing your angle grinder to become too hot. If

this happens, operate your angle grinder under no load for

one or two minutes until it has cooled to normal operating

temperature. Switching your angle grinder off under load will

reduce the life of the switch.

ENGLISH

(Original instructions)

Warning! When servicing, use only identical

replacement parts. The use of any other part may

create a hazard or cause product damage.

• DO NOT use solvents when cleaning plastic parts.

Plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use a clean cloth to remove dirt, dust, oil, grease etc.

Warning! Do not allow brake ﬂuids, gasoline,

petroleum-based products, penetrating oils, etc. to

come into contact with plastic parts. They contain chemicals

that can damage, weaken or destroy plastic.

• Remove accumulated dust and debris regularly using a

SOFT and DRY brush.

Warning! Use safety goggles when using an air jet

to blow dust out of the tool. Keep air vents clean

and unobstructed to allow maximum airﬂow through the tool.

• DO NOT abuse power tools. Abusive practices can

damage the tool and the workpiece.

Warning! DO NOT attempt to modify tools or

create accessories. Any such alteration or

modiﬁcation is misuse and could result in a hazardous

condition leading to possible serious injury. It will also void

the warranty.

Lubrication

All of the bearings in this tool are lubricated with a sufﬁcient

amount of high-grade lubricant for the life of the unit under

normal conditions. Therefore, no further lubrication is

required.

Cleaning

Use only mild soap and a slightly damp cloth to clean your

angle grinder. Many household cleaners contain chemicals

which could seriously damage the plastic. Also, do not use

petrol, turpentine, lacquer or paint thinners or similar

products. Never let any liquid get inside the tool and never

immerse any part of the tool into liquid.

Important! To assure product SAFETY and

RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be

performed by authorized service centers or other qualiﬁed

service personnel, always using identical replacement parts.

STDR5206

Power 520W

Voltage 230V

Frequency 50Hz

No-load speed 0-4500/min (rpm)

Weight 3.3lb (1.45kg)

Speciﬁcations

Level of sound pressure according to EN 60745:

Sound pressure (L

) 82 dB(A), uncertainty (K) 3 dB(A)

Sound power (L

) 93 dB(A), uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to

EN 60745:

Screwdriving without impact (a

h, S

)= 3,5 m/s²,

uncertainty (K) = 1.5 m/s²

The declared vibration emission values stated in the

technical data and the declaration of conformity have been

measured in accordance with a standard test method

provided by EN 60745 and may be used for comparing one

tool with another. The declared vibration emission value may

also be used in a preliminary assessment of exposure.

Warning! The vibration emission value during

actual use of the power tool can differ from the

declared value depending on the ways in which the tool is

used. The vibration level may increase above the level

stated. When assessing vibration exposure to determine

safety measures required by 2002/44/EC to protect persons

regularly using power tools in employment, an estimation of

vibration exposure should consider, the actual conditions of

use and the way the tool is used, including taking account of

all parts of the operating cycle such as the times when the

tool is switched off and when it is running idle in addition to

the trigger time.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you ﬁnd one day that your STANLEY product needs

replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand for raw

materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

STANLEY provides a facility for the collection and recycling

of STANLEY products once they have reached the end of

their working life. To take advantage of this service please

return your product to any authorised repair agent who will

collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local STANLEY ofﬁce at the

address indicated in this manual. Alternatively, a list of

authorised STANLEY repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

ENGLISH

(Original instructions)

Two years full warranty

If your STANLEY product becomes defective due to faulty

materials or workmanship within 24 months from the date of

purchase, STANLEY Europe guarantees to replace all

defective parts free of charge or – at our discretion – replace

the unit free of charge provided that:

• The product has not been misused and has been used in

accordance with the instruction manual.

• The product has been subject to fair wear and tear;

• Repairs have not been attempted by unauthorised

persons;

• Proof of purchase is produced.

• The STANLEY product is returned complete with all

original components

If you wish to make a claim, contact your seller or check the

location of your nearest authorised STANLEY repair agent in

the STANLEY catalogue or contact your local STANLEY

ofﬁce at the address indicated in this manual. A list of

authorised STANLEY repair agents and full details of our

after sales service is available on the internet

at:www.stanleytools.com

STANLEY declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60745-1, EN60745-2-2

These products also comply with Directive

2014/30/EU and 2011/65/EU. For more information, please

contact STANLEY at the following address or refer to the

back of the manual.

The undersigned is responsible for compilation of the

technical ﬁle and makes this declaration on behalf of

STANLEY.

R.Laverick

Engineering Manager

STANLEY , Europe, Egide Walschaertsstraat14-18,

2800 Mechelen, Belgium

01.2015

EC declaration of conformity

MACHINERY DIRECTIVE

STDR5206

Page is loading ...

Stanley STDR5206 User manual

Brand: Stanley

Model: STDR5206

Category: Power tools

Type: User manual

Download PDF

report

in other languages

Türkçe: Stanley STDR5206 Kullanım kılavuzu

Stanley STDR5206 User manual

Stanley STDR5206 User manual

in other languages

Related papers

Other documents