Sub-Zero CT30IU User guide

CT30IU
Sub-Zero
Brand
Sub-Zero
Model
CT30IU
Type
User guide

This manual is also suitable for

USE & CARE GUIDE
Induction Cooktops
Important Note
To ensure the safe and efcient use of Wolf equipment,
please take note of the following types of highlighted
information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION signals a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
Contents
Wolf Induction Cooktops . . . . . . . . . . . . . . . 3
Safety Instructions . . . . . . . . . . . . . . . . . . 4
Induction Cooktop Features. . . . . . . . . . . . . . 6
Induction Cooktop Operation . . . . . . . . . . . . . 9
Induction Cooktop Care . . . . . . . . . . . . . . . . 15
Troubleshooting Guide . . . . . . . . . . . . . . . . 17
Service Information . . . . . . . . . . . . . . . . . . 18
Wolf Warranty . . . . . . . . . . . . . . . . . . . . . 19
Features and specications are subject to change at any time
without notice. Visit our website, wolfappliance.com for the
most up-to-date information.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
Wolf Induction Cooktops 3
wolfappliance.com
Thank You
Your purchase of a Wolf induction cooktop attests to the
importance you place upon the quality and performance of
your cooking equipment. We understand this importance
and have designed and built your induction cooktop with
quality materials and workmanship to give you years of
dependable service.
We know you are eager to start cooking, but before you
do, please take some time to read this use & care guide.
Whether you are a beginning cook or an expert chef, it will
be to your benet to familiarize yourself with the safety
practices, features, operation and care recommendations
of the Wolf induction cooktop.
Your Wolf induction cooktop is protected by a warranty
that is one of the nest in the industry. Take a moment to
read the warranty statement at the end of this guide and
refer to it should service become necessary.
If service should become necessary, you will need the
model and serial numbers of the induction cooktop. Both
numbers are listed on the product rating plate, located
on the underside of the cooktop. Refer to the illustration
below.
IMPORTANT NOTE: Performance may be compromised if
the electrical supply is less than 240 volts.
MELT
H
I
GH
O
F
F
O
N
HI-POWER
HIGH
SIM
OFF
ON
CL
EA
R
O
FF
O
HI-POWER
HIGH
SIM
OFF ON
MELT
HIGH
OFF ON
Location of rating plate.
RATING PLATE
Safety Instructions 4
IMPORTANT INSTRUCTIONS
IMPORTANT NOTE: Read all safety instructions before
using this appliance.
•
Read this use & care guide carefully before using
your new cooktop to reduce the risk of re, electric
shock or injury to persons.
•
Ensure proper installation and servicing. This appli-
ance must be properly installed and grounded by
a qualied technician. Have the installer show you
the location of the circuit breaker or fuse so that you
know where to turn off power.
•
Warranty service must be performed by Wolf factory
certied service.
•
Before performing any service, disconnect the power
supply to the cooktop by switching off the circuit
breaker or removing the fuse.
GENERAL SAFETY REQUIREMENTS
•
Wear proper apparel. Never let loose clothing or
other ammable materials come in contact with the
elements while in operation. Fabric may ignite and
result in personal injury.
•
Use only dry pot holders when removing pans
from the cooktop. Wet or damp pot holders on hot
surfaces may result in burns from steam. Do not let
pot holders touch hot induction elements.
•
Select cookware of the proper size, material and
construction for the particular type of cooking being
done. This unit is equipped with induction elements
of different size. Refer to cookware selection on page
16.
•
Always turn pan handles inward so they do not
extend over adjacent work areas, induction elements
or edges of cooktop to reduce the risk of burns,
ignition of ammable materials and spillage due to
unintentional contact with pan. Do not turn handles
toward the room, where they may be bumped or
easily hit.
Safety Instructions 5
wolfappliance.com
•
Do not use water on grease res. Smother the ame
or use a dry chemical or foam-type extinguisher.
•
Never leave the cooktop unattended when using high
heat settings. Boilovers and greasy spillovers may
smoke or ignite.
•
Do not operate the cooktop if the glass-ceramic
surface is broken or severely pitted. Call Wolf factory
certied service to repair the cooktop.
•
Do not store ammable materials near hot compo-
nents or let grease or other ammable substances
accumulate on the cooktop.
•
Do not clean the cooktop while it is still hot. If using
a damp sponge or cloth, wait until the cooktop has
cooled sufficiently to prevent steam burns. Also,
some cleaners give off noxious fumes when applied
to hot surfaces. Refer to care recommendations on
page 14.
IMPORTANT INSTRUCTIONS
GENERAL SAFETY REQUIREMENTS
•
Never use your cooktop to warm or heat a room.
•
When using the cooktop, do not touch the glass
surface directly above or adjacent to the induction
elements. The glass surface may become hot enough
to cause burns after removing a pan with
hot contents.
•
Never heat an empty pan. It may damage the
cooktop or cookware and overheat the unit.
•
Do not heat cookware with water droplets on the
outside of the pan. The droplets may begin to boil
and splatter. Cookware should always be dry.
•
Do not use aluminum foil on the surface of the
cooktop.
•
Do not leave children alone or unattended in the area
where the cooktop is in use. Never allow children to
sit or stand on the appliance. Do not let children play
with the cooktop.
•
Do not store items of interest to children above or at
the back of the cooktop, as they could climb on the
appliance to reach items and be injured.
•
Do not repair or replace any part of the appliance
unless it is specically recommended in literature
you received. All service should be referred to Wolf
factory certied service.
• Illuminated touch controls with graduated control
lighting.
• Lock mode.
• Hot-surface indicator light.
• Universal off turns all elements off.
• Countdown timer with 1 to 99 minute range and adjust-
able volume.
• Two and ve year residential warranty—exclusions
apply—see warranty at the end of this guide.
ME
L
T
HIGH
OFF ON
H
I-PO
WER
HIGH
SIM
OFF
ON
CLE
AR
O
F
F
O
HI-PO
W
ER
HIGH
SI
M
OFF ON
M
ELT
HIGH
O
FF
ON
Illuminated touch
controls
Four induction
elements
Hot-surface
indicator light
Countdown timer
Stainless steel trim
Lock key
ME
L
T
HIGH
OFF ON
OFF ON
SIM
HIGH
HI-POWER
OF
F
O
C
LEAR
Illuminated touch
controls
Two induction
elements
Lock key
Hot-surface
indicator light
Countdown timer
Stainless steel trim
Induction Cooktop Features 6
15" (381) FRAMED INDUCTION COOKTOP
Model CT15I/S
30" (762) FRAMED INDUCTION COOKTOP
Model CT30I/S
Framed Induction Cooktop Features
• Induction elements heat iron and other magnetic
cookware instantly, while cooktop surface stays cool.
• Framed models with stainless steel trim.
• Ceran glass-ceramic surface for scratch resistance
and easy cleaning.
• High-efciency induction elements deliver power and
control.
• Cookware sensing—elements will not be energized
without an induction-compatible pan on the surface.
• Wolf exclusive Hi-Flux induction elements sense pan
size to focus power for optimum performance.
• Wolf exclusive Hi-Power mode boosts power to the
element.
• Wolf exclusive melt setting for gentle heat and true
simmer setting prevents scorching.
Universal off
Universal off
Induction Cooktop Features 7
wolfappliance.com
M
ELT
H
IG
H
OFF ON
MEL
T
H
IGH
OF
F
ON
OFF ON
SIM
HIGH
HI-POW
E
R
OFF
ON
S
IM
HIGH
HI-
PO
W
ER
H
I-P
O
W
E
R
HIGH
SIM
OFF ON
CLEAR
OFF
O
OPTIONAL ACCESSORIES
Optional accessories are avail able through your authorized
Wolf dealer. For local dealer information, visit the nd a
showroom section of our website, wolfappliance.com.
• Filler strip for installation with another cooktop or
module (framed models).
• Support bracket for installation with another module
and downdraft (model CT15I/S).
36" (914) FRAMED INDUCTION COOKTOP
Model CT36I/S
Illuminated touch
controls
Five induction
elements
Hot-surface
indicator light
Countdown timer
Stainless steel trim
Lock key
Universal off
Induction Cooktop Features
Heating Zone Diameter and Power
15" (381) INDUCTION COOKTOP WATTS
8
3
/4" (220) 1800 / 3000 boost
6
3
/4" (171) 1200
30" (762) INDUCTION COOKTOP WATTS
(2) 8
3
/4" (220) 1800 / 3000 boost
6
3
/4" (171) 1200
5
1
/2" (140) 1200
36" (914) INDUCTION COOKTOP WATTS
11" (280) 3000 / 4000 boost
(2) 8
3
/4" (220) 1800 / 3000 boost
6
3
/4" (171) 1200
5
1
/2" (140) 1200
Induction Cooktop Features 8
Unframed Induction Cooktop Features
• Induction elements heat iron and other magnetic
cookware instantly, while cooktop surface stays cool.
• Unframed models can be mounted ush with
countertop.
• Ceran glass-ceramic surface for scratch resistance
and easy cleaning.
• High-efciency induction elements deliver power and
control.
• Cookware sensing—elements will not be energized
without an induction-compatible pan on the surface.
• Wolf exclusive Hi-Flux induction elements sense pan
size to focus power for optimum performance.
• Wolf exclusive Hi-Power mode boosts power to the
element.
• Wolf exclusive melt setting for gentle heat and true
simmer setting prevents scorching.
M
EL
T
HIG
H
OFF ON
MEL
T
H
IGH
OFF ON
OFF
ON
SIM
HIGH
HI-POW
E
R
OFF
ON
SIM
HIGH
HI-PO
W
ER
H
I-P
O
W
E
R
HIGH
SIM
OFF ON
CLEAR
OFF
O
MEL
T
HIGH
OFF ON
HI-POWE
R
HIGH
SIM
OFF
ON
CLE
AR
O
F
F
O
HI-PO
W
ER
HIGH
SI
M
OFF ON
M
ELT
HIGH
O
FF
ON
Illuminated touch
controls
Four induction
elements
Hot-surface
indicator light
Countdown timer
Unframed edge
Lock key
30" (762) UNFRAMED INDUCTION COOKTOP
Model CT30IU
36" (914) UNFRAMED INDUCTION COOKTOP
Model CT36IU
Universal off
Illuminated touch
controls
Five induction elements
Hot-surface
indicator light
Countdown timer
Unframed edge
Lock key
Universal off
• Illuminated touch controls with graduated control
lighting.
• Lock mode.
• Hot-surface indicator light.
• Universal off turns all elements off.
• Countdown timer with 1 to 99 minute range and adjust-
able volume.
• Two and ve year residential warranty—exclusions
apply—see warranty at the end of this guide.
Induction Cooktop Operation 9
wolfappliance.com
Control Panel
The control panel of your induction cooktop is illuminated
for instant visual indication that one or more elements
are in use. The control panel features touch controls with
graduated control lighting. A power bar indicator in each
control will display the heat setting level for the element.
Refer to the illustration below.
CAUTION
Do not place hot cookware directly over the control
panel.
Induction Cooking
Induction cooking has been used in Europe for decades
by professionals and homeowners demanding the best in
performance.
In induction cooking, the electricity ows through a coil to
produce a magnetic eld under the ceramic cooktop.
When a cast iron or magnetic stainless steel pan is placed
on the glass-ceramic surface, currents are induced in the
cooking utensil and instant heat is generated due to the
resistance of the pan. Induction only works with cooking
vessels made of magnetic materials, such as cast iron and
magnetic stainless steel (it will not work with aluminum or
copper pots). To test the cookware, a magnet must stick
to the bottom of the vessel in order to function.
BENEFITS OF INDUCTION COOKING
Speed. Heating is immediate. Adjustment is immediate. No
slow change from heating up to cooling down. Heats up to
50% faster than gas or electric cooktops.
Controllability. Homogeneous cooking to distribute the
heat perfectly (no hot or burned spots). You can keep
sauces and chocolates melted at 50 watts of power, or
with the touch of a nger, activate Hi-Power mode and boil
water in half the time you normally do.
Energy efciency. Energy is supplied directly to the
cooking vessel so 85% to 90% of the electric energy gets
used to cook. This means a cooler kitchen and cooktop.
Easy to clean. The surface remains relatively cool, so
overows and spills do not stick or burn onto the element.
The surface will be warm after removing a saucepan with
hot contents. Wait until the surface cools to clean with
soapy water.
OFF
O
MELT
HIGH
OFF ON
OFF ON
MELT
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
HIGH
SIM
CLEAR
Control panel (CT36I/S shown).
POWER BAR
INDICATOR
Induction Cooktop Operation 10
Cooktop Operation
LOCK MODE
If the cooktop remains idle for more than 5 minutes, it
automatically enters lock mode. In lock mode, all touch
pad operations on the control panel are disabled and all
induction elements are turned off. A steady glowing light
within the “key” symbol indicates that the cooktop is
locked. Refer to the illustration below.
• To unlock the control panel, touch and hold the key
symbol for 5 seconds. Two chimes will sound and the
light within the key symbol will go out. All touch pad
operations are enabled.
• To lock the control panel, touch and hold the key
symbol for 3 seconds. Three chimes will sound and the
light within the key symbol will illuminate. The cooktop
is now in lock mode.
IMPORTANT NOTE: When the cooktop is powered up
for the rst time or if there has been a power outage, the
cooktop will default to lock mode.
OFF
O
MELT
HIGH
OFF ON
OFF ON
MELT
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
HIGH
SIM
CLEAR
Lock mode (CT36I/S shown).
KEY SYMBOL
TOUCH PAD
INITIAL START-UP
Before using your induction cooktop for the rst time,
clean the glass-ceramic surface as recommended in the
cleaning section on page 15. The cooktop surface must be
free of any foreign substances, especially those that could
melt and permanently adhere to the glass-ceramic surface.
When the cooktop is powered up for the rst time it will
default to lock mode. To unlock the control panel, touch
and hold the key symbol for 5 seconds.
IMPORTANT NOTE: A small amount of smoke and odor
may be noticed during the initial break-in period.
Induction Cooktop Operation 11
wolfappliance.com
Cooktop Operation
ELEMENT ACTIVATION
To activate an induction element, touch the OFF ON touch
pad that corresponds to the element you wish to use.
The power bar indicator will begin to blink and show a half-
power status.
To complete the activation, touch one of the following
symbols or touch pads of the element control while the
power bar indicator is still blinking:
• Touch SIM or MELT to set the power output at the
lowest heat setting and complete the activation.
• Touch the + or – symbol to set the power output at the
medium heat setting and complete the activation.
• Touch HIGH to set the power output at the high heat
setting and complete the activation.
• Touch HI-POWER to set the power output at the
maximum level and complete the activation.
OFF
O
MELT
HIGH
OFF ON
OFF ON
MELT
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
HIGH
SIM
CLEAR
Element activation.
Heat settings.
OFF
O
MELT
HIGH
OFF ON
OFF ON
MELT
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
HIGH
SIM
CLEAR
OFF ON
TOUCH PAD
+ AND –
SYMBOLS
SIM
TOUCH PAD
HIGH
TOUCH PAD
ELEMENT ACTIVATION
To change the heat setting—the element is activated and
the power bar indicator remains steadily lit:
• Touch SIM or MELT to decrease the setting directly to
the lowest heat.
• Touch the + or – symbol to change the heat setting
incrementally up or down.
• Touch HIGH to increase the heat setting directly to
high.
• Touch HI-POWER to boost to Hi-Power mode.
• Touch OFF ON to turn the element off.
IMPORTANT NOTE: If no cookware or an incompatible
pan is placed on an induction element after activation,
the control will blink for 30 seconds, then the element will
automatically shut off.
Induction Cooktop Operation 12
HOT SURFACE INDICATOR
As a safety precaution, a hot-surface indicator light will
illuminate when the surface temperature of any one of the
induction elements rises above 150°F (65°C). ‘HOT’ will
illuminate in the control panel display. It will remain illumi-
nated until the entire surface temperature has lowered to a
safe level, even after the cooktop controls are turned off.
TIMER OPERATION
The induction cooktop features a countdown timer located
in the control panel. Refer to the illustration below.
The timer may be set in one-minute increments up to 99
minutes. Once set, the remaining time will be illuminated in
the control panel as it counts down. The timer can be used
anytime the cooktop is not in lock mode.
• To start the timer, touch + on the timer control. Touch
and hold + or – until the desired time is shown in the
timer display. The timer will begin its countdown in
minutes, 3 seconds after the time is set.
• A warning chime will sound when the timer has one
minute left and begins to countdown in seconds.
• When the timer reaches 0, an audible chime will sound.
The chime will continue to sound every 30 seconds
until CLEAR is touched.
OFF
O
MELT
HIGH
OFF ON
OFF ON
MELT
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
HIGH
SIM
CLEAR
Hot-surface indicator.
Timer control.
OFF
O
MELT
HIGH
OFF ON
OFF ON
MELT
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
HIGH
SIM
CLEAR
HOT-SURFACE
INDICATOR LIGHT
CLEAR
TOUCH PAD
+ AND –
TOUCH PADS
Cooktop Operation
HI-POWER MODE
Hi-Power mode boosts power on one induction element
by diverting power from an adjacent element. This mode is
suitable for frying foods or boiling water rapidly.
To activate Hi-Power mode, touch the OFF ON touch pad
for the element you wish to use. Then touch HI-POWER.
Power from an adjacent element will automatically be
diverted to the element. If the adjacent element is on HIGH
power, the power output will be reduced. This reduction in
power will be displayed in the power bar indicator of the
adjacent element.
OFF
O
MELT
HIGH
OFF ON
OFF ON
MELT
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
HIGH
SIM
CLEAR
Hi-Power mode (CT36I/S
shown).
HI-POWER
TOUCH PAD
Induction Cooktop Operation 13
wolfappliance.com
Cooktop Operation
UNIVERSAL OFF
To turn off all induction elements at the same time, touch
the universal OFF touch pad on the control panel. Refer to
the illustration below.
COOLING FAN
The induction cooktop is equipped with a cooling fan that
automatically turns on to cool internal parts. The fan will
turn off once internal temperatures have been lowered.
During extended use, the cooling fan may continue to run
even after the cooktop has been turned off until internal
temperatures have been lowered.
OFF
O
MELT
HIGH
OFF ON
OFF ON
MELT
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
HIGH
SIM
CLEAR
Universal off.
UNIVERSAL OFF
TOUCH PAD
SOUND ADJUSTMENT
The volume and frequency, or tone, of the touch controls
can be adjusted through the user option, activated through
the timer controls.
• To activate the user option, the cooktop must be
unlocked.
• Touch and hold CLEAR for 3 seconds to activate the
volume adjustment option. ‘Uol’ will illuminate in the
control panel display.
• Touch and hold CLEAR for 5 seconds to activate the
frequency adjustment option. ‘FrE’ will illuminate in the
control panel display.
• Adjust the volume and frequency using the + and –
touch pads. One touch equals one step up or down.
The power bar indicator of the right rear element will
display the volume or frequency level. (1 bar = low,
8 bars = medium and 16 bars = high.)
• As the volume or frequency is adjusted, the cooktop
will chime with each change. The chime will represent
the volume and frequency level currently displayed by
the power bar indicator.
• To exit the user option, touch and hold CLEAR for
more than 7 seconds. If no touch pad is touched for 10
seconds, the level is then stored.
OFF
O
MELT
HIGH
OFF ON
OFF ON
MELT
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
SIM
HIGH
H
I
-
P
O
W
E
R
OFF ON
HIGH
SIM
CLEAR
Sound adjustment.
CLEAR
TOUCH PAD
+ AND –
TOUCH PADS
Induction Cooktop Operation 14
Care Recommendations
• Do not use the cooktop as a cutting board.
• Do not slide cookware with a rough bottom, such as
cast iron, across the glass-ceramic surface. If this
occurs, remove any marks with a nonabrasive cleaner.
• Do not allow any item that could melt to come in
contact with the glass-ceramic surface when it is hot.
If this occurs, use the razor blade scraper provided with
the cooktop to remove.
• Do not place food directly on the glass-ceramic surface
when it is hot.
• Do not operate the cooktop if the glass-ceramic surface
is broken. Contact Wolf factory certied service.
• Do not place a trivet, wok support ring or other metal
stand directly onto the cooktop surface.
• Do not apply chlorine bleach, ammonia or other strong
chemicals or cleaners to the cooktop surface.
• Do not wipe the cooktop surface with a cloth that may
leave a lm of detergent; it will cause the cooktop to
discolor during the next heating cycle.
IMPORTANT NOTE: Do not place hot cookware near the
sealed outer edges of ush-mounted unframed cooktops.
This will cause damage to the silicone seal.
Cooktop Operation
TEMPERATURE SETTING GUIDE
SETTING USES
MELT
Melting, holding chocolate
1 Bar Melting butter
Heating, holding delicate sauces
Warming foods
SIMMER
Melting large quantities
2–4 Bars Simmering sauces
Steaming rice
LOW to MEDIUM
Frying eggs
10–12 Bars Heating milk, soups, cream sauces,
gravies and puddings
Panfrying
Simmering large quantities
Boiling vegetables in water
MEDIUM to HIGH
Sautéing
12–14 Bars Browning
Braising
Quick frying
Fast boiling large quantities
HIGH
Boiling water
All Bars Heating broth soups, stocks
Deep fat frying (to heat oil only)
HI-POWER BOOST
Rapid boiling
Frying at high temperatures
wolfappliance.com
Induction Cooktop Care 15
Care Recommendations
CLEANING
• Lock the cooktop before cleaning by touching and
holding the key symbol for 3 seconds.
• Clean the cooktop surface thoroughly before operating
for the rst time and after each use.
• Wait until the cooktop surface is cool before cleaning. It
will be safe to clean if the hot-surface indicator light is
not illuminated.
• For best results, wipe up spills and spatters as they
occur and immediately after the cooktop has cooled.
If spills with a high sugar content are allowed to cook
on, they may permanently damage the glass-ceramic
surface. Use the razor blade scraper provided with the
cooktop to remove heavy or burned-on spills.
• Do not use abrasive cleaners or applicators; they will
permanently scratch cooktop surfaces.
• Use a spray degreaser to remove ngerprints and
greasy spatters.
• To clean the glass-ceramic surface, use a nonabrasive
cleaner like Elco Cooktop Cleaning Creme and apply
with a lightly dampened cloth. Remove any cleaning
residue from the surface and wipe with a dry cloth.
• To clean the stainless steel trim of framed models, use
a nonabrasive stainless steel cleaner and apply with a
soft lint-free cloth. Remove any cleaning residue from
the trim and wipe with a dry cloth.
MAINTENANCE
The Wolf induction cooktop is a sealed system that does
not require internal maintenance. The cleaning and care
recommendations outline necessary maintenance for the
glass-ceramic surface. All other maintenance must be
performed by Wolf factory certied service.
Induction Cooktop Care 16
Cookware Selection
Cookware selection is crucial in the performance of induc-
tion cooking. Use the following guidelines when selecting
cookware:
• Magnetic stainless steel or cast iron cookware is
required for induction cooking. To test, a magnet must
stick to the bottom of the cookware. Aluminum, copper,
glass and certain stainless steel cookware will not
function with induction elements.
• For optimum performance, select cookware with a
diameter that matches the diameter of the induc-
tion element. When a pan is placed on the element, it
should not extend beyond the ring around the element.
The diameter of the pan must also meet or exceed
the minimum listed for each element, or the induction
element will not function. Refer to the cookware
selection guide.
• Avoid pots and pans with uneven or rounded bottom
surfaces. Some specialty cookware such as woks,
pressure cookers, canning modules and deep fat fryers
must be carefully selected to meet induction cooking
criteria.
IMPORTANT NOTE: Digital and magnetic thermometers
may produce inaccurate readings.
COOKWARE SELECTION GUIDE
MODEL ELEMENT DIAMETER PAN (min)
15" COOKTOP
Front 6
3
/4" (171) 3
1
/2" (89)
Rear 8
3
/4" (220) 5
1
/2" (140)
30" COOKTOP
Left Front 8
3
/4" (220) 5
1
/2" (140)
Left Rear 5
1
/2" (140) 3
1
/2" (89)
Right Front 6
3
/4" (171) 3
1
/2" (89)
Right Rear 8
3
/4" (220) 5
1
/2" (140)
36" COOKTOP
Left Front 8
3
/4" (220) 5
1
/2" (140)
Left Rear 5
1
/2" (140) 3
1
/2" (89)
Middle Front 6
3
/4" (171) 3
1
/2" (89)
Middle Rear 8
3
/4" (220) 5
1
/2" (140)
Right Rear 11" (280) 7" (178)
wolfappliance.com
Troubleshooting Guide 17
Troubleshooting
If your Wolf induction cooktop is not operating properly,
use the following troubleshooting guide before calling
Wolf factory certied service. This guide will save you
time and trouble and may help you avoid the expense of a
service call.
Cooktop does not operate.
• Cooktop is in lock mode. Touch and hold the key
symbol for 5 seconds to unlock the control panel.
• Cooktop is in lock mode and displays an error code.
Errors may be cleared by pressing the clear touch pad.
If error reappears, contact Wolf customer care.
• Check the household fuse or circuit breaker to see if it
has been blown or tripped. A power outage may also
have caused a disruption in service.
• Verify that the electrical connection to the cooktop has
not been disconnected.
Control panel blinks and cooktop does not operate.
• Improper cookware is being used. Select proper
cookware as outlined in the cookware selection guide
on the previous page.
Induction elements do not heat properly.
• Electrical connection is loose. Have an electrician
tighten electrical connections.
• Cooktop is not connected to a proper electrical circuit.
Have an electrician verify that the proper voltage is
being supplied to the cooktop.
Food does not heat properly.
• Improper cookware is being used. Select proper
cookware as outlined in the cookware selection guide
on the previous page.
Service Information 18
BEFORE CALLING FOR SERVICE
Before calling Wolf factory certied service, refer to the
troubleshooting guide on page 17.
PRODUCT REGISTRATION
Register your new Wolf product today so that we may
ensure your satisfaction. You may register by one of the
following options:
1) Mail in the completed Wolf product registration card.
2) Register online at wolfappliance.com.
3) Register by phone by calling Wolf customer care at
800-222-7820.
The model and serial numbers of your appliance are
printed on the enclosed Wolf product registration card. If
you provide us with your e-mail address, we will send you
exciting new product updates and recipes as they become
available, along with information on special events.
The information and images in this guide are the copyright property of Wolf Appliance, Inc. Neither this guide nor any information or images contained herein
may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc. ©Wolf Appliance, Inc. all rights reserved.
Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc.
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care and The Living Kitchen are registered trademarks and service marks of Sub-Zero, Inc.
(collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
Service Information
When requesting information, literature, replacement parts
or service, always refer to the model and serial numbers
of your induction cooktop. Both numbers are listed on
the product rating plate, located on the underside of the
cooktop. Refer to the illustration on page 3. Record the
rating plate information below for future reference.
Model Number:
Serial Number:
Installation Date:
Wolf Factory Certied Service:
Phone:
Authorized Wolf Dealer:
Phone:
Wolf Appliance Products Limited Warranty
FOR RESIDENTIAL USE ONLY
FULL TWO YEAR WARRANTY*
For two years from the date of original installation, your Wolf Appliance product warranty covers all parts
and labor to repair or replace, under normal residential use, any part of the product that proves to be defec-
tive in materials or workmanship. All service provided by Wolf Appliance under the above warranty must be
performed by Wolf factory certied service, unless otherwise specied by Wolf Appliance, Inc. Service will be
provided during normal business hours.
LIMITED FIVE YEAR WARRANTY
For ve years from the date of original installation, Wolf Appliance will repair or replace the following parts
that prove to be defective in materials or workmanship: gas burners (excluding appearance), electric heating
elements, blower motors (ventilation hoods), electronic control boards, magnetron tubes and induction
generators. The part(s) will be repaired or replaced, free of charge, with the owner paying for all other costs
including labor. All service provided by Wolf Appliance under the above warranty must be performed by Wolf
factory certied service, unless otherwise specied by Wolf Appliance, Inc. Service will be provided during
normal business hours.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to products
installed in any one of the fty states of the United States, the District of Columbia or the ten provinces of
Canada. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident
or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT WOLF APPLIANCE,
INC. WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION
OF LAW. WOLF APPLIANCE, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDEN-
TAL DAMAGES ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER
EXPRESS, IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Wolf factory certied service nearest you, contact Wolf
Appliance, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,
wolfappliance.com or call 800-222-7820.
*Stainless steel doors, panels, handles, product frames and interior surfaces are covered by a limited 60-day
parts and labor warranty for cosmetic defects.
*Replacement lters for ventilation hood recirculating kits are not covered by the product warranty.
WOLF APPLIANCE, INC. P. O. BOX 44848 MADISON, WI 53744 WOLFAPPLIANCE.COM 800.222.7820
819052 REV-A 9/2011
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Sub-Zero CT30IU User guide

CT30IU
Sub-Zero
Brand
Sub-Zero
Model
CT30IU
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents