Philips GC4490/02 User manual

Page is loading ...

6

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet from the support that

Philips offers, register your product at www.philips.com/welcome.

General description (Fig. 1)

A Spray nozzle

B Cap of lling opening

C Steam boost

D Spray button

E Steam control

F Ionic DeepSteam button (specic types only)

G Ionic DeepSteam light (specic types only)

H Temperature dial

I Specic types only: Amber temperature light with (specic types only) red automatic shut-off

(AUTO/OFF) indication.

J Specic types only: Amber temperature light with red automatic shut-off (AUTO/OFF)

indication

K Mains cord

L Type plate

M Soleplate

N Calc-Clean button

Not shown: Heat-resistant protective cover (specic types only)

Not shown: Delicate fabric protector (specic types only)

Important

Read this user manual carefully before you use the appliance and save it for future reference.

Danger

- Never immerse the iron in water.

Warning

- Check if the voltage indicated on the type plate corresponds to the local mains voltage before

you connect the appliance.

- Do not use the appliance if the plug, the mains cord or the appliance itself shows visible damage,

or if the appliance has been dropped or leaks.

- If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by

Philips or similarly qualied persons in order to avoid a hazard.

- Never leave the appliance unattended when it is connected to the mains.

- This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their

safety.

- Children should be supervised to ensure that they do not play with the appliance.

- Do not let the mains cord come into contact with the hot soleplate of the iron.

Caution

- Only connect the appliance to an earthed wall socket.

- Check the mains cord regularly for possible damage.

- The soleplate of the iron can become extremely hot and may cause burns if touched.

- When you have nished ironing, when you clean the appliance, when you ll or empty the

water tank and also when you leave the iron even for a short while: set the steam control to

position 0, put the iron on its heel and remove the mains plug from the wall socket.

- Always place and use the iron on a stable, level and horizontal surface.

ENGLISH

4239.000.6219.5.indd 6 21-10-09 14:05

- Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the

water tank.

- This appliance is intended for household use only.

Electromagnetic elds (EMF)

This Philips appliance complies with all standards regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this user manual, the appliance is safe to use based on

scientic evidence available today.

Before rst use

1 Remove any sticker, protective foil or plastic from the soleplate.

2 Rinseanddrythellingcup.

Preparing for use

Filling the water tank

1 Makesuretheapplianceisunplugged.

2 Setthesteamcontroltoposition0(=nosteam)(Fig.2).

3 Openthecapofthellingopening.

4 Tilttheironbackwardsandusethellingcuptollthewatertankwithtapwateruptothe

maximum.(Fig.3)

Do not ll the water tank beyond the MAX indication.

Donotputperfume,vinegar,starch,descalingagents,ironingaidsorotherchemicalsinthewater

tank.

, Ifthetapwaterinyourareaisveryhard,weadviseyoutomixitwithanequalportionof

distilledwater,ortousedistilledwateronly.

5 Closethecapofthellingopening(‘click’)(Fig.4).

Setting the temperature

1 Specictypesonly:Removetheheat-resistantprotectivecover(Fig.5).

Donotleavetheheat-resistantprotectivecoveronthesoleplateduringironing.

2 Puttheirononitsheel.

3 Tosettherequiredironingtemperature,turnthetemperaturedialtotheappropriate

position(Fig.6).

Check the laundry care label for the required ironing temperature:

- 1 for synthetic fabrics (e.g. acrylic, nylon, polyamide, polyester)

- 1 for silk

- 2 for wool

- 3 for cotton

- MAX for linen

If you do not know what kind or kinds of fabric an article is made of, determine the right ironing

temperature by ironing a part that will not be visible when you wear or use the article.

Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches. To

prevent stains, do not use the spray function.

Start ironing the articles that require the lowest ironing temperature, such as those made of

synthetic bres.

4 Putthemainspluginanearthedwallsocket.

ENGLISH 7

4239.000.6219.5.indd 7 21-10-09 14:05

, Theambertemperaturelightgoeson.

5 Whentheambertemperaturelighthasgoneout,waitawhilebeforeyoustartironing.

The temperature light goes on from time to time during ironing.

Using the appliance

Note: The iron may give off some smoke when you use it for the rst time. This stops after a short while.

Steam ironing

1 Makesurethatthereisenoughwaterinthewatertank.

2 Settherequiredironingtemperature(seechapter‘Preparingforuse’,section‘Settingthe

temperature).

3 Settheappropriatesteamsetting.Makesurethatthesteamsettingyouselectissuitablefor

thesetironingtemperature:(Fig.7)

- 1 - 3 for moderate steam (temperature settings 2 to 3)

- 4 - 6 for strong steam (temperature settings 3 to MAX)

Note: The iron starts to produce steam as soon as it reaches the set temperature.

Note: If the set ironing temperature is too low (MIN to 2), water may drip from the soleplate (see

chapter ‘Features, section ‘Drip stop’).

Ironing with Ionic DeepSteam (specic types only)

When you use the Ionic DeepSteam function during steam ironing, the steam produced is ner than

during regular steam ironing. Fine steam reaches deeper, especially into thick fabrics. This helps you

to remove stubborn creases easily.

1 Followsteps1to3insection‘Steamironing’.

2 PressandholdtheIonicDeepSteambutton(Fig.8).

, TheIonicDeepSteamlightgoesonandyouhearahummingsound.(Fig.9)

3 TheironnowproducesIonicDeepSteamtohelpyouremoveeventhetoughestcreases.

Note: The Ionic DeepSteam function is only effective when it is used in combination with a steam setting

and a temperature setting between 2 and MAX.

Note: Do not use the Ionic DeepSteam function when you iron without steam and/or at low temperature

settings. However, ironing at low temperatures without steam with the Ionic DeepSteam function

switched on will not damage the iron.

Note: The Ionic DeepSteam output may vary from time to time, depending on the ironing temperature.

Ironing without steam

1 Setthesteamcontroltoposition0(=nosteam)(Fig.2).

DonotusetheIonicDeepSteamfunction,asthisfunctionhasnoeffectwhenyouironwithout

steam.

2 Settherequiredironingtemperature(seechapter‘Preparingforuse’,section‘Settingthe

temperature’).

After ironing

1 Removethemainsplugfromthewallsocket.

2 Ifyouhavebeensteamironing,emptythewatertank.

3 Let the iron cool down in a safe place.

ENGLISH8

4239.000.6219.5.indd 8 21-10-09 14:05

Features

Spray function

You can use the spray function at any temperature to moisten the article to be ironed. This helps

remove stubborn creases.

1 Makesurethatthereisenoughwaterinthewatertank.

2 Pressthespraybuttonseveraltimestomoistenthearticletobeironed(Fig.10).

Steam boost function

A steam boost from the special Steam Tip soleplate helps remove stubborn creases. The steam

boost enhances the distribution of steam into every part of your garment.

The steam boost function can only be used at temperature settings between 3 and MAX.

1 Pressandreleasethesteamboostbutton(Fig.11).

Vertical steam boost

1 Youcanalsousethesteamboostfunctionwhenyouholdtheironinvertical

position.(Fig.12)

This is useful for removing creases from hanging clothes, curtains etc.

Never direct the steam at people.

Drip stop

This iron is equipped with a drip-stop function: the iron automatically stops producing steam when

the temperature is too low, to prevent water from dripping out of the soleplate. When this happens,

you may hear a sound.

Automatic shut-off function (specic types only)

The automatic shut-off function automatically switches off the iron if it has not been moved for a

while.

, TheredAUTO/OFFindicationofthetemperaturelightashestoindicatethattheironhas

beenswitchedoffbytheautomaticshut-offfunction.

To let the iron heat up again:

1 Pickuptheironormoveitslightly.

, TheredAUTO/OFFindicationgoesout.

, Ifthetemperatureofthesoleplatehasdroppedbelowthesetironingtemperature,the

ambertemperaturelightgoeson.

2 Iftheambertemperaturelightgoesonafteryouhavemovedtheiron,waitforittogoout

beforeyoustartironing.

Note: If the amber temperature light does not go on after you move the iron, the soleplate still has the

right temperature and the iron is ready for use.

Delicate fabric protector (specic types only)

The delicate fabric protector protects delicate fabrics from heat damage and shiny patches.

With the delicate fabric protector you can iron delicate fabrics (silk, wool and nylon) at temperature

settings 3 to MAX in combination with all steam functions available on the iron.

The delicate fabric protector reduces the soleplate temperature instantly, thus allowing you to iron

delicate fabrics safely.

If you do not know what kind or kinds of fabric an article is made of, determine the right ironing

temperature by ironing a part that is not visible when you wear or use the article.

1 Puttheirononthedelicatefabricprotector(‘click’)(Fig.13).

ENGLISH 9

4239.000.6219.5.indd 9 21-10-09 14:05

Cleaning and maintenance

Cleaning

1 Wipeakesandanyotherdepositsoffthesoleplatewithadampclothandanon-abrasive

(liquid)cleaningagent.

Tokeepthesoleplatesmooth,avoidhardcontactwithmetalobjects.Neveruseascouringpad,

vinegarorotherchemicalstocleanthesoleplate.

2 Cleantheupperpartoftheironwithadampcloth.

3 Regularlyrinsethewatertankwithwater.Emptythewatertankafteryouhaverinsedit.

Double-Active Calc System

The Double-Active Calc System consists of an Anti-Calc tablet inside the water tank combined with

the Calc-Clean function.

1 The Anti-Calc tablet prevents scale from clogging the steam vents. This tablet is constantly active

and does not need to be replaced.

2 The Calc-Clean function removes the scale particles from the iron.

Using the Calc-Clean function

Use the Calc-Clean function once every two weeks. If the water in your area is very hard (i.e. when

akes come out of the soleplate during ironing), use the Calc-Clean function more frequently.

1 Makesuretheapplianceisunplugged.

2 Set the steam control to position 0.

3 Fillthewatertanktothemaximumlevel.

Donotputvinegarorotherdescalingagentsinthewatertank.

4 SetthetemperaturedialtoMAX(Fig.14).

5 Putthepluginanearthedwallsocket.

6 Unplugtheironwhenthetemperaturelightgoesout.

7 Holdtheironoverthesink,pressandholdtheCalc-Cleanbuttonandgentlyshaketheiron

toandfro(Fig.15).

, Steamandboilingwatercomeoutofthesoleplate.Impuritiesandakes(ifany)areushed

out.

8 ReleasetheCalc-Cleanbuttonassoonasallthewaterinthetankhasbeenusedup.

Repeat the Calc-Clean process if the iron still contains a lot of impurities.

After the Calc-Clean process

1 Puttheplugbackintothewallsocketandlettheironheatuptoletthesoleplatedry.

2 Unplugtheironwhenithasreachedthesetironingtemperature.

3 Movethehotirongentlyoverapieceofusedclothtoremoveanywaterstainsthatmay

have formed on the soleplate.

4 Lettheironcooldownbeforeyoustoreit.

Storage

1 Setthesteamcontroltoposition0andunplugtheiron.

2 Emptythewatertank(Fig.16).

ENGLISH10

4239.000.6219.5.indd 10 21-10-09 14:05

3 Let the iron cool down in a safe place.

4 Windthemainscordandxitwiththecordbinder.(Fig.17)

5 Storetheirononitsheelonastablesurface.

Heat-resistant protective cover (specic types only)

You can store the iron on the heat-resistant protective cover immediately after ironing. It is not

necessary to let the iron cool down rst.

Donotusetheheat-resistantprotectivecoverduringironing.

1 Puttheironontheheat-resistantprotectivecover(Fig.18).

2 Insertthetipofthesoleplateintotheheat-resistantprotectivecover(1)andthenpress

down the heel of the iron (2).

Environment

- Do not throw away the appliance with the normal household waste at the end of its life, but

hand it in at an ofcial collection point for recycling. By doing this, you help to preserve the

environment (Fig. 19).

Guarantee & service

If you need information or if you have a problem, please visit the Philips website at www.philips.com

or contact the Philips Consumer Care Centre in your country (you nd its phone number in the

worldwide guarantee leaet). If there is no Consumer Care Centre in your country, go to your local

Philips dealer.

Troubleshooting

If the appliance does not work or does not work properly, rst check the list below. If the problem

is not mentioned in this list, the appliance probably has a defect. In that case we advise you to take

the appliance to your dealer or to an authorised Philips service centre.

Problem Possiblecause Solution

The iron is

plugged in, but the

soleplate is cold.

There is a connection

problem.

Check the mains cord, the plug and the wall

socket.

The temperature dial is set

to MIN.

Set the temperature dial to the required

position.

The iron does not

produce any

steam.

There is not enough water

in the water tank.

Fill the water tank (see chapter ‘Preparing for

use’, section ‘Filling the water tank’).

The steam control is set to

position 0.

Set the steam control to a position between

1 and 6 (see chapter ‘Using the appliance’,

section ‘Steam ironing’).

The iron is not hot enough

and/or the drip-stop

function has been activated.

Set an ironing temperature that is suitable for

steam ironing ( 2 to MAX). Put the iron on

its heel and wait until the temperature light

has gone out before you start ironing.

ENGLISH 11

4239.000.6219.5.indd 11 21-10-09 14:05

Problem Possiblecause Solution

The iron does not

produce a steam

boost.

You have used the steam

boost function too often

within a very short period.

Continue ironing in horizontal position and

wait a while before you use the steam boost

function again.

The iron is not hot enough. Set an ironing temperature at which the

steam boost function can be used ( 3 to

MAX). Put the iron on its heel and wait until

the temperature light has gone out before

you use the steam boost function.

Water droplets

drip onto the

fabric during

ironing.

You have not closed the cap

of the lling opening

properly.

Press the cap until you hear a click.

You have put an additive in

the water tank.

Rinse the water tank and do not put any

additive in the water tank.

The set temperature is too

low for steam ironing.

Set a temperature of or 2 higher.

You have used the steam

boost function at a

temperature setting below

3.

Set the temperature dial to a setting between

3 and MAX.

Water drips from

the soleplate after

the iron has

cooled down or

has been stored.

You have put the iron in

horizontal position with

water still left in the water

tank.

Empty the water tank.

Flakes and

impurities come

out of the

soleplate during

ironing.

Hard water forms akes

inside the soleplate.

Use the Calc-Clean function one or more

times (see chapter ‘Cleaning and

maintenance’, section ‘Using the Calc-Clean

function’).

The red light

ashes (specic

types only).

The automatic shut-off

function has switched off the

iron (see chapter ‘Features’,

section ‘Automatic shut-off

function’).

Move the iron slightly to deactivate the

automatic shut-off function. The red AUTO/

OFF light goes out.

The iron makes a

humming sound.

The Ionic DeepSteam

function is on.

If you hear the humming sound when you

iron without steam, stop pressing the Ionic

DeepSteam button. The Ionic DeepSteam

function has no effect when you iron without

steam.

ENGLISH12

4239.000.6219.5.indd 12 21-10-09 14:05

Page is loading ...

Philips GC4490/02 User manual

This manual is also suitable for

Philips GC4490/02 User manual

in other languages

Related papers

Other documents