Candy PA 640/2 X UK User manual

11

1

93786974

INSTRUCTION FOR THE INSTALLATION ANDINSTRUCTION FOR THE INSTALLATION AND

INSTRUCTION FOR THE INSTALLATION AND

OPERATION OF HOBSOPERATION OF HOBS

OPERATION OF HOBS

~~~





PA 640/2 F PA 640/2 F

PA 640/2 F





PA 640/2 UK PA 640/2 UK

PA 640/2 UK

22

2

Unpacking the appliance ............................................................... 3

Recommendations ....................................................................... 3

Presentation of the hob / Technical data .......................................... 4

• INSTALLATION

Safety instructions........................................................................ 5

Modification of the factory gas setting :

* Fitting of the correct jets ........................................................ 6

* Adjusting of the air ring ......................................................... 7

Fitting the hob ........................................................................ 8/9

Gas connection .........................................................................10

Electrical connection .................................................................. 11

After final installation of the hob (if modification of the gas setting) :

Adjusting of the lower flame on the gas burners .............................. 12

• USING THE APPLIANCE

The different gas burners ............................................................13

Igniting and setting the burner ..................................................... 14

General maintenance .................................................................. 15

CONTENTSCONTENTS

CONTENTS

33

3

UNPACKING THE APPLIANCEUNPACKING THE APPLIANCE

UNPACKING THE APPLIANCE

Inside the appliance, you will find :

• a plastic bag containing :

- the new jets for the gas modification, if required,

- the fixing brackets with screws to install the hob in the worktop,

and,

• a spanner to change the jets if the factory gas setting does not correspond to your

installation requirements.

PLEASE READ THE FOLLOWING CAREFULLY IN ORDER TO GET THE BEST FROM

YOUR APPLIANCE.

Please keep the operating and installation instructions in a safe place for future reference.

Before fixing the hob, note the serial number of the appliance just in case you may require

future repairs from after sales service organisation.

. Rating plate (located under the lower casing of the hob)

• All accessible parts of the hob become hot while it is in operation. Always, keep

children away from it.

• The hob should be given a quick clean after each use, to avoid the accumulation of

spillages and grease, which if not removed, will harden and could cause the production of

smoke and unpleasant smells.

• When cooking with fats or oils, never leave gas burner unattended. Overheated fats or

oils can quickly catch fire.

RECOMMENDATIONSRECOMMENDATIONS

RECOMMENDATIONS

44

4

PA 64PA 64

PA 64

0/2 UK :0/2 UK :

0/2 UK :

4 gas burners, and enamelled pan supports.4 gas burners, and enamelled pan supports.

4 gas burners, and enamelled pan supports.

OveralOveral

Overal

l dimensions :l dimensions :

l dimensions :

Width : 59 cm Depth : 51 cm Height : 3 cm

Building-in dimensions Building-in dimensions

Building-in dimensions

--

- (see chapter "Installation")

Width : 56 cm Depth : 48 cm

PRESENTATION

ALL GAS HOB

TOUT GAZ

S

e

m

i

-

f

a

s

t

1

,

4

5

k

W

F

a

s

t

2

,

5

k

W

S

e

m

i

-

f

a

s

t

1

,

4

5

k

W

V

e

r

y

f

a

s

t

3

,

2

k

W

In order to improve the quality of the products, CANDY may carry out modifications linked

to technical improvements.

Appliance meeting with the standard CEE 89/336, 73/23 and 90/396.

TECHNICAL DATA

renrubtsaF

tfeltnorf

tsaf-imeS

renrub

tfelraer

renrubtsaF

thgirraer

renruftsaf-imeS

thgirtnorf

KU2/046AP-F2/046APKU2/046AP-F2/046AP

KU2/046AP-F2/046AP

KU2/046AP-F2/046APKU2/046AP-F2/046AP

Wk2,3Wk54,1Wk5,2Wk54,1

rabm02-02G

h/l918

rabm52-52G

h/l379

rabm03-8203G

h/g726

rabm7313G

h/g616

PA 64PA 64

PA 64

0/2 F :0/2 F :

0/2 F :

4 gas burners, and cast-iron pan supports.4 gas burners, and cast-iron pan supports.

4 gas burners, and cast-iron pan supports.

55

5

Before installing the hob :

n make sure that the appliance is compatible with the gas supply source.

The hob is pre-set in the factory to work with the type of gas shown on the packing

and the plate attached to it.

Natural gas G 20-20 mbar / G 25-25 mbar : mains gas

o if necessary, adapt the hob for use with another type of gas : if the hob

must be used with another type of gas than the gas pre-set in the factory, it is necessary

to adapt the hob gas burners (page 6/7).

The procedure for adaptation consists of :

. fitting the correct jets to ensure nominal delivery,

. adjusting the appearance of the flame by regulating the air ring according to the

data given in the table.

For installation :

p built-in hob (page 8/9).

q make the gas connection according to the type of gas to be used : based on

the gas to be used, choose the appropriate gas connection (page 10).

r make the hob electrical connection according to the instructions (page

11).

s adjusting the minimum flame of the taps : if necessary, adjust the minimum

flame of the taps by turning the by-pass screw (page 12).

)

INSTALLATIONINSTALLATION

INSTALLATION

Installing a domestic appliance can be a complicated operation which if not

carried out correctly, can seriously affect consumer safety.

It is for this reason that the task should be undertaken by a professionally

qualified person who will carry it out in accordance with the technical regulations

in force.

In the event that this advice is ignored and the installation is carried out by an

unqualified person, CANDY declines all responsibility for any technical failure

of the product whether or not it results in damage to goods or injury to

individuals.

All modification concerning the hob gas setting must be indicated on the rating plate

of the hob.

)

66

6

• CHANGING THE GAS TYPE : the calorific power output and gas pressure will

vary according to the gas supply. Burner setting must be carried out once the gas and

electrical installation is complete.

When changing gas type, you must follow the procedure below :

. fit the correct jets,

. adjust the appearance of the flame by regulating the air ring.

. adjust the minimum flame on the taps (see page 12).

• CHANGING THE JETS :

Each jet is designated by size. A special spanner supplied with the appliance is designed to

hold the jets securely during the set up operation.

To gain access to the jets :

. remove the pan supports,

. remove the burner cap and body,

. using the spanner supplied with the appliance, unscrew

the jet,

. fit the correct jet for the type of gas to be used,

. secure the jet tightly,

. replace the burner body, cap and the pan support.

INSTALLATION:

"GAS CONNECTION""GAS CONNECTION"

"GAS CONNECTION"

Jet

Burner

body

Example : Fast ring gas burner 3,2 kW

G20-20 mbar / G25-25 mbar

G30 28-30 mbar

G31 37 mbar

Jet

96

Jet

122

Jets

94 x 2

Jet

96

Jet

61

Jet

80

Jets

65 x 2

Jet

61

1,45 kW 2,5 kW

3,2 kW

1,45 kW

Fast

Semi-

fast

Semi-

fast

Fast

4 gas burners

77

7

• SETTING THE APPEARANCE OF THE FLAME

1. Regulating the air ring on the hob burners : the setting is important as it ensures the

correct combustion and enables the burners to work at maximum efficiency. The table

refers to the value "X" in mm ; it may be necessary to regulate this by plus or minus 1 mm

to obtain a perfect flame.

2. To gain access to the air rings on the hob burners: remove the pan support, the burner

cap and body of the relevant burner. The air ring is located at the lengthening of the burner

unit which is fixed by a screw (see drawing).

If necessary : . unscrew the screw that holds the air flow adjuster,

. set the correct distance according to the air adjuster protrudes,

. secure the screw when the operation is completed.

INSTALLATION:

"GAS CONNECTION""GAS CONNECTION"

"GAS CONNECTION"

Quota

X

Air ring

Air

ring

Semi-fast burner 1,45 kW

or Fast burner 2,5 kW

Fast burner 3,2 kW

Quota

X

Quota "X" in mm of the air ring according to the gas setting

Screw

G20-20 mbar

G25-25 mbar

G30 28-30 mbar G31 37 mbar

6 10

14 6

00

7 9

14 7

Fast

Semi-fast Fast

Semi-fast

88

8

INSTALLATION:

"BUILDING-IN""BUILDING-IN"

"BUILDING-IN"

BUILDING-IN :BUILDING-IN :

BUILDING-IN : both the unit into which the hob will be fitted and any adjacent kitchen

furniture must be made from heat resistant material and fixed with heat resistant adhesive.

If, when installing the hob, the lower part of the casing is adjacent to an area normally

accessible when handling or cleaning, fit a partition 1 cm below the base of the casing with

a 10x10 cm opening at the rear right-hand corner, to avoid any risk of burning or damage.

There should also be a 5 cm gap between the appliance and all adjacent vertical surfaces.

A foam adhesive is supplied with the hob. Stick this seal under the edge of the body as near

as possible to the outer edge of the hob. Press round the edges of the hob, so that the seal

flattens out and ensures an air tight seal.

Warning :Warning :

Warning : at the rear of the appliance, take care not to block the air inlets necessary for

combustion to take place.

FITTING THE SEALFITTING THE SEAL

FITTING THE SEAL

• •

•

Top view of the sealTop view of the seal

Top view of the seal

••

•

Cross section of the hobCross section of the hob

Cross section of the hob

Worktop levelWorktop level

Worktop level

6 mm

seal

- Take care not to block the air inlets- Take care not to block the air inlets

- Take care not to block the air inlets

necessary for combustion to take place -necessary for combustion to take place -

necessary for combustion to take place -

SEAL

99

9

The body of the hob is fitted with 4 location holes to take the fixing brackets that secure the

hob in the unit. Place the 4 fixing brackets in such a way that the hob is placed perfectly in

the support unit.

Location for fixing bracketsLocation for fixing brackets

Location for fixing brackets

Building-in according to TYPE XBuilding-in according to TYPE X

Building-in according to TYPE X

(Norm CEI 335-2-6)(Norm CEI 335-2-6)

(Norm CEI 335-2-6)

INSTALLATION:

"BUILDING-IN""BUILDING-IN"

"BUILDING-IN"

Fixing

bracket

Opening

10x10 cm

1010

10

INSTALLATION:

"GAS CONNECTION""GAS CONNECTION"

"GAS CONNECTION"

The hob can be built-in ; it is type "X" for built-in hob (in compliance with electrical

regulations EN 60.335.2.6) ; in class 3 (in compliance with gas norm EN 30.1.1) ;

adjoining furniture should not be higher than the level of the hob.

This appliance is not connected to an evacuation device for the products of combustion. It

must be installed and connected in compliance with the norms in force in the country of

installation. Particular attention should be given to the availability of ventilation. The turno-

ver of air necessary for combustion is a minimum of 2 m

3

/h per kW of power.

Gas connection should be carried out in compliance with the norms in force in the

country of installation. A stop tap, a regulator valve or a release valve for propane gas,

should be fitted to the gas supply pipe. Use only taps, regulator valves, connectors and

flexible hoses with the official mark of approval of the country of installation.

¾ CONNECT DIRECTLY TO THE THREADED END OF THE INLET

PIPE ISO 7-1.

1111

11

INSTALLATION:

"ELECTRICAL CONNECTION"ELECTRICAL CONNECTION

"ELECTRICAL CONNECTION

""

"

The mains electricity supply connected to the appliance should comply with the norms in

force in the country of installation.

Connection to the mains electricity supply should be through a socket with an earth terminal,

or through an intermediary switching device with a gap between contacts of at least 3 mm.

The power supply unit must be protected by appropriate fuses and use cables of a large

enough cross section to provide a normal supply to the appliance.

The hob is fitted with a power supply cable* which allow it to be connected only to a power

supply of 230 V between phases, or between phase and neutral.

• Connect to a 10/16 Amp socket. Before connecting, it is compulsory• Connect to a 10/16 Amp socket. Before connecting, it is compulsory

• Connect to a 10/16 Amp socket. Before connecting, it is compulsory

to check :to check :

to check :

. the power supply voltage shown on the electricity meter,

. the adjustment of the circuit breaker, and

. the fuse rating 10A.

Note : the socket must be reachable for any eventual repair. Take care of its location

at the time you install the hob.

Warning : before proceeding with the connection, check the continuity of theWarning : before proceeding with the connection, check the continuity of the

Warning : before proceeding with the connection, check the continuity of the

earthing of the power supply unit.earthing of the power supply unit.

earthing of the power supply unit.

We cannot be held responsible for any accident which has resulting from the useWe cannot be held responsible for any accident which has resulting from the use

We cannot be held responsible for any accident which has resulting from the use

of an appliance which is not connected to earth, or whose earthing is defective.of an appliance which is not connected to earth, or whose earthing is defective.

of an appliance which is not connected to earth, or whose earthing is defective.

* The eventual replacement of the supplying cord must be carried on by the After Sales

Service or by an agreed engineer, with a cord whose characteristics must be similar to the

original one : cord type H05 V2V2-F, 3 G 0,75 section.

1212

12

• SETTING THE IDLE FLAME

If you have changed the type of gas, it is important to verify the flame stability at the

minimum regulation.

"Gaining access to the by-pass screw"

To gain access to hob burner by-pass screws, remove the knobs from the control panel.

By-pass screw of the hob burner

Never loosen

the others screws !

REGULATING THE MINIMUM FLAME ON THE HOB BURNER

a) Natural gas :

. simply loosen the screw.

. switch on the burner and turn the knob to minimum.

. Turn the by-pass screw until a low flame is visible. Turn the control knob from

minimum to maximum position to check that it is satisfactory.

b) Butane-propane gas :

The by-pass screw should be screwed fully home, without being locked.

!

INSTALLATION:

"REGULATING THE FLAME""REGULATING THE FLAME"

"REGULATING THE FLAME"

1313

13

THE VERY FAST "DOUBLE RING" BURNER has a power rating of 3,2 kW :THE VERY FAST "DOUBLE RING" BURNER has a power rating of 3,2 kW :

THE VERY FAST "DOUBLE RING" BURNER has a power rating of 3,2 kW :

Use the large burner for bringing to the boil, for cooking large quantities, and generally for

all foods requiring rapid cooking.

THE FAST BURNER has a power rating of 2,5 kW :THE FAST BURNER has a power rating of 2,5 kW :

THE FAST BURNER has a power rating of 2,5 kW :

It is ideal for stewing, sauces and slow cooking.

THE SEMI-FAST BURNER has a power rating of 1,45 kW :THE SEMI-FAST BURNER has a power rating of 1,45 kW :

THE SEMI-FAST BURNER has a power rating of 1,45 kW :

Use this small burner for small pans.

For a proper use of the burners, choose pans which match the dimensions given below :

* Very fast* Very fast

* Very fast

Ø 18 cm and moreØ 18 cm and more

Ø 18 cm and more

* Fast* Fast

* Fast

Ø from 16 to 18 cmØ from 16 to 18 cm

Ø from 16 to 18 cm

* Semi-fast* Semi-fast

* Semi-fast

Ø 12 cmØ 12 cm

Ø 12 cm

On model fitted with cast iron pan supports,

we supply a reduction pan support to use pans with

dimensions of less than Ø 12 cm.

SOME TIPSSOME TIPS

SOME TIPS

.... ....

....

• Pans with curved, ridged or warped bottoms are not recommended.

• Avoid boiling food too intensely. Food is not cooked any more quickly this way. In fact,

it is subjected to severe agitation, which may cause the food to lose some of its flavour.

••

• To save gas, make sure that the flames do not overlap the bottom of the pan.

• Do not use the gas burner with an empty pan.

RECOMMENDATIONS : when the burners are not in service, the general gasRECOMMENDATIONS : when the burners are not in service, the general gas

RECOMMENDATIONS : when the burners are not in service, the general gas

supply tap should always be turned off.supply tap should always be turned off.

supply tap should always be turned off.

THE GAS BURNERTHE GAS BURNER

THE GAS BURNER

1414

14

Each burner is contolled by a tap with progressive settings allowing :

* a wider choice of settings from the maximum position to the lowest and most precise one,

* easier flame regulation according to the pan diameter,

* no risk of cutting off the flame or switching off when the flame is turned down quickly.

Each burner is fitted with automatic ignition. The ignition can be made with one hand, while

you have the pan in the other hand.

USE :USE :

USE :

• Turn on the gas tap,

••

• A symbol next to each control knob indicates which burner is lit.

Hob with automatic ignition integrated on the knob :

• Press and turn the knob until position

"High flame" "High flame"

"High flame" or

"+" "+"

"+" keeping it pressed

to produce sparks which in turn ignite the burner.

Hob with safety device on the burner and automatic ignition integrated on the

knob :

The thermocouple fast safety is a device allowing the automatic cut-out of the gas

supplying on the burner, in case the flame dies out accidentally.

• Press and turn the knob to position

"High flame" "High flame"

"High flame" or

"+" "+"

"+" keeping it pressed to

produce sparks which in turn ignite the burner. Keep the pressure on the control knob

a few seconds to permit the releasing of the safety device.

• Set the flame according to your cooking requirements.

Intermediate positions are available between the

"High flame" "High flame"

"High flame" or

"+" "+"

"+" and

"Low"Low

"Low

flame"flame"

flame" or

"-" "-"

"-" settings on the control knob.

• To turn the flame out, turn the control knob back to stop position.

Please note :

If there is a power cut, the burner can be ignited by pressing in and turning the knob

to position

"High flame"High flame

"High flame

""

" or

"+""+"

"+" and holding a naked flame to the burner.

THE GAS BURNERTHE GAS BURNER

THE GAS BURNER

1515

15

CLEANING

Before all cleaning or dismantling operation, it is imperative to :Before all cleaning or dismantling operation, it is imperative to :

Before all cleaning or dismantling operation, it is imperative to :

. disconnect the hob to the mains supply,. disconnect the hob to the mains supply,

. disconnect the hob to the mains supply,

. let all parts of the hob cool down. let all parts of the hob cool down

. let all parts of the hob cool down

..

.

Never useNever use

Never use

: :

:

harsh abrasives, scouring pads or sharp object to clean the hob. harsh abrasives, scouring pads or sharp object to clean the hob.

harsh abrasives, scouring pads or sharp object to clean the hob.

••

•

GENERAL MAINTENANCEGENERAL MAINTENANCE

GENERAL MAINTENANCE

THE HOB

. Enamelled steel hob : simply clean the enamelled hob with soapy water when the hob is

cold, rinse and wipe with a clean dry cloth. If you clean the enamelled hob when it is hot,

you may tarnish it.

. Stainless steel : clean with soapy water, rinse and dry. You can use a special product to

clean stainless steel which is available in stores.

THE KNOBSTHE KNOBS

THE KNOBS - For thorough cleaning, the control knobs can be removed by pulling them

upwards. Clean with soapy water, rinse and dry well before replacing.

THE GAS BURNERSTHE GAS BURNERS

THE GAS BURNERS

For cleaningFor cleaning

For cleaning, it is recommended to remove all greasy or burnt deposits with ammonia

based products or usual cleaning products.

• The burner cap : it is simply placed on the burner.

Remove the pan support, the burner cap and clean it with a slightly soapy sponge. Rinse

and dry.

The enamelled steel burner cap : do not immerse it in cold water when it is hot, this will

prevent the enamel cracking as a result of thermal shock.

• The burner body : regular cleaning will maintain the appliance original appearance.

Clean with a soapy sponge, rinse and dry. If the holes become clogged, brush the caps using

soapy water and dry with a clean cloth.

When re-assembling the burners, When re-assembling the burners,

When re-assembling the burners, make sure that the burner caps and the burners

themselves are dry and after, seat them correctly.

Be careful not to let any water get into the burners.Be careful not to let any water get into the burners.

Be careful not to let any water get into the burners.

THE PAN SUPPORTTHE PAN SUPPORT

THE PAN SUPPORT

Depending on the model, the pan supports are made of enamelled steel or cast-iron.

They are simply placed on the hob. Lift them up to remove them.

For the maintenance of the pan support, never use harsh abrasives, scouring pads or sharp

objects as this will cause irreparable damage to the enamel.

When the pan support is cold, simply clean with soapy water, rinse and dry with a clean

cloth.

1616

16

CANDY ELETTRODOMESTICI S.R.L.CANDY ELETTRODOMESTICI S.R.L.

CANDY ELETTRODOMESTICI S.R.L.

BRUGHERIO (MILANO)

ITALIA

Candy PA 640/2 X UK User manual

This manual is also suitable for

Candy PA 640/2 X UK User manual

Related papers

Other documents