ESAB L-TEC 160 Spool Adaptor Kit Assembly Instruction
- Type
- Assembly Instruction
F-12-989
October, 1997
ASSEMBLY INSTRUCTIONS FOR
L-TEC 160 SPOOL ADAPTOR KIT
(For 15-lb. Spool of .023-in. Wire)
In order to use the 15-lb. spool of .023 wire with the L-TEC
160, Spool Adaptor Kit P/N 17511 is required.
Assembly Instructions (see Figs. 1 & 2)
1. Mount the spool of wire so the recessed side of the
spool faces out and the wire is drawn from the bottom
of the spool. Be sure the stud on the spindle engages
the small round indentation in the spool, (see Fig. 1.)
2. Slide the spacer over the spindle.
3. Slide the hose clamp over the end of the spacer.
4. With the spindle stud still engaged all the way in the
indentation in the spool, push the spacer tightly against
the spool and tighten the hose clamp.
The above procedure is necessary to keep the spindle stud
engaged in the spool indentation. This will prevent the spool
from free wheeling, which can result in tangled wire.
F-12-989
October, 1997
ASSEMBLY INSTRUCTIONS FOR
L-TEC 160 SPOOL ADAPTOR KIT
(For 15-lb. Spool of .023-in. Wire)
In order to use the 15-lb. spool of .023 wire with the L-TEC
160, Spool Adaptor Kit P/N 17511 is required.
Assembly Instructions (see Figs. 1 & 2)
1. Mount the spool of wire so the recessed side of the
spool faces out and the wire is drawn from the bottom
of the spool. Be sure the stud on the spindle engages
the small round indentation in the spool, (see Fig. 1.)
2. Slide the spacer over the spindle.
3. Slide the hose clamp over the end of the spacer.
4. With the spindle stud still engaged all the way in the
indentation in the spool, push the spacer tightly against
the spool and tighten the hose clamp.
The above procedure is necessary to keep the spindle stud
engaged in the spool indentation. This will prevent the spool
from free wheeling, which can result in tangled wire.
F-12-989
October, 1997
ASSEMBLY INSTRUCTIONS FOR
L-TEC 160 SPOOL ADAPTOR KIT
(For 15-lb. Spool of .023-in. Wire)
In order to use the 15-lb. spool of .023 wire with the L-TEC
160, Spool Adaptor Kit P/N 17511 is required.
Assembly Instructions (see Figs. 1 & 2)
1. Mount the spool of wire so the recessed side of the
spool faces out and the wire is drawn from the bottom
of the spool. Be sure the stud on the spindle engages
the small round indentation in the spool, (see Fig. 1.)
2. Slide the spacer over the spindle.
3. Slide the hose clamp over the end of the spacer.
4. With the spindle stud still engaged all the way in the
indentation in the spool, push the spacer tightly against
the spool and tighten the hose clamp.
The above procedure is necessary to keep the spindle stud
engaged in the spool indentation. This will prevent the spool
from free wheeling, which can result in tangled wire.
F-12-989
October, 1997
ASSEMBLY INSTRUCTIONS FOR
L-TEC 160 SPOOL ADAPTOR KIT
(For 15-lb. Spool of .023-in. Wire)
In order to use the 15-lb. spool of .023 wire with the L-TEC
160, Spool Adaptor Kit P/N 17511 is required.
Assembly Instructions (see Figs. 1 & 2)
1. Mount the spool of wire so the recessed side of the
spool faces out and the wire is drawn from the bottom
of the spool. Be sure the stud on the spindle engages
the small round indentation in the spool, (see Fig. 1.)
2. Slide the spacer over the spindle.
3. Slide the hose clamp over the end of the spacer.
4. With the spindle stud still engaged all the way in the
indentation in the spool, push the spacer tightly against
the spool and tighten the hose clamp.
The above procedure is necessary to keep the spindle stud
engaged in the spool indentation. This will prevent the spool
from free wheeling, which can result in tangled wire.
F-12-989 10/97
F-12-989 10/97
F-12-989 10/97
F-12-989 10/97
Fig. 2 Spool Assembly
Fig. 1 Spindle
BE SURE THIS STUD ENGAGES THE
INDENTATION IN THE WIRE SPOOL.
RECESSED SIDE
SPINDLE
WELDING WIRE
(FROM BOTTOM OF SPOOL)
SPOOL ADAPTOR KIT
(SPACER & HOSE CLAMP)
Fig. 2 Spool Assembly
Fig. 1 Spindle
BE SURE THIS STUD ENGAGES THE
INDENTATION IN THE WIRE SPOOL.
RECESSED SIDE
SPINDLE
WELDING WIRE
(FROM BOTTOM OF SPOOL)
SPOOL ADAPTOR KIT
(SPACER & HOSE CLAMP)
Fig. 2 Spool Assembly
Fig. 1 Spindle
BE SURE THIS STUD ENGAGES THE
INDENTATION IN THE WIRE SPOOL.
RECESSED SIDE
SPINDLE
WELDING WIRE
(FROM BOTTOM OF SPOOL)
SPOOL ADAPTOR KIT
(SPACER & HOSE CLAMP)
Fig. 2 Spool Assembly
Fig. 1 Spindle
BE SURE THIS STUD ENGAGES THE
INDENTATION IN THE WIRE SPOOL.
RECESSED SIDE
SPINDLE
WELDING WIRE
(FROM BOTTOM OF SPOOL)
SPOOL ADAPTOR KIT
(SPACER & HOSE CLAMP)
-
1
-
2
ESAB L-TEC 160 Spool Adaptor Kit Assembly Instruction
- Type
- Assembly Instruction
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ESAB MIG-35 Solid/Cored Wire Feeder Troubleshooting instruction
-
-
ESAB LKA 180 User manual
-
-
-
-
ESAB Digipulse Dual Wire Feeder Bombardier Troubleshooting instruction
-
-
-
Other documents
-
Lincoln Electric SP150 Operating instructions
-
-
Toro 98958SL User manual
-
-
-
-
-
-
Eastwood MIG 250 Welder Operating instructions
-
Terex TS14G Maintenance Manual
