Industrial Multi Controller
MC-310B-DC355
User’s Manual
CONTEC CO.,LTD.
MC-310B-DC355
i
Check Your Package
Thank you for purchasing the CONTEC product.
The product consists of the items listed below.
Check, with the following list, that your package is complete. If you discover damaged or missing items,
contact your retailer.
Product Configuration List
- Unit [MC-310B-DC355]…1 - First step guide…1
- Communication connector…1 - External toothed screw (used with the earth terminal)…1
- The bracket fittings…2 - M3 screw (Use it for fixing bracket fittings.)…4
- Power connector…1 - Contact (For power connector)…4
- SD card holder…1 - Rubber feet…4
- Serial number label…1 - Warranty Certificate …1
C
N
2
S
W
C
N
3
S
D
R
S
T
1
2
-
2
4
V
D
C
C
N
1
L
1
L
2
L
3
P
O
W
ON *
3
4
2
1
XXXX
XXXXXX
XXX
XXXXXXX XXXXXX
x2
AK1550/10-3.5
U
nit
[MC-
310
B-D
C355]
Com
mun
ica
tio
n
co
nnec
tor
Power
connector
Rub
ber
fe
et M3 screw
Contact
External
t
oothed screw
x4
First step guide
SD card holder
x
4
Serial number
labe
l
Warr
anty Certificate
Warranty
Certificate
The brack
et
fitting
s
ii
MC-310B-DC355
About the handling of the battery and the storage battery in E U signatory
This symbol is specified in EU Directive 2006/66/EC, Article 20 "Information for end-users" and Annex II.
When discarding batteries and accumulators, the symbol above signifies that they must be sorted from normal
waste and disposed of. When element symbols are displayed below the above symbol, this signifies that the
batteries or accumulators contain heavy metals in a concentration above the standards.
The concentration standards are listed below.
Hg : hydrargyrum (0.0005%), Cd : cadmium (0.002%), Pb : lead (0.004%)
If these materials are not disposed of appropriately, there may be a serious impact on human health and the
global environment.
Note : This symbol is only valid in countries within the EU.
C
AUTI
ON
This product requires a separate power supply (12-24VDC±5%).
Be sure to use a power supply that meets this product’s power supply specification.
Copyright
Copyright 2012 CONTEC CO., LTD. ALL RIGHTS RESERVED.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document.
The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for results obtained by the user as a result of using this product.
Trademarks
Intel, Intel Atom, Intel Core and Celeron are registered trademarks of Intel Corporation. MS, Microsoft
and Windows are trademarks of Microsoft Corporation. Other brand and product names are trademarks
of their respective holder.
MC-310B-DC355
iii
Table of Contents
Copyright ............................................................................................................................................ ii
Trademarks .......................................................................................................................................... ii
Table of Contents ............................................................................................................................... iii
1. Introduction 1
About the Product ............................................................................................................................... 1
Features ........................................................................................................................................ 1
Accessories (Option) ................................................................................................................. 2
How to Use Accessories ............................................................................................................... 2
Customer Support................................................................................................................................ 3
Web Site ....................................................................................................................................... 3
How to Obtain Service ........................................................................................................................ 3
Liability ............................................................................................................................................... 3
Safety Precautions ............................................................................................................................... 4
Safety Information ....................................................................................................................... 4
Handling Precautions ................................................................................................................... 5
Environment ................................................................................................................................. 7
Inspection ..................................................................................................................................... 7
Storage ......................................................................................................................................... 7
Disposal ........................................................................................................................................ 7
2. Each Component Function 9
Component Name ................................................................................................................................ 9
Component Function ......................................................................................................................... 10
(1) LAN port .............................................................................................................................. 10
(2) DVI-D ................................................................................................................................... 10
(3) Reset SW .............................................................................................................................. 10
4) USB port ................................................................................................................................ 11
(5) Power connector (12-24VDC IN) ......................................................................................... 11
(6) Ground terminal .................................................................................................................... 11
(7) Speaker connecting terminal ................................................................................................ 11
(8) SD slot .................................................................................................................................. 12
(9) USB port (miniB) ................................................................................................................. 12
(10) DIP SW ............................................................................................................................... 13
(11) Communication connector .................................................................................................. 13
(12) External extended connector .............................................................................................. 15
LED ................................................................................................................................................... 19
LED Display ............................................................................................................................... 19
iv
MC-310B-DC355
3. Setup 21
Before Using the Product for the First Time ..................................................................................... 21
Hardware Setup ................................................................................................................................. 21
Method for Power Supply .......................................................................................................... 21
Method for Installation ............................................................................................................... 21
Distances between this product and its vicinity ......................................................................... 22
Software Setup .................................................................................................................................. 22
4. Specification 23
Specification ...................................................................................................................................... 23
Hardware or Factory Setting ...................................................................................................... 23
Functional Specification ............................................................................................................. 24
Installation Environment Requirements ..................................................................................... 25
Physical dimensions ................................................................................................................... 25
Battery ............................................................................................................................................... 26
Battery Specification .................................................................................................................. 26
Removing the battery ................................................................................................................. 26
Disposing the battery .................................................................................................................. 26
1. Introduction
MC-310B-DC355
1
1.
Introduction
This chapter provides information you should know before using the product.
About the Product
This product is an industrial use, multi controller with diverse uses.
It contains a 600 MHz ARM processor(T.I. Cortex-A8) and 256 MB of DDR2 SDRAM, and is a
platform for the execution of open source applications.
In addition, this product makes use of SD cards, which have excellent cost performance, and it also
supports high-speed and high-capacity SDHC cards as the startup device.
It is equipped with a variety of extension I/O features such as those for display output, analog input,
digital I/O, audio output, LAN, USB2.0, etc.
This product is the best choice for applications which require a greater space-saving and power-saving
controller than the PC.
Features
Powerful execution platform supporting fanless operation
It is a powerful general-purpose execution platform for open source applications equipped with SoC
“AM3517” that incorporates a 600MHz ARM processor (T.I. Cortex-A8) and system memory of
256MB.
Equipped with Linux OS
With Linux OS (Kernel 2.6), it allows users to freely develop applications for diversified fields using
vast amounts of open source resources.
Equipped with a variety of extension I/O features
The product is equipped with an array of extension I/Os including display out, 4-channel analog input
(AI), digital I/O (DIO) of 4 inputs and outputs each, audio output, LAN, and USB2.0.
- Display output : 1280 x 720(720p), 1024 x 768(XGA), 800 x 600(SVGA), 640 x 480(VGA)
- Analog input : Equipped with single-ended input, input range
±
5V, Resolution 12 bit
- Digital input : Equipped with opto-coupler isolated input (for current sink output)
- Digital output : Equipped with opto-coupler isolated open collector output (current sink type)
1. Introduction
2
MC-310B-DC355
Accessories (Option)
Cable & Connector
Flat Cable with Two 37-pin D- SUB Connectors : PCB37P-1.5 (1.5m)
: PCB37P-3 (3m)
: PCB37P-5 (5m)
Shielded Cable with Two 37-pin D-Type Connectors : PCB37PS-0.5P (0.5m)
: PCB37PS-1.5P (1.5m)
: PCB37PS-3P (3m)
: PCB37PS-5P (5m)
Flat Cable with One 37-pin D-Type Connector : PCA37P-1.5 (1.5m)
: PCA37P-3 (3m)
: PCA37P-5 (5m)
Shielded Cable with One 37-pin D-Type Connector : PCA37PS-0.5P (0.5m)
: PCA37PS-1.5P (1.5m)
: PCA37PS-3P (3m)
: PCA37PS-5P (5m)
D-SUB37P Male Connector Set (5pieses) : CN5-D37M
Terminal Unit / Power Supply
Screw Terminal Unit (M3 x 37P) : EPD-37A *1*2
Screw Terminal Unit (M3.5 x 37P) : EPD-37 *1
General Purpose Terminal (M3 x 37P) : DTP-3C *1
Screw Terminal (M2.5 x 37P) : DTP-4C *1
AC Adapter (Input : 90 - 264VAC, Output : 12VDC 3.75A) : IPC-ACAP12-04L
*1
A PCB37P or PCB37PS optional cable is required separately.
*2 “
Screw upright terminal panel” is used to prevent terminal screws from falling off.
*
Check the CONTEC’s Web site for more information on these options.
How to Use Accessories
For more information on image output, Line out and software setup, visit the resource center
( http://www.contec.co.jp/mc ).
1. Introduction
MC-310B-DC355
3
Customer Support
CONTEC provides the following support services for you to use CONTEC products more efficiently
and comfortably.
The latest driver for your controller is available on our home page. Download it for your use. Our
home page also includes documents useful for product operation such as operating precautions. Visit
our website before getting started using the product.
Web Site
https://www.contec.com/
Latest product information
CONTEC provides up-to-date information on products.
CONTEC also provides product manuals and various technical documents in the PDF.
Free download
You can download updated driver software and differential files as well as sample programs available in
several languages.
Note! For product information
Contact your retailer if you have any technical question about a CONTEC product or need its price,
delivery time, or estimate information.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor
be liable for any incidental or consequential damages due to such defect or consequences that arise from
inexperienced usage, misuse, or malfunction of this device.
How to Use Accessories
For more information on this product, visit the resource center ( http://www.contec.co.jp/mc ).
1. Introduction
4
MC-310B-DC355
Safety Precautions
Understand the following definitions and precautions to use the product safely.
Safety Information
This document provides safety information using the following symbols to prevent accidents resulting
in injury or death and the destruction of equipment and resources. Understand the meanings of these
labels to operate the equipment safely.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury or in property damage.
1. Introduction
MC-310B-DC355
5
Handling Precautions
DANGER
- Do not use the product where it may be exposed to flammable or corrosive gas. Doing so may result
in an explosion, fire, electric shock, or failure.
- Do not put or insert metallic substances such as wire rods into USB ports or the SD slot on the
product.
Doing so may result in fire, electric shock, or failure.
CAUTION
- Do not use or store the product in a location exposed to extremely high or low temperature or
susceptible to rapid temperature changes.
Example: - Exposure to direct sun
- In the vicinity of a heat source
- Do not use the product in extremely humid or dusty locations. It is extremely dangerous to use the
product with its interior penetrated by water or any other fluid or conductive dust. If the product
must be used in such an environment, install it on a dust-proof control panel, for example.
- Avoid using or storing the device in locations subject to shock or vibration.
- Do not use or store the product in the vicinity of devices that generate strong magnetic force or
electric waves. Doing so may cause malfunctions (freeze or reboot).
- Do not use or store the product in the presence of chemicals.
- Before inserting/removing an SD card or plugging/unplugging connectors or cables, be sure to
unplug the power cable.
- Do not modify this product. CONTEC will bear no responsibility for any problems or issues
resulting from the modification of this product.
- In the event of failure or abnormality (foul smells or excessive heat generation), unplug the power
cable immediately and contact your retailer.
- To connect with peripherals, use a grounded, shielded cable.
- To clean this product, wipe it gently with a soft cloth dampened with either water or mild detergent.
To prevent peeling or discoloration of paint, do not use chemicals or volatile solvents, such as
benzene or paint thinner.
- Component Life :
Battery-------The internal calendar clock is backed by a Lithium primary battery.
The backup time at a temperature of 25°C with the power disconnected is 10 years or
more.
Contact your retailer about replacing a battery.
* Replacement of expendables is handled as a repair (there will be a charge).
- When connecting cables, first check the shapes of connectors (such as USB connectors), and then
insert them in the correct orientation. After they are connected, do not put too much load on the
connected part. Doing so may result in poor contact or damage to this product and the connected
part.
1. Introduction
6
MC-310B-DC355
- Do not touch these product's metal plated terminals with your hands.
Otherwise, this product may malfunction, overheat, or cause a failure.
- It may cause a trouble in recognizing and operating the device according to the kind of USB hub.
If you use the USB hub, we encourage you to take advantage of the CONTEC’s product loan
service to confirm operation before purchasing.
- The specification of this product is subject to change without notice for enhancement and quality
improvement. Even when using this product continuously, be sure to read the manual of contec’s
website and understand the contents.
- Be sure to attach the setup guide to it if handing over this product.
- As for the product with a D-SUB connector, the appropriate tightening torque for the cable
connector is less than 2 kgf
･
cm.
- Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever
(including damages for loss of business profits) arising out of the use or inability to use this
CONTEC product or the information contained herein.
FCC PART 15 Class A Notice
T
h
is
eq
ui
p
me
n
t
ha
s
b
e
en
t
e
st
ed
an
d
f
ou
nd
to
co
mp
l
y
wi
t
h
th
e
l
i
mi
ts
fo
r
a
C
l
as
s
A
d
i
gi
ta
l
d
ev
i
ce
,
p
u
rs
u
an
t
t
o
p
a
r
t
1
5
of
th
e
F
CC
Ru
le
s
.
Th
e
se
l
i
mi
t
s
ar
e
d
es
i
gn
ed
to
pr
ov
i
de
r
e
a
s
on
a
bl
e
p
ro
te
c
ti
on
against harmful
in
ter
ference when the equipment is operated in commercial
en
vironment.
This equipme
nt g
ene
rat
es, uses, and can radiate radio frequency energy an
d, i
f n
ot
installed and
used in accorda
nce
wi
th
the instruction manual, may cause harmful interf
ere
nce
to
rad
io
communication
s.
Oper
ati
on
of this equipment in a residential area is likel
y to
ca
use
har
mful
interference a
t h
is
own
exp
ens
e.
N
OT
E
Change or modi
fica
tio
ns
not
exp
res
sly
approved the manufacturer can vo
id
the
us
er's
au
tho
rit
y to
op
erat
e t
his
equ
ipm
ent
.
WARNING TO USE
R
1. Introduction
MC-310B-DC355
7
Environment
Use this product in the following environment. If used in an unauthorized environment, the board may
overheat, malfunction, or cause a failure.
Operating temperature
0 - 50°C
Operating humidity
10 - 90%RH (No condensation)
Corrosive gases
None
Floating dust particles
Not to be excessive
Inspection
Inspect the product periodically as follows to use it safely.
- Connect
the
ca
ble
and
co
nne
cto
r co
rrectly.
C
N2 SW CN
3
S
D
RST
12
- 24
VDC
CN1
L1 L
2 L3
POW
Storage
When storing this product, keep it in its original packing form.
(1) Put the product in the storage bag.
(2) Wrap it in the packing material, then put it in the box.
(3) Store the package at room temperature at a place free from direct sunlight, moisture, shock,
vibration, magnetism, and static electricity.
Disposal
When disposing of the product, follow the disposal procedures stipulated under the relevant laws and
municipal ordinances.
* This product is backed by a Lithium primary battery, so please be careful about its disposal.
* For more information on removing a battery, see "Removing the battery" in chapter 4.
1. Introduction
8
MC-310B-DC355
2. Each Component Function
MC-310B-DC355
9
2.
Each Component Function
Component Name
Component name is shown in the following figure 2.1.
L1 L
2 L3
POW
(5)
(4)
(2)
(1)
(3)
(6
) (7)
(8)
(9)
(10
) (11
)
(12)
(1)
LAN port (2) DVI-D (3)
Reset switch (4) USB port
(5)
Power supply
connector
(6) Ground terminal (7)
Line out (8) SD slot
(9)
USB port
(miniB)
(10)
DIP switch
(11)
Communication
connector
(12)
External extended
connector
Figure 2.1. Component Name
(1) LAN port: Connector for LAN (100BASE-TX).
(2) DVI-D: Connector for display.
The image output please refers to resource center (http://www.contec.co.jp/mc).
(3) Reset switch: Used to reset this product.
(4) USB port: Accepts USB flash drives and similar storage devices for saving data. Do not use during
operation in environments with a lot of electromagnetic interference.
(5) Power supply connector: Accepts the power connector. Supports AWG 24 - 18 cables.
(6) Ground terminal: Used to connect the earth cable.
(7) Line out: Connector for Line out.
(8) SD slot: Accepts SD cards for data storage and similar purposes.
(9) USB port (miniB): Connects to a host to act as a debug console. Do not use during operation in
environments with a lot of electromagnetic interference.
(10) DIP switch: Can be used to acquire setting status from an application.
Used to select the startup device.
(11) Communication connector: Accepts the communication connector. Supports AWG 28 - 16 cables.
(12) External extended connector: This is the external I/O (four analog inputs, four digital inputs, and
four digital outputs) connector. Supports AWG 28 - 16 cables.
2. Each Component Function
10
MC-310B-DC355
Component Function
(1) LAN port
Connector for LAN(100BASE-TX)
Pin No.
Signal name
Contents
1
TX+
Transmitting Data (+) Output
2
TX1
Transmitting Data (-) Output
3
RX+
Receiving Data (+) Input
4
N.C.
Not connected
5
N.C.
Not connected
6
RX-
Receiving Data (-) Input
7
N.C.
Not connected
8
N.C.
Not connected
(2) DVI-D
It is a connector for display connection.
The screen resolutions supported by this product are 1280 x 720(720p), 1024 x 786(XGA), 800 x
600(SVGA), and 640 x 480(VGA).
For more information on image output, visit the resource center (http://www.contec.co.jp/mc).
Pin No.
Signal name
Pin No.
Signal name
1
DATA2-
13
N.C.
2
DATA2+
14
+5V
3
GND
15
GND
4
N.C.
16
N.C.
5
N.C.
17
DATA0-
6
N.C.
18
DATA0+
7
N.C.
19
GND
8
N.C.
20
N.C.
9
DATA1-
21
N.C.
10
DATA1+
22
GND
11
GND
23
CLK+
12
N.C.
24
CLK-
(3) Reset SW
Reset this product.
2. Each Component Function
MC-310B-DC355
11
4) USB port
The controller has 2 interface ports compatible with USB2.0 (High/Full/Low Speed).
You can save data by plugging a USB flash drive into the port. Do not use a USB flash memory while
the controller is being operated in an environment where the noise level is high.
The power supply capacity of the USB port is 500mA. When connecting a USB device that draws
high current to this product, check its AMP draw so that the power supply capacity of the power supply
unit will not be exceeded.
Pin No.
Signal name
1
Vcc
2
DATA+
3
DATA-
4
GND
CAUTION
It may cause a trouble in recognizing and operating the device according to the kind of USB hub.
If you use the USB hub, we encourage you to take advantage of the CONTEC’s product loan
service to confirm operation before purchasing.
(5) Power connector (12-24VDC IN)
Use the recommended power supply (IPC-ACAP12-04L) or the connector provided with the product.
The applicable cable is AWG24-18.
Pin No.
Signal name
1
GND
2
GND
3
12-24VDC
4
12-24VDC
(6) Ground terminal
Connect a ground wire using the outer toothed screw provided with the product.
(7) Speaker connecting terminal
It is a connector for line output.
For more information on output, visit the resource center (http://www.contec.co.jp/mc).
2. Each Component Function
12
MC-310B-DC355
(8) SD slot
Insert the SD card and use it for storing data.
C
N
2
S
W
C
N
3
S
D
R
S
T
1
2
-
2
4
V
D
C
C
N
1
L
1
L
2
L
3
P
O
W
ON *
3
4
2
1
Figure 2.2. Inserting SD slot
Mounting the SD card holder provided with the product prevents the card from coming off.
Loosen one screw.
Slide the metal fitting into a space between the metal sheet and the screw.
C
N
2
S
W
C
N
3
S
D
R
S
T
1
2
-
2
4
V
D
C
C
N
1
L
1
L
2
L
3
P
O
W
ON *
3
4
2
1
C
N
2
S
W
C
N
3
S
D
R
S
T
1
2
-
2
4
V
D
C
C
N
1
L
1
L
2
L
3
P
O
W
ON *
3
4
2
1
Tighten the screw to secure
the metal fitting.
Figure 2.3. How to mount the SD card holder
(9) USB port (miniB)
When connected to the host, it works as a debug console. Do not use it while the controller is being
operated in an environment where the noise level is high.
Pin No.
Signal name
1
VBUS
2
-Data (D-)
3
+Data (D+)
4
ID (NC)
5
GND
2. Each Component Function
MC-310B-DC355
13
(10) DIP SW
1 - 3 : It is a general-purpose DIP switch.
This switch allows for the acquisition of settings from the application.
4 : Use it for choosing device boot.
SW No.
Operation
Contents
1 -
It is a general-porpose switch.
This switch allows for the acquisition of settings from the application.
2 -
It is a general-porpose switch.
This switch allows for the acquisition of settings from the application.
3 -
It is a general-porpose switch.
This switch allows for the acquisition of settings from the application.
4
ON
When booting from the SD card, turn it ON.
OFF
Default. When booting with the built-in NAND Flash ROM, turn it ON.
(11) Communication connector
RS-422/RS-485 communication (x 2 ports) are provided. Use the attached communication connector.
The applicable cable is AWG28-16.
Pin No.
Signal name
Pin No.
Signal name
1
TXD0+
6
TXD1+
2
TXD0-
7
TXD1-
3
RXD0+
8
RXD1+
4
RXD0-
9
RXD1-
5
GND
10
GND
The data transfer mode setting switch is used to switch between full duplex and half duplex. Set the
appropriate data transfer mode for the device with which you are communicating. Bits 1 to 6 are used
to set the data transfer mode. SW1 corresponds to Port 0 and SW2 to Port 1. The default is “half
duplex”.
Transmission
mode
Half-duplex [Half]
< Initial value >
Full duplex [Full]
When there are no RTS and CTS
RTS
CTS
Setting
TXD is only used for data transmission ; the
sending and receiving modes should be switched
over using the modem control register.
With above setting, RTS and CTS are connected in
this product.
Communication is available without wiring of RTS
and CTS.
2. Each Component Function
14
MC-310B-DC355
CAUTION
Do not use with bits 1 and 2 both set ON as this may result in damage to this product.
Setting of Terminator
The terminator setting switch controls whether or not a terminator is inserted into each signal line. Set
the terminators on or off in accordance with the devices with which you are communicating. The
terminators on the module are 100
Ω
resistors.
Each bit in the switch corresponds to a different signal line: bit 7 for RxD, bit 8 for CTS, bit 9 for TxD,
and bit 10 for RTS.
If you wish to use a terminator of other than 100
Ω
, set the terminator switch OFF and insert an external
terminator. The following examples show the status when terminators are inserted/not inserted for
half-duplex and full duplex settings respectively.
Not inserted
Factory
setting
- Half duplex
(A
)
(B)
(C) (D
)
[ ]
[
A
or
D
]
10
9
87
6
5
4
321
ON
109
87
6
5
4
321
ON
109
87
6
5
4
321
ON
RTS
TxD
CT
S
R
xD
R
TS
T
xD
C
TS
RxD
RTS
TxD
CTS
RxD
Terminator
(
bit
9)
Terminator
(bit
9)
Inserted
Not Inserted
Not
In
ser
ted
B
or
C
Figure 2.4. Party Line Connection
2. Each Component Function
MC-310B-DC355
15
- Full duplex
TxD
RxD
RxD
TxD
ON
109
87
6
5
4
32
1
ON
RTS
TxD
CTS
RxD
RTS
TxD
CTS
RxD
10
9
87
6
5
4
3
21
Not Inserted
Turn RTS and CTS terminator off.
Inserted
Terminator
(bit 9)
Terminator
(bit 7)
Figure 2.5. Example Connection Oneself loop to RTS and CTS
For instructions on how to remove the housing, see “Removing the battery” in Chapter 4.
Figure 2.6. Location of SW1, SW2
(12) External extended connector
It is a connector for external I/O.
Pin No.
Signal name
Pin No.
Signal name
Pin No.
Signal name
Pin No.
Signal name
1
DI COM
11
DO COM-
21
N.C.
31
N.C.
2
DI 00
12
N.C.
22
N.C.
32
AI GND
3
DI 01
13
N.C.
23
N.C.
33
AI GND
4
DI 02
14
AI GND
24
N.C.
34
AI GND
5
DI 03
15
AI 00
25
N.C.
35
AI GND
6
DO COM+
16
AI 01
26
N.C.
36
AI GND
7
DO 00
17
AI 02
27
N.C.
37
AI GND
8
DO 01
18
AI 03
28
N.C.
9
DO 02
19
AI GND
29
N.C.
10
DO 03
20
N.C.
30
N.C.
COM+/- : 12 - 24VDC
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec SPF14SQ1700 NEW Owner's manual
-
-
-
-
Contec PT-310LS Owner's manual
-
-
-
-
-