Page is loading ...
VALORE SEVEN
Pacific)
Version No.:V1.20161222
Serial Number
• (H) 26.49" x (W) 8.26" x (D) 8.85"
• Hand shower hose: 59.05"
• Weight: Net: 10 lbs /Gross: 12 lbs
5
1
8
"
7
19
8
"
7
24
8
"
1
7
8
"
1
26
2
"
3
2
8
"
3
4
4
"
9
"
1
2
8
"
• Optional drill-less design and installs in under
one hour
• Sleek, slim contemporary design
• Large embedded body jet
• 50-silicone nozzle"rainfall" shower head
• German engineered diverter with 6 distinct spray
modes
• Full brass hand shower and cradle
• Compatibe with most shower stalls and tub/shower
enclosures
• High quality metal components
BEFORE USAGE
• Read this Installation and User Guide before
installing and operating.
• Always take extra care when installing to prevent
injury. Wear appropriate safety equipment.
• Do not allow children unsupervised use of the
shower panel.
• Do not use the shower panel if you are physically
impaired or under the influence of
alcohol or any substance which may prevent you
from properly operating the shower panel.
• Keep enough distance between yourself and the
shower panel.
• Do not allow sensitive parts of the body such as
eyes to come too close to the shower jets.
• Proper pressure balance needs to be maintained
between hot and cold water inputs to prevent
scalding or injury.
- 2 -
BEFORE INSTALLATION
• Before and during installation, read and familiarize yourself with all installation instructions for this product.
• Keep all components, parts and accessories of this product away from small children and minors. During
installation, all screws, tools and small parts should be supervised so that they do not fall into the hands of children.
• Use caution at all times when installing this product. Ensure that you are physically able to perform all parts of the
installation and that you have the correct tools and equipment needed.
• Before beginning,remove all wrappers and packinging materials including staples and packing straps.
• Check to ensure that all components and parts are complete.
• The Filter Gasket (#10) must be installed to protect against incoming dirt by pipework. Incoming dirt can impair the
function and/or lead to damages on functional parts of the fixture. Manufacturer will not be held liable for resulting
damages.
• The O Ring Gasket (# 24) must be installed to prevent water leakage. Manufacturer will not be responsible or liable
from any damage which results directly or indirectly from failure to installation of the O Ring Gasket.
Sealing Tape Silicone
Pencil
Shear
- 3 -
17
18
19
20
21
22
23
24
25
26
27
28
Description
Bottom Shower Panel Casing
Top Shower Panel Casing
Shower Head
Ring Clamp
White Top Hose
Screws
Top Cover
Shower Head Outlet Connector Cover
Elbow Connector
Filter Gasket
Brass Extender Joint (1-7/8"&2-3/4"x1/2")
Flow Regulator
Base Plate Cover with Tape ( for Shower Head Outlet Connector Cover)
Gray Main PVC Supply Line
Screws
Nut
Brass Nut
Rubber Washer( 1-1/2")
Screws
Screw Anchor
Positioning and Support Brackets
Full Brass Handshower
Handshower Hose
O Ring Gasket
Handshower Cradle Assembly
Jet
Diverter Knob
Diverter Valve
Qty
1 Set
1 Set
1 Pc
2 Pcs
1 Pc
6 Psc
1 Pc
1 Pc
1 Pc
2 Pcs
2 Pcs
1 Pc
1 Pc
1 Pc
4 Pcs
4 Pcs
2 Pcs
2 Pcs
2 Pcs
2 Pcs
1 Pc
1 Pc
1 Set
2 Pcs
1 Pc
1 Pc
1 Pc
1 Pc
- 4 -
9-2
5
1
3
4
2
5
6
7
8
9
10
11
13
12
4
14
15
17
18
19
20
21
22
10
23
24
25
24
17
18
28
27
26
10
24
17
- 5 -
16
HAND SHOWER AND CRADLE ASSEMBLY
a
b
7
23
24
22
10
- 6 -
1
25
25
25
25
17
24
17
25
18
TOP COVER ASSEMBLY
e
g
h
I
- 7 -
15
16
f
Note: The hose connecting
the shower head is in white
color.
4
5
2
6
7
PH
+
PH
+
PH
+
• Before Installation, ensure there is sufficient
clearance to accommodate the shower panel.
A minimum of 12.5" is required between the
shower outlet and top of your existing valve.
Ensure that the water line to the overhead
shower pipe is completely shut off prior to
performing any work.
• Remove your existing shower head.Then
remove your existing shower arm
• Two brass extender joints (Part #11) are included
with this shower panel.
Test both extender joints to see which joint will
provide you a minimum of 5/8'' from the wall.
• Use the plumbing tape and wrap the threaded
part of the brass extender joint (Part #11) on
both ends.
• Place the flow regulator (Part #12) into the
appropriate extender joint (Part #11), ensure the
flow regulator's direction is right as diagram 4
indicating, ensure the longer end of threading
on the extender joint is facing outward.
Note: The flow regulator (Part #12) is required
to be installed as some states in the U.S.
require a flow rate of 2.0GPM . You can
choose to install the flow regulator based on
the requirements of state or local plumbing
codes.
INSTALLATION INSTRUCTIONS
- 7 -
Min 12.5Inch
3
4
11
MAX
5/
8"
½" diameter is needed to
accommodate the shower panel's
Brass Extender Joint (Part #11)
Flow Regulator
11
12
- 8 -
INSTALLATION INSTRUCTIONS
When the overhead shower outlet is located outside shower surface, use the Method 1 (Drilled installation).
When the overhead shower outlet is located inside the shower surface, use the Method 2 (Drill-less installation).
Method 1: Drilled installation instructions
1. Place shower panel against the wall in its desird permanent location.
2. Mark Line 1 ane Line 2:
- Mark the bottom of the panel with a pencil or erasable marker.(Line 1)
- Mark a second line (Line 2) which 9.86 inch is above and parallel to Line 1.
- Place the bottom of the mounting bracket flush against Line 2 and hold flat against the shower surface.
Recommended 10"
Shower outlet
- 9 -
Bracket installation options:
9.86"
Line 2
Line 1
H
M
L
Shower outlet
H
M
L
Level
1
2
3
4. Using a pencil or erassable market, mark drill holes A and B.
3. To ensure the bracket will be in a straight abd level position, use a level tool against the side of the bracket to make fine
adjustments to the bracket position until fully level.
H
M
L
4
Bracket
21
21
21
B
A
B
A
5. Drill the 2 screw holes with a
6mm bit suitable for the wall
surface.
6. Install the anchors(Part #20),
Seal the wall around the nipple
and the anchors with waterproof
silicone.
.
7. After anchor screws have been
installed, affix the Positioning &
Support Brackets (Part #21) using
supplied Screws (Part #19).
Silicone
B
A
21
20 x2PCS
1 9 x2PCS
Note: Before drilling make sure you have the correct drill bit for your shower surface.
8. Hose shearing instructions
a. Grasping the PVC supply line, extend the PVC supply line straight over the shower head outlet.
b. Mark the PVC supply line where it intersects the bottom of the shower head outlet.
c. Shear the excess PVC supply line at the mark.
INSTALLATION INSTRUCTIONS
PH
+
Method 1
- 10 -
Warning: Ensure your shower water
line is not directly behind the drilling
points A and B. Drilling into the water
supply line may cause extensive
damage.
Shear
a
b
c
Line 1
14
4
4
9
PH
+
a
b
c
9.Connecting the Supply Line Elbow (Part #9)
to the main PVC Supply Line (Part #14):
a. Insert the Ring Clamp (Part #4) onto the end
of Gray PVC Supply Line (Part #14).
b. Fully insert the grooved end of the Elbow
Connector (Part #9) into the Gray PVC Supply
Line (Part #14).
c. With a Phillips head screwdriver, tighten the
bolt and nut on the Hose Clamp (Part #4) until
the Gray PVC Supply Line is secured to Elbow
Connector (Part #9).
d. The Elbow Connector (Part #9) will be secured
to the Brass Extender Joint (Part #11) in a later
step.
10. Install the PVC cover.
a. Peel off the paper backing to the adhesive ring
for the Base Plate cover (Part #13).
(Note: Clear all residues to ensure the cover will
bond properly)
b. Place the adhesive side to the wall and apply
pressure to secure the Base Plate Cover
(Part #13).
c. Add a Filter Gasket (Part #10) into Elbow Joint
(Part #9) first.Then attach the Elbow Joint (Part #9)
to the Brass Extender Joint (Part #11), turn clock
wise to tighten.
d. Place the Showerhead Cover (Part #8) to
conceal plumbing fixture.
a
b
d
14
14
4
9
4
9
11
13
13
11
10
9
14
8
14
INSTALLATION INSTRUCTIONS
- 11 -
c
INSTALLATION INSTRUCTIONS
- 12 -
11. Install the shower panel:
After all connections have been completed
inside the shower panel, it is ready to be
hung on the shower wall for installation.
a. Place the shower panel on the desired bracket
position you previously selected.
b. Raise the shower panel and rest it againg the
bracket until the support strut is resting sungly
in the desired bracket position.
c.Once a snug and secure fit is achieved and all
parts of the PVC Supply Line are secured to the
back of the shower panel, verify that water is
flowing normally prior to sealing the panel.
Sealant may be applied to seal the gap between
the shower panel boby and the wall to prevent
water from entering behind the shower panel.
Silicone
21
• Insert the Bracket (Part #21) onto the Brass
Extender Joint (Part #11)
11
• To ensure the bracket will be in straight
and level position, use a level tool against
the side of the bracket make fine adjustments
to the bracket position until fully level.
• Once fully level, this will be the final position of
the bracket guide.
• Take a pencil/marker and lightly mark the vertical
position of the Bracket (Part #21).
Method 2: Drill-less Installation Instruction
21
21
1. Place the Bracket (Part #21)
• Peel off the paper backing to the adhesive on the
back side of the Bracket (Part #21).
• Place the adhesive side to the wall and apply
pressure to secure the Bracket(Part #21).
• Place the Rubber Washer (Part #18) and nut (Part #17)
over the Brass Extender Joint (Part #11), and tighten
the nut to secure the bracket (Part #21) to the extender
joint.
a
b
c
H
M
L
2. Shear the Gray PVC Supply Line (Part #14)
Installation position will vary, depending on your shower space clearance.
If you install(H,M,L):
▪ H - shear 18.58" length of the Gray PVC Supply Line.
▪ M - shear 15.2" length of the Gray PVC Supply Line.
▪ L - shear 11.81" length of the Gray PVC Supply Line.
There are 3 positions in the bracket: High, Medium, Low.
Depending on which position you choose; you will need the Shear excess gray PVC Supply Line.
18.58"
Shear
21
21
21
11
17
18
Note: Prior to applying bracket clean all residues from the wall bond properly. Recommend to use, cider vinegar,
alcohol, or mineral dissolve.
INSTALLATION INSTRUCTIONS
H
15.2"
M
11.81"
L
Recommended
10"
- 13 -
3
INSTALLATION INSTRUCTIONS
4. Install the shower panel.
After all connections have been completed
inside the shower panel, it is ready to be
hung on the shower wall for installation.
b. Place the shower panel on the desired bracket
position you previously selected.
c. Raise the shower panel and rest it against the
bracket until the support strut is resting snugly
in the desired bracket position.
d. Once a snug and secure fit is achieved and all
parts of the PVC Supply Line are secured to the
back of the shower panel, verify that water is
flowing normally prior to sealing the panel.
Sealant may be applied to seal the gap between
the shower panel boby and the wall to prevent
water from entering behind the shower panel.
6
10
a. Add a Filter Gasket (Part #10) into Elbow Joint
(Part #9) first.Then attach the Elbow Joint (Part #9)
to the Brass Extender Joint (Part #11), turn clock
wise to tighten.
- 14 -
14
4
4
9
PH
+
a
b
c
14
4
9
14
5
3.Connecting the Supply Line Elbow (Part #9)
to the main PVC Supply Line (Part #14):
a. Insert the Ring Clamp (Part #4) onto the end
of Gray PVC Supply Line (Part #14).
b. Fully insert the grooved end of the Elbow
Connector (Part #9) into the Gray PVC Supply
Line (Part #14).
c. With a Phillips head screwdriver, tighten the
bolt and nut on the Hose Clamp (Part #4) until
the Gray PVC Supply Line is secured to Elbow
Connector (Part #9).
d. The Elbow Connector (Part #9) will be secured
to the Brass Extender Joint (Part #11) in a later
step.
9
14
4
11
9
14
Silicone
21
d
80
80
20-80 psi
0
• Jet Spray Position
• Dual Spray Modes
- 15 -
a
b
c
When the selector knob is placed in between two
operating, this will result in a to simultaneous
operation of both adjustment spray modes. A slight
reduction in water pressure may occur due to the
shared water flow between the two spray modes.
When the position knob is placed in “d”, the
handshower and the top hydro jets will work
simultaneously.
Diverter Valve Structure
How to Remove the Diverter Valve
• Remove the cover (Part #3) to open the set screw
access hole.
1
• Loosen the set screw (Part #1) from the valve stem and
pull the knob (Part #2) straight out.
2
(2.5 mm)
3
2
1
• Loosen and remove the gland nut (Part #4).
4
4
3
- 16 -
4
5
1
2
3
3
1
• Remove the Diverter valve (Part #5) by pulling it straight
out.
5
Diverter valve
4
(2.5 mm)
2
1
1
Diverter valve
1
How to Install the Diverter Valve
3
Adjust the knob with right position
2
• Place the knob (Part #2) on the valve stem.
• Before securing the knob, turn on the water to know
which way the handle is to be pointed.
5
4
• Place the cover (Part #3) and finish the install.• Once the correct position of the knob has been
determined, place the knob on the valve stem and
tighten the set screw (Part #1). Do not overtighten.
5
Diverter valve
• Place the Diverter valve (Part #5) into the valve body.
Note the one pillar on the bottom of the Diverter valve
(Part#5) must be aligned with the hole in the rear of the
body.
2
4
2
• Tighten the gland nut (Part #4). Take precaution to avoid
scratching the trim plate. Do not force the nut too tightly.
4
(2.5 mm)
2
1
1
3
3
Shower Head Mode
- 17 -
• Loosen the nut securing the Gary PVC Hose (Part #14)
to the brass valve body.
• Disconnect the Gary PVC Hose (Part #14) from the
valve body and remove the Filter Gasket (Part #10).
• Using needle nose pliers, grip the edge of the check
valve and pull straight out..
2
3
Check Valve
1
• Place the new check valve into the valve body.
Observe the direction of the valve is correct.
2
4
Check Valve
2
2
10
2
• Ensure the check valve is flush with the top of the valve
body inlet.
5
Level
• Place the filter gasket (Part #10) back in place and secure
the Gary PVC Hose (Part #14) to the valve body to
complete the install.
2
6
10
How to Replace the Check Valve
14
14
- 18 -
- 19 -
Ten (10) years guaranteed from manufacture defects.
Lifetime limited parts warranty on the diverter valve.
Recycling: Most of the materials used to manufacture this
shower fixture are recyclable. Please dispose of those
materials properly in accordance to your local state laws.
Improper disposing of this shower fixture can be harmful to
the environment.
- 20 -
/
