DAICH Hi-Build Ultra HBU-189 is a high-performance, one-component 35% solids acrylic/urethane hybrid coating used over many interior and exterior surfaces. Here's what you need to know:
- Durable and Protective: Hi-Build Ultra produces a tough, non-yellowing barrier that resists abrasion, impact, stains, chemicals, UV rays, and mold/mildew.
- Versatile Applications: It's ideal as a top coat for concrete and masonry, including DAICH stone floor finishes, and can be used on residential, commercial, and light industrial floor surfaces.
- Easy to Apply: Apply with a 3/8" pile roller onto clean and dry surfaces. Ensure a 24-hour drying time before applying a second coat (if needed).
DAICH Hi-Build Ultra HBU-189 is a high-performance, one-component 35% solids acrylic/urethane hybrid coating used over many interior and exterior surfaces. Here's what you need to know:
- Durable and Protective: Hi-Build Ultra produces a tough, non-yellowing barrier that resists abrasion, impact, stains, chemicals, UV rays, and mold/mildew.
- Versatile Applications: It's ideal as a top coat for concrete and masonry, including DAICH stone floor finishes, and can be used on residential, commercial, and light industrial floor surfaces.
- Easy to Apply: Apply with a 3/8" pile roller onto clean and dry surfaces. Ensure a 24-hour drying time before applying a second coat (if needed).
Hi-Build Ultra™ Clear Coat with Urethane is a high-performance, one-component 35% solids acrylic/urethane
hybrid coating used over many interior and exterior surfaces.
An ideal top coat for concrete and masonry – as well as all DAICH Coatings stone floor finishes – Hi-Build
Ultra produces a tough, non-yellowing barrier that resists abrasion, impact, stains, chemicals and more.
Hi-Build Ultra is a safe, non-toxic, low odor water-based technology
excellent for residential, commercial and light industrial floor surfaces.
PREPARATION:
Surface must be clean and dry, free from dust, dirt, oils, loose flaking, poorly
bonded or glossy paint, glue, surface sealers, efflorescence, etc.
Concrete Surface Preparation:
Pressure wash the concrete or vigorously scrub the surface with a strong TSP
and water solution. Rinse the surface thoroughly and remove wash water with adequate drainage or water-
compatible vacuum. Very smooth, new or efflorescent surfaces may need to be acid etched prior to general
cleaning (ask a qualified source for full instructions). Remove resulting etching residue thoroughly before
coating application. New concrete – allow 30 day cure before coating. New masonry – Cure 48 hours. Allow
the surface to dry completely.
DAICH Decorative Finishes – Surface Preparation:
Surface must be fully cured (at least 24 hours), clean and dry. Remove dirt or loose debris before sealing.
APPLICATION:
Apply uniformly onto the surface using a 3/8” pile roller. Surface should be dry for 24 hours before
applying sealer. Temperature should be at least 50º F during application and for the next 12 hours. Apply
in dry conditions in the morning or late afternoon. Do not apply if rain is expected within 24 hours or take
precautionary measures to shield area from rain. Wash tools with soap and water when finished.
If applying to a Daich Spreadable Stone finish, ensure that the surface beneath is fully cured prior to
application of Hi-Build Ultra. Re-apply until desired film-build is achieved - and ONLY when previous coats
have dried through (at least 8 hours - longer in damp, humid or cool conditions, and/or where there is little air
circulation). On very smooth surfaces, scuff previous coatings lightly before application. Do not step on surface
while it is tacky. Rope off the sealed area to allow curing and discourage normal foot traffic for 24 hours.
COVERAGE: Up to 400 sq.ft. per gallon. Coverage varies with surface roughness and application thickness.
Two coats recommended.
CONTAINER SIZES: Hi-Build Ultra Clear Coat Sealer is available in 1-gallon and 5-gallon containers.
STORAGE: May be stored in its original unopened container for two years.
PRECAUTIONS:
Avoid contact with eyes and skin, flood eyes repeatedly with potable water for 15 minutes. Wash hands
thoroughly after handling. Do not take internally. KEEP OUT OF REACH OF CHILDREN. Keep container closed.
Water-based product. Dispose of unused material as prescribed by local laws.
Hi-Build Ultra Performance Features
• water / weather resistant
• UV resistant
• excellent chemical resistance
• very low odor
• water-based
• glossy finish
• salt resistant
• impact resistant
• abrasion resistant
• mold and mildew resistant
• non-yellowing
• low VOC
PRODUCT DATA SHEET
Multi-Purpose
Sealer with Urethane
TM
-
1
DAICH Hi-Build Ultra HBU-189 User manual
- Type
- User manual
- This manual is also suitable for
DAICH Hi-Build Ultra HBU-189 is a high-performance, one-component 35% solids acrylic/urethane hybrid coating used over many interior and exterior surfaces. Here's what you need to know:
- Durable and Protective: Hi-Build Ultra produces a tough, non-yellowing barrier that resists abrasion, impact, stains, chemicals, UV rays, and mold/mildew.
- Versatile Applications: It's ideal as a top coat for concrete and masonry, including DAICH stone floor finishes, and can be used on residential, commercial, and light industrial floor surfaces.
- Easy to Apply: Apply with a 3/8" pile roller onto clean and dry surfaces. Ensure a 24-hour drying time before applying a second coat (if needed).
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
SpreadRock SPR-FG-189 User manual
-
DAICH RollerRock RRPL-PBS-378 User manual
-
DAICH DCPR-189-CH User manual
-
DAICH DaiHard DGDU-189 User manual
-
DAICH SpreadStone SDCR-U-LR User manual
-
Tracsafe TSASU-37 User manual
-
M-Rock BROOKSHIRECORNERS User manual
-
DAICH DaiHard DCDH-100TN User guide
-
DAICH DCST-AS-150 User manual
-
Ghostshield 4500 User manual
