Kichler Lighting 43694BK User manual

Brand
Kichler Lighting
Model
43694BK
Type
User manual

This manual is also suitable for

IS-43694-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
4) Pass xture wire from last stem through rst loop[D].
Thread rst loop onto end of last stem.
5) Pass xture wire through second loop[E] and through
hole in canopy.
6) (If second loop is already aached to canopy, proceed
to next step). Pass threaded pipe at end of second loop
through hole in canopy. Thread lockwasher[N] onto
threaded pipe protruding from inside canopy. Pass
xture wire through hole in hexnut[M] and thread
hexnut onto end of threaded pipe.
7) Aach chain link[F] to small loop at end of stem and to
loop on canopy. Close the open chain link by placing a piece
of cloth over the open link and using a pair of pliers gently
squeeze the link closed.
8) Find the appropriate threaded holes on mounng
strap[G]. Assemble mounng screws[H] into threaded
holes.
9) Aach mounng strap to outlet box[I] using the strap
mounng screws[O]. The mounng strap can be
adjusted to suit posion of xture.
10) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is
provided,aach ground wire from outlet box under
cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
11) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth
(see illus.)
Neutral Wire
12) Push xture to ceiling, carefully passing mounng screws
through holes in canopy[J]. NOTE: Be certain wires do
not get pinched between canopy and ceiling.
13) Use knobs[K] and lockwashers[L] to secure canopy.
Tighten to secure.
14) Install the recommended bulbs. (Not supplied).
15) Place the glass[P] over the installed bulbs and secure
into place with the glass retainer screws[Q], three (3) per
glass.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Coupler
[B] Stem
[C] Short
Threaded
Tubes
[D] First Loop
[E] Second Loop
[F] Chain Link
[G] Mounting
Strap
[H] Mounting
Screws
[I] Outlet Box
[J] Canopy
[K] Knobs
[L] Lockwashers
[M] Hexnut
[N] Lockwasher
[O] Strap
Mounting
Screws
[P] Glass
[Q] Glass
Retainer
Screws
[R] Center Tube
Assembly
[S] Main Body
1) Assemble the center tube assembly[R] to the main
body[S] by threading the center tube into the elongated
nut in the center and secure into place using the
coupler[A].
2) NOTE: At least one (1) 6 inch tube must be used during
mounng. Pass xture wire from the coupling on top of
xture through a stem[B] and threaded tubes[C] and
screw stem into coupler[A] on top of the main body.
NOTE: Thread locking compound must be applied to
all stem threads as noted with symbol (4) to prevent
accidental rotaon of xture during cleaning, relamping,
etc.
3) Pass xture wire through desired amount of stems and
screw stems together using supplied short threaded
tubes.
Installaon Instrucons (connued)
I
G
O
E
J
D
B
C
M
H
F
►
►
N
K
L
►
A
P
Q
R
S
Page is loading ...
IS-43694-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
4) Pass xture wire from last stem through rst loop[D].
Thread rst loop onto end of last stem.
5) Pass xture wire through second loop[E] and through
hole in canopy.
6) (If second loop is already aached to canopy, proceed
to next step). Pass threaded pipe at end of second loop
through hole in canopy. Thread lockwasher[N] onto
threaded pipe protruding from inside canopy. Pass
xture wire through hole in hexnut[M] and thread
hexnut onto end of threaded pipe.
7) Aach chain link[F] to small loop at end of stem and to
loop on canopy. Close the open chain link by placing a piece
of cloth over the open link and using a pair of pliers gently
squeeze the link closed.
8) Find the appropriate threaded holes on mounng
strap[G]. Assemble mounng screws[H] into threaded
holes.
9) Aach mounng strap to outlet box[I] using the strap
mounng screws[O]. The mounng strap can be
adjusted to suit posion of xture.
10) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is
provided,aach ground wire from outlet box under
cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
11) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth
(see illus.)
Neutral Wire
12) Push xture to ceiling, carefully passing mounng screws
through holes in canopy[J]. NOTE: Be certain wires do
not get pinched between canopy and ceiling.
13) Use knobs[K] and lockwashers[L] to secure canopy.
Tighten to secure.
14) Install the recommended bulbs. (Not supplied).
15) Place the glass[P] over the installed bulbs and secure
into place with the glass retainer screws[Q], three (3) per
glass.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Coupler
[B] Stem
[C] Short
Threaded
Tubes
[D] First Loop
[E] Second Loop
[F] Chain Link
[G] Mounting
Strap
[H] Mounting
Screws
[I] Outlet Box
[J] Canopy
[K] Knobs
[L] Lockwashers
[M] Hexnut
[N] Lockwasher
[O] Strap
Mounting
Screws
[P] Glass
[Q] Glass
Retainer
Screws
[R] Center Tube
Assembly
[S] Main Body
1) Assemble the center tube assembly[R] to the main
body[S] by threading the center tube into the elongated
nut in the center and secure into place using the
coupler[A].
2) NOTE: At least one (1) 6 inch tube must be used during
mounng. Pass xture wire from the coupling on top of
xture through a stem[B] and threaded tubes[C] and
screw stem into coupler[A] on top of the main body.
NOTE: Thread locking compound must be applied to
all stem threads as noted with symbol (4) to prevent
accidental rotaon of xture during cleaning, relamping,
etc.
3) Pass xture wire through desired amount of stems and
screw stems together using supplied short threaded
tubes.
Installaon Instrucons (connued)
I
G
O
E
J
D
B
C
M
H
F
►
►
N
K
L
►
A
P
Q
R
S
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kichler Lighting 43694BK User manual

Brand
Kichler Lighting
Model
43694BK
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents