3M Stamark™ High Performance Tape Series 380AW Operating instructions

3M
Brand
3M
Model
Stamark™ High Performance Tape Series 380AW
Type
Operating instructions

This manual is also suitable for

$B1>C@?BD1D9?>#165DI9F9C9?>
ǩū#D1=1B;ū$1@5C 1F5=5>D
#EB6135 B5@1B1D9?>1>4
@@<931D9?>$538>9AE5C
>6?B=1D9?>?<45Bǫǭ
1>E1BIǨǦǧǮ
"5@<135Cǫǭ41D54E<IǨǦǧǫ
Introduction ..........................................................................................................................................................................................2
Product Application Requirements ................................................................................................................................................3
Adhesive Series of Stamark Tapes ..................................................................................................................................................3
Hot Inlay Application of Long Lines ................................................................................................................................................4
Hot Inlay Application of Transverse Markings ............................................................................................................................7
Overlay Application of Long Lines ............................................................................................................................................... 9
Overlay Application of Transverse Markings ............................................................................................................................. 13
Storage .............................................................................................................................................................................................. 16
Removal .............................................................................................................................................................................................. 16
Health and Safety ............................................................................................................................................................................ 16
Caution ...............................................................................................................................................................................................16
Appendix A. Pavement Surface Types ........................................................................................................................................ 17
Appendix B. Surface Preparation Adhesives ...............................................................................................................................18
Appendix C. Road Type Surface Preparation Adhesive Application Recommendations .................................................19
Literature Reference .........................................................................................................................................................................19
Ǩ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
>DB?4E3D9?>
This information folder contains pavement surface preparation requirements and application
procedures for 3M
™
Stamark
™
Pavement Marking Tapes. It is important that users be
completely knowledgeable of all application requirements and procedures prior to product
application. Instructions contained in this folder must be followed for material replacement
provisions to be considered valid. Material replacement provisions are described in the
appropriate product bulletins.
It is the responsibility of the installer to contact the 3M sales representative or 3M
technical service representative whenever there is a question regarding application procedures
or conditions.
3M
™
#D1=1B;
™
$1@55>5B1< B?4E3D#E==1BI
#D1=1B;D1@5C1B54EB12<5B5ɦ53D9F5@1F5=5>D=1B;9>7D1@5CEC54D?=1B;1C@81<D1>4
concrete surfaces. Stamark tape is available in white or yellow, standard widths and roll
sizes, and Adhesive A series (unlinered), L series (linered) or N series (no liner and no adhesive).
Custom sizes are available upon request. It is also available in legend and symbol patterns.
Below is a summary of each series of Stamark tape along with recommendations for
appropriate uses.*
 3M
™
#D1=1B;
™
<<'51D85B$1@5#5B95CǩǮǦ'1>4ǩǮǦ'ǫ
#D1=1B;1<<G51D85BD1@59C14EB12<5@1F5=5>D=1B;9>7D1@5D81D9C8978<IB5DB?B5ɦ53D9F5
under both wet and dry conditions. Series 380AW tape utilizes specially designed optics to
provide wet and dry performance. Series 380AW tape can be used as a hot inlay marking
on new asphalt or as an overlay marking on most asphalt and concrete pavement surfaces in
good condition. Series 380AW-5 consists of standard white pavement marking tape with
a 1.5 inch wide black edge to provide contrast on light colored asphalt or portland cement
concrete surfaces.
 3M
™
#D1=1B;
™
978 5B6?B=1>35$1@5#5B95CǩǯǦǩǯǦǫ
ǩǮǦ#1>4ǩǮǦǫ#
Stamark high performance tape is a durable, conformable pavement marking providing a
8978457B55?6B5DB?B5ɦ53D9F9DI1>44EB129<9DI$89C@1F5=5>D=1B;9>7D1@59C=1>E613DEB54
G9D81@1DD5B>54CEB6135D81D@B5C5>DC1>51BF5BD931<@B?ɥ<5D?D85=?D?B9CDD?=1H9=9J5
B5DB?B5ɦ53D1>351>41@<91>D@?<I=5B3?>6?B=1>35<1I5B6?B<?>7D5B=4EB129<9DI"53?==5>454
for a wide variety of uses including long line, gore areas, and intersections (low to medium
C851B<978DDBE3;DB1ɣ3?><I6?B9><1I7B??F541>4?F5B<1I1@@<931D9?>C#5B95CǩǯǦǫ1>4
380I-5 ES consists of standard white pavement marking tape with a 1.5 inch wide black edge to
provide contrast on light colored asphalt or ortland cement concrete surfaces.
 3M
™
#D1=1B;
™
 1F5=5>D1B;9>7$1@5#5B95CǨǭǦ#
Stamark pavement marking tape is manufactured with a polymer conformance layer for
4EB129<9DI1>41@1DD5B>54CEB61356?BB5ɦ53D9F9DI"53?==5>4546?B1G945F1B95DI?6EC5C
including intersection and longitudinal markings.
*See Information Folder 3.2 for information on 3M
™
Stamark
™
Removable Pavement
Marking Tapes.
3
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
F5B<1I B?4E3D@@<931D9?>"5AE9B5=5>DC
The following general requirements apply to all Stamark tape applications:
ɟ $5=@5B1DEB5C
Air and Surface Temperature: Minimum 40°F (4°C) and rising
Overnight Air Temperature: Minimum 40°F (4°C) the night before
tape application is recommended. If the temperature falls below
40º F, inspect the pavement surface for visible signs of moisture
(dew, frost, etc.).
• Overlay applications must be completed within the seasonal start and
end dates for a particular region as indicated in the 3M Climate Guide
for 3M
™
Stamark
™
Pavement Marking Tapes.
• If outside your seasonal start or end date, you must use 3M
™
Low
VOC Surface Preparation Adhesive SPA60 or 3M
™
Stamark
™
Surface
Preparation Adhesive P-50 when air and surface temperature is 40°F
and rising.
?D5"579?>C>?D3?F5B549>D85<9=1D5E945=ECD6?<<?G=9>9=E=D5=@5B1DEB5
B5AE9B5=5>DC
ɟ $85@1F5=5>DCEB6135=ECD253<51>1>44BI?@B539@9D1D9?>G9D89>
ǨǪ8?EBC@B9?BD?1@@<931D9?>D85BF9C92<5C97>C?6=?9CDEB545G
?B6B?CD31>>?D25@B5C5>D 6851FI?B@B?<?>754B19>9C@B5493D54
D?2579>G9D89>ǨǪ8?EBC?69>CD1<<1D9?>EC5?6#EB6135 B5@1B1D9?>
485C9F5# ǬǦ?B ǫǦ9CB53?==5>454
• Butt splices must be used; do not overlap tape ends.
• $B1ɣ3=ECD25;5@D?ɢ?6@1F5=5>DCEB6135C3?1D54G9D81CEB6135
preparation adhesive prior to tape application. Minimize debris (dirt and
excess dust) as much as possible.
485C9F5#5B95C?6#D1=1B;$1@5C
485C9F5ŏŐ#5B95CTapes with pressure sensitive adhesive.
“A” Series tapes are shipped on a roll with a release agent top coating
on the pavement marking surface. The adhesive on the back of the
tape is ready for placement on the road surface once the tape is peeled
from the roll.
485C9F5ŏŐ#5B95C Tapes with liner and pressure sensitive adhesive.
“L” Series tapes are available in both long line pavement markings as
well as all symbols and legends. “L” Series tapes are shipped with a liner
on the adhesive backing of the tape to allow for ease of handling prior to
placement on the road surface. The liner is removed just before placement
on the pavement.
485C9F5ŏŐ#5B95C Tapes
with no liner and no pressure
sensitive adhesive.
“N” Series tapes are manufactured
with no adhesive backing on the tape.
“N” Series tapes must be applied with
surface preparation adhesive SPA60
by using the SPA60 cylinder, hose
and spray gun. (See Appendix B for
more information.)
$B1>C@?BD1D9?>#165DI9F9C9?>
D538>931<C5BF935B5@B5C5>D1D9F5
31>253?>D13D541D
ǧǮǦǦǫǫǩǧǩǮǦ9>D85%#?B1D
ǧǮǦǦǨǬǫǧǮǪǦ9>1>141G85>
@B?=@D54C5<53DD538>931<C5BF935
1>4D85>C5<53D@1F5=5>D=1B;9>7
@B?4E3DC
B?4E3D@@<931D9?>
Stamark tapes can be applied by
a hot inlay application (embedding
pavement marking tape into fresh
asphalt) or by an overlay application
(applying tape on existing surface).
The tapes can also be recessed
into a grooved surface. Refer to IF
5.18 for more information about a
grooved application.
Ǫ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
?D><1I@@<931D9?>?6?>79>5C
Including edge, lane and channelizing lines
Stamark tapes with pressure sensitive adhesive can be applied on fresh
1C@81<D256?B5D85ɥ>9C89>7B?<<5B@1CC5C?F5BD85CEB6135?D9><1I9>79CD85
process of embedding pavement marking tape into the road surface. This is
4?>52IB?<<9>7?F5BD851@@<954D1@5G9D81CD55<4BE=ɥ>9C89>7B?<<5BG89<5
the asphalt is still warm. (See Figure 1.)
97EB5ǧ
 B?354EB5
ǧ 1F51<1>5
Lanes should be paved so that the tape will not be placed on the asphalt
C51=C25DG55><1>5C5>5B1<<ID85G94D8?6D85ɥBCD<1>5C8?E<425
approximately 12 inches (30.5 cm) short of center (for example, a 12-foot
[3.7 m] wide lane should be paved at 11 feet [3.3 m] wide). The second pass
will then be paved 13 feet (4.0 m) wide, for a total road width of 24 feet
(7.3 m). Center line markings will then be applied on a fresh, warm mat
during paving of the adjacent lane, at least four inches (10 cm) from the
asphalt seam.
Ǩ ?=@13DD856B5C81C@81<DG9D813?=@13D9?>B?<<5B
ǩ B5=1B;D85B?14
Use 200-250 feet (60-70 m) of sash chain or thin wire cable as a guide
for long line applications or snap chalk lines on the asphalt. For skip line
application, mark the skip sequence on a sash chain or with chalk or paint to
be followed by the pointer on a tape applicator. (See Figure 2.)
Example: A sash chain marked to the proper skip sequence with one-inch
(2.5 cm) spiral key rings.
Ǫ $5CDD851C@81<DCEB6135
The pavement surface must be soft enough to allow the marking to be inlaid
2ID85CD55<4BE=69>9C89>7B?<<5B1D5>D?>69>9C89>7B?<<5B9CB53?==5>454
Generally, the desired surface temperature will be between 130°F (54°C)
and 160°F (71°C). Using a surface thermometer, test the temperature of the
asphalt surface. There is no minimum air temperature requirement for a hot
inlay tape application; however, be advised that cooler air temperatures will
result in faster cooling of the asphalt reducing the application window.
?D56I?E1B5EC9>71CD9ɢ5B=9HBE225B
21C54=9HBE225B9J541C@81<D#E@5B@1F5
@5>B145B93D9?>?EBC5?B
##D?>51DB9HC@81<DI?E=1I>554
D?9>3B51C5D85D5=@5B1DEB51DG8938D85
D1@59CB535CC54G9D81ɥ>9C89>7B?<<5BD?
B5138D8545C9B541=?E>D?65=254=5>D
9>D?D85CEB6135?D9><1ID85D1@5G9D8D85
ɥ>9C89>7B?<<5BG89<5D85CEB6135D5=@5B1DEB5
9CG1B=5>?E78D?75D1@@B?H9=1D5<IǫǦD?
ǬǦ@5B35>D?6D85D1@5ōCD893;>5CC25<?GD85
1C@81<DCEB6135?>?D5H3554ǧǮǦǹǮǩǹ
?D5>?B45BD?13895F5@B?@5B5=254=5>D
3??B49>1D9?>9C3B9D931<25DG55>D85@1F5B
1>4D85D1@51@@<931D9?>3?>DB13D?BD9C1<C?
3B9D931<D?81F53<51B3?==E>931D9?>1>4
45ɥ>9D9?>?6B?<5C4EB9>7D85@B53?>CDBE3D9?>
=55D9>7C?5F5BI?>59CG?B;9>79>E>9C?>
ǫ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
ǫ E2B931D5D85D1@51@@<931D?B961@@<9312<5
Prepare the tape applicator for use. Spray the rear rubber wheels, front
wheel, and pivot points of the tape applicator with 3M
™
5-way Penetrant,
WD-40
™
or equivalent light oil spray. The rear wheels and pointer wheel
should be sprayed regularly to avoid asphalt build-up.
?D5'855<C=1I1<C?25GB1@@54G9D84E3DD1@5"5@<135B57E<1B<ID?1F?942E9<4E@
#5597EB5Ǩ
$1@5@@<931D?B
97EB5Ǩ
Ǭ B?354EB56?BD8B5149>7D1@596EC9>7D85D1@51@@<931D?B
Load the tape and thread over the two-inch (5.08 cm) diameter roll,
adhesive side up. (Figure 3) Feed the tape in between the side frame
connecting rod and the two-inch aluminum roller, then through the CLAMP
to the CUTTER PLATE. Adjust the GUIDE BARS at the sides of the tape rolls
to hold them securely in position.
$ thread tape over the half inch diameter side frame connecting rod.
This will create excessive unwind tension and stretching of the tape.
1ED9?>
Do not activate the cutting knife with the foot pedal while threading tape!
For any other equipment questions, contact technical service at
1-800-553-1380.
?D5$89C<9CD9C>?D9>3<EC9F51>4?D85BD1@51@@<931D9?>5AE9@=5>D81C255>EC54
CE335CC6E<<ID?1@@<Iǩ#D1=1B;D1@5C <51C53?>D13Dǩ$538>931<#5BF93596D85B51B5
AE5CD9?>C12?ED5AE9@=5>D>?DC@539ɥ31<<I<9CD5412?F5
97EB5ǩ
ǭ @@<ID85D1@5
Apply the tape using the tape
applicator. Make sure you do not apply
the tape any closer than four inches
(10.16 cm) from the asphalt seam. (See
Figure 4.)
97EB5Ǫ
If pavement markings are applied using
a tape applicator, the weight of the
tape applicator roller will be adequate
to cause the adhesive to tack with the
fresh asphalt prior to rolling with the
steel-drum roller. If pavement markings
are placed by hand (i.e., shorter,
individual skip marks), walk on the tape
ɥBCDD?D13;D851485C9F5?>D851C@81<D
and then roll the tape using one pass
with a Roller Tamper Cart RTC-2 with
50-100 lb. (45 kg) prior to rolling with a
CD55<4BE=ɥ>9C89>7B?<<5B
Ǭ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
Ǯ B5CCD85D1@59>D?D85@1F5=5>D
%C9>71D1>45=CD55<4BE=ɥ>9C89>7B?<<5B>?F92B1D9?>, slowly roll over
the tape to press (inlay) it into the warm pavement surface. The tape should
1<G1IC25B?<<54ɥBCD@1CC9>D85C1=549B53D9?>9DG1C1@@<954$85C@554
?6D85ɥ>9C89>7B?<<5BC8?E<425;5@DD?1=9>9=E=25DG55>DG?1>4D8B55
=@8+ǩ1>4ǫ;@8-G85>B?<<9>7?F5BD85D1@54EB9>7D85ɥBCD@1CC%C51
=9>9=E=1=?E>D?6G1D5BD?3<51>1>4<E2B931D5D85CD55<4BE=C4EB9>7
D858?D9><1I?@5B1D9?>
(See Figure 5.)
97EB5ǫ
?D5?B25CD9><1IB5CE<DCD85G5978D?6D85CD55<4BE=B?<<5BC8?E<4
257B51D5BD81>ǧǧǦ  ?E>4C@5B9>51<>38?64BE=G94D8
1<3E<1D9?>
What you’ll need:
• The width of the roller in inches as shown
• The total weight of the machine in pounds
• The number of rollers on the machine (usually two)
Weight of machine
Number of Rollers x Width of roller
H1=@<5
=1389>5D81DG5978CɥF5D?>CǧǦǦǦǦ<2C
that has two rollers that are each 60 inches wide:
10,000lb
2 × 60in
$I@931<<I1D8B55D?ɥF5D?>ǪǨ9>38
wide roller will apply over 140 PLI.
Under normal conditions, a minimum
?6D8B55@1CC5C?6D85ɥ>9C89>7B?<<5B
is required to hot inlay the tape. >
9><1I9C3?>C945B54CE335CC6E<G85>
1@@B?H9=1D5<IǫǦD?ǬǦ@5B35>D?6D85
D1@5ōCD893;>5CC9C25<?GD851C@81<D
CEB6135 (See Figure 1 on page 4.) To
test for embedment use a 40 mil depth
gauge or a bridge micrometer. For more
information on embedment, contact
technical service at 1-800-553-1380.
?D56D85D1@5GB9>;<5C?B49CD?BDCC5F5B5<I
9>6B?>D?6D85B?<<5BD85=1DD5=@5B1DEB5=1I
25D??8?D?BD85B?<<5BC@554=1I25D??61CD
<<?GD85CEB6135D?3??<C<978D<I1>4B5DBI?
>?DB5=?F5D859><194D1@5C9>35B5=?F1<?6D85
D1@5G9<<B5=?F5D851C@81<D
ǯ "5@51D#D5@CǧǮE>D9<D85B?14
9C6E<<I=1B;54
ǧǦ@5>D85B?14D?DB1ɣ3
As soon as the hot inlay operations are
complete and the asphalt has cooled
to temperatures that support vehicles
without surface damage, the road may
25?@5>54D?DB1ɣ3
?D5$1@5@1DD5B>9C9=@?BD1>D6?BF9C929<9DI
@5B6?B=1>35>9=@B?@5B8?D9><1I=1I31EC5
D1@5@1DD5B>ɦ1DD5>9>7=51CEB549>3B51C5?6
1@@<954D1@5G94D87B51D5BD81>ǧǮ9>38ǩ==
=1I251>9>4931D9?>D81D@1DD5B>ɦ1DD5>9>781C
?33EBB54
PLI=
PLI= 83.3
lb
in
ǭ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
?D><1I@@<931D9?>?6$B1>CF5BC51B;9>7C
Including crosswalks, stopbars, gore markings, symbols and legends
Stamark tapes with pressure sensitive adhesive (Adhesive A Series [no
liner] and Adhesive L Series [with liner; also includes precut symbols and
legends known as SMS-L Series]) can be applied on fresh asphalt before the
ɥ>9C89>7B?<<5B81C@1CC54?F5BD85CEB6135?D9><1I9>79CD85@B?35CC?6
embedding the pavement marking tape into the road surface. This is done
2IB?<<9>7?F5BD851@@<954D1@5G9D81ɥ>9C89>7B?<<5BG89<5D851C@81<D9CCD9<<
warm. (See Figure 6.)
B?CC#53D9?>?6D85"?14
97EB5Ǭ
 B?354EB5
ǧ 1F51<1>5(See Step 1 on Page 4.)
Ǩ ?=@13DD856B5C81C@81<DG9D813?=@13D9?>B?<<5B
ǩ B5=1B;D85B?14
Using chalk, outline the area where the marking will be applied.
Ǫ $5CDD851C@81<DCEB6135
The pavement surface must be soft enough to allow the marking to be hot
9><1942ID85CD55<4BE=ɥ>9C89>7B?<<5B
Generally, the desired surface temperature will be between 130°F (54°C)
and 160°F (71°C). Using a surface thermometer, test the temperature of the
asphalt surface. There is no minimum air temperature requirement for a hot
inlay tape application; however, be advised that cooler air temperatures will
result in faster cooling of the asphalt reducing the application window.
?D56I?E1B5EC9>71CD9ɢ5B=9HBE225B21C54=9HBE225B9J541C@81<D#E@5B@1F5
@5>B145B93D9?>?EBC5?B##D?>51DB9HC@81<DI?E=1I>554D?
9>3B51C5D85D5=@5B1DEB51DG8938D85D1@59CB535CC54G9D81ɥ>9C89>7B?<<5BD?B5138D85
45C9B541=?E>D?65=254=5>D9>D?D85CEB6135?D9><1ID85D1@5G9D8D85ɥ>9C89>7B?<<5B
G89<5D85CEB6135D5=@5B1DEB59CG1B=5>?E78D?75D1@@B?H9=1D5<IǫǦD?ǬǦ@5B35>D?6D85
D1@5ōCD893;>5CC25<?GD851C@81<DCEB6135?>?D5H3554ǧǮǦǹǮǩǹ
ǫ @@<ID85D1@5
Apply the tape by hand. Cut the tape
approximately 12 inches (30.5 cm) short
of the asphalt seam or edge. Once the
adjacent lane is paved, the tape should
meet the end of the tape placed in the
ɥBCD@1F54<1>5?>?D?F5B<1@D85
material. Use butt splices.
(See Figure 7.)
After the next length of tape is placed
and buttspliced with the tape placed
4EB9>7@1F9>7?6D85ɥBCD<1>5D85
tape will not be inlaid through the 12-
inch wide area between the seam and
butt splice. To prevent tape loss in
snowplow regions from this small area
of tape overlay, use a utility knife to
score a relief cut across the width of the
tape just outside the seam and into the
hot inlay area. (See Figure 7.)
97EB5ǭ
For material with liner (Adhesive L
Series), including legends and symbols:
Position the marking and peel back
the liner. Refer to IF 5.8 for liner
removal techniques. Press the exposed
tape down. Slowly remove the rest of
the liner as the tape is carefully guided
into place.
Ǯ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
Ǭ $1=@D85D1@5
Use a Roller Tamper Cart RTC-2 loaded with ǧǦǦ@?E>4CǪǫ;7(two
standard 50-pound weights) to get initial tack of the tape to the asphalt.
This tamping of the tape should always be done in the same direction as
the marking was applied (lengthwise, not crosswise). #D1BD9>D8535>D5B?6
D85=1B;9>7, then work toward the edges of the tape to remove trapped air.
Make sure all the edges of the tape are thoroughly tamped. Do not twist or
DEB>D85D1=@5B31BD?>D85D1@5>5@1CC?F5B51381B519CCEɣ395>D#55
Figure 8.) If the tape folds or distorts in front of tamper center, remove one 50
lb weight and continue tamping.
97EB5Ǯ
ǭ B5CCD85D1@59>D?D85@1F5=5>D
%C9>71D1>45=CD55<4BE=ɥ>9C89>7B?<<5BG9D8>?F92B1D9?>, slowly roll
over the tape to press (inlay) it into the warm pavement surface. Roll back
and forth in a straight line over the same section of tape before moving
?F5BD?D85>5HDC53D9?>$85C@554?6D85ɥ>9C89>7B?<<5BC8?E<425;5@DD?
a minimum (between two and three mph [3 and 5 kph]) when rolling over
the tape. %C51=9>9=E=1=?E>D?6G1D5BD?3<51>1>4<E2B931D5D85CD55<
4BE=C4EB9>7D859><1I?@5B1D9?>(See Figure 9.)
?D5?B25CD8?D9><1IB5CE<DCD85G5978D?6D85CD55<4BE=ɥ>9C89>7B?<<5BC8?E<425
7B51D5BD81>ǧǧǦ ?E>4C@5B9>51<>38 ?64BE=G94D8
1<3E<1D9?>
What you’ll need:
• The width of the roller in inches as shown
• The total weight of the machine in pounds
• The number of rollers on the machine (usually two)
Weight of machine
Number of Rollers x Width of roller
H1=@<5
=1389>5D81DG5978CɥF5D?>CǧǦǦǦǦ<2CD81D
has two rollers that are each 60 inches wide:
10,000lb
2 × 60in
$I@931<<I1D8B55D?ɥF5D?>ǪǨ9>38
wide roller will apply over 140 PLI.
%C51C=1<<5BB?<<5BD8B55D?ɥF5D?>6?B
intersection markings if one is available.
Smaller rollers are generally more
maneuverable and allow the markings
D?258?D9><194=?B55ɣ395>D<ID=1I
be possible to hot inlay intersection
markings in a longitudinal direction to
the markings if the roller is small and
the operator is experienced.
Under normal conditions, a minimum
of three passes back and forth of the
ɥ>9C89>7B?<<5B1B5B5AE9B54D?8?D
inlay the tape. >9><1I9C3?>C945B54
CE335CC6E<G85>1@@B?H9=1D5<IǫǦD?
ǬǦ@5B35>D?6D85D1@5ōCD893;>5CC9C
25<?GD851C@81<DCEB6135(See Figure
1 on page 4). $?D5CD6?B5=254=5>D
EC51ǪǦ=9<45@D871E75?B12B9475
=93B?=5D5B?B=?B59>6?B=1D9?>?>
5=254=5>D3?>D13DD538>931<C5BF935
1DǧǮǦǦǫǫǩǧǩǮǦ
?D56D85D1@5GB9>;<5C?B49CD?BDCC5F5B5<I
9>6B?>D?6D85B?<<5BD85=1DD5=@5B1DEB5=1I
25D??8?D?BD85B?<<5BC@554=1I25D??61CD
<<?GD85CEB6135D?3??<C<978D<I1>4B5DBI?
>?DB5=?F5D859><194D1@5C9>35B5=?F1<?6D85
D1@5G9<<B5=?F5D851C@81<D
PLI=
PLI= 83.3
lb
in
97EB5ǯ
ǯ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
Ǯ "5@51D#D5@CǧǭE>D9<D85B?149C6E<<I=1B;54
ǯ @5>D85B?14D?DB1ɣ3
As soon as the hot inlay operations are complete and the asphalt has cooled to temperatures
D81DCE@@?BDF5893<5CG9D8?EDCEB613541=175D85B?14=1I25?@5>54D?DB1ɣ3
?D5$1@5@1DD5B>9C9=@?BD1>D6?BF9C929<9DI@5B6?B=1>35>9=@B?@5B9><1I=1I31EC5D1@5@1DD5B>ɦ1DD5>9>7
=51CEB549>3B51C5?61@@<954D1@5G94D87B51D5BD81>ǧǮ9>38ǩ===1I251>9>4931D9?>D81D@1DD5B>ɦ1DD5>9>7
81C?33EBB54
F5B<1I@@<931D9?>?6?>79>5C
Including edge, lane and channelizing lines
 B?354EB5
This procedure explains how to apply tape to a concrete or asphalt surface in the form of
edge, lane, and channelizing lines. Before you begin, make sure your environment meets all the
product application requirements on page 3.
Surface preparation adhesive SPA60 and P-50 are generally the recommended surface
@B5@1B1D9?>1485C9F56?B<?>7<9>5@1F5=5>D=1B;9>7D1@51@@<931D9?>5H35@D9>165GC@539ɥ3
applications.
Use this chart to determine the proper tape and type of surface preparation adhesive to use.
(See Appendix B for application coverage guidelines)
?>7<9>5
1@@<931D9?>
"53?==5>454
485C9F5#5B95C
?6#D1=1B;$1@5
C@81<D
Ǧǩ41IC?<4
C@81<D
ǪǧǦ41IC?<4
C@81<D
DzǧǦ41IC?<4 ?>3B5D52
Edge Line A None SPA60 or P-50 SPA60 or P-50 SPA60 or P-50
Center or Lane
Line
A None SPA60 or P-50 SPA60 or P-50 SPA60 or P-50
Channelization
Line
A None SPA60 or P-50 SPA60 or P-50 SPA60 or P-50
Edge Line at High
Vehicle Crossover
Location (a)
A None None SPA60 or P-50 (c) SPA60 or P-50 (c)
?D5C
1 H1=@<5C3?E<49>3<E455475<9>5C13B?CC8978F?<E=5B?141335CC@?9>DC?B8978F?<E=53B?CC?F5BDB1ɣ3
D8B?E781=5491>1B51G9D85475<9>5C
2 5G3?>3B5D5CEB6135C?@5>D?DB1ɣ3<5CCD81>ǯǦ41IC=ECD81F5D853EB9>73?=@?E>4B5=?F54@B9?BD?
1@@<931D9?>?6CEB6135@B5@1B1D9?>1485C9F51>4@1F5=5>D=1B;9>7C
3 # ǬǦ1>4 ǫǦ1B5D85?><ICEB6135@B5@1B1D9?>1485C9F5CB53?==5>4546?BEC5G9D8#5B95CǩǮǦ'ǩǯǦǩǮǦ
#?BǨǭǦ#D1@5C?><?>7<9>51@@<931D9?>C
ǧǦ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
ǧ 5D5B=9>5B?14CEB61353?>49D9?>C
a. 6CEB61359C>5G3?>3B5D5?@5>D?DB1ɣ3<5CCD81>ǯǦ41ICB5=?F5
curing compound by sandblasting, shotblasting, light grinding, or
hydroblasting.*
b. If markings exist on the roadway, remove markings from the surface by
sandblasting, grinding shotblasting or hydroblasting.*A minimum of 90
percent of the road surface under the existing markings must be exposed
prior to tape application.
c. Applying Stamark tape over longitudinal joints is not recommended.
Premature tape failure can occur as joints can shift and degrade over
time. Transverse joints or cracks that are wider or deeper than normal
can prevent the tape from conforming to the road surface. As joint
maintenance is required, the markings can be damaged by maintenance
5AE9@=5>D1>4:?9>Dɥ<<5BC61@@<931D9?>?F5B1>I:?9>D9C>535CC1BI3ED
the tape one inch (2.54cm) away from the joint on both sides.
?D5?<<?G9>78I4B?2<1CD9>71ǨǪ8?EB4BI9>7@5B9?49CB5AE9B54256?B5D1@531>251@@<954
Ǩ <51>D85B?14
Clean the surface of the road where the tape will be applied. Clean the
surface using a high pressure, high velocity compressed air blower with
=9>9=E=ǧǮǫ36=19Bɦ?G1>4ǧǨǦ@C91DD8519B>?JJ<5$85B5C8?E<425>?
more than 50 feet of 3/4-inch ID hose from the compressor to the air nozzle
and the air nozzle should be no less than 1/2-inch ID. The compressor should
also be equipped with a moisture and oil trap. It is recommended that the
air nozzle be no more than two feet from the ground. A street sweeper or
@93;E@2B??==1I1<C?255ɢ53D9F5D?B5=?F5<1B75B?B1485B54452B9C
2EDG9<<B5AE9B51ɥ>1<@1CCG9D8D8519B3?=@B5CC?BD?3?=@<5D5<I3<51>D85
surface. The road surface must be dry.
ǩ B5=1B;D85B?14(See Step 3 on Page 4.)
Ǫ 5D5B=9>5 96 CEB6135 @B5@1B1D9?> 1485C9F5 # ǬǦ ?B ǫǦ 9C
B5AE9B54 ?B 1449D9?>1< 9>6?B=1D9?> ?> 1@@<931D9?> B565B D? @B?4E3D
2E<<5D9>6?BD1@5D?251@@<954
a. If no adhesive is required, go to Step 7.
b. If adhesive is required, go to Step 5.
?D56I?E81F51>IAE5CD9?>C3?>D13Dǩ$538>931<#5BF935C1DǧǮǦǦǫǫǩǧǩǮǦ?<<?G
D851ED?=1D93@B?=@DD?B5138D538>931<C5BF935D?45D5B=9>596CEB6135@B5@1B1D9?>
1485C9F59C>55454
ǫ @@<ID851485C9F5# ǬǦ?B ǫǦ?><I
Using a Spray Applicator PS-14, apply a thin, uniform coat of SPA60 or P-50
adhesive to the pavement. The adhesive should extend at least one inch (2.5
cm) beyond the premarked area where the edges of the tape will be applied.
(See Figure 10.) The PS-14 applicator is designed to spray a six inch (15.2 cm)
wide pattern for application of four inch (10.2 cm) wide tape. The typical wet
thickness is 6-7 mil.
Stamark Surface
Preparation
Adhesive
97EB5ǧǦ
Adjust the arm of the PS-14 applicator
up or down so that the spray pattern is
six inches (15.2 cm) wide.
(See Figure 11.)
97EB5ǧǧ
?D56I?E1B5EC9>7D1@5G945BD81>6?EB
9>385CC@B1I=E<D9@<5@1CC5C?F5B<1@@9>7D85
@B5F9?EC@1DD5B>2I?>5D?DG?9>385C<<?G
1449D9?>1<D9=56?B?F5B<1@@541B51C
D?C5D#55@@5>49HD?45D5B=9>5D851=?E>D
?61485C9F5D81D9C>55454D?3?F5B
1C@539ɥ31B51
ǧǧ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
Ǭ <<?GD851485C9F5D?C5D
a. Allow the P-50 to set. P-50 is set when it feels tacky but is no longer in
<9AE946?B=1>481C1=1DD5ɥ>9C8B1D85BD81>17<?CCIG5D1@@51B1>35
P-50 dries quickly (to a set state) under most circumstances. Typical time
for P-50 to set is two to three minutes under optimal conditions of 70°F
(21°C) and medium to low humidity levels. For more information on P-50
application procedures see Information Folder 5.17. See Figure 17 on
page 14.
b. Allow SPA60 to dry. SPA60 is dry when it no longer feels tacky. Dry time
9C1@@B?H9=1D5<IɥF5=9>ED5C?G5BD5=@5B1DEB5C1>489785B8E=949DI
will increase dry times. For more information on SPA60 application
procedures see Information Folder 5.21.
ǭ B?354EB56?BD8B5149>7D1@596EC9>7D85D1@51@@<931D?B
Load the tape and thread over the two-inch (5.08 cm) diameter roll,
adhesive side up. (Figure 12) Feed the tape in between the side frame
connecting rod and the two inch aluminum roller, then through the CLAMP
to the CUTTER PLATE. Adjust the GUIDE BARS at the sides of the tape rolls
to hold them securely in position.
$ thread tape over the half inch diameter side frame connecting rod.
This will create excessive unwind tension and stretching of the tape.
1ED9?> Do not activate the cutting knife with the foot pedal while
threading tape!
97EB5ǧǨ
?D5$89C<9CD9C>?D9>3<EC9F51>4?D85BD1@51@@<931D9?>5AE9@=5>D81C255>EC54
CE335CC6E<<ID?1@@<Iǩ#D1=1B;D1@5C <51C53?>D13Dǩ$538>931<#5BF93596D85B51B5
AE5CD9?>C12?ED5AE9@=5>D>?DC@539ɥ31<<I<9CD5412?F5
Ǯ @@<ID85D1@5
Apply the tape using the tape
applicator. Make sure the tape is not
applied any closer than four inches
(10.16 cm) from longitudinal seam.
97EB5ǧǩ
If pavement markings are placed
by hand (i.e. shorter, individual skip
=1B;CG1<;?>D85D1@5ɥBCDD?D13;D85
adhesive on the pavement surface.
?D56D85B59C13B13;9>D85@1F5=5>D?B96D85
D1@59CD?251@@<954?F5B12B94755H@1>C9?>
:?9>D<1ID85D1@5?F5BD853B13;?B:?9>DD85>
3EDD85D1@5?>59>381G1I6B?=D853B13;?B
:?9>D?>5138C945#5597EB5ǧǪ
97EB5ǧǪ
ǧǨ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
ǯ $1=@D85D1@5&") "$$
Tamp the tape thoroughly with the RTC-2 tamper cart with a minimum ǨǦǦ@?E>4ǯǦ;7 load
making a minimum of six passes, or slowly drive over the tape for a total of six tire hits with a
vehicle. The vehicle must be equipped with a pointing device to aid in keeping the vehicle on
the tape, making six passes forward over the tape. Use a vehicle tire on long line markings only.
When using the RTC-2 tamper cart (See Figure 8, Page 8):
• Do not twist or turn the tamper cart on the tape.
• Make a minimum of six tamping hits all forward passing. Tire strikes from front and rear
wheels when aligned with the aid of a pointer can be completed in 3 passes.
• If tape is wider than the roller or vehicle tire, more passes will be needed to make sure the
entire width of the tape has received the required tamping treatment. $ #$
#$ "$$#$ $$  $ "##
• 1;5CEB51<<5475C1B5ɥB=<I1485B54
ǧǦ@5>D85B?14D?DB1ɣ3
ǧǩ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
F5B<1I@@<931D9?>?6$B1>CF5BC51B;9>7C
Including crosswalks, stopbars, gore markings, symbols and legends
 B?354EB5
This procedure explains how to apply tape to a concrete or asphalt surface in the form of
crosswalks, stopbars, gore markings, symbols and legends. Before you begin, make sure your
environment meets all the product application requirements on page 3.
Use this chart to determine the proper tape and type of surface preparation adhesive to use. (See
Appendix B for application coverage guidelines).
?D5C978C851B5H@?CEB5C=1IB5AE9B5D85EC5?6# ǬǦ?B ǫǦ"565BD?1@@5>49H6?B7E945<9>5C
"53?==5>454#EB6135 B5@1B1D9?>
485C9F5C@81<D
$B1>CF5BC51B;9>7
@@<931D9?>
"53?==5>454
485C9F5
#5B95C?6
#D1=1B;$1@5
C@81<D
Ǧǩ41IC?<4
C@81<D
ǪǧǦ41IC?<4
C@81<D
DzǧǦ41IC?<4
?>3B5D52
?>3B5D51
Crosswalks A, L or N* None None
SPA60 (b) or
P-50 (f)
SPA60 (b) or P-50 (f)
Stop Bars A, L or N* None None
SPA60 (b) or
P-50 (f)
SPA60 (b) or P-50 (f)
Symbols & Legends L or N* None
SPA60 (b) or
P-50 (f)
SPA60 (b) or
P-50 (f)
SPA60 (b) or P-50 (f)
Gore Markings in Minimal
$B1ɣ3B513
A or N* None
SPA60 or
P-50 (e)
SPA60 (b) or
P-50 (f)
SPA60 (b) or P-50 (f)
Gore Markings in Heavy
$B1ɣ3B514
A or N* None
SPA60 or
P-50 (e)
SPA60 (b) or
P-50 (f)
SPA60 (b) or P-50 (f)
*Use only SPA60 for Adhesive Series “N” tapes.
a. 5G3?>3B5D5CEB6135C?@5>D?DB1ɣ3<5CCD81>ǯǦ41IC=ECD81F5D853EB9>73?=@?E>4
removed prior to application of surface preparation adhesive and pavement markings.
b. “N” Series tape application requires four passes of SPA60 to the road surface and four passes to
the back of the tape.
c. ?B5=1B;9>7C9>=9>9=1<DB1ɣ31B51C9>3<E457?B5C1D8978G1I?>B1=@C1>4?ɢB1=@CG85B5
=9>9=1<DB1ɣ33B?CC5C?F5BD85@1F5=5>D=1B;9>7C
d. ?B5=1B;9>7C9>851FIDB1ɣ31B51C9>3<E4581D3854=5491>1B51C1<?>7EB21>B?14G1ICG85B5
8978<5F5<C?6DB1ɣ33B?CC?F5BD85@1F5=5>D=1B;9>7
e. # ǬǦ?B ǫǦ=1I25EC546?B7?B51B51CG9D8=9>9=1<D?>?3B?CC?F5BDB1ɣ3
f. SPA60 or P-50 are the only surface preparation adhesives recommended for use with Series
380AW, 390, 380I ES and 270 ES tapes for transverse marking application.
#55@@5>49H6?B7E941>35?>D85EC5?6# ǬǦ1>4 ǫǦ21C54?>B?14DI@5
ǧ 5D5B=9>5B?14CEB61353?>49D9?>C
a. 6CEB61359C>5G3?>3B5D5?@5>D?DB1ɣ3<5CCD81>ǯǦ41ICB5=?F53EB9>73?=@?E>42I<978D
grinding, sandblasting, shotblasting or hydroblasting.*
b. If markings exist on the roadway, remove markings from the surface by grinding, sandblasting,
shotblasting or hydroblasting.* A minimum of 90 percent of the road surface under the existing
markings must be exposed prior to tape application.
?D5I4B?2<1CD9>7B5AE9B5C1ǨǪ8?EB4BI9>7@5B9?4256?B5D1@51@@<931D9?>
ǧǪ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
Ǩ <51>D85B?14
Clean the surface of the road where the tape will be applied. Clean the
road surface using high velocity, high pressure compressed air blower with
=9>9=E=ǧǮǫ36=19Bɦ?G1>4ǧǨǦ@C91DD8519B>?JJ<5B53?==5>454$85
road surface must be dry.
ǩ B5=1B;D85B?14
Layout the area where the marking will be applied.
Ǫ 5D5B=9>596CEB6135@B5@1B1D9?>1485C9F59CB5AE9B54
#55@175ǩ?B1449D9?>1<9>6?B=1D9?>?>1@@<931D9?>B565BD?D85
@B?4E3D2E<<5D9>6?BD85D1@5259>71@@<954
a. If no adhesive is required, go to Step 11.
b. If adhesive is required, go to Step 5.
ǫ #D9BD851485C9F5
Stir and thoroughly mix the SPA60 or P-50 adhesive with a wide wooden
@19>D@144<5?B19B4B9F5>@19>D=9H5B?BB?<<E>?@5>54ɥF571<<?>@19<213;
and forth several times until adhesive is thoroughly mixed. 1;5CEB51>I
C549=5>D?>D852?DD?=?6D85ɥF571<<?>3?>D19>5B9C3?=@<5D5<ICD9BB54
9>D?13?>C9CD5>DC?<ED9?> (See Figure 15.)
97EB5ǧǫ
Ǭ @@<ID851485C9F5
a. If using SPA60 or P-50 adhesive on asphalt four to ten days old, see Step
5 on Page 10.
b. If using SPA60 or P-50 for an intersection or transverse maBking -
including legends and symbols - evenly apply one coat of adhesive to
the road surface using a solvent-resistant roller with a minimum 3/8-
inch nap to a maximum 3/4-inch nap. The coating on the pavement
must extend at least one inch (2.5 cm) beyond the premarked area. (See
Figure 16.)
SPA60 or
P-50 adhesive
97EB5ǧǬ
ǭ <<?GD851485C9F5D?C5D
a. Allow the P-50 to set. P-50 is set
when it feels tacky but is no longer
9><9AE946?B=1>481C1=1DD5ɥ>9C8
rather than a glossy wet appearance.
P-50 dries quickly (to a set state)
under most circumstances. Typical
time for P-50 to set is two to three
minutes under optimal conditions
of 70°F (21°C) and medium to
low humidity levels. For more
information on P-50 application
procedures see Information Folder
5.17. (See Figure 17.)
97EB5ǧǭ
b. Allow SPA60 to dry. SPA60 is
dry when it no longer feels tacky.
BID9=59C1@@B?H9=1D5<IɥF5
minutes. Lower temperatures and
higher humidity will increase dry
times. For more information on
SPA60 application procedures see
Information Folder 5.21.
ǧǫ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
Ǯ "5=1B;D85B?1496>55454
ǯ 5D5B=9>5>5HDCD5@21C54?>D1@51485C9F5C5B95C259>7EC54
a. If tape is Adhesive Series A (with adhesive), go to Step 11.
b. If tape is Adhesive Series L (with adhesive and a liner), then go to Step 11.
c. If tape is Adhesive Series N (no adhesive and no liner), go to Step 10.
ǧǦ485C9F5#5B95CD1@5G9D8>?1485C9F5?B<9>5B?><ISpray apply four passes of
SPA60 to the road surface and apply four passes to the back of the tape with the SPA60
spray cylinder.
$'89<5C@B1I9>74EB9>7D856?EB2I6?EB@1CCCICD5=9D9C1<<?G54D?C@B1IDG?<978D@1CC5CD?D85B?14CEB6135
1>4DG?<978D@1CC5CD?D85213;?6D85D1@5<<?GD8B55D?ɥF5=9>ED5CD?4BI1D>?B=1<3?>49D9?>C?6ǭǦǹǨǧǹ
??<5BD5=@5B1DEB5C=1IB5AE9B5<?>75B4BI9>7@5B9?46D5B4BI@5B9?4B5C@B1IDG?=?B5@1CC5C?>B?141>4DG?
=?B5@1CC5C?>213;?6D85D1@5$89CG9<<1<<?GD85# ǬǦ1485C9F5D?4BI61CD5B1>4C5DE@5F5><I6?B3?BB53D2?>4
# ǬǦ9CC5D?>35D851485C9F59CD13;6B55G8938D1;5C1@@B?H9=1D5<IɥF5=9>ED5C45@5>49>7?>19BD5=@5B1DEB5
1>48E=949DI#5DD9=5G9<<381>7545@5>49>7?>3<9=1D53?>49D9?>C
=@?BD1>D?D5<G1IC3853;9>49ɢ5B5>D1B51C1>45C@5391<<I45@B5CC9?>C9>D85B?14CEB6135G85B5=?B5# ǬǦ
?B ǫǦ=1I25@B5C5>D1>4C<?G5BD?4BI
ǧǧ @@<ID85D1@52I81>4
Apply the tape by hand. When splicing is required, do not overlap the material. Use butt splices.
(See Figure 18.)
97EB5ǧǮ
?D56D85B59C13B13;9>D85B?14D81D31EC5CD85D1@5D?2B9475<1ID85D1@5?F5BD853B13;D1=@D85D1@51>4
D85>3EDD85D1@5?>59>386B?=5138C945?6D853B13;#5597EB5ǧǯ
97EB5ǧǯ
Use this same technique on concrete when the transverse marking is applied over a joint: Cut
the tape one inch back from each side of the joint.
For material with liner (Adhesive L Series): Refer to IF 5.8 for liner removal techniques.
Position the marking and peel back the liner. Press the exposed tape down. Slowly remove the
rest of the liner as the tape is carefully guided into place. Refer to IF 5.8 for liner removal.
ǧǬ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
ǧǨ$1=@D85D1@5&") "$$
Tamp the tape thoroughly with the RTC-2 tamper cart with a minimum 200-
lb. (90-kg) load making a minium of six passes. (See Figure 20.)
97EB5ǨǦ
• Do not twist or turn the tamper cart on the tape.
• Make a minimum of six passes (three passes back and forth) over each
part of the tape.
• If tape is wider than the roller, more passes will be needed to make
sure the entire width of the tape has received the required tamping
treatment. $ #$#$ "$$#$ $
$  $ "##
• 1;5CEB51<<5475C1B5ɥB=<I1485B54
?D5?>?DEC51F5893<5D9B5D?D1=@DB1>CF5BC5=1B;9>7C
ǧǩ@5>D85B?14D?DB1ɣ3
449D9?>1<>6?B=1D9?>
 #D?B175
Surface preparation adhesive SPA60 and P-50 must be stored in a cool,
dry area indoors. A storage temperature of 40-100ºF (4-38ºC) is
recommended. Use all tape products within one year of receipt. Unopened
containers of SPA60 or P-50 must be used within two years of receipt.
Check lable for expiration date of receipt.
 "5=?F1<
Stamark durable tapes are designed for permanent, non-removal
applications. Contact your 3M representative for guidance concerning
removal of Stamark tapes.
51<D81>4#165DI
BI@1F5=5>D@B5@1B1D9?>D538>9AE5C4BI7B??F9>7=5D8?4C1>44BI
7B??F53<51>9>7=5D8?4C1B5B53?==5>454D??@D9=9J5@1F5=5>D
=1B;9>7D1@51485C9F5@5B6?B=1>351>4D?6139<9D1D59==5491D5@1F5=5>D
=1B;9>71@@<931D9?>G9D8?EDD85>5546?B1ǨǪ8?EB4BI9>7@5B9?4
<G1IC6?<<?G1@@<9312<5D5=@?B1BI
DB166933?>DB?<@B?354EB5C1>4C165
G?B;J?>5@B13D935C?B5H1=@<55I5
51BB5C@9B1D?BI?B?D85B@B?D53D9?>
=1I251@@B?@B91D54EB9>77B??F9>7
CEB6135@B5@1B1D9?>?B6?BD85B5=?F1<
?65H9CD9>7@1F5=5>D=1B;9>7C?B
B5C@9B1D?BI@B?D53D9?>B5AE9B5=5>DC
@<51C5B565BD?D85#"5C@9B12<5
BICD1<<9>5#9<931#D1>41B41>4D85
#=1<<>D9DI?=@<91>35E9456?B
"5C@9B12<5BICD1<<9>5#9<931#D1>41B4
6?B?>CDBE3D9?>1DGGG?C817?F6
G5D7B9>49>7?B7B??F9>7@B?354EB5C
9>3<E49>7D8?C5<9CD549>$12<5ǧ?6D85
12?F5#CD1>41B41B5EC54D85
7B??F5=ECD253<51>549==5491D5<I
G9D88978@B5CCEB5G1D5BC@B1ID?
@B5F5>DD8535=5>D4ECDG1D5BC<EBBI
6B?=81B45>9>79>D857B??F51>41ǨǪ
8?EB4BI9>7D9=59CB5AE9B54@B9?BD?D85
9>CD1<<1D9?>?6D85D1@5
"5141<<851<D881J1B4@B531ED9?>1BI
1>469BCD194CD1D5=5>DC6?E>49>D85
#165DI1D1#855D##1>4?B
@B?4E3D<125<?6385=931<C@B9?BD?
81>4<9>7?BEC5<C?B565BD?##C6?B
9>6?B=1D9?>B571B49>7D85F?<1D9<5
?B71>933?=@?E>4&3?>D5>DC?6
385=931<@B?4E3DC?>CE<D<?31<
B57E<1D9?>C1>41ED8?B9D95C6?B@?CC92<5
B5CDB93D9?>C?>@B?4E3D&3?>D5>DC
1>4?B&5=9CC9?>C<53DB?>931<<I
F9C9DEC1DGGGǩ3?=EC1>45>D5B
##C51B38
1ED9?>
• Gloves should be worn when using
any Stamark tapes to prevent injury
to hands.
• ?>?DEC51ɦ1=5?BD?B38D?
remove Stamark tapes. Burning may
violate local, state or federal air
quality regulations. Also, exposing
the tape to very high temperatures
G9D8D85EC5?61ɦ1=5?BD?B38
could generate emissions that
may be harmful to skin, eyes and
respiratory system.
ǧǭ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
@@5>49H 1F5=5>D#EB6135$I@5C
The pavement surface type and age determine which application
procedures should be used for Stamark tapes. For pavement types not
covered, contact your 3M representative.
 # $$"$
#D1>41B49HC@81<D
CD1>41B4=9H3?>D19>C2?D8ɥ>5C1>41>4<1B75ǧǪ9>38+Ǭ==-
aggregate with an asphalt cement binder. Stamark tapes can be inlaid or
overlaid on this surface.
@5>B145B93D9?>?EBC5
An open grade friction course mix consists of only large aggregate, up to
3/4 inches (19 mm), with an asphalt cement binder. Stamark tapes can be
inlaid or overlaid on this surface. Refer to the inlay application section of this
folder for further explanation, beginning on page 4.
89@#51<
A chip seal is achieved by spraying a hot asphalt emulsion onto an existing
surface and then covering it with a 1/4-inch (6.4-mm) aggregate. Excess
177B571D59CB5=?F5416D5BC5F5B1<41IC?65H@?CEB5D?DB1ɣ3#D1=1B;
tapes can be overlaid on this surface after the loose aggregate is removed
and the surface has cured.
#<EBBI#51<
A slurry seal is a hot asphalt emulsion that is sprayed onto an existing
surface, as a top coat dressing only. No aggregate is added. Stamark tape
31>25?F5B<194?>D89CCEB613516D5BD85B?1481C255>?@5>D?DB1ɣ36?B
three days.
"53I3<54C@81<D
This road surface consists of an existing asphalt that is removed through
milling or grinding, reprocessed and then reapplied. Stamark tape can be
inlaid or overlaid on this surface.
"E225B9J54C@81<D
Rubberized asphalt mixes contain additives designed to increase durability.
The mix can be either a “standard mix” or an “open grade friction course”
mix. Stamark tape can be applied as noted under the appropriate headings
in this information folder.
 "$$"$ 
5G?>3B5D5
During construction, the new surface is often brushed or grooved (tined).
?>3B5D5D81D81C255>?@5>D?DB1ɣ3<5CCD81>ǯǦ41IC=ECD81F5D85
curing compound removed before applying Stamark tapes or surface
preparation adhesive. Sandblasting is
the method commonly used to remove
curing compound from new concrete.
Other methods, such as shotblasting or
hydroblasting, can also be used. In the
case of hydroblasting, the pavement
must be allowed to dry before the
surface preparation adhesive and tape
are applied.
<4?>3B5D5
Old concrete is a PCC surface that
81C255>?@5>D?DB1ɣ36?B=?B5D81>
one year and is showing signs of wear.
Often this surface is smooth with
large amounts of exposed, polished
aggregate. Stamark tape can be
overlaid using a surface preparation
adhesive. The old concrete surface
may require texturing prior to surface
preparation adhesive and tape
application. Contact a technical service
representative at 1-800-553-1380 for
additional information.
ǧǮ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
@@5>49H#EB6135 B5@1B1D9?>485C9F5C
Two surface preparation adhesives are commonly available for application of Stamark pavement
marking tapes: surface preparation adhesive SPA60 and P-50.
 #EB6135 B5@1B1D9?>485C9F5# ǬǦ
# ǬǦ31>25EC549>1ɥF571<<?>@19<?BC@B1I3I<9>45B6?B<?>7<9>51>4DB1>CF5BC5
applications. SPA60 can be applied using a spray or roller method.
 #EB6135 B5@1B1D9?>485C9F5 ǫǦ
P-50 sprayable adhesive is applied using the PS-14 spray applicator. It is designed to be used as
a surface preparation adhesive for long-line applications. It is also applied using a long-handled,
thick (3/8 inch [0.95cm]) nap paint roller with a solvent resistant core.
 ?F5B1756?B# ǬǦ1>4 ǫǦ485C9F5C
#5581BDǩ25<?GD?45D5B=9>58?G=E381485C9F5I?E>554D?3?F5B1C@539ɥ31B51
485C9F5$I@5 >5?1D
SPA60 Roller
Application
SPA60 roller application recommends one even coat on the road surface of adhesive series A series
tapes. Please calculate the square footage per road surface and back of the tape.
SPA60 Coverage of 1500 sq. ft. per cylinder (mini 26 lbs). 3000 linear feet per cylinder for 4-inch tape
(spraying 6” wide SPA60).
Coverage of 225 sq. ft. per gallon. 450 lineal feet per gallon for 4-inch tape (spraying 6 inches wide
SPA60). 337.5 lineal feet per gallon for 6-inch tape (spraying 8 inches wide SPA60.)
P-50 Surface
Preparation
Adhesive Spray
Application
P-50 Coverage of 225 sq. ft. per gallon. 450 lineal feet per gallon for 4-inch tape (spraying 6 inches
wide P-50). 337.5 lineal feet per gallon for 6 inch tape (spraying 8 inches wide P-50.)
P-50 Roll
Application
75 sq. ft/gallon (1.8 sq. m/liter)
(3/8 inch Nap) metric
ǧǯ
ǩūStamar;ū Tapes Pavement Surface Preparation and Application Techniques 1>E1BIǨǦǧǮ
@@5>49H"?14$I@5#EB6135 B5@1B1D9?>485C9F5
@@<931D9?>"53?==5>41D9?>C
"?14<1>5C1B5DI@931<<I5H@?C54D?49ɢ5B5>D<5F5<C?6DB1ɣ3C851B5H@?CEB5"?14<1>5CD81D1B5
exposed to a high frequency of high shear turning; especially by trucks and other large vehicles
require use of surface preparation adhesive SPA60 or P-50 for application of Stamark pavement
marking tapes. The following table summarizes the product and surface preparation adhesive
application recommendations by shear condition:
#851B5F5< B?4E3D1>4485C9F5"53?==5>41D9?>
Very High Shear
Stamark Tape “N” Series
Using the SPA60 spray cylinder
High Shear
Stamark Tape Adhesive Series “A” and “L” Stamark Series
Use One Coat of SPA60 or P50
Moderate Shear
Stamark Tape “A” and “L” Stamark Series
Use SPA60 or P-50
Low Shear
Stamark Tape “A” and “L” Series
No surface preparation adhesive required unless
otherwise directed by 3M technical service.
Within the Climate Guide and road condition recommendations
=@?BD1>D?D5"565BD?F5B<1I@@<931D9?>?6$B1>CF5BC51B;9>7CC53D9?>CCD1BD9>7?>@175ǧǩ?>D13Dǩ
$538>931<#5BF9351DǧǮǦǦǫǫǩǧǩǮǦ6?BAE5CD9?>C?># ǬǦ?B ǫǦ1@@<931D9?>C
9D5B1DEB5"565B5>35
?B1449D9?>1<9>6?B=1D9?>?>ǩ
™
#D1=1B;
™
 1F5=5>D1B;9>7$1@5C1@@<931D9?>
B53?==5>41D9?>C?Bǩ1@@<931D9?>5AE9@=5>DB565BD?D856?<<?G9>7@E2<931D9?>C
Product Bulletin 380AW 3M
™
Stamark
™
High Performance All Weather Tape Series 380AW
Product Bulletin 380I ES 3M
™
Stamark
™
High Performance Tape Series 380IES
Product Bulletin 380I-5ES 3M
™
Stamark
™
High Performance Tape Series 380I-5ES
Product Bulletin 270 ES 3M
™
Stamark
™
Pavement Marking Tape 270ES
Product Bulletin 390 3M
™
Stamark
™
High Performance Tape Series 390
Product Bulletin 390-5 3M
™
Stamark
™
High Performance Contrast Marking Tape
Information Folder 5.2 Highway Tape Applicator (HTA)
Information Folder 5.8 Application of 3M
™
Stamark
™
Precut Symbols and Legends
IInformation Folder 5.17 3M
™
Stamark
™
Surface Preparation Adhesive P-50
Information Folder 5.18 Guidelines for Pavement Marking Applications in Grooved
Information Folder 5.21
3M Climate Guide
3M Road Surface Guide
Pavement Surfaces
3M Stamark Surface Preparation Adhesive SPA-60
Climate Guide for 3M
™
Stamark
™
Pavement Marking Tapes
Road Surface Guide for 3M
™
Stamark
™
Pavement Marking Tapes
Personal Safety Division's Tips for New OSHA Silica Regulations
3M PSD
For Information or
A
ssistance
Call:
1-800-553
-
1380
In Canada
Call:
1
-800-3M HELPS (1-800-364-3577)
Interne
t:
http://www.3M.com/roadsafety
3M 3M Science. Applied to Life.1>4#D1=1B; are trademarks of 3M. Used under license in Canada.
3M assumes no responsibility for any injury, loss, or damage arising out of the use of a product that is not of our
manufacture. Where reference is made in literature to a commercially available product, made by another
manufacturer, it shall be the user’s responsibility to ascertain the precautionary measures for its use outlined by
the manufacturer.
Transportation Safety Division
3M Center, Building 0225-04-N-14
St. Paul, MN 55144-1000 USA
Phone 1-800-553-1380
Web
3M.com/roadsafety
Please recycle. Printed in USA © 3M 201Ǯ.
All rights reserved. Electronic Only
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

3M Stamark™ High Performance Tape Series 380AW Operating instructions

3M
Brand
3M
Model
Stamark™ High Performance Tape Series 380AW
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents