Elo 1903LM User guide

Category
Touch screen monitors
Type
User guide

Elo 1903LM is a 19-inch touch monitor designed for use in high-traffic environments. It features a 24-bit color active matrix thin-film-transistor LCD panel for high-quality display performance, a 1280 x 1024 resolution, and a 0.5ms response time. The monitor also has a built-in projected capacitive touch screen that supports up to 10 touches at once, making it ideal for use with interactive applications. Additionally, the Elo 1903LM has a variety of connectivity options, including HDMI, VGA, USB, and audio, making it easy to connect to a variety of devices.

Elo 1903LM is a 19-inch touch monitor designed for use in high-traffic environments. It features a 24-bit color active matrix thin-film-transistor LCD panel for high-quality display performance, a 1280 x 1024 resolution, and a 0.5ms response time. The monitor also has a built-in projected capacitive touch screen that supports up to 10 touches at once, making it ideal for use with interactive applications. Additionally, the Elo 1903LM has a variety of connectivity options, including HDMI, VGA, USB, and audio, making it easy to connect to a variety of devices.

USER MANUAL
Elo Touch Solutions
ET1903LM, ET2203LM, ET2403LM, ET2703LM
UM600152 Rev B
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
2
Copyright © 2018 Elo Touch Solutions, Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or
by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) make no representations or warranties
with respect to the contents herein, and specifically disclaim any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to revise
this publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes.
Trademark Acknowledgments
Elo, Elo (logo), Elo Touch, Elo Touch Solutions and TouchPro are trademarks of Elo and its Affiliates. Windows is a trademark of Microsoft Corporation.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
3
Table of Contents
Section 1: Introduction ............................................................................................................................................................................................................................... 4
Section 2: Installation ................................................................................................................................................................................................................................. 5
Section 3: Mounting ................................................................................................................................................................................................................................... 8
Section 4: Operation ................................................................................................................................................................................................................................ 14
Section 5: Technical Support ................................................................................................................................................................................................................... 15
Section 6: Safety & Maintenance ............................................................................................................................................................................................................. 17
Section 7: Regulatory Information ............................................................................................................................................................................................................ 18
Section 8: Warranty Information............................................................................................................................................................................................................... 26
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
4
Section 1: Introduction
Product Description
Your new touch monitor combines the latest developments in touch technology and display design with reliability for use in high-traffic
environments.
This touch monitor incorporates a 24-bit color, active matrix thin-film-transistor LCD panel to provide high-quality display performance. The 03 Series
includes full sizes from 19 to 27 inches and supports resolutions from 1280 x 1024 to full HD 1920 x 1080. Its LED backlight significantly reduces power
consumption and eliminates the need for mercury (compared to CCFL-backlit panels). Other features that enhance this LCD monitor’s performance are
Plug & Play compatibility, remote on-screen display (OSD) controls and flexible mounting options.
The monitor is intended for use with a self-check-in/registration or point-of-information system for the general environment or medical clinic, or
displaying/reviewing the health information or record. The subject equipment monitor is powered by an externally recognized AC/DC adaptor.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user manual to maximize the life of your unit and prevent risks to user safety.
See the Safety & Maintenance Section for more information.
This manual contains information that is important for the proper setup and maintenance of the unit. Before setting up and powering on your new touch
monitor, read through this manual, especially the Installation, Mounting, and Operation Sections.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
5
Section 2: Installation
Unpacking the Touch Monitor
Open the carton and verify that the following items are present:
Touch monitor with stand
Japanese-language regulatory information pamphlet
Quick Install Guide
VGA cable
HDMI cable
USB cable
Audio cable
Power brick
Europe power cord
North America power cord
3 x tie wraps
EEI Label
2 x cable cover screws
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
6
Connector Panel
Note: Cable tie-down points can be used to tie down the cables with tie wraps. Simply loop the tie wraps through the cable tie-down points and around the
cable to secure cable connections.
Touch Monitor Connections
1.
Connect one end of the HDMI or VGA video cable to the monitor’s HDMI/VGA input connector and the
other end to your HDMI/VGA video source. (Tighten the video cable’s screws on the VGA connector for
best performance.)
2.
Connect the USB touch cable between the monitor’s USB connector and your PC’s USB port.
3.
Connect the audio cable between the monitor’s Audio Out and your audio source.
4.
Connect the power adaptor’s input connector to the power source. Connect the power adaptor’s DC output connector to the monitor’s input power jack.
5.
The touch monitor ships in an OFF state. Press the power button to turn it on.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
7
Installing the Touch Technology Software Drivers
No additional drivers are required for your projected-capacitive touch monitor with Windows 7, 8 or 10 operating systems, as it will use the Windows HID
drivers. If the monitor is used with the Windows XP operating system, follow the steps below to install the Windows XP touch driver.
To download the latest touch drivers:
1.
Visit www.elotouch.com/Support/Downloads/Driver/DriverDownload/Default.aspx
2.
Select the operating system from the Operating System drop-down menu.
3.
Select the technology from the Technologies drop-down menu.
4.
Download the driver version required for your touch monitor.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
8
Section 3: Mounting
Rear VESA Mount
A four-hole 100 x 100 mm mounting interface for M4 screws is provided on the rear of the monitor. Remove the stand using a Phillips screwdriver to
access the mounting interface. The VESA FDMI-compliant counting is coded VESA MIS-B, 75, C and VESA MIS-D, 100, C.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
9
Base Mount
The VESA FDMI-compliant counting is coded VESA MIS-E, C.
ET1903LM & ET2203LM base mounting options are shown below.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
1
0
ET2403LM & ET2703LM base mounting options shown below.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
1
1
Magnetic Stripe Reader (MSR) Installation (Optional)
Your monitor comes with four pheripheral ports, located at the top, bottom, left and right sides of the monitor. To mount an MSR, remove one of the
pheripheral port covers with your finger tips and install the MSR as shown below. Please refer to the MSR Quick Install Guide (QIG) for set-up details.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
1
2
Wall Mount
Mount the wall bracket to the wall using six fasteners appropriate for the type of wall material and following all applicable building code standards.
Ensure the unit is mounted to a solid structure and surface, such as a support beam or wall.
Attach the other bracket to the monitor using the four M4 screws included in the kit.
Hang the monitor on the wall bracket and secure using two M3 screws included with the kit on the left and right side of the bracket.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
1
3
Handles Installation (Optional)
Optional handles can be installed on 03 Series monitors, as shown below. Please note that it is not recommended to use handles to carry the touch
monitor. Damage to the touch monitor will occur if the touch monitor is lifted by the handles. Use handles only to adjust the tilt angle.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
1
4
Section 4: Operation
Power
To turn the touch monitor on or off, press the touch monitor’s power button once.
The Power Status LED on the bottom of the touch monitor functions as follows:
Touch Monitor Status
LED Status
OFF
OFF
SLEEP
PULSING (Orange)
ON
ON ( Green)
The system consumes low power when in SLEEP or OFF modes. For detailed power-consumption specifications, refer to the technical
specifications on the Elo website http://www.elotouch.com
Touching the screen will bring the attached host PC out of SLEEP mode (similar to moving the mouse or pressing a keyboard key).
To improve reliability and reduce wasteful power consumption, disconnect the AC power cable from the monitor when long periods of disuse are planned.
Touch
No calibration is required for projected capacitive touch technology. Your touch monitor can support up to 10 touches at once.
Note: When using a privacy filter with your monitor, it is important to update the touch configuration file of you monitor to support touch.
If you are using an ET1903LM/ET2203LM monitor, the touch-through configuration file is already built into your monitor. Simply go to the OSD menu and
enable the touch-through function. Do not forget to disable the touch-through function when using the monitor without a privacy screen.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
10
Projected Capacitive Touch Technology
When connected to Windows 7, 8 or 10 computers, the touch monitor can detect 10 simultaneous touches. When connected to Windows XP computers,
the touch monitor detects only single touches.
No additional drivers are required for this technology to work with Windows 7, 8 or 10, as it uses Windows HID drivers.
Refer to Section 2, “Installing the Touch Technology Software Drivers,for instructions on downloading touch drivers for Windows XP.
No calibration is required for this technology.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
11
Gesture Support
TouchPro PCAP technology enables several gestures that support single and multiple touches. Refer to the Microsoft website at
http://msdn.microsoft.com/en-us/library/dd940543 on the various gestures that are supported in Windows 7, 8, 10
and later OS versions.
Video
A display’s native resolution is its width and height measured in pixels. Generally, for best performance, an image displayed on this monitor will look best
when your computer’s output resolution matches this monitor’s native resolution, which is 1280 x 1024 for the 1903L and 1920 x 1080 for the 2203L, 2403L
and 2703L monitors
For computer output at non-native resolutions, the monitor will scale the video to its panel’s native resolution. This involves stretching or compressing the
input image as needed in the X and Y dimensions to fit the display’s native resolution. An unavoidable byproduct of the scaling algorithms is a loss of
fidelity when the computer’s output video image is scaled by the monitor to fit the display. This loss of fidelity is most apparent when viewing feature-rich
images at close distances (e.g., images containing small-font text).
Your touch monitor will likely not require video adjustments. However, for analog VGA video, variations in video graphic card outputs may require user
adjustments through the OSD to optimize the quality of the touch monitor’s displayed image. These adjustments are stored by the touch monitor. Also, to
reduce the need for adjustments for different video mode timings, the monitor correctly scales and displays some of the video industry’s most common
video timing modes. Refer to the technical specifications for this monitor at http://www.elotouch.com for a list of these Preset Video Modes.
On-Screen Display (OSD)
Five OSD buttons are located on the rear of the monitor. These can be used
to adjust various parameters. The buttons and their functionalities are:
Function when OSD is not displayed
Function when OSD is displayed
Display OSD Main menu
Return to previous OSD menu
Display OSD Contrast submenu
Decrease value of selected parameter/select previous menu item
Display OSD Brightness submenu
Increase value of selected parameter/select next menu item
Display Video Priority submenu
Select parameter for adjustment/select submenu to enter
Power key
Power on/off display
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
12
The OSD buttons control an on-screen graphical user interface that overlays your input video, allowing the following adjustments:
Parameter
Available Adjustment
Brightness
Increases/decreases monitor brightness.
Default: maximum
Contrast
Increases/decreases monitor contrast.
Default: best gray-shade performance
Clock
Allows fine adjustments of the panel’s pixel dot clock.
Applicable for VGA input video only.
Phase
Allows fine adjustments of the panel’s pixel dot clock phase.
Applicable for VGA input video only.
Auto Adjust
Automatically adjusts the system clock to the input analog VGA video signal, affecting the H-position, V-position, Clock, and Phase menu items.
Applicable for VGA input video only.
H-position
Moves the image horizontally on the display in single-pixel increments.
Default: centered
Applicable for VGA input video only.
V-position
Moves the image vertically on the display in single-pixel increments.
Default: centered
applicable for VGA input video only.
Aspect Ratio
Switches the scaling method between Full Scaling and Maintain Aspect Ratio. Default:
Full Scaling
Full Scaling: Scales the X and Y dimensions of the input video (up or down as needed) to the display’s native resolution.
Fill to Aspect Ratio: Assuming a landscape orientation and an input video with aspect ratio smaller than 16:9, scales the Y dimension of the input video (up or down
as needed) to the display’s Y resolution, scales the X-dimension to maintain the input videos aspect ratio, and fills the rest of the display with equal black bars on the
left and right.
Other touchscreen technologies may need recalibration when switching between Aspect Ratio options.
Sharpness
Adjusts sharpness of the displayed images.
Default: no sharpness adjustment
Applicable at non-native input video resolutions only.
Color Temperature
Selects the displays color temperature. The available color temperatures are 9300K, 7500K, 6500K, 5500K and User Defined. If the User Defined option is
selected, the user can change the color temperature by changing individual R, G, and B gains on a scale from 0 to 100. Default: User Defined with R, G, and B
all set to 100.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
13
Parameter
Available Adjustment
OSD H-Position
Adjusts the horizontal location of the OSD menus on the display. Default: centered
OSD V-Position
Adjusts the vertical location of the OSD menus on the display. Default: centered
OSD Timeout
Adjusts how long the touch monitor will wait without OSD button activity before closing the OSD. The adjustable range is between 5 and 60 seconds.
Default: 15 seconds
OSD Language
Selects the OSDs display language. The available languages are: English, French, Italian, German, Spanish, Simplified Chinese, Traditional Chinese, and Japanese.
Default: English
Recall Defaults
Restores all factory default settings for OSD-adjustable parameters (except OSD Language) and for Preset Video Mode timings.
Video Priority
The monitor continually scans for active video on the VGA and HDMI connectors.
This adjustment selects which of those input ports should be given the priority for display.
The options are: VGA Priority, HDMI Priority.
Default: HDMI Priority
Audio
Audio menu enables users to switch between audio sources. When HDMI is plugged in, internal speakers can be used by changing the audio source
to HDMI. This menu includes the headphone feature as well, which will allow users to plug in an external audio source when using HDMI. When using
the VGA Line in option, it can be used to enable internal speakers.
Power LED
Option to turn the power LED ON/OFF.
Default: On
Touch Through
Enables touch capabilities when using privacy filters.
Applicable for 19”/22” monitors only
All touch monitor adjustments made through the OSD are automatically memorized as soon as they are modified.
This feature prevents having to reenter the settings every time the touch monitor is unplugged or powered off.
In case of a power failure, the touch monitor settings will not default to the factory specifications.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
14
OSD and Power Lockouts
Press and hold the “Menu” and “ ” buttons simultaneously for two seconds to enable/disable the OSD Locking feature. When OSD Locking is enabled,
pressing any of the Menu, Up, Down or Select keys will have no effect.
Press and hold the “Menu” and “ ” buttons simultaneously for two seconds to enable/disable the Power Locking feature. When Power Locking is
enabled, pressing the power switch will have no effect.
User Manual ET1903LM, ET2203LM, ET2403LM, ET2703LM
15
Section 5: Technical Support
If you are experiencing trouble with your touch monitor, refer to the following suggestions.
If the problem persists, please contact your local dealer or contact Elo Touch Solutions Customer Service. Worldwide technical support phone numbers
are available on the last page of this user manual.
Solutions to Common Problems
Problem
Suggested Troubleshooting
The touch monitor does not respond when turning on
the system.
Check that the DC power adaptor is properly connected. Verify the
DC power adaptor is functioning
Monitor display is dim.
Use the OSD to increase the brightness.
Use the OSD to increase the contrast.
Monitor display is blank.
If the Power Status LED is blinking, the monitor or Computer Module may be in SLEEP mode. Press
any key/move the mouse/touch the touchscreen to see if the image reappears. Check that the signal
source device is turned on.
Check that that there are no loose cable connections.
Monitor displays the Out of Range” message.
Adjust your computer’s resolution/timing mode to be within the allowable timing ranges
specified for your touch monitor (see website for specifications).
Monitor display image looks strange.
Adjust your computer’s resolution/timing mode to be within the allowable timing ranges
specified for your touch monitor (see website for specifications).
Use the Auto Adjust function in the OSD.
Touch functionality doesn’t work.
Verify your PC has the latest Elo drivers installed.
Perform the calibration routine provided with the latest Elo drivers.
Neither the OSD nor power buttons
responds when pressed.
Check to see if the OSD lock or power lock functions are on.
No touch, or touch is not accurate when using
privacy filters.
Check if the touch-through mode is enabled for 19”/22” monitors.
Monitor turns off by itself.
If the monitor turns off by itself, it could be due to a voltage drop (to below 10 V) in the building. The
monitor will turn itself back on once it receives minimum 11 V of power.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35

Elo 1903LM User guide

Category
Touch screen monitors
Type
User guide

Elo 1903LM is a 19-inch touch monitor designed for use in high-traffic environments. It features a 24-bit color active matrix thin-film-transistor LCD panel for high-quality display performance, a 1280 x 1024 resolution, and a 0.5ms response time. The monitor also has a built-in projected capacitive touch screen that supports up to 10 touches at once, making it ideal for use with interactive applications. Additionally, the Elo 1903LM has a variety of connectivity options, including HDMI, VGA, USB, and audio, making it easy to connect to a variety of devices.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI