OWNER’S MANUAL
FORM: OM-6617 220 643D
2007−04
Use above FORM number when ordering extra manuals.
Running Gear No. 38 (195 352) For Champ
)
4500, Blue Star
)
145 And 185, And Renegadet 180 Models
Follow the instructions below to install the running gear on all Champ 4500 models
and Blue Star 145 and 185 models with two base mounting holes on generator end.
NOTE
Warning! Watch Out! There are possible hazards as
shown in the adjoining symbols.
Beware of electric shock from wiring. Stop engine and
disconnect negative (−) cable from battery before install-
ing this kit. Reinstall all panels and covers.
Wear safety glasses with side shields. Falling equipment can cause serious personal injury and
equipment damage. Use lifting eye to lift unit only, not
trailer, gas cylinders, or any other accessories. Use
equipment of adequate capacity to lift unit or parts such
as engine or generator.
803 851-C
Tools Needed:
Item Description (Qty)
1 218659 Handle, Running Gear w/Grip (2)
211340 Grip, Handle 1.062 Id x 5.000
Black Soft Foam (1)
2 602241 Washer, Flat .281idx0.625odx.065t
Stl Pld Ansi.250 (8)
3 601865 Nut, 250−20 .44hex .21h Stl Pld (8)
4 218327 Bracket, Mtg Axle (2)
5 601941 Screw, 250−20x1.75 Hexwhd.61d
Gr5 Pld (4)
6 145665 Ring, Rtng Ext 1.000 Shaft x .052
Thk E Style Pld (2)
7 602251 Washer, Flat1.062idx2.000odx.134t
Stl Pld Ansi 1.00 (2)
8 022825 Wheel, w/Tire&brg, 8 In Tire W/1 In
Brg (2)
9 188397 Axle, Running Gear 1.000 Dia x
31.947 (1)
10 211341 Crutch Tip (1.062 I.d.) (2)
11 084499 Screw, 250−20x2.75 Hex Hd−pln
Stl Pld Grd 5 (4)
12 602207 Washer, Lock .255idx0.489od
x.062t Stl Pld Split.250 (8)
. Remove paint
from axle grooves
before installing
retaining rings.
1
2
3
3
2
4
5
6
7
8
9
10
11
12
12
Part No.
. Be sure to provide
model and serial num-
ber when ordering
replacement parts.
Two base
mounting
holes.
For all Champ 4500 models and Blue Star 145/185 models with two base
mounting holes on generator end.
OM-6617 Page 2
Follow the instructions below to install the running gear on Blue Star 145 and 185
models with three base mounting holes on engine end (see illustration), and all
Renegade 180 models.
NOTE
803 851-C
Tools Needed:
Description (Qty)
1 218659 Handle, Running Gear w/Grip (2)
211340 Grip, Handle 1.062 Id x 5.000 Black Soft Foam (1)
2 602241 Washer, Flat .281idx0.625odx.065t Stl Pld Ansi.250 (8)
3 601865 Nut, 250−20 .44hex .21h Stl Pld (8)
4 218327 Bracket, Mtg Axle (2)
5 601941 Screw, 250−20x1.75 Hexwhd.61d Gr5 Pld (4)
6 145665 Ring, Rtng Ext 1.000 Shaft x .052 Thk E Style Pld (2)
7 602251 Washer, Flat1.062idx2.000odx.134t Stl Pld Ansi 1.00 (2)
8 022825 Wheel, w/Tire&brg, 8 In Tire W/1 In Brg (2)
9 188397 Axle, Running Gear 1.000 Dia x 31.947 (1)
10 211341 Crutch Tip (1.062 I.d.) (2)
11 084499 Screw, 250−20x2.75 Hex Hd−pln Stl Pld Grd 5 (4)
12 602207 Washer, Lock .255idx0.489od x.062t Stl Pld Split.250 (8)
. Be sure to provide model and serial number when ordering replacement
parts.
. Remove paint
from axle grooves
before installing
retaining rings.
Part No.
5
4
10
11
12
3
2
1
12
2
3
6
7
8
9
For all Blue Star models and Renegade
models without cylinder rack.
Three base
mounting
holes.
For Renegade models with cylinder rack.
Item
. Blue Star Model Shown
/
