Hisense GV65160XXLCUS Owner's manual
- Category
- Dishwashers
- Type
- Owner's manual
This manual is also suitable for
AE
OPERATING
INSTRUCTIONS
DISHWASHER
GV65160XXLCUS
www.gorenje.com
Contents
2
Your dishwasher ........................................................................................
3
Important safety instructions .....................................................................
4
Before washing for the first time ...............................................................
5
Loading the dishwasher ............................................................................
7
Using the dishwasher ................................................................................
11
Settings .....................................................................................................
13
Care and maintenance instructions ..........................................................
15
Troubleshooting ........................................................................................
19
Installation instructions ..............................................................................
21
Service ......................................................................................................
24
Technical information ................................................................................
Your dishwasher
14
321 4 75 6
98 10 1311 12
1. Main power switch
2. Program selector
3. Auto wash
4. Intensive wash
5. Normal wash
6. Quick wash
7. Rinse
8. SpeedWash
9. Extra dry
10. Half load
11. Delayed start
12. Display
13. Rinse aid indicator
14. Salt indicator
2
Important safety instructions
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE
WARNING!
When using your dishwasher, follow basic precautions,
including the following:
•
Read all instructions before using the dishwasher.
•
Use the dishwasher only for its intended function.
•
Use only detergents or wetting agents recommended
for use in a dishwasher and keep them out of the
reach of children.
•
When loading items to be washed:
– locate sharp items so that they are not likely to
damage the door seal, and
– load sharp knives with the handles up to reduce the
risk of cut-type injuries.
•
Do not wash plastic items unless they are marked
“dishwasher safe” or the equivalent. For plastic items
not so marked, check the manufacturer’s recommen-
dations.
•
Do not operate the dishwasher unless all enclosure
panels are properly in place.
•
Do not tamper with controls.
•
Do not abuse, sit on, or stand on the door or dish rack
of the dishwasher.
•
To reduce the risk of injury, do not allow children to
play in or on a dishwasher.
•
Under certain conditions, hydrogen gas may be pro-
duced in a hot water system that has not been used
for two weeks or more. HYDROGEN GAS IS EXPLO-
SIVE. If the hot water system has not been used for
two weeks, before using the dishwasher turn on all
hot water faucets and let the water flow from each for
several minutes. This will release any accumulated
hydrogen gas. As the gas is flammable, do not smoke
or use an open flame during this time.
•
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding
it.
•
Read the grounding instructions in the installation in-
structions.
General
•
Do not run the dishwasher while you are out of the
home.
•
Do not store or use combustible materials, gasoline, or
other flammable vapors and liquids in the vicinity of this
or any other appliance.
•
Disconnect electrical power to dishwasher before servic-
ing.
•
Repairs should be done by a qualified technician.
WARNING!
This product may contain chemicals known to the state
of California to cause cancer or reproductive harm.
Installation
See the chapter Installation instructions.
Child safety
TIP!
Dishwasher detergents and rinse aids are corrosive, so
always keep them out of reach of children.
•
Should a child swallow dishwasher detergent or rinse
aid, give plenty to drink immediately, i.e., one or two
glasses of milk or water. Do not try to induce vomiting.
Seek medical advice immediately: Call the National
Capital Poison Center at 1-800-222-1222.
•
Always close the door and start the dishwasher as soon
as you put in the detergent.
•
Always keep small children away from the machine when
it is open. There may be some detergent residue left
inside the machine.
•
If dishwasher detergent gets in someone’s eyes, rinse
them with plenty of water for at least 15 minutes.
Winter storage/transport
Store the dishwasher above freezing and avoid long trans-
port distances in very cold weather. Transport the dishwash-
er upright or laying on its back.
Overflow guard function
The overflow protection starts pumping out the machine
and turns off the water supply if the water level in the dish-
washer exceeds the normal level. If the overflow protection
is triggered, turn off the water supply and call the Customer
Care Center.
Packing material
The packaging protects the product during transport. The
packaging material is recyclable. Separate the different
packaging materials to help reduce raw material use and
waste. Your dealer can take the packaging for recycling or
direct you to the nearest recycling center. The packaging
is comprised of:
•
Corrugated cardboard made from up to 100% recycled
material.
•
Expanded polystyrene (EPS) with no added chlorine or
fluorine.
•
Supports made from untreated wood.
•
Protective plastic made from polyethylene (PE).
3
Disposal
The dishwasher is manufactured and labeled for recycling.
When the machine has reached the end of its service life
and is to be disposed of, it should immediately be made
unusable. Pull out the power cable and cut it as short as
possible.
Contact your municipality for information about where and
how your dishwasher can be recycled correctly.
Before washing for the first time
Checking water hardness
In order to achieve good dishwashing results, the dishwash-
er needs soft water (water with low mineral content). Hard
water leaves a white coating on dishes and the dishwasher.
Water hardness is specified using the German water hard-
ness scale (°dH) or the French water hardness scale (°fH).
A water supply with a water hardness in excess of 6°dH
(9°fH) must be softened. This is done automatically with the
aid of the built-in water softener. In order for the water soft-
ener to function optimally, it must be adjusted to the hard-
ness of the water supply. Once you have adjusted the water
softener, use detergent and rinse aid doses suitable for soft
water.
Contact the local water utility to check the water hardness
in your area.
Make a note of the water hardness:____________
If the water hardness exceeds 50°dH (89°fH), we recom-
mend connecting an external water softener.
WARNING!
Hard water leaves a white coating on dishes and inside
the dishwasher. It is therefore important that you select
the right setting for the water softener! See Water hard-
ness.
Never run the dishwasher with an empty salt compartment
if the water supply has a water hardness in excess of 6°dH
(9°fH).
Set the Water hardness
Chapter Settings describes how to adjust the water softener.
Top up with salt
Salt compartment lid
1.
Unscrew the salt compartment lid.
2.
Insert the funnel supplied with the dishwasher in the salt
compartment top-up hole. First, pour in about 0.3 gal (1
l) of water.
3.
Then add salt, a maximum of 2 lb (1.0 kg), until the
compartment is full. Use large grain salt or special
dishwasher salt.
4.
Wipe up any excess salt so that the lid can be screwed
on firmly.
4
In order to avoid rust stains, a dishwashing program must
be started immediately after adding salt.
Set the Rinse aid
The chapter Settings describes how to set the rinse aid
dosage.
Top up with rinse aid
Use rinse aid to improve wash and dry times. Also use rinse
aid to achieve clear and spotless results.
Press to open
1.
Open the rinse aid compartment lid.
2.
Carefully top up with rinse aid to the level marked max.
3.
Wipe up any spilled rinse aid around the compartment.
4.
Close the lid firmly.
Loading the dishwasher
Greener dishwashing
•
Do not rinse under running water. Simply scrape off
large food particles before loading the dishwasher.
•
Choose an environmentally-friendly detergent. Read the
environmental declaration on the packaging!
•
Do not start the dishwasher until it is fully loaded to save
energy.
•
If the dishes are only lightly soiled, you can select a
program with a low temperature.
•
Better drying results are achieved if you open the door
a little once the program has ended. (If the dishwasher
is built-in, the surrounding furnishings must be resistant
to any condensation.)
Fragile dishes
Some cookware is not dishwasher safe. This can be for
several reasons. Some materials cannot withstand high
temperatures, others can be damaged by dishwasher deter-
gent.
Use caution with, for example, handmade items, fragile
decoration, crystal/glassware, silver, copper, tin, aluminum,
wood, and plastic. Look for the "Dishwasher safe" marking.
Points to consider
•
All dirty surfaces should face in and down!
•
Dishes should not be placed in or on each other.
•
Angle dishes with hollows, such as cups, so that the
rinse water will run off. This is also important for plastic
items.
•
Place the upper basket in its highest position when
dishwashing very large plates.
•
Make sure small items cannot fall through the dishwash-
er basket; place them in the cutlery basket.
NOTE!
Check that the spray arms can rotate freely.
The baskets
The dishwasher includes an upper, a lower, and a cutlery
basket.
Upper basket
Place glasses, cups, bowls, side plates, and saucers in the
upper basket. Place all soiled surfaces face down! Place
5
wine glasses on the wine glass shelf. Place knives in the
knife stand on the right (if space allows).
Raising and lowering the upper basket
1.
Pull out the upper basket.
2.
Grab the sides of the upper basket with both hands and
lift it up.
3.
Repeatedly lift the basket with both hands to change its
position. (The upper basket can be set in three posi-
tions.) When the upper basket is in the highest position,
lifting it will return it to the lowest position. Note that both
sides of the basket must always be set to the same
height.
Lower basket
Place plates, side plates, serving dishes, pots, and cutlery
(in the cutlery basket) in the lower basket.
Cutlery basket
Place cutlery with the handles facing down, except for
knives, and spread them out as much as possible. Ensure
that spoons do not stack inside each other.
Place the cutlery basket in the lower basket.
Typical load for 10 place settings
Upper basket with 10 place settings AHAM DW-1
NOTE!
Ensure that the upper basket is set to its highest position.
6
Lower basket with 10 place settings AHAM DW-1
Using the dishwasher
Add detergent
Press to open
1.
Prewash detergent compartment
2.
Main wash detergent compartment
Detergent is added according to water hardness.
Follow the instructions on the detergent packaging. This
dishwasher is fitted with a water softener, so use detergent
and rinse aid doses suitable for soft water.
Too much detergent can result in less effective dishwashing
and also entails greater environmental impact.
The detergent compartment must be dry when adding de-
tergent. There is one compartment for the prewash and one
for the main wash. If powder or liquid dishwasher detergent
is used, add a small amount of the detergent to the prewash
compartment. Contact the detergent manufacturer if you
have questions about the detergent.
NOTE!
Use only dishwasher detergent! Liquid hand-washing
detergent must not be used as the foam that forms pre-
vents the dishwasher from operating effectively.
Dishwasher tablets
Halve the tablet if it is difficult to close the dispenser lid.
There is a risk that the detergent will not be released prop-
erly if the lid is tight and cannot open correctly.
NOTE!
Dishwasher tablets are not recommended for short pro-
grams (less than 75 minutes). Use powder or liquid dish-
washer detergent instead.
All-in-one detergent
There are many types of all-in-one detergents on the market.
Read through the directions for these products carefully.
Chapter Settings describes how to activate TAB (3-in-1/all-
in-one detergent). The salt compartment must be filled with
salt. If you are not satisfied with the washing or drying re-
sults, deactivate the setting TAB (3-in-1/all-in-one detergent)
and fill salt, detergent, and rinse aid. See Chapter Before
washing for the first time.
7
NOTE!
Optimal washing and drying results are achieved by using
normal dishwasher detergent together with separately
dispensed rinse aid and salt.
The main power switch
Press and hold the main power switch until the display turns
on. Also check that the water supply valve is on.
PROGRAMS - Select a program
Select a program to suit the type of dishes and how dirty
they are.
Press the Program selector one or more times until the de-
sired program symbol is activated.
Auto wash
The dishwasher can measure how dirty the dishes are and
adjust water consumption and temperature accordingly.
When newly installed, the program needs to be run five
times before it is fully adapted and can provide the best re-
sults.
Intensive wash
Program for heavily soiled dishes, such as pans, casserole
dishes, and oven dishes. If these dishes do not completely
fill the dishwasher, you can add plates and other dishes that
can withstand a Heavy wash to fill out the load.
Normal wash
This program is recommended for daily, regular, or typical
use to completely wash a full load of normally soiled dishes,
such as plates, serving dishes, cups, and glasses.
Quick wash
This program is used for glasses and porcelain that is
lightly soiled, such as coffee cups.
In combination with SpeedWash, a shorter program is
achieved (15 minutes).
Rinse
Use to rinse dishes while you wait for the dishwasher to
become fully loaded.
EXTRA - Selecting Options
To select an option, press one of the option buttons until
the option is activated. The available options vary between
programs and some options cannot be combined (available
options glow dimly).
SpeedWash
This option shortens the program time, but uses more ener-
gy and water.
Extra dry
If you activate this option, a higher temperature in the final
rinse improves the drying results. Energy consumption in-
creases slightly.
Half load
This option adapts the dishwashing program to a half-filled
dishwasher, using less energy and water.
Delayed start
When you select Delayed start, the dishwasher will start 1-
24 hours after you close the door.
1.
Press the button once to activate Delayed start. Press
the button several times – or hold it in – to set the de-
sired number of hours.
2.
Close the door and the dishwasher display counts down
1 hour at a time and starts after the selected delay.
If you want to cancel the Delayed start option, open the door
and press and hold the main power switch until the display
turns off.
Starting the dishwasher
Press and hold the Program selector until it starts to flash.
Close the door within four seconds to start the dishwasher.
TIME - Time remaining
Once you have chosen a program and options, the time the
program took when last used is displayed.
Stopping or changing a program
If you want to change the program after starting the dish-
washer, open the door then press and hold the main power
switch until the display turns off. Add more detergent if the
lid of the detergent dispenser has opened. Then press the
main power switch again to choose a new program.
WARNING!
The dishwasher door must not be open while a program
is in progress. If the door is open, "STR" is shown on the
display. If you want the dishwashing program to continue,
press the Program selector and close the door immediate-
ly. If you want to cancel the dishwashing program, press
and hold the main power switch until the display turns off.
8
If the dishwasher is turned off due to a
power failure
If the program was not finished, the interrupted program
resumes when power is restored.
NOTE!
During drying, the program is interrupted if the power is
cut or the door is open for more than 2 minutes.
Once the program has finished
The dishwasher switches off automatically after the program
ends.
To minimize the risk of leaks, we recommend that you turn
off the water supply valve if away from home for an extended
period of time.
How to get the best drying results
•
Fully load the dishwasher.
•
Angle dishes with hollows, such as cups, so that the
rinse water will run off. This is also important for plastic
items.
•
Top up with rinse aid or increase the rinse aid dosage
level.
•
Activate the Extra dry option.
•
Open the door a little once the program has finished.
•
Allow the dishes to cool before unloading the dishwash-
er.
Unloading the dishwasher
Hot porcelain is more fragile. Leave the dishes to cool in
the dishwasher before unloading them.
Unload the lower basket first to avoid any water drops from
the upper basket falling onto the dishes in the lower basket.
9
Program chart
Consumption values
1)
Final rinseNumber of
rinses
Main washPrewashesEXTRA
- Options
Detergent,
compartment
1 / 2
(ml)
PROGRAMS
- Program
Water cons.
(L)
Energy
(approx. kWh)
Dishwashing
time
(approx.
hrs:min)
14-201.01-1.062:40-3:15
65 °C
150 °F2-3
50-65 °C
120-150 °F2-3--- / 25Auto wash
171.73:40
65 °C
150 °F2
70 °C
160 °F210 / 25Intensive wash
13.00.872:20
50 °C
120 °F2
50 °C
120 °F3--- / 25
Normal wash
2)
100.20:20
25 °C
80 °F1
35 °C
95 °F--- / 10Quick wash
30.010:07
--- °C
--- °F1--- / ---Rinse
1)
Consumption values vary depending on the temperature of the incoming water, room temperature, load size, selected additional functions, and more.
2)
The energy label performance figures are based on this program. This program is recommended for daily, regular, or typical use to completely wash a full load of
normally soiled dishes, such as plates, serving dishes, cups and glasses.
10
Settings
Open the settings menu:
First, open the door. Turn off the machine. Press and hold the main power switch until the display
lights up.
1.
Within 10 seconds:
- press the Program selector and the option button for SpeedWash.
2.
+
The display shows the settings menu (current setting and its currently set value).3.
(Exit the menu by browsing through the menu or pressing the main power switch.)
Navigate the settings menu:
Press to save the setting value and continue to
the next setting.
Current setting.
Current setting value.
Press to browse between setting values.
You can now adjust the following settings:
OptionsSettings
Rinse aid dosage setting.1:00 - 1:05Rinse aid1.
Increase the rinse aid dosage:
• If the dishes have water marks.
Reduce the rinse aid dosage:
• If the dishes have a sticky white/blue film.
• If the dishes are streaked.
• Heavy foaming. If you have very soft water, the rinse
aid can be diluted 50:50 with water.
Pre-selected at factory: 05
11
OptionsSettings
Adjusting the water softener. Select a setting depending
on the hardness of the water supply. It is important that
this setting is correct!
2:00 - 2:09Water hardness2.
Recommended
setting
French water
hardness scale
German water
hardness scale
2:000-9°fH0-5°dH
2:0110-14°fH6-8°dH
2:0215-20°fH9-11°dH
2:0321-25°fH12-14°dH
2:0426-34°fH15-19°dH
2:0535-43°fH22-24°dH
2:0644-52°fH25-29°dH
2:0753-70°fH30-39°dH
2:0871-88°fH40-49°dH
2:0989°fH50°dH
Do not forget to put salt in the salt compartment after
you have set the water softener to 2:01 - 2:09.
For a water supply with a hardness under 6°dH (9°fH),
select 2:00. The water softener is deactivated and no
salt is needed.
Pre-selected at factory: 04
You can activate this setting when using 3-in-1/all-in-
one detergent. The dishwashing programs automatically
adapt to provide the best possible dishwashing and
drying results every time. If this setting is activated,
there is no need to add rinse aid since this option dis-
ables rinse aid dispensing. It also reduces the amount
of salt added to the water softener. Note that salt must
be put in the salt compartment.
3:00 (Off)
3:01 (On)
TAB
(3-in-1/all-in-one detergent)
3.
NOTE!
In order to achieve good dishwashing results, it is
essential to check which type of detergent or all-in-
one product best suits your needs! Read the deter-
gent packaging carefully for information on proper
use. Always follow the directions for use or informa-
tion on the detergent packaging!
12
Care and maintenance instructions
Top up with rinse aid
When the rinse aid needs topping up, the above symbol
lights on the display.
Press to open
1.
Open the rinse aid compartment lid.
2.
Carefully top up with rinse aid to the level marked max.
3.
Wipe up any spilled rinse aid around the compartment.
4.
Close the lid firmly.
After topping up, it may take a while before the symbol goes
out.
Top up with salt
When the salt needs topping up, the above symbol lights
on the display.
Salt compartment lid
When the salt runs out, unscrew the cap and fill the contain-
er with salt. Water is only needed the first time! Wipe clean
and tighten. Run a program to ensure that any salt in the
dishwasher is rinsed away.
After topping up, it may take a while before the symbol goes
out.
WARNING!
In order to avoid rust stains, a dishwashing program must
be started immediately after adding salt.
Never pour dishwasher detergent into the salt compart-
ment. This destroys the water softener!
Coarse filter
The coarse filter traps larger food particles, which cannot
get past the drain pump. Empty the coarse filter when nec-
essary.
Coarse filter
1.
Lift the coarse filter by the handle.
2.
Empty the coarse filter. Remember to reinstall it!
Fine filter
Debris that collects on the fine filter is automatically rinsed
away during each wash. Clean the fine filter when neces-
sary.
Fine filter
1.
Turn the handle counterclockwise.
2.
Lift the filter straight up using the handle. Remove the
coarse filter to clean the fine filter.
3.
Reinstall in reverse order. Check that the edges seal
properly when reinstalling the fine filter.
4.
Lock the filter in place by turning the handle clockwise
to the stop position. The handle should point straight
out from the dishwasher.
NOTE!
Dishwashing results may be
affected if the filters are incorrectly
fitted. Note that the dishwasher
must not be used without the filters
in place!
13
NOTE!
Check that the colored stop on the
right in the bottom drain is in
place.
Spray arms
Holes and bearings can become blocked. Remove debris
using a needle or similar item. The spray arms have holes
on the bottom.
Spray arms can be removed for cleaning. Remember to fit
them firmly back into place afterward.
Lower spray arm
•
Pull the lower spray arm straight up to release it.
Upper spray arm
1.
Pull out the upper basket.
2.
Unscrew the spray arm bearings counterclockwise to
remove the spray arm from the upper basket.
The door and the door seal
Regularly clean the sides of the door and the door seal. Use
a slightly damp cloth (with a little cleaner if necessary).
Display panel
Keep the buttons clean and free from grease. Wipe them
clean with a dry or slightly damp cloth. Never use cleaners
– they can scratch the surface. Use the main power switch
to turn off the dishwasher before cleaning the buttons to
avoid activating any buttons unintentionally.
The dishwasher tub
The dishwasher tub is made of stainless steel and is kept
clean through normal use.
Limescale deposits
If you have hard water, limescale deposits may build up in
the dishwasher. If this happens, run the Intensive wash
program with two tablespoons of citric acid in the detergent
compartment (with no dishes in the machine).
TIP!
Use citric acid or commercially available dishwasher
cleaner.
Unblocking the drain pump
If the dishwasher still contains water after the program has
finished, something may be blocking the drain pump. Such
items are easily removed.
1.
Turn off the machine using the main power switch and
unplug it from the power outlet.
2.
Remove the coarse filter and the fine filter.
3.
Scoop out the water from the dishwasher tub.
4.
In order to inspect the drain pump, remove the colored
stop on the right in the bottom drain.
5.
Turn the pump wheel located behind the drain pump
stop by hand. Carefully remove any items.
6.
Reinstall the drain pump stop along with the fine and
coarse filters.
7.
Plug the machine in again.
If the dishwasher still does not start and a whirring sound
is heard, the overflow protection has been triggered.
•
Shut off the water.
•
Unplug the unit from the power outlet.
•
Call the Customer Care Center.
Drain pump stop
NOTE!
Do not forget to reinstall the drain pump stop.
14
Troubleshooting
ActionType of fault on the display
Clear the drain pump. See the chapter Care and maintenance instructions. If the
problem persists, call the Customer Care Center.
OverfillingF10
See “Water remains in the dishwasher above the filters” in the table “Problem”
below. If the problem persists, call the Customer Care Center.
Water outlet faultF11
Check that the water supply valve is on. If the problem persists, call the Customer
Care Center.
Water inlet faultF12
Turn off the water supply valve and call the Customer Care Center.Inlet valve leakageF40
Clean the coarse and fine filters. If the problem persists, call the Customer Care
Center.
Water level faultF52
Turn off the water supply valve and call the Customer Care Center.OverfillingF54
Call the Customer Care Center.Circulation faultF56
Press any button to clear the error message.
ActionPossible causesProblem
Wait a moment then try again.You have pressed the buttons too soon
after opening the door.
The buttons do not react when pressed.
Clean with a dry or slightly damp cloth.The buttons are dirty.
Open the door. The buttons only react
to use when the door is open.
The door is closed.
Check that the baskets are correctly po-
sitioned horizontally.
The baskets are not correctly positioned.Cannot close door.
Check that the dishes are not blocking
the baskets from sliding properly into
place.
Close the door within four seconds, oth-
erwise the dishwasher will not start. See
Starting the dishwasher in the chapter
Using the dishwasher.
The door is not closed properly or was
not closed immediately after starting the
program.
The dishwasher does not start.
Check.A fuse/circuit breaker has been tripped.
Check.The plug is not plugged into the power
outlet.
Check.The water supply valve is turned off.
Check.Overflow/leaks.
Turn off the water supply valve. Pull out
the plug and call the Customer Care
Center.
A whirring sound (the drain pump) is
heard from the dishwasher and does not
stop when the main power switch is
turned off.
Press and hold the main power switch
until the display turns off if you want to
cancel the Delayed start option. Restart
the dishwasher.
Check that the Delayed start option has
not been selected.
15
ActionPossible causesProblem
Remove the arms and clean them.The spray arms do not rotate.The dishes are not clean.
Check that the dishes are not blocking
the spray arms.
Clean the spray arms. See the chapter
Care and maintenance instructions.
Spray arm holes or bearings blocked.
Choose a longer program.Unsuitable dishwashing program.
Dose according to water hardness. Far
too much or far too little detergent can
result in poor dishwashing results.
Incorrect detergent dosage.
Avoid large packages.Detergent is too old. Detergent is a per-
ishable product.
Do not cover dishes with large bowls or
lids. Avoid placing very tall glasses in
the corners of the baskets.
Dishes loaded incorrectly.
Load the dishes securely.Glasses and cups have toppled over
during the program.
Check that the filter handle is locked in
the stop position. The handle should
point straight out from the dishwasher.
The filters are not fitted correctly.
Check that the colored stop on the right
in the bottom drain is in place. See the
chapter Care and maintenance instruc-
tions.
Drain pump stop missing.
Rinse off these types of food if not start-
ing the dishwasher immediately. Use the
Rinse program.
Some types of food, such as mustard,
mayonnaise, lemon, vinegar, salt, and
dressings, can mark stainless steel if left
for too long.
Spots on stainless steel or silver.
In order to avoid marks and tarnishing,
separate dishes made from different
metals, such as silver, stainless steel,
and aluminum.
All stainless steel can cause spots on
silver if they come into contact during
dishwashing. Aluminum can also cause
spots on dishes.
Check that the salt compartment lid is
properly tightened. Otherwise call the
Customer Care Center.
The water softener is leaking salt.Spots or films on the dishes.
See the chapter Settings.Incorrect water softener setting.
See the chapter Settings.Incorrect rinse aid dosage setting.
Top up with salt. See the chapter Before
washing for the first time.
Salt compartment empty.
Inactivate the setting TAB (3-in-1/all-in-
one detergent) and top up with salt and
rinse aid.
3-in-1/all-in-one detergent is used and
the setting TAB (3-in-1/all-in-one deter-
gent) is activated.
Wash crystal at a low temperature and
with a conservative amount of detergent.
Contact the detergent manufacturer.
Too high temperature and/or too much
detergent can cause etching on crystal.
Unfortunately, this cannot be repaired,
only prevented.
16
ActionPossible causesProblem
Reduce the amount. See the sections
Before washing for the first time and
Settings. If you have very soft water, you
may want to dilute the rinse aid 50:50
with water.
Rinse aid dosage setting too high.The dishes have a sticky white/blue film.
Use a detergent with a bleaching agent.Lipstick and tea can be difficult to wash
off.
Spots left after washing.
The detergent compartment must be dry
when adding detergent.
The detergent compartment was damp
when adding detergent.
Detergent residue in the detergent com-
partment after dishwashing.
Check that the dishes are placed secure-
ly. Spin the spray arms to make sure
they can rotate.
The dishes are not correctly placed or
the spray arms are not rotating.
Rattling sound when dishwashing.
If you want the dishwashing program to
continue, press the Program selector
and close the door within five seconds.
The dishwasher door has been opened
while a program is in progress.
"STR" is shown on the display.
If you want to cancel the dishwashing
program, press and hold the main power
switch until the display turns off.
Clean the coarse and fine filters.The filters are blocked.Water remains in the dishwasher above
the filters.
Check that the filter handle is locked in
the stop position. The handle should
point straight out from the dishwasher.
The filters are not fitted correctly.
Clean the drain pump. See the chapter
Care and maintenance instructions.
Debris in the drain pump.
Check that the colored stop on the right
in the bottom drain is in place. See the
chapter Care and maintenance instruc-
tions.
Drain pump stop missing.
Check that the hose is free from kinks
and sharp bends.
Kink in drain hose.
Loosen the drain hose from where it
terminates. Check that no debris has
clogged the hose. Is the cone-shaped
part of the drain boot cut to the maxi-
mum size of the fitting where it attaches?
Blocked drain hose.
Clean with dish brush and low foaming
cleaner.
Dirt around the seals and in corners.Bad odor in dishwasher.
Run a program with a higher tempera-
ture about once a month.
Low temperature programs have been
selected for a prolonged period.
17
ActionPossible causesProblem
Activate the Extra dry option.Depending on the load, the program's
drying cycle may be insufficient.
The dishes are not dry enough.
Fully load the dishwasher.The dishwasher is not fully loaded.
Top up with rinse add or increase the
rinse aid dosage. See the sections Be-
fore washing for the first time and Set-
tings.
Rinse aid needs topping up or dosage
is set too low.
Inactivate the setting TAB (3-in-1/all-in-
one detergent) and top up with salt and
rinse aid.
3-in-1/all-in-one detergent is used and
the setting TAB (3-in-1/all-in-one deter-
gent) is activated.
Open the door a little once the program
has finished.
18
Installation instructions
33.74-36.61 (857- 930)
20.47 (520)
21.89 (556)
27.56-31.50* (700-800*)
2.14 (54)
7.70 (196)
17.50 (444)
22.56 (573)
23.79 (604)
4.92-7.80 (125-198)
2.16 (55)
1.20 (31)
4.21 (107)
48.58 (1234)
29.13 (740)
27.95 (710)
Door length
*
Nominal dimensions. Actual measurements may vary.
'' (mm)
It is important that you read through and follow the instruc-
tions and directions below. Conduct installation and connec-
tion in accordance with the separate installation instructions.
Important safety instructions
•
Connections to electricity, water, and drainage must be
performed by a qualified professional.
•
Always follow applicable regulations for water, drainage,
and electricity.
•
Take care during installation! Wear protective gloves!
There must always be two people!
•
Place a drip tray on the floor beneath the dishwasher to
prevent damage from any water leaks.
•
Before screwing the dishwasher into place, test the
dishwasher by running the Rinse program. Check that
the dishwasher fills with water and drains. Also check
that none of the connections leak.
WARNING!
Turn off the water supply when installing the dishwasher!
The plug must be disconnected or power to the outlet
turned off while installing the dishwasher!
Setup
•
The recess and connection dimensions are included in
the separate installation instructions. Check that all di-
mensions are correct before starting the installation.
Note that the height of the integrated door panel can be
adjusted to match other fittings.
•
33.86-36.73
(860-933)
24 (610)
24 (610)
4.95 (125)
1.5 (38)
3.7 (94)
'' (mm)
The electrical and water
supplies should enter
through the area
indicated by the shading
on the illustration.
•
Make sure the area on which the dishwasher is to be
installed is firm. Adjust the adjustable feet so that the
dishwasher is level.
NOTE!
Framed cabinets require additional finished filler material
behind the face frame for a proper installation. A minimum
3½” (89 mm) finished return is required on all sides of the
opening.
3½”
¾”
3½”
Frameless
cabinetry
Filler
Framed
cabinetry
19
Drain connection
See the separate installation instructions for necessary in-
formation.
This dishwasher is suitable for installing in a raised recess
(to attain an ergonomic working height). This means that
the dishwasher can be placed so that the drain hose runs
to a lower level than the bottom of the dishwasher, such as
by routing it directly to a floor drain. The dishwasher is fitted
with an integrated anti-siphon device to prevent the machine
from being emptied of water during the wash cycle.
The drain hose can also be connected to a connection nipple
on the sink unit's water trap. The connection nipple must
have an internal diameter of at least 0.6" (14 mm).
The drain hose may be extended by a maximum of 118" (3
m) (the total length of the drain hose must not exceed 177"
(4.5 m)). Any joins and connecting pipes must have an in-
ternal diameter of at least 0.6" (14 mm). However, the drain
hose should ideally be replaced with a new hose without
joins.
No part of the drain hose may be more than 37.4" (950 mm)
above the bottom of the dishwasher.
Attach the drain hose with a hose clamp. Ensure that the
drain hose has no kinks.
Connection to water supply
Use only the inlet hose supplied with the dishwasher. Do
not re-use old or other spare hoses.
The supply pipe must be fitted with a water supply valve.
The water supply valve must be easily accessible, so that
the water can be shut off if the dishwasher has to be moved.
Once the installation is complete, turn on the water supply
valve and allow the pressure to settle for a while. Check
that all connections are watertight.
Water supply
The machine can be connected to either a cold or a hot
(max. 160 °F (70 °C)) water supply. The water pressure
should be 4.2-140 psi.
Connection to cold water supply
Connect the dishwasher to the cold water supply if the
building is heated using oil, electricity, or gas.
Connection to hot water supply
Connect the dishwasher to the hot water supply (max.
160 °F (70 °C)) if the building is heated using an energy-
efficient means such as district heating, solar power, or
geothermal power. Choosing a hot water connection cuts
dishwashing times and reduces the dishwasher's energy
consumption.
NOTE!
Do not exceed the permitted water supply temperature.
Certain materials used in some cookware cannot with-
stand strong heat. See Fragile dishes in the chapter
Loading the dishwasher.
Electrical connection
Information about the electrical connection can be found on
the serial number plate. This specification must match the
electricity supply.
The power supply receptacle for the appliance must be in-
stalled in a cabinet or on a wall adjacent to the undercounter
space in which the appliance is to be installed. Do not use
an extension cord for this appliance.
Use caution when the appliance is installed or removed to
reduce the likelihood of damage to the power supply cord.
Grounding Instructions
This appliance must be grounded. In the event of a malfunc-
tion or breakdown, grounding will reduce the risk of electric
shock by providing a path of least resistance for electric
current. This appliance is equipped with a cord fitted with
an equipment grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is
installed and grounded in accordance with all local codes
and ordinances.
WARNING!
Improper connection of the equipment grounding conduc-
tor can result in a risk of electric shock. Check with a
qualified electrician or service representative if you are in
doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance. If it
does not fit the outlet, have an appropriate outlet installed
by a qualified electrician.
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Hisense GV65160XXLCUS Owner's manual
- Category
- Dishwashers
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI