Sharp SX76NF100 User manual

MODEL

Please read this operation manual

carefully before using the colour

television.

OPERATION MANUAL

COLOUR TELEVISION

MODEL

SX66NF100

SX76NF100

(SX66NF100)

(SX76NF100)

03.7.30, 8:55 AMPage 1

2

Safety precautions

Do not place this TV set on an unstable

cart, stand, shelf, or table. The TV set

may fall, causing serious injury to a child

or adult, and serious damage to the set.

Sharp recommends securing the TV set

to a stable surface or wall to prevent the

set from falling due to sudden shocks or

impact.

Do not place a flower vase or anything

else containing liquid on the TV set, as

liquid spilt on the TV set can cause

electrical shock or failure.

Damage

Turn off the power and unplug the power

cord from the wall outlet immediately if

the TV set begins to make any unusual

noises or gives off smoke or an unusual

smell. Then call your dealer for service.

Servicing

To reduce the risk of electric shock, do

not remove the back of the cabinet. This

TV set contains dangerous voltage.

Unstable surface

and shocks

Liquid entry

Never insert or drop any metallic or

inflammable objects into the ventilation

openings of the TV set, as this can cause

fire, electrical shock, or electrical failure.

Object entry

Water

To prevent fire or electrical shock, do not

place the TV set near a bathroom,

swimming pool or other area where it may

become wet.

03.7.30, 8:57 AMPage 2

3

Power cord

protection

To prevent electrical shock, do not subject

the AC power cord to damage by bending

or twisting it, or by placing heavy items on

top of it and do not place the AC power

cord under the TV set. If the AC power

cord becomes damaged, unplug it from

the wall outlet immediately and call your

dealer for service.

To prevent electrical shock, do not use the

TV set in an excessively damp place.

Moisture

Ventilation

Do not place this TV set in a confined

area, such as on a bookshelf or in a built-

in case. Leave adequate space behind the

TV for proper ventilation.

TV set position

Do place the TV set onto an even stand,

table or track which size is bigger than the

TV set.

If the TV set is put onto a smaller size or

uneven stand, table or track may cause

the TV cabinet distort.

Do not put or insert anything between TV

set and the stand, table or track.

Fire prevention

To prevent fire, never place any type of

candle or naked flames on the top or near

the TV set.

TV set and cart

combination

Television equipment and cart

combination should be moved with care.

Quick stops, excessive force, and uneven

surfaces may cause the equipment and

cart combination to overturn.

03.7.30, 8:57 AMPage 3

4

Selecting menu items

Useful features

Contents

Safety precautions ....................................................2

Accessories .............................................................. 5

Easy setup ............................................................... 6

Part names ............................................................... 7

Installing batteries in the remote control unit ........ 7

Antenna connections.............................................. 11

Watching a TV programme......................................12

Operating the TV buttons ........................................13

Channel/Timer display ............................................14

Mute ........................................................................14

AV mode selection ..................................................14

Channel recall .........................................................15

TV/Video selection ..................................................15

Selecting a menu item.............................................16

On-screen display language selection .................... 17

Manual channel tuning ............................................18

Auto channel tuning ................................................19

Channel setting .......................................................20

Picture adjustment ..................................................21

Sound adjustment .................................................. 22

Surround sound.......................................................23

Favourite channels ..................................................23

Wide mode ..............................................................24

Blue screen ............................................................ 26

Auto select ..............................................................27

Save ........................................................................28

Headphones volume .............................................. 29

Rotation ...................................................................29

Off timer ..................................................................30

On timer ..................................................................31

Reminder on-screen timer.......................................32

NICAM broadcasts ..................................................33

A2 stereo system broadcasts ..................................34

Teletext broadcasts .................................................35

Connecting to a DVD player ....................................40

Watching DVD playback ......................................... 40

Connecting to video equipment...............................41

Troubleshooting .......................................................42

Specifications ..........................................................43

Preparation

Watching TV

Settings and adjustments

Broadcast features

Connections

Troubleshooting

Specifications

03.7.30, 8:57 AMPage 4

5

Dear SHARP Customer

Thank you for buying SHARP’s Colour

Television. We hope you will have many

years of enjoyment from this television

set. To ensure proper operation, please

read this manual carefully, and keep it in

a safe place for future reference.

Remote control

Size-AA batteries

Operation manual

The following accessories are included with this television.

Accessories

03.7.30, 8:57 AMPage 5

6

Easy setup

To use your TV set, perform the easy setup procedure below.

The mark indicates the page number with more detailed information.

Connect the antenna.

• See

11

to connect the antenna.

Connect any video equipment.

• See

40

,

41

to connect video equipment.

• See the operation manual of your video equipment when

connecting it to the TV set.

Insert the batteries into the remote control.

• Use the two batteries included with the TV.

• See

7

.

Insert the AC plug to the power outlet.

• If you will not use the TV set for a considerable length of

time, as a safety precaution, unplug the cord from the outlet.

Tune the channels.

• Use the buttons on the TV.

• See

18

,

19

.

1

2

3

4

5

03.7.30, 8:57 AMPage 6

7

Part names

• Be sure to match the battery

jj

j/

kk

k terminals with the

jj

j/

kk

k marks inside the compartment.

• Remove the batteries if weak or if the unit is not in use for long periods.

• Do not mix old and new batteries.

• Incorrect installation of the batteries may damage the remote control.

With your thumbnail, pull

up at the slit to open the

battery cover.

Insert two batteries

(size AA).

Replace the battery cover.

Installing batteries in the remote control unit

Remote control

The mark indicates the page number with more detailed information.

1 2 3

Turns the TV on or

set it to Standby mode.

Infrared transmitter window

Aim this window at the infrared

sensor window on your TV set.

Mutes the sound and restores

sound to previous level.

Produces a more spacious sound.

Adjust the volume.

Used for MENU setup.

Resets all settings.

Teletext buttons

Operate the Teletext functions.

Operate the Favourite Channel

and Teletext functions.

Switches between main and sub

sound, and stereo and monaural

sound.

Colour buttons /

Displays the channel and timer

settings on the screen.

Number buttons

Select the channels and input

numbers.

Switches between one- or two-digit

mode channel selection.

Returns to previously viewed

channel.

Select the channels.

Used for MENU setup.

Calls the MENU screen.

Switches between TV broadcasts

and AV input programmes.

Switches Power Save mode

on or off.

12

14

33

23

3523

12

21

35-39

28

15

14

12

15

12

16

TV/VIDEO

MENU

CH

SURROUND

MPX

NORMAL

/

14

Changes Picture and Sound setting.

STANDARD, MOVIE,

MUSIC, NEWS

AV MODE

POWER SAVE

Selects the width of picture.

24

03.7.30, 8:57 AMPage 7

8

Part names

Bottom

12

7

31

28

SX66NF100

13

41

18

13

CH

/

Power indicator

Power can be turned on by the remote

control when the indicator is lit red.

Door

Power switch

Turns on and off

the main power.

Infrared sensor window

Receives the infrared wave

from the remote control.

Headphones jack

Used to listen to the audio with headphones.

(When using headphones, see .)

AV-3 IN terminals

Connect to a camcorder, video game,

VCR, DVD player, etc.

ON TIMER indicator

Lights up red when the On Timer is set.

POWER SAVE indicator

Lights up red when Power

Save mode is on.

Channel Up/Down buttons

Select the channels.

Tune or set the channels.

MENU/PRESET

/

MENU/PRESET button

Used for MENU setup.

Tunes the channels.

Volume Up/Down buttons

Adjust the volume.

Used for Preset.

TV Set

To open the door

Using the projection located under

the "PULL-OPEN" indication, pull

and lift the door open.

To close the door

Using the projection, lower the door

until closed.

Caution:

• When opening or closing the door, do

not insert your fingers into the gap

between the door and front panel.

This may result in an injury.

• Minimal electric power remains consumed even after the main power is turned off with on the

TV set.

03.7.30, 8:59 AMPage 8

9

Top

SX76NF100

Bottom

12

7

31

28

13

41

18

13 13

AV-3 IN terminals

Connect to a camcorder, video game,

VCR, DVD player, etc.

MENU/PRESET

CH

/

Volume Up/Down buttons

Adjust the volume.

Used for Preset.

Channel Up/Down buttons

Select the channels.

Tune or set the channels.

MENU/PRESET button

Used for MENU setup.

Tunes the channels.

Power switch

Turns on and off

the main power.

Infrared sensor window

Receives the infrared wave from the remote control.

13

Headphones jack

Used to listen to the audio with headphones.

(When using headphones, see .)

Power indicator

Power can be turned on by the remote

control when the indicator is lit red.

ON TIMER indicator

Lights up red when the On Timer is set.

POWER SAVE indicator

Lights up red when Power

Save mode is on.

Door

To open the door

Using the projection located under

the "PULL-OPEN" indication, pull

and lift the door open.

To close the door

Using the projection, lower the door

until closed.

Caution:

• When opening or closing the door, do

not insert your fingers into the gap

between the door and front panel.

This may result in an injury.

• Minimal electric power remains consumed even after the main power is turned off with on the

TV set.

03.7.30, 8:59 AMPage 9

10

Part names

Rear terminals

SX66NF100 SX76NF100

11

41

40

41

COMPONENT IN/AUDIO IN

terminals

Connect to a DVD player, etc.

AV-2 IN VIDEO/AUDIO (L/R)

terminals

Connect to a VCR, etc.

AV-1 IN VIDEO/AUDIO (L/R)

terminals

Connect to a VCR, etc.

VIDEO/AUDIO (L/R) OUT terminals

Connect to a VCR, etc.

S-VIDEO (AV-1 IN) terminal

Connects to a VCR, etc.

Antenna In terminal

Connects to an antenna.

03.7.30, 8:59 AMPage 10

11

If your outdoor antenna uses a 75-ohm coaxial cable with a standard

DIN45325 plug (IEC 169-2), plug it into the Antenna In terminal at the

rear of the TV set.

If your outdoor antenna uses a 300-ohm twin-lead flat feeder, connect a

300-ohm to 75-ohm impedance converter and plug it into the Antenna In

terminal at the rear of the TV set.

Connecting to an antenna via a VCR

You can also connect the TV set to the tuner on a VCR using the connection shown below.

• Remove the power cord from the power outlet before connecting the antenna to the TV set.

• When using the RF terminal connection, set the TV to channel zero to make initial adjustments for the VCR.

• Turn off the power on the TV set and the VCR being connected before making the above connections.

• Be sure the cord plugs are fully inserted in the connection terminals.

• See the operation manual of your VCR for connection details.

Connecting to an antenna

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of

the types of connections that are used for coaxial and feeder cables.

Antenna connections

Standard DIN45325 plug (IEC169-2)

75-ohm coaxial cable (round cable) (not supplied)

300-ohm twin-lead

flat feeder

(not supplied)

75-ohm impedance

converter

(not supplied)

TV

Antenna In terminal

VCR

TV

Antenna In

terminal

To antenna in

terminal

To RF out

terminal

03.7.30, 8:59 AMPage 11

12

Watching TV

1 Turn on power.

• When the Power indicator (see

8

and

9

) is off, press .

• When the Power indicator lights up red, press

on the remote

control. The Power indicator changes to green and a picture appears.

TV Set (Bottom)

With

CH

/

CH

(on remote control)

• Press

CH

, and channels change as shown below.

1 / 2 / ... / 98 / 99 / 0 / 1 / 2 ...

• Press

CH

, and channels change as shown below.

1 / 0 / 99 / 98 / ... / 2 / 1 / 0 ...

3 Adjust volume using /

.

• The number of oval blocks “ ”

indicates the volume level.

The volume bar disappears

approximately three seconds after

the volume has been adjusted.

2 Select channel.

With the number buttons (on remote control)

• To select a one-digit channel, such as 5, press

5

.

If “5-” is indicated, press

to select one-digit input, and then

press

5

again.

• To select a two-digit channel, such as 15, press

to select

two-digit input. Press

1

, and then press

5

.

• When the Power indicator lights up red, either

CH

/

CH

on the TV can be pressed to turn on

the power.

• The channel number is displayed in green for channels tuned by Auto Tuning and displayed in yellow for

channels tuned using Fine Tuning.

• When the Power indicator lights up red, the TV is in Standby mode and power is still supplied to the TV.

If you will not watch TV for a while, turn off the main power by pressing

on the TV set. Also, if

you will not be at home for a considerable length of time, unplug the cord from the power outlet.

• The AV1 (or SAV1), AV2, AV3 (or SAV3) or COMPONENT input channels cannot be selected using

CH

/

CH

on the remote control. Use

TV/VIDEO

to select these channels.

• Channels that have been skipped cannot be selected. See

20

.

• The TV set and remote control illustrations and the on-screen displays in this manual may differ from

their actual appearance.

• The TV set illustrations on this page and after are those of SX76NF100.

Remote Control

Watching a TV programme

Simple operations for watching a TV programme

CH

1

5

-- -1

PAL

51

B/G

VOLU

M

E15

03.7.30, 8:59 AMPage 12

13

• Select an appropriate volume so as not to injure your hearing.

• To avoid injuring your hearing, do not put on the headphones before plugging them into the

Headphones jack and before the power is turned on.

• The proper impedance for the headphones is 32 ohms.

• Remove the headphones plug from the Headphones jack when not using the headphones.

Operating the TV buttons

Simple operation of the TV set

Using /

Press to increase volume.

Press to decrease volume.

Using

CH

/

CH

Press

CH

, and channels change

as shown below.

1 / 2 / ... / 98 / 99 / AV1 (or SAV1) /

AV2 / AV3 (or SAV3) / COMPONENT /

0 / 1 / 2 ...

Press

CH

, and channels change

as shown below.

1 / 0 / COMPONENT / AV3 (or SAV3) /

AV2 / AV1 (or SAV1) / 99 / 98 / ... /

2 / 1 / 0 ...

Using headphones

Insert headphones plug into Headphones jack ( ) to listen to audio

with headphones.

• The audio from the speakers is turned off.

• See

29

for headphones volume adjustment.

Behind the door

TV Set (Top)

CH

VOLU

M

E15

B/G

PAL

5

03.7.30, 8:59 AMPage 13

14

Channel/Timer display

Displays the current channel number, the timer, and other

settings on the screen.

2 Press again.

• The timer displays disappear.

1 Press .

•

The time remaining on the Off

Timer, On Timer, Reminder, and the

channel number and colour/sound

system indications appear on the

screen.

• When no timer is set, the channel

number and colour/sound system

indications

appear on the screen.

Press again to turn off these

indications.

Useful features

AV MODE

1 Press .

•“ ” appears on the screen, and

the sound is silenced.

2 Press again.

• The volume returns to its previous

level.

3 Press once again.

• The channel number and colour/

sound system

indications

disappear.

Each time you press

AV MODE

, the

mode switches between STANDARD,

MOVIE, MUSIC and NEWS.

STANDARD: Normal mode

MOVIE: Movie mode

MUSIC: Music mode

NEWS: News mode

• Mute will be cancelled if is pressed at any time.

Mute

Silences the sound.

AV mode selection

B/G

0

PAL

5

OFF

ON

8:00

1:50

2:30

B/G

PAL

5

S I

(STANDARD)

(NE

W

)

(

M

OV I E )

(

M

U

S

C)

• Picture and sound can be adjusted individually for each AV mode. See

21

and

22

for details.

03.7.30, 8:59 AMPage 14

15

TV/Video selection

Switches between TV broadcasts and AV input programmes.

Each time you press

TV/VIDEO

, the

input switches between AV1 (or SAV1

when S-VIDEO terminal is used), AV2,

AV3 (or SAV3 when S-VIDEO terminal

is used), COMPONENT, and TV

programme.

Channel recall

Switches back to the channel you were watching just before

the current channel.

Press .

• The channel previously viewed returns to

the screen.

Example:

If, after switching from channel 5 to channel

7,

is pressed, the channel will

change to channel 5. Press

again

to return to channel 7.

PAL

5

7

5

7

B/G

AVS1AV1

AV2

AV3

or

AVS3

or

COMPONENT

25

PAL

B/G

TV/VIDEO

03.7.30, 8:59 AMPage 15

16

Selecting a menu item

1 Press

MENU

/

MENU/PRESET

to

call MENU screen.

3 Press / to

enter.

• The corresponding menu screen

will appear.

This TV set allows you to adjust the picture and sound, and set the channels and other features

using the on-screen display with the remote control or from the TV set. Select the desired menu

item by following the steps below and then refer to the indicated pages for details.

Remote control

2 Press

CH

/

CH

to

select desired menu item.

• The selected item is highlighted in

yellow.

• If you press and hold down

MENU/PRESET

for more than two seconds, the Language Select screen will

appear instead of the MENU screen. To display the MENU screen, press

MENU/PRESET

until the normal

screen appears, then press the button again.

• The procedures for setting and selecting the menu items on the following pages are described using the

buttons on the remote control. These procedures can also be performed using the corresponding

buttons on the TV set.

Selecting menu items

TV Set (Top)

CH

MENU

CH

MENU/PRESET

M

ENU

P I CTURE

SOUND

FEATURE

TI

M

ER

CH–SETTING

M

ENU

P I CTURE

SOUND

FEATURE

TI

M

ER

CH–SETTING

(STANDARD

TREBLE

SOUND

0

)

BASS 0

SUPER BASS OFF

SURROUND OFF

LEVEL

BALANCE 0

M

ENU

PICTURE

SOUND

FEATURE

TI

M

–

ER

CH SETT ING

CH : SELECT : ENTER

M

ENU :RETURN

(STANDARD

CONTRAS

PICTURE

T50

)

COLOUR 0

BRIGHTNESS 0

TINT

SHARPNESS 0

PICTURE NR LO

W

HITE TE

M

P0

CH : SELECT :ADJUST

M

ENU:RETURN

(STANDARD

TREBLE

SOUND

0

)

BASS 0

SUPER BASS OFF

SURROUND OFF

LEVEL

BALANCE 0

CH : SELECT :ADJUST

M

ENU :RETURN

PICTURE menu..................... SOUND menu.........................

FEATURE menu.........

CH-SETTING menu................

TIMER menu..............

––

Operation guide

BLUE BA

FEATURE

CK

ON

AUTO SELECT

TION

SAVE OFF

02

OFF

ROTA 0

CH :SELECT :ADJUST

M

ENU :RETURN

OFF

TI

M

ER

:

ON

POS I T I ON

VO

––

LU

M

E

:

CH : SELECT :ADJUST

M

ENU :RETURN

B G

ING

POS

–

ITIO

CH SETT

NCH1

COLOUR A

SOUND

SK I P OFF

ON

UTO

FINE 48.20

M

Hz

NICAM

CH : SELECT :ADJUST

M

ENU :RETURN

21 22

2926

20

3230

ON

A2

03.7.30, 9:01 AMPage 16

17

Settings and adjustments

On-screen display language selection

The on-screen display language can be set to English,

Chinese, French, Russian, Malay or Arabic.

3 Press

MENU/PRESET

until normal screen appears.

2 Press

CH

/

CH

to

select desired language.

• Pressing

MENU/PRESET

changes the

screen as shown below.

1 Press

and hold down

MENU/PRESET

for more than two seconds.

• The Language Select screen

appears.

Language MANUAL

Normal screen

AUTO

TV set

TV Set (Top)

ISH

AIS

A

M

ELAYU

E

NGL

FRANÇ

BA

H

AS

MENU/PRESET

CH

ISH

AIS

A

M

ELAYU

E

NGL

FRANÇ

BA

H

AS

03.7.30, 9:01 AMPage 17

18

Settings and adjustments

Manual channel tuning

Enables manual channel tuning to a desired TV station. (e.g.

tuning the TV to a VCR, tuning in an additional TV station.)

NOTE: This TV is already tuned into 2, 7, 9, 10 and 28.

1 Press and hold down

MENU/PRESET

for more than two seconds.

• The Language Select screen

appears.

2 Press

MENU/PRESET

twice to display

MANUAL mode screen.

• Pressing

MENU/PRESET

changes the

screen as shown below.

Language MANUAL

Normal screen

AUTO

3 Press

CH

/

CH

on

TV set or the number buttons on

remote control to select channel

position.

4 Press / on

TV set to locate channel you

wish to preset to current

channel position.

• Search is initiated and when a TV

signal is received during the

search, the search stops.

5 Repeat steps 3 and 4 above to preset channel positions for

other broadcasts.

6 Press

MENU/PRESET

again to return to normal screen.

TV Set (Top)

CH

MENU/PRESET

Number

buttons

ISH

AIS

A

M

ELAYU

E

NGL

FRANÇ

BA

H

AS

L(B G)

1

.25

M

Hz

VHF

M

ANUA

48

L(B G)

5

.50

M

Hz

Channel position

VHF

M

ANUA

107

03.7.30, 9:01 AMPage 18

19

Auto channel tuning

Automatically tunes in and presets receivable TV stations,

using consecutive channel numbers (e.g. 2, 7, 9, 10 will be

stored as 1, 2, 3, 4)

1 Press and hold down

MENU/PRESET

for more than two seconds.

• The Language Select screen

appears.

• Auto Preset stores all receivable channels including those which may be very weak and not clearly

visible. To preset only those channels designated for the local viewing region, use Manual Preset. See

18

.

• Unused channels are automatically skipped.

2 Press

MENU/PRESET

again to display

AUTO mode screen.

• Pressing

MENU/PRESET

changes the

screen as shown below.

3 Press / on

TV set.

• All the TV stations in your area

that can be received by the TV set

are automatically preset between

channels 1 to 99.

• The screen shows whatever is on

channel 1 when auto channel

preset is finished.

Language MANUAL

Normal screen

AUTO

TV Set (Top)

MENU/PRESET

ISH

AIS

A

M

ELAYU

E

NGL

FRANÇ

BA

H

AS

B/G)

1

.25

M

Hz

VHF

A

UTO(

48

B/G

PAL

1

03.7.30, 9:01 AMPage 19

20

Channel setting

Enables individual channel setting.

1 Press

MENU

to call MENU

screen.

2 Press

CH

/

CH

to

select “CH-SETTING”.

3 Press / to

display CH-SETTING menu.

4 Press

CH

/

CH

to

select desired item.

5 Each time you press / , setting for

individual items changes as follows:

• POSITION:

The channel position changes to the next higher or lower number.

• COLOUR:

• SOUND:

• SKIP: ON

OFF

Channel numbers with a “

” mark on the left are set to SKIP. To turn

off SKIP, press the number buttons to select the desired channel and

then set SKIP to “OFF”.

• FINE: The frequency changes to allow fine tuning.

• NICAM: ON

OFF

Select “ON” to receive NICAM stereo or bilingual sound signals. (See

33

for sound mode selection.) Select “OFF” to receive NICAM

mono signals.

• A2: ON

OFF

Select “ON” to receive A2 stereo or bilingual sound signals. (See

34

for sound mode selection.) Select “OFF” to receive mono

signals.

• Switching COLOUR system:

Set the system to “AUTO” for normal TV reception. The AUTO mode automatically detects the received

signal system and changes the reception system of the TV set. When the picture is not stable, switching

to an appropriate system may improve the picture quality.

• In a weak reception area, or under bad reception conditions, you can change the frequency by Fine

Tuning.

• When using Fine Tuning (FINE), the channel number changes from green to yellow.

• To return the channel to its original frequency setting, follow the manual channel tuning procedure. See

18

.

6 Press

MENU

until normal

screen appears.

AUTO PAL

N443

SECAM

N358

Settings and adjustments

B/G I

D/K

M

CH

MENU

M

ENU

P I CTURE

SOUND

FEATURE

TI

M

ER

CH–SETTING

2

1

MON

A2 ON

B

G

ING

POS I T IO

CH–SETT

NCH7

COLOUR A

SOUND

SKIP OFF

UTO

FINE 68.25

M

Hz

NICA

AV

ING

POS I T I O

CH–SETT

N1

COLOUR AUTO

AUTO PAL

N443

SECAM

N358

• When you select AV1, AV2 or AV3 for the channel position, the CH-

SETTING menu changes as shown above and the colour mode

changes in the following order:

03.7.30, 9:01 AMPage 20

Page is loading ...

Sharp SX76NF100 User manual

This manual is also suitable for

Sharp SX76NF100 User manual

Related papers

Other documents