INKELTECH SBL001-Kit Installation guide

Brand
INKELTECH
Model
SBL001-Kit
Type
Installation guide
0
contact@inkeltech.com
1
Installation Guide
1. Setting up the Light Stand:
Unfold the legs and adjust the height of the light stand to your desired position.
2. Setting up the Softbox:
3. Setting up the LED Bulb:
1. Install the softbox to the top of light stand and tighten
the second screw;
2. Loosen the first screw to adjust the angle of the softbox
to your desired position and tighten it.
1. Push the metal circular ring to the light socket;
2. Screw the LED light bulb into the socket.
2
4. Connecting the LED Bulb with the Remote Control:
5. Setting up the Camera / Phone Tripod:
1. Press the “ON/OFF” button on the power cable to turn on the light;
2. Press the “SETUP” button on the remote control within 10 seconds after
the light turned on;
3. The light flashes once means that the LED bulb and the remote control
connected successfully;
4. If the connection is not successful, please press the “ON/OFF” button
again to turn off the light and repeat the previous steps until the light
flashes once.
1. Open the lock catch to adjust the height of the tripod to your
desired position;
2. Screw your camera to the standard 1/4" screw on the tripod tip;
3. Or screw the phone holder to the standard 1/4" screw on the
tripod tip to hold your smart phone.
3
6. Function of Each Part of the Camera / Phone Tripod:
Adjusting the height of the tripod: Loosen the screw, adjust to the height you want and
tighten.
Adjusting the angle: Loosen the
handle, adjust (move the handle up or
down), and tighten.
Adjusting the Camera / Phone: Loosen
the screw, adjust the camera or phone
(across a 90-degree angle), and tighten.
Adjusting the Camera / Phone: Loosen
the screw, rotate the holder (across
360-degrees horizontally) and tighten.
4
Softbox Light Instructions
1. Technical Information
Model
Adjustment range
Color temperature
Flash index
Dimension(mm)
2. What's in The Box
NO
NAME
QTY
①
Softbox with Power Cable
2
②
Light Stand
2
③
50W Dimmable LED Light Bulb
2
④
Remote Control
1
⑤
Phone Holder
1
⑥
Bluetooth Selfie Remote
1
⑦
White Diffuser
2
⑧
Camera / Phone Tripod
1
⑨
Travel Bag
1
5
3. Operation Instructions
3.1 Take out the light from the bag, assemble according to steps, then plug the power
cable, the LED light will turn on.
3.2 Press the “SETUP” button on the remote control within 10 seconds after the light
turned on;
3.3 The light flashes once means that the LED bulb and the remote control connected
successfully;
3.4 If the connection is not successful, please press the “ON/OFF” button again to turn
off the light and repeat the previous steps until the light flashes once.
3.5 Use the remote to control the light. The color temperature range of the light: 3000
~ 6500 K, the brightness range of the light: 0% ~ 100%.
6
4. Care Guidance
► Please protect the device from impacts, humidity, dirt, marked temperature
fluctuations, and direct sunlight.
► Do not drop the device.
► Please don’t touch the light. Do not expose it to rain or moisture (to avoid a
short-circuit).
► Please be careful with handling the light during and after use as the device may be
hot and may burn you.
5. Warranty/service
In case of a claim under the warranty please contact your local distributor. In case of
returning the unit please add a copy of your receipt and a short report of the defect.
The following warranty terms shall apply:
1. The warranty period for this product is 1-year from the date of purchase. In case of
a warranty claim, the date of purchase must be proven by means of the sales receipt
or invoice.
2. Repairs (complete unit or parts of the unit) do not extend the warranty period.
3. The warranty shall not be valid for damages because of
a. Improper treatment, e.g. nonobservance of the user instructions.
b. repairs or tampering by the customer or unauthorized third parties.
c. transport from the manufacturer to the consumer or during transport to the
service center.
d. The warranty shall not be valid for accessories which are subject to normal
wear and tear
4. Liability for direct or indirect consequential losses caused by the unit are excluded
even if the damage to the unit is accepted as a warranty claim.
*Upgrading the goods, the right of finally interpretation belongs to our company.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

INKELTECH SBL001-Kit Installation guide

Brand
INKELTECH
Model
SBL001-Kit
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents