Sangean WFR-28 Owner's manual

GB

Revision 2

WFR-28D / WFR-28

1

Contents

Introduction ...................................................................................... 2-6

Before you can use this product ...................................................... 2-3

Controls and connections ............................................................... 4-5

Navigation controls ............................................................................ 6

Network conguration ................................................................... 7-15

Connecting your radio to your computer network ......................... 7-14

Network remote control options ....................................................... 15

Internet Radio mode .................................................................... 16-28

Internet Radio-the basics ................................................................. 16

Selecting a radio station by location and genre .......................... 17-19

Searching for a radio station by name ............................................. 20

Searching a new or popular station ................................................. 21

Selecting a podcast/ BBC Listen Again ........................................... 22

Presetting stations ........................................................................... 23

Display modes ................................................................................. 24

Customizing your radio .................................................................... 25

Selecting favorite stations ........................................................... 26-28

Music Player mode ...................................................................... 29-44

Use with Windows, Apple Mac and Linux ........................................ 29

Accessing your les via UPnP .................................................... 30-31

Locating and playing media les using UPnP .................................. 32

Media selection ................................................................................ 33

Controlling playback ................................................................... 34-35

Display modes ................................................................................. 36

Playlists ...................................................................................... 37-39

Wake On LAN .................................................................................. 40

Prune servers .................................................................................. 40

Windows 7 ‘Play to’ function (UPnP renderer) ............................ 41-42

Using USB memory devices ....................................................... 43-44

DAB mode .................................................................................... 45-52

Selecting a DAB radio station .......................................................... 46

Display modes ................................................................................. 47

Finding new DAB radio stations ...................................................... 48

Manual Tuning ................................................................................. 49

Dynamic Range Control Settings ..................................................... 50

Station order setup .......................................................................... 51

Prune stations ................................................................................. 52

FM mode ....................................................................................... 53-58

Manual tuning ............................................................................. 54-55

Scan setting ..................................................................................... 56

Stereo/ Mono switching ................................................................... 57

Presetting stations in DAB and FM modes ...................................... 58

Clock and Alarms ......................................................................... 59-67

Automatically updating the clock ...................................................... 59

Setting the clock format ................................................................... 60

Manually setting the clock ........................................................... 61-62

Setting the alarm clock ............................................................... 63-65

Snooze timer .................................................................................... 66

Disabling alarms .............................................................................. 66

Sleep timer ....................................................................................... 67

Display and Auto .......................................................................... 68-74

Equalizer function ............................................................................ 68

Brightness control and Contrast/ viewing angle control .............. 70-71

Headphone socket and Line out socket ........................................... 72

Auxiliary input socket ....................................................................... 73

Information ................................................................................... 74-82

Factory reset .................................................................................... 74

Software update ............................................................................... 75

Network proles ............................................................................... 76

Software version display and Audio FAQ ......................................... 77

Accessing your audio files via a UPnP server using Windows Vista

and XP ........................................................................................ 78-79

Audio codecs ................................................................................... 80

Cautions and Specications ....................................................... 81-82

2

GB

Before you can use this product

Before you can use your internet radio, you must have the following:

● A broadband Internet connection (not required for DAB, FM or Music

Player functions).

● A wireless access point (WiFi) connection connected to your broadband

Internet Service Provider, preferably via a router. In many cases the

broadband modem, router and wireless access point will be a single

combined unit supplied by your Internet Service Provider or bought

from a computer store.

● If your wireless network is congured to use Wired Equivalent Privacy

(WEP) or WiFi Protected Access (WPA/WPA2) data encryption then

you either need to know the WEP, WPA or WPA2 key used for encryption

so you can get the internet radio to communicate with the network, or

your router needs to offer WiFi Protected Setup (WPS).

If connecting using WiFi, the internet radio will typically work within a

10-20 metre radio from your wireless access point. The actual range

achieved will depend upon the building type, other nearby wireless

network, and possible interference sources. DAB and FM radio

functions can operate wherever the internet radio is able to receive a

suitable broadcast signal.

IMPORTANT:

Before you continue, make sure that your wireless access point or

router is powered up and working with your broadband Internet service

(use your computer to verify this). To get this part of the system working

you must read the instructions supplied with the wireless access point

or router.

Battery operation

Battery operation using alkaline batteries

1. Remove the battery cover on the rear of the unit by pressing the catch.

Note:

Before you insert the batteries, if you use non-rechargeable batteries,

make sure the NiMH/Alkaline switch which located inside the battery

compartment is switched to Alkaline position. If you use rechargeable

batteries, make sure to switch NiMH/Alkaline switch to NiMH position.

2. Insert four UM-1 (D size) batteries into the spaces in the compartment.

3. Take care to ensure all batteries are inserted with correct polarity as

shown on the rear cabinet. Replace the battery cover.

4. Reduced power, distortion and a “stuttering sound” are all signs that

the batteries need replacing.

5. If the radio is not to be used for any extended period of time, it is

recommended that the batteries are removed from the radio.

3

Battery operation using rechargeable batteries

1. Slide the battery switch to the NiHM position.

2. Insert 4 UM-1 batteries into spaces in the compartment. Make sure

all batteries are inserted with the correct polarity as shown on the

rear cabinet. The radio is also designed to be used with NiMH

rechargeable batteries.

Note:

Do not use a mix of old and new rechargeable batteries.

Do not use a mix of full and empty rechargeable batteries.

Do not use batteries that have a different mAh capacity

Do not use damaged or leaking batteries

3. Make sure the radio is switched off and connected to the AC adaptor.

When the charge indicator flashes yellow indicating batteries are

charging. Batteries will be fully charged in around 10 hours. The battery

shows steady yellow light when the battery charging is complete.

Note:

Duration for charging your battery fully can be varied according to

the mAh capacity of a battery. Higher mAh batteries required longer

charging time.

Using the AC power adaptor

The AC power adaptor required for this unit should be 7.5 volts DC at 1.6

A center pin positve.

Insert the adaptor plug into the DC socket on the left side of the radio.

Plug the adaptor into a standard mains socket outlet.

Whenever the adaptor is used, the batteries are automatically

disconnected. The AC adaptor should be disconnected from the main

supply when not in use.

4

GB

Controls and connections

1. USB memory socket

2. Mode button

3. LCD display

4. Info button

5. Menu button

6. Back button

7. Forward button

8. Standby button

9. Battery charge indicator / Low battery indicator

10. Tuning Control Rotary/ Select knob

11. Volume button

12. Mute button

13. Preset 5/ Stop button

14. Preset 4/ play/ pause button

15. Preset 3

16. Preset 2/ Rewind button

17. Preset 1/ Fast-forward button

18. Loud speaker

5

19. FM telescopic aerial

20. Auxiliary input jack

21. Line out jack

22. Headphone jack

23. DC in jack

24. Battery compartment

25. Alkaline/NiMH/NiCad rechargeable battery switch

6

GB

Navigation controls

This page describes the basic means of controlling your WFR-28D internet radio.

Instructions for each operating mode are given in the later section of this book.

1. Pressing the Standby button brings your radio out of Standby mode. Pressing Standby while

the radio is in use will cause it to return to the Standby mode with the clock display.

2. Pressing the Mode button gives you access to each of the operating modes in turn: Internet

Radio, DAB+ radio, Music player, FM radio and Auxiliary Input.

3. Pressing the Menu button will access the menu system, whereas the Info button allows the

display of information relating to the radio station or music le being played.

4. Many operations require the user to make a selection from the menu. Highlight the menu item

using the Tuning Control Rotary on the right side of the radio. Press the Tuning Control Rotary

to select that item. If there are more than ve items in a menu, then the display will automatically

scroll up or down so that the additional items become visible. A sliding bar on the right will give

an indication showing the current portion of the menu that is displayed. If there are many items

in a menu, then the radio allows the menu to “wrap around” in either direction. This can make

it easier to reach items at the end of a long menu, such as a list of countries or Internet radio

stations.

5. If an error is made when navigating the menus, it is generally possible to go back to a higher

level menu by pressing the Back button.

Internet radio

Music player

DAB

FM

Main menu

1

MOD E

2

MEN U

3

INF O

3

SELECT

/SEEK

4

BAC K

5

7

Conguration

Connecting your radio to your computer network

1. Place your radio on a at surface and plug the mains lead into the mains socket located on the

left side of your radio ensuring that the plug is pushed fully into the socket.

2. Plug the other end of the mains lead into the wall socket and switch on the wall socket.

IMPORTANT: The mains plug is used as the means of connecting the radio to the mains supply.

The mains socket used for the radio must remain accessible during normal use.

In order to disconnect the radio from the mains completely, the mains plug should be removed

from the mains socket outlet completely.

3. When you apply power, the display on the radio will light up and say: ‘SANGEAN’ and ‘STARTING’

with a progress indicator. The rst time that you use your radio (or after Factory Reset) the

display will show “Setup wizard” and “YES” will be highlighted on the screen. Press the Tuning

Control Rotary to start the setup wizard. The screen will ask if you wish to run the setup wizard

again at the next start up. This will lead to the main menu.

4. Rotate the Tuning Control Rotary on the right hand side of the unit to highlight the desired

clock format (either 12 or 24 hour) then press the Tuning Control Rotary to enter your selection.

A menu allowing you to specify the auto update option for the clock will appear on the display.

The default of ‘Update from Network’ will be the best option for most users.

SANGEAN

SELECT

/SEEK

3,4

8

GB

5. Rotate the Tuning Control Rotary to choose an auto-update option for the clock. This can be

updated from DAB or FM radio, from the Network, or not updated. The default is to auto update

from the network. If you choose any other option, go to step 8. Otherwise you will rst need to

select the correct time zone and daylight savings setting, see steps 6 and 7. If you choose

“No update” you will need to set the clock manually later( see the section of ‘Manually setting

the clock’). Press the Tuning Control Rotary to conrm your choice.

6. Rotate the Tuning Control Rotary to highlight the time zone which is applicable to your location.

Press the Tuning Control Rotary to enter the setting.

7. You will then need to set the Daylight Savings option according to your location (Daylight

Savings is also known as Summer/Winter time ). Rotate the Tuning Control Rotary to highlight

“YES” to turn on daylight savings if required or ‘NO’ if you do not wish to use daylight savings

then press the Tuning Control Rotary to conrm the setting.

8. The display will then show a list of WiFi regional options for the network set up. Rotate the

Tuning Control Rotary to highlight the required region and then press the Tuning Control

Rotary to select it. Your radio will then scan for available WiFi networks.

9. The radio will enter the Network Settings Wizard and will display ‘Scanning…’. After a short

while the display will show a list of the available WiFi networks.

[Manual config]

SELECT

/SEEK

5-8

9

10.

11.

12.

13.

You will first need to identify your network in the list of network names presented by the

Network Wizard. If no networks are found then you may have to get your wireless router wor-

king (please see the instructions supplied with it) or you may be too far from the router.

When the radio nds your wireless network, it displays the Network Name (SSID) for the wi-

reless access point on the screen. This is a name that is allocated to the access point in your

router by the person who set up the network – for example: ‘Jones family’ or ‘Paul’s network’.

If the router supports WiFi Proteced Setup, then ‘[WPS]’ will be shown in front of the SSID. It

is possible, and in some locations highly likely, that your radio will nd more than one wireless

network, in which case you should choose which one you need to connect to.

Rotate the Tuning Control Rotary to see the SSID for each wireless network that has been

found. If your network is shown proceed to step 14. If it is not shown then proceed to step 12.

If you make a mistake at any point, use the Back button to go back to the previous screen.

If your network is not found, it may be because the router is congured not to broadcast the

SSID. You should then use the Tuning Control Rotary to highlight and select the ‘[Manual

cong]’ option in order to enter the network details manually. This is described in ‘Manual

Network Conguration”. If your network name is being broadcast, and it was not found, then

try re-scanning press the Back button), and if necessary try moving your radio to a location

closer to your access point / router.

When the SSID for the wireless network you wish to connect to is highlighted on the screen,

press the Tuning Control Rotary. If WiFi Pretected Setup (WPS) was indicated, you will see

an additional menu at this point, otherwise proceed to step 14. choose one of the WPS menu

options as required for your router (WPS may be via push button, or using an identication

number).

‘Push Button’ – the display prompts you to press the WPS button on your router and then

the Select button on the radio. The two devices should then connect with the encryption key

sent automatically to the radio.

‘PIN’ – the display shows an identication number which you must enter into your router

using a web browser (refer to your router’s user documentation). You should then press the

Select button on the radio.

‘Skip WPS’ – if you wish to enter the encryption key yourself (or if it was previously Entered).

If you choose Push Button or PIN the screen will then show ‘Connecting…’ and then ‘Setup

wizard completed’. Press the Tuning Control Rotary to exit setup wizard.

SELECT

/SEEK

11-13

BA C K

11,12

10

GB

14.

15.

16.

If your network is congured without an encryption key, the screen should say ‘Connecting…’,

and then ‘Setup wizard completed’. Press the Tuning Control Rotary to exit the setup wizard

and show the main menu. If this is the case then you have successfully connected your radio

to your network.

If the screen displays ‘Key’ , it is because the network is using one of the encryption systems:

Wired Equivalent Privacy (WEP) or WiFi Protected Access (WPA). You will need to enter the

correct WEP or WPA key into the radio to allow it to communicate with your wireless network.

If you do not have the WEP or WPA key, then you should obtain it from the person who set up

your network. Some wireless routers may come with an encryption key already set up by the

supplier, in which case you should refer to the documentation provided with it. WPA is used

here to also include WPA2.

WEP keys are 10 or 26 characters long (using 0 – 9, and A – F). Some wireless Routers can

also use pass-phrases for WEP but these are not supported. WPA keys are usually set up

using a pass-phrase of between 8 and 63 characters.

Your radio accepts pass-phrases for WPA keys.

To enter the WEP or WPA key, characters are selected and entered using the Tuning Control

Rotary. The highlight scrolls through the available characters as well as the three controls on

the right.

The character currently highlighted will be entered when you press the Tuning Control Ro-

tary. Do this as needed until the complete key has been entered. Remember, WEP keys only

use the numbers 0-9 and letters A-F. WPA keys are sensitive to upper and lower case charac-

ters. You must enter the key exactly or the radio will not connect to the network.

The three controls on the right-hand side of the screen have special functions. You can quic-

kly access these by pressing the Info button and then use the Up or Down and Select buttons

as needed:

select ‘ ’ to erase a character just entered

select ‘ ’ when the complete key has been entered

select ‘ ’ to cancel an re-run the Network Wizard

If a WEP or WPA key has previously been entered for the selected SSID then the display will

show ‘Key: [Set]’. If you have previously entered a different key, you must clear this by selec-

ting the ‘ ’ symbol. This will remove the ‘[Set]’ indication.

After the nal character of the WEP or WPA key has been entered, highlight the ‘ ’ symbol

and press the Tuning Control Rotary. Then screen will show ‘Connecting…’ and then ‘Setup

wizard completed’. Press the Tuning Control Rotary to exit setup wizard. The radio should

now be able to connect to the network.

DAB

11

17.

Once you have connected your radio to the network (and therefore also to the Internet) it will

display the main menu. Press the Tuning Control Rotary to put the radio in Standby mode.

It should then display the time as obtained from the Internet. If the time display is not correct

for any reason, it can easily be adjusted later, see ‘Manually setting the clock’.

If you have followed the steps on the preceding pages successfully, your radio will have

connected to your router, and then made a connection to the Internet and set its clock.

If this is the case, then you can try listening to radio stations via the Internet.

Note: To save the radio power consumption while your radio is powered with battery, the

radio will turn off fully when put into standby mode. As a result, if you switch off your radio

when your WFR-28D is power supplied with battery, next time when your radio is switched

on, the time on the screen will be reset and show as ‘00:00’ . However, as soon as the radio

connects with WiFi, the time will update automatically from the network.

12

GB

Changing the network connection

In the sections above, you chose how your radio would be connected to your network, using a

WiFi connection. From time to time, you may nd that you need to connect to different computer

networks. The Internet setup menu allows you to change your radio’s network settings, scan for

an alternative wireless network, or to manually congure the network parameters.

The steps outlined below describe how you can do this –see also the section ‘Network Proles’.

Conguring the radio to use an alternative WiFi connection

From the Network settings menu select ‘Network wizard’. This will present you with details of

any WiFi networks that are found. Scroll down the list using the Tuning Control Rotary to the

desired network name. Press Tuning Control Rotary to select this network. The radio will then

use its WiFi system to communicate with the network. Depending on the settings for the new

network you may need to enter an encryption key. By default the radio will then acquire an IP

address and other network settings from your router using DHCP.

Manual network conguration

If you do not wish to use DHCP for automatic conguration, or if your network is congured with

a hidden SSID, then you will need to enter some network settings manually. (Note – a hidden

SSID may prevent casual observers from detecting your network, but is not recommended

as a means of network security.)

1. From the radio Network settings menu, select ‘Manual settings’. You must then choose to connect

using ‘Wireless’ connections. Entering this option, there are as many as nine settings screens,

shown by the ‘1 of 9’ progress marker in the top right corner of the display.

2. The next menu asks whether you wish to use DHCP to configure your network parameters

(IP address, subnet mask, gateway address, etc). Unless you are familiar with networking and

related terminology, we recommend that you allow the use of DHCP. Choose ‘DHCP enable’

unless you need to specify the network details manually.

If you chose ‘DHCP enable’, please skip to step 6 in order to set up the wireless connection details.

If you chose ‘DHCP disable’ for either connection method, the next step is to set up the IP address.

13

3.

4.

5.

6.

7.

The manually specied IP address should be chosen to be compatible with the settings in your

router and must be a unique address on your network. If you are using DHCP for some devi-

ces and static (manually congured) IP addresses for others, the IP address used should fall

outside the range that the router may allocate using DHCP. Typically, the rst three groups

of digits will be the same for all devices on your network. To enter the IP address, rotate the

Tuning Control Rotary to set the value for each group of digits and then press the Tuning

Control Rotary to enter the value and to move on to the next group.

When the IP address has been entered, the subnet mask should be entered. The subnet mask

defines which parts of the IP address are common across your network. For most small

networks the subnet mask will be 255.255.255.0 and this is entered in the same way.

The Gateway address is normally the IP address of the router through which the radio

connects to the internet and is entered in the same way as the previous addresses.

In most installations the DNS settings (DNS = Domain Name Server) will be set to the same IP

address as your router. In this case the secondary DNS may be left at zero. To enter the DNS

address, rotate the Tuning Control Rotary to set the value for each group of digits and then

press the Tuning Control Rotary to enter the value and to move on to the next group. Repeat

this until all eight groups of digits have been entered.

The next step is to set up the WiFi connection, starting with the name of the wireless network

(SSID) followed by the encryption options and password. To enter the SSID, characters are

selected and entered using the Tuning Control Rotary The radio scrolls through the available

characters as well as the three controls on the right. The character currently highlighted will

be entered when you press the Tuning Control Rotary. Do this as needed until the complete

network name has been entered. The SSID setting is sensitive to upper and lower case cha-

racters and symbols.

You must enter it exactly as set up in your router. The three controls on the right-hand side of

the screen have special functions:

select ‘ ’ to erase a character just entered

select ‘ ’ when the complete SSID has been entered

select ‘ ’ to cancel and go back to the DNS settings screen

Having entered the SSID, you must enter details of the encryption system used on your wi-

reless network. This should be the same as specied in your router settings. If your network

does not use encryption, then select the ‘Open’ option. Your radio should then connect to the

network, so skip to step 11. If your network uses WEP (Wired Equivalent Privacy) select the

‘Pre-Shared Key’ option then go to step 8. The remaining options are for WPA or WPA2 (WiFi

Protected Access) – see step 9.

14

GB

8.

9.

10.

11.

If you chose ‘Pre-Shared Key’ in step 7, you should then choose the WEP option. The key

should be entered using only the numbers 0-9 and the letters A-F. The key will be 10 charac-

ters long for 64-bit encryption and 26 characters long for 128-bit encryption. The radio will

accept lower-case letters a-f as equivalent to upper-case A-F. Spaces or special symbols are

not permitted in WEP keys.

The three controls on the right-hand side of the screen have special functions:

select ‘ ’ to erase a character just entered (long press to clear); Info again to continue

select ‘ ’ when the complete encryption key has been entered

select ‘ ’ to cancel and go back to the SSID settings screen

Once the key is entered the radio should connect to your network. Please skip to step 11.

WPA and WPA2 are similar, although WPA2 offers a higher level of security. Whichever

you selected in step 7, you then have to specify the variant used. They are TKIP (Temporal

Key Integrity Protocol) and AES (Advanced Encryption Standard). As previously, the setting

should match that used by your router. Some routers allow both to be specied, and the rou-

ter will use whichever variant is supported by the connected device. AES is regarded as the

more secure option if it is available.

The radio will then require you to enter the encryption key. This must be a string of between 8

and 63 characters and must be identical to the key which has been entered into your router.

Note – the encryption key is sensitive to the use of upper and lower case letters and symbols.

Take care to enter the key exactly, or the radio will not be able to connect to your router. The

three controls on the right-hand side of the screen have special functions. You can access

these by rotating the Tuning Control Rotary and then press the Tuning Control Rotary to

select as you needed:

select ‘ ’ to erase a character just entered (long press to clear ); Info again to continue

select ‘ ’ when the complete encryption key has been entered

select ‘ ’ to cancel and go back to the TKIP / AES options screen

Once the key is entered the radio should connect to the network.

While the radio is trying to connect to the network, it will display ‘Processing…’ when chec-

king the encryption key and then ‘Connecting…’.

If the connection is made successfully, the radio will return to the Network settings menu.

If the unit cannot connect, then it will display a ‘Failed to connect’ message and will return to

the SSID entry screen (step 6).

Once connected, the network settings are stored in the radio. The settings are retained when

the radio is disconnected from the mains.

You may now use the Back and Mode buttons to access the functions of your radio.

15

Network remote control options

Network Pin setup (Pin number)

Your radio has the option of being controlled by an application installed on an Apple iPhone, iPod

touch or iPod. The Pin number facility allows you to ensure that your radio can only be controlled by

your own Apple device rather than someone else’s.

Details of how this feature can be used with your iPhone or iPod touch are explained in the separate

section in this manual called ‘Using iSangean app for controlling your WFR-28 internet radio’.

Keep network connected

By default, your radio will shut down its WiFi connection when it is in standby. This minimizes power

consumption but it does mean that you will need to switch that radio on manually in order to use

either the ‘Play to’ function or any other remote control software.

If you need to be able to remotely control the radio even when it has been put into standby, then

you can choose to keep the network connected by using the ‘Keep connected’ option in the network

setting menu. In the standby mode display either the WiFi signal indicator is shown with or without a

cross through it according to the chosen network settings.

Keep network connect

Wlan region

Manual settings

Network PIN Setup

Network profile

>

Network settings

Keep network connect

Wlan region

Manual settings

Network PIN Setup

Network profile

>

Network settings

06/04/2011

16

GB

Internet Radio

Internet Radio – the basics

Before you can use your radio to listen to broadcasts via the Internet, it is necessary to have

connected it to your computer network using the wireless (WiFi) connection .

There are literally many thousands of radio broadcasts available via the internet as well ‘Podcasts’.

Your radio provides several ways of searching for broadcasts in order to make nding and choosing

them easier. Once you have found radio stations which you like, you may either store them as presets

within the radio, or add them to a list of your favorite stations which your radio can access. The

number of presets is limited (there are ve presets in the radio), but you can store as many favorites

as you like.

You may search for an internet radio station by Location. If you know the name of the station and the

country from which a station is broadcast this may be the easiest method to nd a station. It is also a

great way to experience radio from other parts of the world.

You may also search for an internet radio station by Genre. If you prefer a particular type of music,

Blues for example, you may search for a radio station that broadcasts that type of music, and you can

choose from a list of Blues radio stations regardless of location, or taking location into account.

If you know part of the name of an internet radio station, you can enter it into the radio and it will

search for stations that match that name. This can be helpful if you are unsure of the location or genre

of a particular station.

The WFR-28D radio connects to a radio station database which serves many users in many

countries. This means that there is a very wide range of program content available. You can also

search for stations which have been recently added to those available (new stations) or you can

search for the most popular.

17

Selecting a radio station by location

1. Press the Standby button to switch the radio on. Then press the Mode button to select the

internet radio mode display.

2. Press the Menu button to enter the main Internet radio menu. Rotate the Tuning Control Rotary

until ‘Station list’ is highlighted on the display and then press the Tuning Control Rotary to select

the option.

3. Rotate the Tuning Control Rotary until ‘Stations’ is highlighted on the display and then press

the Tuning Control Rotary.

Note that the menu may offer one or more local selections based upon the country in which

the unit is being used, according to your internet IP address (‘United Kingdom’and ‘BBC’ stations,

for example).

4. Rotate the Tuning Control Rotary until ‘Location’ is highlighted on the display and then press

the Tuning Control Rotary to select.

5. Rotate the Tuning Control Rotary to scroll through the list of continents. When the desired

continent is highlighted press the Tuning Control Rotary to enter your selection.

6. The display will show a list of countries within the chosen continent. If there are many countries

shown you can scroll through the list continually in either direction.

For example, if the chosen continent was Europe, then to nd the United Kingdom scroll up

from the top of the list to the bottom by rotating the Tuning Control Rotary. Press the Tuning

Control Rotary to choose the desired country.

7. You will typically nd that you then have the option to select either ‘All Stations’ or one of a

number of categories. The lists are always sorted alphabetically, and long lists will wrap around

from top to bottom or bottom to top.

SELECT

/SEEK

MOD E

1

3-6

MEN U

2

18

GB

8. Rotate the Tuning Control Rotary to highlight your chosen radio station and then press the

Tuning Control Rotary to enter your selection. The display will show ‘Connecting…’ while the

radio connects to the new station. The station should then start playing. Adjust the volume as

needed.

9. If the station has on-demand content, that is, it gives the option of listening to programs which

have already been broadcast or to Podcasts, there will be an additional screen showing the

radio station name as well as a ‘Podcasts’ option.

These are selected using additional menus, determined by the radio station and the content.

There may simply be a list of programs, or there may also be options to choose from broadcasts

on particular dates or days of the week. The examples shown here are typical.

Podcasts and Listen Again content can also be accessed separately from the main Internet

Radio menu.

If your radio cannot connect to a radio station

Note: If your radio is unable to connect to an internet radio station it will generally either display

‘Network Error’ or ‘Stopped’. This can be for many reasons, but typically will be due to one of the

following:

● The radio station may not be broadcasting at the present time.

● The radio station may not be able to accommodate any more connections from internet listeners.

● The broadcaster may limit listening to specic countries or regions.

● There may be network congestion (either locally or at a distance) which is affecting the reliability

of the connection.

If your radio can connect, but the audio is not continuous and the radio keeps having to

reconnect, this may be due to the radio station only having limited connection capacity.

19

Selecting a radio station by genre

1. Press the Menu button to enter the main Internet radio menu.

2. Rotate the Tuning Control Rotary until ‘Stations’ is highlighted on the display and then press

the Tuning Control Rotary to select.

3. Rotate the Tuning Control Rotary until ‘Genre’ is highlighted on the display and then press

the Tuning Control Rotary.

4. Rotate the Tuning Control Rotary to scroll through the list of content types.

This menu is normally cyclic – you can scroll the list continually in either direction. When the

chosen genre is highlighted, press the Tuning Control Rotary.

5. You then have the choice of ‘All Stations’ of the chosen genre, or a list of countries. Note if a

country is not shown then the station may still appear in the ‘All Stations’ list. Rotate the Tuning

Control Rotary and the Tuning Control Rotary to choose as needed.

6. A list of radio stations is then shown. Rotate the Tuning Control Rotary until the desired station

name is highlighted on the display.

7. Press the Tuning Control Rotary to select the station. The display will show ‘Connecting…’

while it nds the new station. If the radio is unable to connect this may be for one of the reasons

explained previously.

8. Adjust the Volume as needed to set the listening level.

SELECT

/SEEK

2-7

MENU

1

Page is loading ...

Sangean WFR-28 Owner's manual

This manual is also suitable for

Sangean WFR-28 Owner's manual

Related papers

Other documents