Hama 00092660 Owner's manual

00092660/06.09

All listed brands are trademarks of the corresponding companies. Errors and omissions excepted,

and subject to technical changes. Our general terms of delivery and payment are applied.

Hama GmbH & Co KG

D-86651 Monheim/Germany

www.hama.com

00092660

Baby - Control

»BC-300«

THE SMART SOLUTION

Page is loading ...

14

g Operating Instruction

15

Receiver

1. Soft Antenna 5. Belt Clip

2. Volume Control 6. Hanging Hook

3. Power Control / Channel Switch: 7. Battery Compartment

OFF/CH1/CH2 8. AC/DC Power Supply Socket

4. Speaker

Main LCD Screen

Transmitter Receiver

AC Adapter

Desktop charger stand

Supplied

rechargeable batteries

Out of range alarm icon

Channel:CH01/CH02

Baby sleeping icon (energy saving mode)

Battery icon:

Baby calling icon: constantly changing

display-readouts

Full battery level

Low battery level, reminds you to change the

batteries

Empty and ﬂ ashing, batteries change is a must

You have just purchased a qualiﬁed baby monitor. Please read the

instructions thoroughly before using the monitor system and keep it for future

reference.

Content and Features

Transmitter

1. Soft Antenna 4.Microphone

2. Sensitivity Control :0-8 level 5. Belt Clip

3. Power Control / CHANNEL Switch: 6. Hanging Hook

OFF/CH1/CH2 7. Battery Compartment

8. AC/DC Power Supply Socket

16 17

AC Adaptor:

The AC Adaptors are low voltage power source that allow you to use

your household electricity to run the Baby Monitor. Connect the AC

Adaptors to the AC Adaptor Jack in the Parents and Baby Unit. Both

plug into any standard volt electrical outlet in your home. It is

recommended to turn off the units before plug in or unplug the

adaptors.

CAUTION: These adaptors were made with a speciﬁc design for this

product. They cannot be used with any other appliance. Never use a

different type of adaptor with Baby Monitor.

CAUTION

This product cannot replace responsible adult supervision.

• This Baby Monitor is intended as an aid. Do not use it as a medical monitor or

a substitute for responsible and proper adult supervision.

• Make sure the Receiver and adaptor cable are always out of child‘s reach. Do

not place the Receiver inside the baby‘s crib or playpen!

• The antenna on the Units are ﬁ xed, do not try to extend them. Never attempt to

modify the product.

• Avoid using the product near water and expose to rain or moisture.

Receiver & Transmitter Battery Installation

1. Locate the battery compartment door on the

back of the Units.

2. Open the battery compartment door.

3. Insert 3 * AAA batteries into the Receiver and

the Transmitter according to the +/- signs shown

in the battery compartment, respectively.

4. Replace battery compartment doors.

Battery Tips:

• If the product is not in use for a long time, disconnect both units from the

household electrical outlet. And remove the batteries or the exhausted

batteries from the units, otherwise battery leakage and corrosion can damage

them.

• Non-rechargeable battery is not to be recharged

• Rechargeable batteries are only to be charged under adult supervision.

• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace

only with the batteries of the same and equivalent type.

Transmitter & Receiver Battery Charging

If the battery level becomes low, in both LCD displays the empty battery icon.The

battery icon and the out of range alarm icon ﬂ ash, in order to warn you about the

low battery level. The receiver also emits a warning tone continually.

Charging the batteries

Please charge the rechargeable batteries ﬁ rst time usage.

The rechargeable batteries to the transmitter and receiver must not be taken out

of the units for charging. The battery icon loops and ﬂ ashes while charging. It

stops ﬂ ashing when the batteries are fully charged.

Charging the transmitter

1. Connect the power supply unit to the thin plug on the 6V-socket of the

transmitter.

2. Once the power supply unit is connected to the transmitter, charging

automatically begins.

3. The charging time for completely charging empty battery takes about 9 hours

when the transmitter is turned off.

Charging the receiver

1. Connect the power supply unit to the thick plug on the charger stand socket.

2. Once the power supply unit is connected to the charger stand and the receiver

is on the charger stand, charging automatically begins.

3. The charging time for completely empty batteries and turned off unit is

about 9 hours.

Remarks:

1. Use only the DC adaptors or desktop charger stand which are included in the

package. Plug into any nearby standard household electrical outlet.

18 19

2. And connect them with the units.

3. Supply Power : DC 6V

Note:

• User can also install 3 alkaline AAA batteries instead of the supplied

rechargeable batteries.

• Or directly operated by the supplied adaptors.

Testing Before First Time Usage

Test the Transmitter emission and the Receiver reception.

• Place Transmitter and Receiver in room where you intend to use it.

• Set both Transmitter and Receiver to the same channel (01 or 02) by switching

the OFF/CH1/CH2 channel switch. Selected channel will be shown on the

top right corner of the LCD screen.

• Set both Transmitter and Receiver to the same pilot tone when using. By

selecting a Dip switch(ON/DIP/1/2/3/4) at the battery compartment for different

pilot tones to ensure privacy. There are 16 combinations of pilot tone for use

selection. (Please refer to the PILOT TONES COMBINATION TABLE)

NOTE:

It is important that with both units the switch settings are the same because if

this is not the case the transmitter and the receiver will not be able to connect to

one another.

Transmitter emission:

1. By using the SENSITIVITY knob you can turn in the sensitivity of the

transmitter individually, according to your wishes.

2. As soon as the transmitter transmits a signal the “Baby calling ” icon will be

ﬂ ashed on the LCD screen. During the entire transmission the LCD backlight

is activated.

3. If the transmitter hears hardly any noise, it automatically switches to the

energy saving mode. “Baby sleeping” icon shown on the LCD screen and the

LCD backlight will automatically be turned off.

Receiver reception:

1. By turning the volume knob from right side the receiver will be turned on. After

turning it on the LCD display is activated and indicates you that the unit is

ready for operation. The channel being used will be displayed in the top right

of the LCD screen. By turning the volume more you can adjust is as you wish.

2. If the unit receives a signal, the LCD backlight lights up automatically during

the entire transmission and the “Baby calling” icon ﬂ ashes.

3. A few seconds after the unit receives no more signals, the receiver is

automatically switched to energy saving mode. The “Baby sleeping” icon will

be shown and the LCD backlight will automatically turned off.

Set Up & Use

IMPORTANT! Test sound reception before use and whenever location of

transmitter is changed. (Refer to Testing Before First Time Usage)

1. Transmitter detects sound levels within a range of 1 to 2 meters (3 to 6.5 feet)

for NORM setting.

2. Place transmitter in the same room with child. Point microphone directly

toward child location, such as crib or playing area.

3. Set both Receiver and Transmitter to the same channel (01 or 02) and pilot

tone.

4. Push transmitter SENSITIVITY switch to a desired position.

5. Adjust different detecting sound level sensitivity by switching the SENSITIVITY

switch.

6. The receiver will go to energy saving mode and “Baby sleeping” icon shown

when it doesn‘t detect sound from the surrounding area.

7. Place receiver where you stay and hear it.

8. Set the receiver to the same channel and pilot tone with the transmitter by

switching OFF/CH1/CH2 switch and Dip switch.

9. Rotate VOLUME knob to adjust volume.

10.Turning off by slide the OFF/CH1/CH2 switch to “OFF” position.

Note:

• Position the Transmitter at least 1 meter away from the baby for transmission.

• Plug the adaptor into the nearest standard household electrical outlet.

20 21

Other functions

Pilot tone

Radio security and being free of interference for this

Baby-calling unit is signiﬁcantly improved by a signal

this is inaudible for you and which has been digitally

coded and tested in practice.

The coding causes the receiver to be turned on only

when noises (e.g. of a waking baby) are transmitted

from its own transmitter.

There are 16 different pilot tones for user selection

with the DIP-switch positioned in the battery comp-

artment individually according to your environment.

PILOT TONES COMBINATION TABLE

Pilot Tones Switch 1Switch 2Switch 3Switch 4

Code 1OnOnOnOn

Code 2OnOnOnOff

Code 3OnOnOff On

Code 4OnOnOff Off

Code 5OnOff On On

Code 6OnOff On Off

Code 7OnOff Off On

Code 8OnOff Off Off

Code 9Off On On On

Code 10 Off On On Off

Code 11 Off On Off On

Code 12 Off On Off Off

Code 13 Off Off On On

Code 14 Off Off On Off

Code 15 Off Off Off On

No Code Off Off Off Off

Remarks:

• OFF: No pilot tone is selected.

• If no pilot tone is selected for Receiver indicates an almighty code is selected.

In this status, the receiver can receive signal from transmitter in the same

channel whether any pilot tone of transmitter is selected.

Out of Range alarm and Range controls

If the receiver is out of the range of the transmitter, it will be signaled to you by a

ﬂ ashing visual range alarm icon shown on the receiver. In addition the range

alarm sound from Receiver will be heard continuously.

The out of range alarm will be still heard after the connection with the transmitter

is broken.

Furthermore, the visual and audible range alarm of the receiver is set off if :

• the connection between transmitter and receiver is broken, such as the

• transmitter is turned off.

• the transmitter is turned into a different channel to that of the receiver.

• the transmitter is tuned into a different pilot tone to that of the receiver.

• the transmitter or receiver is working with a charger with low batteries.

22 23

Backlight LCD display

When Power on / Out of range / Low battery level / Baby calling (i.e. a sound is

sent and received), the backlight of the transmitter as well as the receiver will

automatically turned on. Once no more signals are sent and received, the

backlight is automatically turned off.

Belt Clip

The transmitter and receiver can both be carried around using the belt clip

provided on the rear of each unit.

Trouble Shooting

Problems Solutions

1. No power • Unit is not turned on. Push the Unit OFF/CH1/

CH2 switch to CHI or CH2 position

• Check if the batteries are installed properly.

• Make sure the adaptor is connected to the Unit

properly if using the adaptor instead of

batteries.

• The Unit may be battery low, change for new

batteries.

2. Message not

transmitted

• Sound sensitivity level of Transmitter is too

low. Turn the Sound Sensitivity level proper

position.

• Units are out of range or lost connection. Move

Receiver closer to Transmitter.

• Ensure both units are in the same channel and

pilot tone.

3. Hearing static or rustle

from Receiver.

The Receiver is too near to the transmitter and

its volume is high . Increas e the distance

between the transmitter and receiver.

Reposition or replace batteries.

Technical Speciﬁcations

Power Supply Voltage:

Transmitter 3 AAA rechargeable batteries / alkaline batteries

& adaptor : AC 230V – DC 6V

Receiver 3 AAA rechargeable batteries / alkaline batteries

& adaptor : AC 230V – DC 6V

Channel : 2 Channels

Operation Frequency : CH1: 864.875 MHZ

CH2: 864.925 MHZ

Operating Range: up to 800 metre in ideal conditions

Registration and Safety Certiﬁcation/General Information

This device bears the CE symbol as speciﬁed by the provisions of Directive R & TTE

(1999/5/EC).

Hama GmbH & Co. KG hereby declares that this device is in compliance with the

basic requirements and other relevant guidelines and regulations of the 1999/5/EC

guideline. You will ﬁ nd the declaration of compliance and declaration of conformity

in the Internet at

http://www.hama.com

Page is loading ...

Hama 00092660, BC300, BC300 - 92660 Owner's manual

Related papers

Other documents