Konrow Link 5 Owner's manual

Page is loading ...

EN

For purchasing Link5 Smartphone. You will nd all the

informations regarding the use of this cellphone in this guide.

Giftbox content :

• 1 Smartphone

• 1 mains adaptor

• 1 USB cable

• 1 user guide

• 1 hands free kit

NOTE: The packaging materials, such as the adhesive tape,

plastic lm, string and labels, are not part of this product.

WARNING: For your safety, please do not remove the

screen’s protective lm, located under the antistatic

lm (with tab). It protects your screen against slight

scratches and provides optimum protection if the phone

is dropped.

Konrow accepts no responsibility for personal injury sustained

following removal of the protective lm by the consumer. Note

that this protective lm does not increase the robustness of the

product. For replacement of the protective lm, please consult

a specialist Smartphone dealer.

Konrow thanks you

1 - Front camera

2 - Rear camera & ash

3 - Volume

4 - ON/OFF button

5 - Jack

6 - Micro USB port

7 - Speakers

1. Description of the Smartphone.

EN

2. Inserting a SIM card 3. Inserting a MicroSD

The Link5 Smartphone is a mobile phone with dual SIM card,

which enables you to use two lines on the same Smartphone.

Your Link5 has two SIM ports for standard SIM (SIM1 and SIM2).

To insert the SIM card(s):

• Switch o the phone and remove the rear cover.

• Insert the SIM card correctly into the relevant card slot (

see gure below ).

• Then replace the battery and cover.

CAUTION: The 3G and 4G functions can only be used on one

SIM card.

It is possible to increase the internal memory of the Link5

device with a MicroSD card. (Maximum 32GB MicroSD card).

• Switch o the phone and remove the rear cover.

• Insert the memory card into the relevant slot.

• Then attach the rear cover.

CAUTION: Inserting or removing a SIM card or a MicroSD card

requires the Smartphone to be completely switched o.

4. Charging the battery

Charging the battery:

• To charge the battery, connect the USB cable (supplied) to

the USB port of your Smartphone and the other end to the

mains adaptor (supplied). Then connect the mains adaptor

to a power outlet.

• The battery charge icon illuminates during charging and

indicates the charge status.

• When the battery is fully charged, you can disconnect the

USB cable from the device then from the power outlet.

•

IMPORTANT:

• The Smartphone is only recharged via its USB port.

• Ensure your Smartphone is fully discharged before

charging it for the rst time.

• The battery must be charged for at least 5 to 8 hours when

rst charged.

Note: You can use the device when it is being charged. In this

case, the battery may take longer to charge fully

Safety information for charging the battery:

• To recharge the battery, only use the mains adaptor supplied

with your device. Do not use any other power supply or electrical

device. The power outlet to which the device is connected must

be near the equipment and must always be easily accessible.

• Always wait at least 5 seconds after switching o the device

before restarting it. Switching the device o and then back on

again immediately may damage the electrical circuits.

• Do not disassemble the battery. Do not dispose of batteries in

re or water. Do not charge the battery if the room temperature

exceeds 45°C.

EN

• For all repairs or to replace the battery, consult a qualied

technician.

• The lifetime of the battery depends largely on how you use

it. Do not expose the battery to temperatures less than 0°C or

greater than 60°C. Its performance may be altered.

• Signicant electromagnetic interference or electrostatic

discharge may cause malfunction or loss of data. If the

device is not working properly, restart the Smartphone or

unplug the mains adaptor from the power outlet then plug

it in again.

5. Switching the Smartphone on and o

To switch the Smartphone on, press the On/O button located

on the side of the Smartphone for 3 seconds.

If the Smartphone is switched on, press for less than a second

on the button to put the device into standby mode. Press it again

to leave standby mode.

To switch o the Smartphone, press the On/O button for 3

seconds until a menu appears, then touch the O button and

conrm.

6. Locking/unlocking SIM cards

Your Link5 is a dual SIM Smartphone. It enables you to phone

using two lines from the same device. There are two SIM card

slots.

• When you start up your phone, the latter invites you to

enter the PIN codes of your two SIM cards in succession.

(SIM1 then SIM 2)

• The «emergency call» function enables you to call an

emergency number without entering the PIN code.

EN

7. Locking/unlocking the screen

To unlock the screen:

• Press the power key on your phone.

• Hold and drag the unlock icon to the top to unlock the

device.

You can congure the screen lock by adding a password or

pattern to be replicated when unlocking your Smartphone.

CAUTION: Forgetting your screen lock password, PIN code or

pattern permanently blocks your Smartphone

If this is forgotten or lost, the product warranty will not cover

such an oversight. Even a “reset”

cannot solve the problem. As a precaution, take a note of your

password or pattern.

PASSWORD: _________________

To lock your device, simply press the on/o button.

8. Making a call

NOTE: It is impossible to make or receive a call on the two SIM

cards at the same time.

For example, if you are on a call on the SIM 1 line, those

trying to contact you on SIM 2 will automatically be diverted

to voicemail.

• Tap the icon on the main menu or the home screen

to dial the number of your choice.

• Tap the operators icon to call with SIM 1 or SIM 2.

• Press the +/- buttons to adjust the call volume.

• When you want to end a call, press the icon .

• When a call is received, slide your nger over the icon .

• When you want to end a call, press the icon .

9. Receiving a call

EN

Bluetooth deactivated

Bluetooth activated

10. Activate/Deactivate the Bluetooth

connection

Note: To limit your exposure to EMF we recommend you to

deactivate Bluetooth when it is not any more used.

You can activate Bluetooth by the shortcuts of basic regulation

of the notication bar or in the parameters of the Smartphone.

• Click on the activation button and scroll to the right.

• When the Bluetooth is activated you will see the icon on

the notication bar.

Note: To limit your exposure to EMF we recommend you to

deactivate Wi Fi when it is not any more used.

You can activate Wi Fi by the shortcuts of basic regulation of

the notication bar or in the parameters of the Smartphone.

• Click on the activation button and scroll to the right.

• When the Wi-Fi is activated you will see the icon on the

notication bar.

11. Activate/Deactivate the Wi-Fi

connection

Wi-Fi deactivated

Wi-Fi activated

EN

12. Download an application

NOTE: Most Wi-Fi networks are locked with a password

(WEP or WPA2 PSK key). To connect to a locked Wi-Fi

network, click on it and enter the password for your

network in the dialogue box which is displayed on the

screen.

The WEP or WPA2 PSK key for a Wi-Fi network is generally

noted on a label located on the back of your internet

modem.

Note: Restart your Smartphone if necessary.

Your Link5 Smartphone is supplied with the Google™ on-

line store enabling you to download applications such as

utilities and games.

To access these to the store, go to the application page using

the button located on the home page and tap the Play Store

icon.

Google, Google Play and Android are trademarks of Google

Inc. registered

Note: The availability of access to Google Play™ Store depends

on your phone operator and the country in which you

are located. Access to the on-line store requires an account to

be created.

NOTE: Konrow shall under no conditions be responsible

for the content on the on-line store. The product warranty

will not cover any malfunction due to an application from

on-line stores.

13. Reset

If you want to reset your smartphone, you can do a reset of

data from the operating system Android™.

CAUTION: A reset data erase all your personal data, all

contacts in your phone and the applications you have installed.

That is why we recommend that you make a backup of your

data before starting the procedure. However the information

stored on the external memory card will not be erased.

To do a reset of the data:

• In Settings, click “Factory data reset” and “Factory data

reset”.

• Click “Reset phone” and conrm “Erase everything”.

The smartphone will turn o and on rebooting the system

will reset.

NOTE : If you have any problem with your device, please try to

reset the system before sending it back.

Page is loading ...

Listening safety

• Before using the pedestrian kit, check that the volume is

not set to maximum to prevent hearing loss.

• The high volume settings are intended for individuals with

reduced hearing capacity and not for those with normal

hearing.

• Do not use the pedestrian kit while driving.

• Adjust the volume so that you can hear the sounds around

you.

• To prevent possible hearing damage, do not listen at high

volume levels for long periods.

• Listening to a portable audio player at high volumes can

damage your hearing and

• lead to hearing impairment (deafness, ringing ears,

tinnitus and hyperacusis).

• In order to prevent these risks it is recommended not to

use the device at full volume; use must not exceed one

hour per day.

• Do not use pre-amplied or amplied models of

headphones or pedestrian kit (i.e. with individual volume

control and/or self-powered by batteries), as they do not

ensure adherence to the maximum volume.

This product complies with the EN 60950-1:2006/A12:2011

standard «Information technology equipment - Safety - Part 1:

General requirements» in accordance with the order of 25 July

2013 implementing Article L. 5232-1 of the French public health

code concerning portable audio players.

Electromagnetic waves safety information

(SAR)

Your Link5 Smartphone is designed to not exceed the radio

wave limits recommended by the European authorities. These

limits include safety margins to ensure the protection of all

persons regardless of their age or health.

The SAR (specic absorption rate) of mobile phones quanties

EN

the maximum level of exposure of the user to electromagnetic

waves, for aural use. French legislation stipulates that the SAR

must not exceed 2 W/kg averaged over 10g of tissue.

The value of the SAR is determined on the basis of the highest

level of radio frequencies emitted during laboratory tests.

The actual value of the SAR during use of the phone is lower

than this level.

The value of the SAR of the phone can vary according to the

following factors: how far/close the phone is to a relay antenna,

use of accessories and others.

NOTE: The SAR value may vary, depending on national reporting

and testing requirements and the network band.

NOTE:

• Do not use your Smartphone in certain locations such as

aircraft, hospitals, service stations and professional garages

or while driving a vehicle. The electromagnetic waves from

the Smartphone can disrupt the performance of electronic

devices used in these locations.

• We recommend that you switch o your phone or switch it

to ight mode in these locations to avoid interference.

• If you use an electronic implant (pacemakers, insulin

pumps, neurostimulators, etc.), please keep a distance of

15cm between the Smartphone and your electronic implant.

• When using a hands-free kit, pregnant women should keep

the phone away from their abdomen and teenagers should

keep the phone away from their lower abdomen.

Advice to reduce the level of exposure to radiation:

• Please use your Smartphone where reception is good to

reduce the quantity of radiation received (avoid using in an

underground car park or when travelling (train or car)).

• A reception icon indicates the quality of reception on your

phone. A 4-bar display means that reception is good.

• Use of a hands-free kit also allows the level of exposure to be reduced.

Safety and care information

• Read these instructions carefully. Keep these instructions.

• Follow all these instructions.

• Heed the warnings.

• Clean only with a soft cloth (dry or slightly damp).

• Do not attempt to disassemble the device; it would no longer be

covered by the warranty.

• Do not bring sharp objects directly into contact with the surface

and do not spray any cleaning product directly onto the screen.

• Do not exert excessive pressure on the screen and do not put

objects on it. This could damage the screen.

• Use the spare parts specied by the manufacturer.

• After any service or repair carried out on this product, ask the

technician to perform a safety check.

• Use only the spare parts/accessories specied by the manufacturer.

• Refer to a qualied person for any repairs. Repair is required if the

device is damaged in some manner or other, if the power cord or

plug is damaged, if liquid has been spilled or objects have fallen on

the device, or if the device has been exposed to rain or moisture,

or has been dropped.

• Do not expose the device to direct sunlight or other source of

extreme heat or cold.

• Respect the privacy of others when using your Smartphone.

• Keep the device away from all metal objects (coins, keys, etc.).

• Do not leave near a magnetic eld as this could cause data to be

lost or could damage the device.

• Do not drop the device.

• Do not expose the device to shocks, friction or impact.

• In order to prevent data loss, remember to make a (computer or

paper) back-up of information saved on the device.

• To prevent interference, do not use the device near other

electronic devices, a pacemaker or medical equipment.

• Operating temperature: 0°C and 40°C.

NOTE: In order to reduce any risk of re or electric shock :

• Do not expose this device to rain or moisture.

• Do not expose the product to water droplets or to splashes and do

not place any object lled with liquid, such as a vase, on the device.

• Do not use the product near ammable or explosive materials.

• The power plug is used to disconnect the device and must always

be easily accessible.

• In order to completely disconnect the device from the electricity

supply, the power plug must be disconnected from the power outlet.

• Do not attempt to override the safety features of the polarised

plug or the earth connection. A polarised plug has two pins, one of

which is wider than the other. A plug with an earth connection has

two at pins and a third round pin for the earth connection. The

widest pin and the third pin constitute the important safety features

designed to protect you. If you cannot manage to fully insert the plug

into the wall outlet, contact your electrician to replace the obsolete

wall socket.

• Disconnect this device during electrical storms or when not in use

for an extended period.

• Switch o the device in places presenting risk of explosion and

when travelling by plane.

• Do not touch the power cord with wet hands and do not pull on the

charger to disconnect it.

• The power cord must be placed so that it will not be stepped on or

crushed particularly at the outlet, where it is plugged in or where it

is connected to the device.

• Do not overload the power outlet. Use the power supply only

as indicated. Do not install this device near heat sources such as

electric hobs, cookers or others (including ampliers).

EN

Warning on using the phone while driving

In France, in accordance with Article R412-6-1 of the French

highway code, drivers are not permitted to use hand-held

phones whilst the vehicle is moving.

The penalty for non-compliance with this article is a ne and

point penalty on your driving licence.

The use of a hands-free kit is permitted. However, Article

R412-6 of the French highway code provides for a ne without

licence penalty points if the driver is not in a position to carry

out required manœuvres comfortably and without delay when

using his hands-free kit whilst driving.

NOTE: this legislation applies only in France. During trips

abroad, please refer to the legislation in place in

your country of origin before travelling.

Epilepsy warning

Please read before using a video game or allowing your

children to use one.

Some people are susceptible to epileptic seizures or loss of

consciousness when exposed to certain ashing lights or light

patterns in everyday life. Such people may have a seizure while

watching television images or playing certain video games.

This may happen even if the person has no medical history

of epilepsy or has never had any epileptic seizures. If you

or anyone in your family has ever had symptoms related to

epilepsy (seizures or loss of consciousness) when exposed to

ashing lights, consult your doctor prior to playing. We advise

that parents should monitor the use of video games by their

children. If you or your child has the following symptoms

while playing a video game, discontinue use IMMEDIATELY

and consult your doctor: dizziness, blurred vision, eye or

muscle twitches, loss of consciousness, disorientation, any

involuntary movement or convulsion.

Precautions to take during use of any video game:

• Do not sit too close to the screen. Sit a good distance away

from the television screen, as far away as the length of the

cable allows.

• Preferably play the game on a small television screen.

Avoid playing if you are tired or have not had much sleep.

• Make sure that the room in which you are playing is well

lit.

• Rest for ten to fteen minutes per hour while playing a

video game.

Google, Google Play and Android are trademarks of Google Inc.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

registered trademarks or trademarks of Adobe Systems

Incorporated in the United States and/or other countries.

THIS PRODUCT IS LICENSED UNDER THE AVC PATENT

PORTFOLIO LICENSE FOR THE PERSONAL AND NON-

COMMERCIAL USE OF A CONSUMER TO

(i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD

(“AVC VIDEO”) AND/OR

(ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER

ENGAGED IN A PERSONAL AND NON- COMMERCIAL ACTIVITY

AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED

TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL

BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION

MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE http://mpegla.

com.

Facebook, the Facebook logo, and the F logo are trademarks or

registered trademarks of Facebook, Inc.

Foursquare is the registered trademark of Foursquare

Labs, Inc. This software is partially based on the work of the

Independent JPEG Group.

The MPEG Layer-3 audio encoding technology and patents are

licensed by Fraunhofer IIS and Thomson.

THIS PRODUCT IS LICENSED UNDER THE MPEG4 PATENT

PORTFOLIO LICENSE FOR THE PERSONAL AND NON-

COMMERCIAL USE OF A CONSUMER TO

(i) ENCODE VIDEO IN COMPLIANCE WITH THE MPEG4

STANDARD (“MPEG4 VIDEO”) AND/O R

(ii) DECODE MPEG4 VIDEOS THAT WAS ENCODED BY A

CONSUMER ENGAGED

IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/

OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO

PROVIDE MPEG4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE

IMPLIED FOR ANY OTHER

USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM

MPEG LA, L.L.C. SEE http://mpegla.com.

SD, SDHC, microSD and the microSDHC logos are trademarks

of SD-3C, LLC.

The Twitter name, logo, Twitter T, Tweet, and Twitter bird

are trademarks of Twitter, Inc. in the United States and other

countries.

THIS PRODUCT IS LICENSED UNDER THE VC-1 PATENT

PORTFOLIO LICENSE FOR THE PERSONAL AND NON-

COMMERCIAL USE OF A CONSUMER TO

(i) ENCODE VIDEO IN COMPLIANCE WITH THE VC-1 STANDARD

(“VC-1 VIDEO”) AND/OR

(ii) DECODE VC-1 VIDEO THAT WAS ENCODED BY A CONSUMER

ENGAGED IN A PERSONAL AND NON- COMMERCIAL ACTIVITY

EN

AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED

TO PROVIDE VC-1 VIDEO.

NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY

OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED

FROM MPEG LA, L.L.C.

SEE http://mpegla.com.

Wi-Fi, the Wi-Fi CERTIFIED logo, WPA, WPA2 and Wi-Fi Protected

Setup are trademarks or registered trademarks of Wi-Fi

Alliance.

Windows Media is either a registered trademark or trademark

of Microsoft Corporation in the United States and/or other

countries.

All other names of systems, products and services are

trademarks or registered trademarks of their respective

owners. The symbols ((TM)) or (R) are not used in this guide.

Recycling

The symbol shown here and on the product

means that the product is classed as Electrical or

Electronic Equipment and should not be disposed

with other household or commercial waste at the

end of its working life.

The Waste Electrical and Electronic Equipment

(WEEE) Directive (2012/19/EU) has been put

in place to recycle products using best available recovery

and recycling techniques to minimise the impact on the

environment, treat any hazardous substances and avoid the

increasing landll.

Product disposal instructions for residential users:

If you no longer use the device, remove and dispose of the

battery, as well as the device, in compliance with the local

recycling procedures. For more information please contact

your local authority or the retailer where the product was

purchased.

Product disposal instructions for business users:

Business users should contact their suppliers and check the

terms and conditions of the purchase contract and ensure

that this product is not mixed with other commercial waste

for disposal.

If you encounter any problems:

Please contact the after sales service on the contact page of

our website: www.konrow.com

Made in PRC

2015 Konrow.

If unresolved problem, contact your retailer.

The Konrow supplier warranty is valid for normal use of the

device as dened in the instructions. This warranty excludes

damage caused by external circumstances.

Specically, the warranty does not apply if the device is

damaged as a result of a bump or drop, an operating error,

a connection that does not comply with these instructions,

lightning, a surge, or inadequate protection against heat,

humidity, or freezing temperatures.

The warranty is applicable only in metropolitan France.

• The warranty does not cover user manuals or applications,

settings, content or data of any kind.

• The warranty does not cover normal usury of the product.

(Screens, batteries and camera)

• The warranty does not cover damage to the product due

to misuse, including in particular those caused by objects,

a pressure drop.

• The warranty does not cover any use of the label with the

precautions outlined in the manual.

• The warranty does not cover defects caused to the product

with another product connected or used with an accessory

or software not provided by Konrow.

• The warranty does not cover any damage to the battery.

• The warranty does not cover the product or its

accessories if it has been disassembled or modied in

any way.

• The warranty does not cover any unidentiable product by

serial number or (s) number (s) IMEI. If its elements have

been removed, altered or defaced, the warranty does not

apply.

• The warranty does not cover damage done to the

product caused by exposure to moisture, conditions that

extreme heat or cold, corrosion, oxidation, with any liquid

whatsoever

• The warranty does not cover any damage to (s) player (s)

or SIM MicroSD reader.

• The legal warranty for hidden defects applies in compliance

with Articles 1641 et seq. of the French Civil Code.

Page is loading ...

Declaration of conformity

We, Konrow - 27 boulevard d’Arras - 13004 Marseille - FRANCE,

hereby declare that the Konrow Link5 Smartphone complies with the essential requirements of the Directive R&TTE 1999/05/EC

applicable to the following European standards:

Safety EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013; EN50332-1:2013; Health EN 50360:2001+A1:2012; EN 62209-1:

2006; IEC 62209-1:2005; EN 62209-2-2010; IEC 62209-2 :2010; EN50566:2013; EN 62479:2010; EMC EN 301 489-1 V1.9.2; EN 301

489-3 V1.6.1; EN 301 489-7 V1.3.1; EN 301 489-17 V2.2.1; EN 301 489-24 V1.5.1; EN 55022:2010/AC:2011; EN 61000-3-2:2014;EN

61000-3-3:2013; EN 55024:2010; Radio EN 301 511 V9.0.2; EN 300 328 V1.9.1; EN 301 908-1 V7.1.1; EN 301 908-2 V6.2.1; EN 300 440-1

V1.6.1; EN 300 440-2 V1.4.1; EN 301 908-1 V7.1.1; EN 301 908-13 V6.2.1

The procedure of Declaration of conformity, set out in Article 10.5 of Directive 1999/5/EC was conducted under the supervision of

the following organisation:

PHOENIX TESTLAB Königswinkel

10, D-32825 Blomberg, Germany.

Phone: +49(0)5235-9500-24 Fax: +49(0)5235-9500-28

The full text of the device’s Declaration of conformity is available on written request to the following address :

HEM - 27 boulevard d’Arras - 13004 Marseille - FRANCE

27/05/2016 Maurice Haddad / CEO

Date (Name and signature of the duly authorised person)

Specic Absorption Rate: EGMS900 / DCS1800

SAR (Head) = 0.162 W/Kg

SAR (Body) = 0.438 W/Kg

Page is loading ...

Konrow Link 5 Owner's manual

Related papers

Other documents