MQ Power DCA70USI Operating instructions

PARTS AND OPERATION MANUAL

OPERATION AND PARTS MANUAL

Revision #0 (01/04/06)

THIS MANUAL MUST ACCOMPANY

THE EQUIPMENT AT ALL TIMES.

ULTRA-SILENT

TM

SERIES

MODEL DCA-70USI

60 Hz GENERATOR

PARTS LIST NO. M2900000314

PAGE 2 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06) — PAGE 3

1

MQ Power Inc, Ultra-Silent series, and the MQ Power logo are registered trademarks of Multiquip Inc. and may not be used,

reproduced, or altered without written permission. All other trademarks are the property of thier respective owners and used with

permission.

This manual

MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and

should remain with the unit if resold.

The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are

based on the

DCA-70USI (60 Hz) Ultra Silent Generator

. Multiquip Inc. reserves the right to discontinue or change specifications,

design or the information published in this publication at any time without notice and without incurring any obligations.

To find the latest revision of this

publication, visit our website at:

www.mqpower.com

HERE'S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL

NUMBER

ON-HAND

WHEN CALLING

MQ POWER CORPORATE OFFICE

18910 Wilmington Ave. 800-421-1244

Carson, CA 90746

FAX:

310-632-2656

Email: mqpower@multiquip.com

Internet: www.mqpower.com

PARTS DEPARTMENT

800-427-1244

FAX:

800-672-7877

310-537-3700

FAX:

310-637-3284

SERVICE DEPARTMENT

800-835-2551

FAX:

310-638-8046

310-537-3700

TECHNICAL ASSISTANCE

800-835-2551

FAX:

310-638-8046

WARRANTY DEPARTMENT

800-835-2551,

EXT.

279

FAX:

310-638-8046

310-537-3700,

EXT.

279

PAGE 4 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

TABLE OF CONTENTS

Specification and part

number are subject to

change without notice.

NOTE

MQ POWER DCA-70USI(60HZ)MQ POWER DCA-70USI(60HZ)

MQ POWER DCA-70USI(60HZ)

ULUL

UL

TRA-SILENT GENERATRA-SILENT GENERA

TRA-SILENT GENERA

TORTOR

TOR

California Proposition 65 Warning ..................................... 2

Here's How To Get Help .................................................... 3

Table Of Contents ............................................................. 4

Parts Ordering Procedures ............................................... 5

Specifications ................................................................... 6

Dimensions (Top, Side, Front) ........................................... 7

Safety Message Alert Symbols .................................... 8-9

Rules for Safe Operation ........................................... 10-13

Generator Decals....................................................... 14-15

Installation ................................................................. 16-17

General Information ........................................................ 18

Major Components ......................................................... 19

Generator Control Panel ................................................. 21

Engine Operating Panel ............................................. 22-23

Output Terminal Panel Familiarization ........................ 24-26

Load Application ............................................................. 27

Generator Outputs .......................................................... 28

Gauge Reading ............................................................... 29

Output Terminal Panel Connections ........................... 30-31

Pre-Setup .................................................................. 32-35

Generator Start-up Procedure (Manual) ..................... 36-37

Generator Start-up Procedure (Auto Mode) .................... 38

Generator Shut-Down Procedure .................................... 38

Maintenance (Engine) ................................................ 39-40

Maintenance (Trailer) ................................................. 41-44

Trailer Wiring Diagram ..................................................... 45

Generator Wiring Diagram ............................................... 46

Engine Wiring Diagram ................................................... 47

Generator Troubleshooting .............................................. 48

Engine Controller Troubleshooting ................................... 49

Explanation of Code in Remarks Column ....................... 50

Suggested Spare Parts .................................................. 51

Generator Assembly .................................................. 52-53

Control Box Assembly ............................................... 54-57

Engine and Radiator Assembly ................................. 58-61

Output Terminal Assembly ......................................... 62-63

Battery Assembly ...................................................... 64-65

Muffler Assembly ...................................................... 66-67

Fuel Tank Assembly .................................................. 68-69

Enclosure #1 Assembly ............................................ 70-73

Enclosure #2 Assembly ............................................ 74-75

Rubber Seals Assembly ............................................ 76-77

Nameplate and Decals .............................................. 78-79

Terms and Condition of Sale — Parts ............................ 80

ISUZU FF- 4BG1T ENGINEISUZU FF- 4BG1T ENGINE

ISUZU FF- 4BG1T ENGINE

DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06) — PAGE 5

1

MQPOWER

A Division of Multiquip Inc.

POST OFFICE BOX 6254

CARSON, CA 90749

310-537-3700 • 800-421-1244

FAX: 310-632-2656

E-MAIL: [email protected]

INTERNET: www.mqpower.com

When ordering parts,

please supply the following information:

❒❒

❒ Dealer account number

❒❒

❒ Dealer name and address

❒❒

❒ Shipping address (if different than billing address)

❒❒

❒ Return fax number

❒❒

❒ Applicable model number

❒❒

❒ Quantity, part number and description of each part

❒❒

❒ Specify preferred method of shipment:

✓ FedEx or UPS Ground

✓ FedEx or UPS Second Day or Third Day

✓ FedEx or UPS Next Day

✓ Federal Express Priority One

✓ DHL

✓ Tr u ck

Note: Unless otherwise indicated by customer, all

orders are treated as “Standard Orders”, and will

ship within 24 hours. We will make every effort to

ship “Air Shipments” the same day that the order is

received, if prior to 2PM west coast time. “Stock

Orders” must be so noted on fax or web forms.

Extra Discounts!

All parts orders which include complete part numbers and

are received by our automated web parts order system, or

by fax qualify for the following extra discounts:

Ordered Standard Stock orders

via orders ($750 list and above)

Fax 3% 10%

Web 5% 10%

Special freight allowances

when you order 10 or more

line items via Web or Fax!**

FedEx Ground Service

at no charge for freight

No other allowances on freight shipped by any other carrier.

**Common nuts, bolts and washers (all items under $1.00

list price) do not count towards the 10+ line items.

Place Your Parts Order Via Web or Fax

For Even More Savings!

(Domestic USA Dealers Only)

NOTE: DISCOUNTS ARE SUBJECT TO CHANGE

Here’s how to get help...

Please have the model and serial number

on hand when calling.

MQ POWER CORPORATE OFFICE

18910 Wilmington Ave. 800-421-1244

Carson, CA 90746

FAX:

310-632-2656

Email: mqpower@multiquip.com

Internet: www.mqpower.com

PARTS DEPARTMENT

800-427-1244

FAX:

800-672-7877

310-537-3700

FAX:

310-637-3284

SERVICE DEPARTMENT

800-835-2551

FAX:

310-638-8046

310-537-3700

TECHNICAL ASSISTANCE

800-835-2551

FAX:

310-638-8046

WARRANTY DEPARTMENT

800-835-2551,

EXT.

279

FAX:

310-638-8046

310-537-3700,

EXT.

279

Direct TOLL-FREE access

to our Parts Department:

Toll-free nationwide — 800-427-1244

Toll-free FAX — 800-6-PARTS-7

(800/672-7877)

PARTS ORDERING PROCEDURES

PAGE 6 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

DCA-70USI (60 Hz) — SPECIFICATIONS

snoitacificepSrotareneG.1elbaT

ledoMISU07-ACD

epyT

,detalitnevfles,dleifgnivloveR

rotarenegsuonorhcnysepytdetcetorpnepo

noitcennoCerutamr

AlartueNhtiwratSgaZgiZ

esahP

3elgniS

tuptuOybdnatS

)WK8.85(AVK5.37WK24

tuptuOemirP

)WK65(AVK07wK04

egatloV

V084roV

042021/042

ycneuqerF

zH06

deepS

mpr0081

rotcaFrewoP

8.01

rewoPCA.xuA

zH06,esahPelgniS

egatloV

V021

tuptuO

)2xWK4.2(

WK8.4

snoitacificepSenignE.2elbaT

ledoM

T1GB4-FFUZUSI

epyT

degrahc-obrut,noitcejnitcerid,delooc-retaw,elcyc4

srednilyCfo.oN

srednilyc4

ekortS

xeroB

)mm521xmm501(.ni29.4x.ni31.4

tnemecalpsiD

)cc923,4(.ni.uc462

gnitratS

CDV21cirtcelE

yticapaCtnalooC

)s

retil4.41(.lag08.3

yticapaCliOebuL

)sretil2.31(.lag94.3

epyTleuF

leuFleseiD2#

yticapaCknaTleuF

)sretil093(.

lag301

noitpmusnoCleuF

tarh/)L0.31(.lag13.4 daollluf

yrettaB

1x)A007FOACC(72

DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06) — PAGE 7

1

DCA-70USI (60 Hz) — DIMENSIONS (TOP, SIDE AND FRONT)

Figure 1. Dimensions

SNOISNEMID.3ELBAT

ecnerefeR

retteL

).mm(.ninoisnemiDretteLecnerefeR).mm(.ninoisnemiD

A).mm097(.ni01.13F ).mm076,2(.ni11.501

B).mm6

67(.ni51.03G ).mm537,1(.ni03.86

C).mm667(.ni51.03H ).mm059(.ni04.73

D).mm667(.ni51.03

E).mm667(.ni51.03

PAGE 8 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

Before using this generator, ensure that the operating

individual has read and understands all instructions in

this manual.

Safety precautions should be followed at all times when

operating this equipment. Failure to read and understand the

Safety Messages and Operating Instructions could result in

injury to yourself and others.

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

HAZARD SYMBOLS

Potential hazards associated with the operation of this

equipment will be referenced with "

Hazard Symbols

" which

appear throughout this manual, and will be referenced in

conjunction with Safety "

Message Alert Symbols

".

NOTE

DCA- 70USI (60 Hz) — SAFETY MESSAGE ALERT SYMBOLS

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you

about potential hazards that could injure you or others. The

Safety Messages specifically address the level of exposure

to the operator, and are preceded by one of three words:

DANGER, WARNING, or CAUTION.

You WILL be KILLED or SERIOUSLY injured if you

do not follow directions.

You COULD be KILLED or SERIOUSLY injured if

you do not follow directions.

You CAN be injured if you do not follow directions

Gasoline engine exhaust gases contain

poisonous carbon monoxide. This gas is

colorless and odorless, and can cause

DEATH

if inhaled. NEVER operate this

equipment in a confined area or enclosed structure that

does not provide ample free flow air.

Gasoline

is extremely flammable, and

its vapors can cause an explosion if

ignited. DO NOT start the engine near

spilled fuel or combustible fluids.

DO NOT fill the fuel tank while the engine

is running or hot.

DO NOT overfill tank, since spilled fuel could ignite if it

comes into contact with hot engine parts or sparks from

the ignition system. Store fuel in approved containers, in

well-ventilated areas and away from sparks and flames.

NEVER use fuel as a cleaning agent.

Engine components can generate extreme

heat. To prevent burns, DO NOT touch these

areas while the engine is running or

immediately after operations. NEVER

operate the engine with heat shields or heat

guards removed.

WARNING

DANGER

CAUTION

WARNING - LETHAL EXHAUST GASES

WARNING - BURN HAZARDS

WARNING - EXPLOSIVE FUEL

During operation of this generator, there

exists the possibility of

electrocution,

electrical shock or burn,

which can cause

severe bodily harm

or even

DEATH!

DANGER - ELECTROCUTION HAZARDS

This

Operation and Parts

Manual has been developed to

provide complete instructions

for the safe and efficient

operation of the MQ Power

Model DCA-70USI(60Hz)

UltraSilent™ Generator.

DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06) — PAGE 9

1

DCA- 70USI (60 Hz) — SAFETY MESSAGE ALERT SYMBOLS

ALWAYS place the Engine ON/OFF

switch in the OFF position and remove

the ignition key when the pump is not in

use.

ALWAYS wear approved

respiratory

protection.

ALWAYS wear approved

eye

and

hearing

protection.

Other important messages are provided throughout this

manual to help prevent damage to your generator, other

property, or the surrounding environment.

This generator, other property, or

the surrounding environment

could be damaged if you do not

follow instructions.

NOTE

NEVER tamper with the factory settings

of the engine governor or settings.

Personal injury and damage to the engine

or equipment can result if operating in

speed ranges above maximum allowable.

CAUTION - OVER-SPEED CONDITIONS

CAUTION - ACCIDENTAL STARTING

CAUTION - RESPIRATORY HAZARDS

CAUTION - SIGHT AND HEARING HAZARDS

CAUTION - EQUIPMENT DAMAGE MESSAGES

NEVER operate equipment with covers,

or guards removed. Keep

fingers

,

hands

,

hair

and clothing away from all moving

parts to prevent injury.

WARNING - ROTATING PARTS

PAGE 10 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

DCA-70USI (60 Hz) — RULES FOR SAFE OPERATION

The following safety guidelines should always be used when

operating the

DCA-70USI (60 Hz) Ultra Silent™ Generator.

General Safety:

■

DO NOT operate or service this

equipment before reading this entire

manual.

The operator MUST BE familiar with proper safety

precautions and operations techniques before using

generator.

■

This equipment should not be operated by persons under

18 years of age.

■

NEVER operate this equipment without proper protective

clothing, shatterproof glasses, steel-toed boots and other

protective devices required by the job.

■

NEVER operate this equipment when not

feeling well due to fatigue, illness or taking

medicine.

■

NEVER operate this equipment under the influence or

drugs or alcohol.

■

NEVER use accessories or attachments, which are not

recommended by MQ Power for this equipment. Damage

to the equipment and/or injury to user may result.

■

Manufacturer does not assume responsibility for any

accident due to equipment modifications. Unauthorized

equipment modification will void all warranties.

■

Whenever necessary, replace nameplate, operation and

safety decals when they become difficult read.

Failure to follow instructions in this manual may lead to

serious injury

or even

DEATH

! This equipment is to be

operated by trained and qualified personnel only! This

equipment is for industrial use only.

DANGER - READ THIS MANUAL!

■

ALWAYS check the machine for loosened threads or bolts

before starting.

■

NEVER operate the generator in an explosive atmosphere

or near combustible materials. An explosion or fire could

result causing severe

bodily harm or even death.

■

NEVER touch the hot exhaust manifold, muffler

or cylinder. Allow these parts to cool before

servicing engine or generator.

■

High Temperatures – Allow the engine

to cool before performing service and

maintenance functions. Contact with

hot!

components can cause serious

burns.

■

The engine of this generator requires an adequate free

flow of cooling air.

NEVER

operate the generator in any

enclosed or narrow area where free flow of the air is

restricted. If the air flow is

restricted it will cause serious

damage to the generator or

engine and may cause injury

to people. The generator

engine gives off DEADLY

carbon monoxide gas.

■

DO NOT place hands or fingers inside generator engine

compartment when engine is running.

■

NEVER run engine without air filter. Severe engine damage

may occur.

■

DO NOT leave the generator running in the

manual mode

unattended.

■

Refer to the

ISUZU Engine Owner's Manual

for engine

technical questions or information.

■

ALWAYS store equipment properly when it is not being

used. Equipment should be stored in a clean, dry location

out of the reach of children.

DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06) — PAGE 11

1

DCA-70USI (60 Hz) — RULES FOR SAFE OPERATION

POWER

CORD

(POWER ON)

WET

HANDS

During operation of this generator, there

exists the possibility of

electrocution,

electrical shock or burn,

which can cause

severe bodily harm

or even

DEATH!

To avoid these hazards:

NEVER use damaged or worn cables when connecting

equipment to the generator. Make sure power connecting

cables are securely connected to the generator’s output

terminals, insufficient tightening of the terminal connections

may cause damage to the generator

and electrical shock.

NEVER grab or touch a live power

cord with wet hands.

NEVER touch output terminals

during operation. This is extremely

dangerous. ALWAYS stop the

machine and place the circuit

breaker in the OFF position when

contact with the output terminals is

required.

Backfeed to a utility system can

cause

electrocution

and or property

damage. DO NOT connect to any

building's electrical system except

through an approved device or after

building main switch is opened.

ALWAYS have a licensed electrician

perform the installation

DANGER - ELECTROCUTION HAZARDS

Generator Grounding

To guard against electrical shock and possible damage to

the equipment, it is important to provide a good EARTH

ground.

Article 250 (Grounding) of the

National Electrical Code

(NEC) provides guide lines for proper grounding and specifies

that the cable ground shall be connected to the grounding

system of the building as close to the point of cable entry

as practical.

The following safety recommendations should also be

followed:

■

ALWAYS make sure generator is properly grounded.

■

NEVER use gas piping as an electrical ground.

■

ALWAYS make sure that electrical circuits are properly

grounded

per the

National Electrical Code

(NEC) and

local codes before operating generator. Severe

injury

or

DEATH!

by electrocution can result from operating an

ungrounded generator.

■

ALWAYS be sure to use the ground terminal (green wire)

when connecting a load to the U,V, and W output

terminal lugs.

Electrical Safety

■

ALWAYS have a qualified electrician perform the

generator wiring installation.

■

ALWAYS make sure generator installation is accordance

with the

National Electrical Code

(NEC) and local codes

before operating generator.

■

NEVER use a defective or frayed power cable. Check

the cable for cuts in the insulation.

■

NEVER use a extension cord that is frayed or damaged

where the insulation has been cut.

■

ALWAYS make certain that proper extension cord has

been selected for the job. See Table 6.

■

NEVER power cables or cords

lay in wate

r.

■

NEVER

stand in water

while AC power from the generator

is being transfer to a load.

PAGE 12 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

DCA-70USI (60 Hz) — RULES FOR SAFE OPERATION

Battery Safety

Use the following guidelines when handling the battery:

■

The battery contains acids that can

cause injury to the eyes and skin. To

avoid eye irritation,

always

wear safety

glasses.

■

Use well insulated gloves when picking up the battery.

Maintenance Safety

■

The electrical voltage required to operate the generator

can cause severe injury or even death through physical

contact with live circuits.

Turn all circuit breakers OFF

before performing maintenance on the generator.

■

NEVER lubricate components or attempt service on a

running machine.

■

ALWAYS disconnect the

NEGATIVE battery terminal

before performing service on the generator.

■

Follow all Battery Safety Guidelines listed in this manual

when handleing or servicing the generator.

■

ALWAYS allow the machine a proper amount of time to

cool before servicing.

■

Keep the machinery in proper running condition.

■

Fix damage to the machine immediately and always

replace broken parts.

■

ALWAYS service air cleaner frequently to prevent engine

malfunction.

To prevent burns, DO NOT touch or open any of the below

mentioned components while the engine is

running or immediately after operations.

Always allow sufficient time for the engine

and generator to cool before performing

maintenance.

■

Radiator Cap - Removing the radiator cap while the

engine is hot will result in high pressurized, boiling water

to gush out of the radiator, causing severe scalding to

any persons in the general area of the generator.

■

Coolant Drain Plug - Removing the coolant drain plug

while the engine is hot will result in hot coolant gushing

out of the coolant drain plug, therefore causing severe

scalding to any persons in the general area of the

generator.

■

Engine Oil Drain Plug - Removing the engine oil drain

plug while the engine is hot will result in hot oil gushing

out of the oil drain plug, therefore causing severe

scalding to any persons in the general area of the

generator.

WARNING - BURN HAZARDS

■■

■

ALWAYS keep the battery charged. If the battery is not

charged a buildup of combustible gas will occur.

■■

■

ALWAYS keep battery charging and cables in good working

condition. Repair or replace all worn cables.

■■

■

ALWAYS recharge the battery in an vented air

environment, to avoid risk of a dangerous concentration

of combustible gases.

■■

■

In case the battery liquid (dilute sulfuric acid) comes in

contact with

clothing or skin

, rinse skin or clothing

immediately with plenty of water.

■■

■

In case the battery liquid (dilute sulfuric acid) comes in

contact with your

EYES

, rinse eyes immediately with

plenty of water and contact the nearest doctor or hospital

to seek medical attention.

The risk of an explosion exists when performing service

on the battery. To avoid

severe injury

or

DEATH:

■■

■

DO NOT drop the battery. There

is the possibility of risk that the

battery may explode.

■■

■

DO NOT expose the battery to

open flames, sparks, cigarettes

etc. The battery contains combustible gases and liquids.

If these gases and liquids come in contact with a flame

or spark, an explosion could occur.

DANGER - EXPLOSION HAZARDS

DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06) — PAGE 13

1

Emergencies

■

ALWAYS know the location of the

nearest

fire extinguisher

.

■

ALWAYS know the location of the

nearest and

first aid kit

.

■

ALWAYS know the location of the

nearest phone or

keep a phone on

the job site,

in case of emergencies.

■

ALWAYS have easy access to the phone

numbers of the nearest

Ambulance

,

Doctor

and

Fire Department

. This information will

be invaluable in the case of an emergency.

DCA-70USI (60 Hz) — RULES FOR SAFE OPERATION

Check with your local county or state safety towing

regulations, in addition to meeting

Department of

Transportation

(DOT)

Safety Towing Regulations

, before

towing your generator.

CAUTION - FOLLOW TOWING REGULATIONS

■

The maximum speed for highway towing is 55 MPH

unless posted otherwise. Recommended off-road towing

is not to exceed 15 MPH or less depending on type of

terrain.

■

Place

chock blocks

underneath wheel to prevent rolling,

while parked.

■

Use the trailer’s swivel jack to adjust the trailer height to

a level position while parked.

■

Avoid sudden stops and starts. This can cause skidding,

or jack-knifing. Smooth, gradual starts and stops will

improve towing.

■

Avoid sharp turns.

■

Trailer should be adjusted to a level position at all times

when towing.

■

Raise and lock trailer wheel stand in up position when

transporting.

■

Place

support blocks

underneath the trailer’s bumper to

prevent tipping, while parked.

■

Avoid sharp turns to prevent rolling.

■

DO NOT transport generator with fuel in tank.

Towing & Transporting Safety

To reduce the possibility of an accident while transporting

the generator on public roads, always make sure the trailer

that supports the generator and the towing vehicle are in

good operating condition and both units are mechanically

sound.

The following list of safety precautions should be followed

when towing your generator:

■

ALWAYS shutdown engine before transporting.

■

Tighten both fuel tank caps securely.

■

If generator is mounted on a trailer, make sure trailer

complies with all local and state safety transportation

laws. Follow the listed

Towing & Transporting Safety

guidelines for basic towing techniques.

■

Make sure the hitch and coupling of the towing vehicle

are rated equal to, or greater than the trailer "gross vehicle

weight rating.”

■

ALWAYS inspect the hitch and coupling for wear. NEVER

tow a trailer with defective hitches, couplings, chains etc.

■

Check the tire air pressure on both towing vehicle and

trailer.

Trailer tires should be inflated to 50 psi cold.

Also check the tire tread wear on both vehicles.

■

ALWAYS make sure the trailer is equipped with a "Safety

Chain".

■

ALWAYS attach trailer’s safety chains to towing vehicle

properly.

■

ALWAYS make sure the vehicle and trailer directional,

backup, brake, and trailer lights are connected and

working properly.

■

DOT Requirements include the following:

z

Connect and test electric brake operation.

z

Secure portable power cables in cable tray with tie

wraps.

PAGE 14 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

The

DCA-70USI (60 Hz) Whisperwatt

™

Generator

is equipped with a number of safety decals (Figures 2 & 3). These

decals are provided for operator safety and maintenance information. The illustration below and on the preceding page

show the decals as they appear on the machine. Should any of these decals become unreadable, replacements can be

obtained from your dealer.

DCA-70USI (60 Hz) — GENERATOR DECALS

Figure 2. Generator Decals

DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06) — PAGE 15

1

DCA-70USI (60 Hz) — GENERATOR DECALS

Figure 3. Generator Decals (Cont inued)

PAGE 16 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

Figure 4. Typical Generator Grounding Application

DCA-70USI (60 Hz) — INSTALLATION

DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06) — PAGE 17

1

Outdoor Installation

Install the generator in a area that is free of debris,

bystanders, and overhead obstructions. Make sure the

generator is on secure level ground so that it cannot slide or

shift around. Also install the generator in a manner so that

the exhaust will not be discharged in the direction of nearby

homes.

The installation site must be relatively free from moisture

and dust. All electrical equipment should be protected from

excessive moisture. Failure to do will result in deterioration

of the insulation and will result in short circuits and grounding.

Foreign materials such as dust, sand, lint and abrasive

materials have a tendency to cause excessive wear to

engine and alternator parts.

Generator Grounding

To guard against electrical shock and possible damage to

the equipment, it is important to provide a good EARTH

ground.

Article 250 (Grounding) of the National Electrical Code (NEC)

provides guide lines for proper grounding and specifies that

the cable ground shall be connected to the grounding system

of the building as close to the point of cable entry as

practical.

NEC articles 250-64(b) and 250-66 set the following

grounding requirements:

1. Use one of the following wire types to connect the

generator to earth ground.

a. Copper - 10 AWG (5.3 mm

2

) or larger.

b. Aluminum - 8 AWG (8.4 mm

2

) or larger.

2. When grounding the generator (Figure 4) connect the

ground cable between the lock washer and the nut on

the generator and tighten the nut fully. Connect the other

end of the ground cable to earth ground.

3. NEC article 250-52(c) specifies that the earth ground

rod should be buried aminimum of 8 ft. into the ground.

When connecting the generator

to any buildings electrical

system ALWAYS consult with

a licensed electrician.

DCA-70USI (60 Hz) — INSTALLATION

NOTE

Indoor Installation

Exhaust gases from diesel engines are extremely poisonous.

Whenever an engine is installed indoors the exhaust fumes

must be vented to the outside. The engine should be installed

at least two feet from any outside wall. Using an exhaust

pipe which is too long or too small can cause excessive

back pressure which will cause the engine to heat excessively

and possibly burn the valves.

Mounting

The generator must be mounted on a solid foundation (such

as concrete) and set firmly on the foundation to isolate

vibration of the generator when it is running. The generator

must set at least 6 inches above the floor or grade level (in

accordance to NFPA 110, Chapter 5-4.1). DO NOT remove

the metal skids on the bottom of the generator. They are to

resist damage to the bottom of the generator and to maintain

alignment.

Pay close attention to ventilation when operating the

generator inside tunnels and caves. The engine exhaust

contains noxious elements. Engine exhaust must be routed

to a ventilated area.

CAUTION - EXHAUST HAZARD

PAGE 18 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

DCA-70USI (60 Hz) — GENERAL INFORMATION

DCA-70USI Ultra Silent™ (60 Hz) Series Familiarization

Generator

The MQ Power Model DCA-70USI (60 Hz) is a 56 kW

generator

(Figure 5) that is designed as a high quality portable

(requires a trailer for transport) power source for telecom

sites, lighting facilities, power tools, submersible pumps and

other industrial and construction machinery.

Engine Operating Panel

The “Engine Operating Panel” is provided with the following:

■■

■

Tachometer

■■

■

Water Temperature Gauge

■■

■

Oil Pressure Gauge

■■

■

Charging Ammeter Gauge

■■

■

Fuel Level Gauge

■■

■

Pre-Heat Pushbutton

■■

■

Pre-Heat Lamp

■■

■

Panel Light/Panel Light Switch

■■

■

Auto ON/OFF Engine Controller (MPEC)

■■

■

Fuel Leak Detected Alarm Lamp

Generator Control Panel

The “Generator Control Panel” is provided with the following:

■■

■

Frequency Meter (Hz)

■■

■

AC Ammeter (Amps)

■■

■

AC Voltmeter (Volts)

■■

■

Ammeter Change-Over Switch

■■

■

Voltmeter Change-Over Switch

■■

■

Voltage Regulator

■■

■

3-Pole, 175 amp Main Circuit Breaker

■■

■

“Control Box” (located behind the Gen. Control Panel)

■■

■

Automatic Voltage Regulator

■■

■

Current Transformer

■■

■

Over-Current Relay

■■

■

Voltage Rectifer

■■

■

Starter Relay

■■

■

Engine Controller (Computer Controlled)

■■

■

Voltage Selector Switch

Output Terminal Panel

The “Output Terminal Panel” is provided with the following:

■■

■

Three 120/240V output receptacles (CS-6369), 50A

■■

■

Three auxilliary circuit breakers, 50A

■■

■

Two 120V output receptacles (GFCI), 20A

■■

■

Two GFCI circuit breakers, 20A

■■

■

Five output terminal lugs (3Ø power)

■■

■

Battery Charger (Optional)

■■

■

Water Heater (Optional)

Open Delta Excitation System

The DCA-70USI (60 Hz) generator is equipped with the state

of the art "

Open-Delta

" excitation system. The open delta

system consist of an electrically independent winding wound

among stationary windings of the AC output section.

There are four connections of the open delta A, B, C and D.

During steady state loads, the power from the voltage regulator

is supplied from the parallel connections of A to B, A to D,

and C to D. These three phases of the voltage input to the

voltage regulator are then rectified and are the excitation

current for the exciter section.

When a heavy load, such as a motor starting or a short

circuit occurs, the automatic voltage regulator (AVR)

switches the configuration of the open delta to the series

connection of B to C. This has the effect of adding the voltages

of each phase to provide higher excitation to the exciter

section and thus better voltage response during the

application of heavy loads.

The connections of the AVR to the AC output windings are

for sensing only. No power is required from these windings.

The open-delta design provides virtually unlimited excitation

current, offering maximum motor starting capabilities. The

excitation does not have a "

fixed ceiling

" and responds

according the demands of the required load.

Engine

The DCA-70USI (60 Hz) is powered by a 4 cycle, water

cooled, direct injection, turbocharged

ISUZU Model FF-

4BG1T Diesel Engine

. This engine is designed to meet every

performance requirement for the generator. Reference Table

1 for engine specifications.

In keeping with MQ Power's policy of constantly improving

its products, the specifications quoted herein are subject to

change without prior notice.

Electric Governor System

The electric governor system controls the RPMs of the

engine. When the engine demand increases or decreases,

the governor system regulates the frequency variation to

±.25%.

Extension Cables

When electric power is to be provided to various tools or

loads at some distance from the generator, extension cords

are normally used. Cables should be sized to allow for

distance in length and amperage so that the voltage drop

between the generator and point of use (load) is held to a

minimum. Use the cable selection chart (Table 6) as a guide

for selecting proper extension cable size.

DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06) — PAGE 19

1

DCA-70USI (60 Hz) — MAJOR COMPONENTS

Figure 5. Major Components

4elbaT. stnenopmoCrojaMrotareneG

.ONMETINOITPIRCSED

1ylbmessArelffuM

2ylbmessAenignE

3ylbmessAerusolcnE

4ylbmessArotareneG

5ylbmessAlanimreTtuptu

O

6ylbmessAknaTleuF

7ylbmessAyrettaB

8ylbmessAlenaPlortnoCrotareneG

9ylbmessAlenaPgnitarepOenignE

PAGE 20 — DCA-70USI (60 Hz) — OPERATION AND PARTS MANUAL — REV. #0 (01/04/06)

NOTE PAGE

Page is loading ...

MQ Power DCA70USI Operating instructions

This manual is also suitable for

MQ Power DCA70USI Operating instructions

Related papers

Other documents