Aeg-Electrolux S76378KG User manual

SANTO 76378-KG

Electronic Refrigerator/Freezer

Operating Instructions

818 36 54-01/4

2 818 36 54-01/4

Dear customer,

Before placing your new refrigerator/freezer into operation please read

these operating instructions carefully. They contain important

information for safe use, for installation and for care of the appliance.

Please keep these operating instructions for future reference. Pass them

on to possible new owners of the appliance.

1

Notes which are important for your safety or for the proper function-

ing of the appliance are stressed with a warning triangle and/or with

signal words (Warning!, Caution!, Important!). Please observe the fol-

lowing carefully.

0 1. This symbol and numbered instructions guide you step by step in the

operation of the appliance.

2. .....

3

Supplementary information regarding operation and practical uses of

the appliance appear after this symbol.

2

Tips and notes concerning economical and environmentally sound use

of the appliance are marked with the cloverleaf.

Explanations of the technical terminology used in the operating

instructions can be found at the end in the section "Technical

Terminology".

The operating instructions contain instructions for the correction of

possible malfunctions by the user in the section "What to do if ...". If

these instructions should not be sufficient, please contact your local

AEG Service Force Centre.

P

r

i

nte

d

on paper manu

f

acture

d

w

i

t

h

env

i

ronmenta

ll

y soun

d

processes.

he who thinks ecologically acts accordingly ...

818 36 54-01/4 3

Contents

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Environmental Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Appliance Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Fitting the Door Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

The refrigerator/freezer needs ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Appliance Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Carbon filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Reversing The Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Appliance Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

View of Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Freezer tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Cold Accumulation Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Temperature setting buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Temperature Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

ALARM OFF button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Prior to Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Temperature Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

COOLMATIC/FROSTMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

COOLMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

FROSTMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Holiday Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Switching the Appliance Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Contents

4 818 36 54-01/4

Control and Information Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

"Open Door"-Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Temperature Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Function Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Opening the Freezer Compartment Door . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Storage Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Variable Inner Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

LONGFRESH 0 °C cold zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Quick Chill Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Bottle- and Can Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Dismantling of the Bottle- and Can Holder . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Bottle Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Correct storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Frozen Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Storage Goods Symbols/Freezing Calendar . . . . . . . . . . . . . . . . . . . . . . . . . 36

Preparation of Ice Cubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Hints and Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Normal Operating Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Food Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Energy Saving Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Internal Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

External Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Replacing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Technical Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Guarantee Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Service & Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

818 36 54-01/4 5

1 Important Safety Instructions

These warnings are provided in the interests of your safety. Ensure

that you understand them all before installing or using this

appliance. Your safety is of paramount importance. If you are unsure

about any of the meanings of these warnings contact the Customer

Care Department.

Prior to Installation

• Check the refrigerator/freezer for transport damage. Under no

circumstances should a damaged appliance be installed! In the event

of damage, please contact your retailer.

Installation

• This appliance is heavy. Care should be taken when moving it.

• It is dangerous to alter the specifications or attempt to modify this

product in any way.

• Ensure that the appliance does not stand on the electrical supply

cable. If the supply cable is damaged, it must be replaced by a cable

available from your local Service Force Centre.

• Make sure that the power plug is not squashed or damaged by the

back of the fridge/freezer. A damaged power plug may overheat and

cause a fire.

• If the power plug socket is loose, do not insert the power plug. There

is a risk of electric shock or fire.

• Any electrical work required to install this appliance should be carried

out by a qualified electrician or competent person.

• Parts which heat up should not be exposed. Whenever possible, the

back of the appliance should be close to a wall, but leaving the

required distance for ventilation, as stated in the installation

instructions.

• The appliance should be left for 2 hours after installation before it is

turned on, in order to allow the refrigerant to settle.

Refrigerant

The refrigerant isobutane (R600a) is contained within the refrigerant

circuit of the appliance, a natural gas with a high level of

environmental compatibility, which is nevertheless flammable.

• During transportation and installation of the appliance, be certain

that none of the components of the refrigerant circuit become

damaged.

Important Safety Instructions

6 818 36 54-01/4

• If the refrigerant circuit should become damaged:

– avoid open flames and sources of ignition;

– thoroughly ventilate the room in which the appliance is situated.

Child Safety

• Do not allow children to tamper with the controls or play with the

product. Inform children of the possible dangers and instruct them in

the correct use of the appliance.

• Keep packaging material away from children! (There is a risk of

suffocation!)

During Use

• This appliance is designed for domestic use only, specifically for the

storage of edible foodstuffs only. It is not intended for commercial or

industrial use

• Containers with flammable gases or liquids can leak at low

temperatures. Do not store any containers with flammable materials

such as, spray cans, fire extinguisher refill cartridges etc in the

freezer.

• Frozen food should not be refrozen once it has thawed out.

• Do not place carbonated or fizzy drinks in the freezer.

• Ice lollies can cause ’frost/freezer burns’ if consumed straight from

the freezer compartment. Inform children of this danger.

• Do not remove items from the freezer compartment if your hands are

damp/wet, as this could cause skin abrasions or frost/freezer burns.

• Bottles and cans must not be placed in the freezer. They can burst

when the contents freeze.

• Manufacturers´ recommended storage times should be adhered to.

Refer to relevant instructions.

Maintenance and Cleaning

• Before cleaning, always switch off the appliance and disconnect from

the electrical supply.

• When unplugging always pull the plug from the mains socket, do not

pull on the cable. Damage to the cord may cause a short circuit, fire

and/or electric shock.

Servicing

• This product should be serviced by an authorised engineer and only

genuine spare parts should be used.

• Under no circumstances should you attempt to repair the appliance

yourself. Repairs carried out by inexperienced persons may cause

injury or serious malfunctioning.

Contact your local AEG Service Force Centre.

818 36 54-01/4 7

Environmental Information

2

Packaging material

The packaging materials are environmentally friendly and can be recy-

cled. The plastic components are identified by markings, e.g. >PE<,

>PS<, etc. Please dispose of the packaging materials in the appropriate

container at your local waste disposal facilities.

2 Old appliance

The symbol

W on the product or on its packaging indicates that this

product may not be treated as household waste. Instead it shall be

handed over to the applicable collection point for the recycling of elec-

trical and electronic equipment. By ensuring this product is disposed of

correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by

inappropriate waste handling of this product. For more detailed infor-

mation about recycling of this product, please contact your local city

office, your household waste disposal service or the shop where you

purchased the product.

When disposing of your old appliance:

Make the appliance unusable by cutting off the cable and remove any

door catches to ensure small children cannot be trapped inside.

Help to keep your country tidy - use an authorised disposal site.

Appliance Transport

Two persons are required to transport the appliance. Two handles are

provided on the back of the appliance at the top to enable a better

hold. Before transporting, the plinth cover must be removed to prevent

damage.

0 1. To remove the plinth cover from

the stops, tilt downwards and then

pull forwards.

Important: Do not damage door

contact (if present).

8 818 36 54-01/4

2. Grip the appliance with the

recessed handles positioned as

in the drawing, and transport

the appliance.

3. In order to push the appliance

into its final position, press care-

fully at the top of the door and

tip the appliance back slightly.

The weight is thus transferred to

the back wheels and the appliance can be easily pushed.

4. When the appliance is standing in the desired place, attach the plinth

cover. Make sure that the door contact (if present) is not damaged and

that it engages in the corresponding aperture in the plinth cover.

Before Use

Packaging

0 1. Remove all adhesive tape and packaging from the interior of the appli-

ance.

3

Any remnants of adhesive can be removed with white spirit.

2. Remove the transport protection pieces and pull off the adhesive tape.

818 36 54-01/4 9

3. Wash the inside of the appliance with lukewarm water with a little

bicarbonate of soda added (5 ml to 0.5 litre of water). Do not use soap

or detergent as the smell may linger. Dry the appliance thoroughly.

Remove the transport fittings from

the storage shelves:

4. Slide the fittings securing the shelf

forward to the thicker section on

the edge of the storage shelf.

5. Take hold of the shelf at the back

and together with the fittings slide

the storage shelf far enough for-

ward so that it can be hinged

downwards and the fittings can be

removed from the guides.

Fitting the Door Handles

To keep the amount of packaging down and to reduce the size for

transporting, the door handles are not mounted when the appliance is

delivered.

1

Take care! Do not tighten screws too tightly (max. 2 Nm), the door

handles could be damaged.

The handles are packed separately on the padding in front of the door,

the brackets and screws inside the appliance.

To mount, lay the appliance carefully on its back, if necessary. Use a

piece of padding or a blanket as protection under the appliance.

0 1. Screw the top door bracket to the

door handle (1). Mount the

bottom door bracket to the

bottom of the door (2).

Important: Ensure door handle is

correctly positioned

10 818 36 54-01/4

2. Mount top door bracket on the

top of the door (3) and screw

handle to bottom door bracket

(4).

Installation

Installation Location

The appliance should be installed in a well ventilated, dry room.

Energy use and efficient performance of the appliance is affected by

the ambient temperature.

The appliance should therefore

– not be exposed to direct sunlight;

– not be installed next to radiators, cookers or other sources of heat;

– only be installed at a location whose ambient temperature

corresponds to the climate classification, for which the appliance is

designed.

The climate classification can be found on the rating plate, which is

located at the left on the inside of the appliance.

The following table shows which ambient temperature is correct for

each climate classification:

If installation next to a source of heat is unavoidable, the following

minimum clearances must be maintained at the sides of the appliance:

– for electric cookers 3 cm;

– for oil and coal fired ranges 30 cm.

If these clearances cannot be maintained a heat insulating pad is requi-

red between the cooker and the refrigeration appliance.

Climate classification for an ambient temperature of

SN +10 to +32 °C

N +16 to +32 °C

ST +18 to +38 °C

T +18 to +43 °C

Installation

818 36 54-01/4 11

The refrigerator/freezer needs ventilation

Air is fed under the door through the

vent slots in the base and is exhausted

upwards along the back wall. To ensure

proper air circulation never cover or

alter the vent openings.

Important! If the appliance is installed

under a hanging cabinet, a clearance of

at least 10 cm between the top of the

appliance and the cabinet above it must

be maintained.

Please check whether, after installing

your appliance and especially after

reversing the door, the door seal seals

tightly. A badly fitting door seal may

lead to heavy frosting and a higher

power consumption (see also "What to

do if ...“).

0 1. Remove the two wall spacers from

the appliance accessories pack and,

in accordance with the illustrations,

fix them at the top of the rear of the

appliance so that the distance from

the wall required for the necessary

ventilation is ensured.

Appliance Alignment

The appliance must stand on a firm horizontal surface.

0 1. Please level out unevennesses in the

floor by screwing the two adjustable

front feet in or out using the 13 mm

spanner supplied. To do this remove

the plinth panel (see chapter

“Transporting the appliance“)

Installation

12 818 36 54-01/4

Electrical Connection

Any electrical work required to install this appliance should be carried

out by a qualified electrician or competent person.

1

WARNING – THIS APPLIANCE MUST BE EARTHED

The manufacturer declines any liability should these safety measures

not be observed.

Before switching on, make sure the electricity supply voltage is the

same as that indicated on the appliance rating plate. The rating plate is

inside, on the left.

The appliance is supplied with a 13 amp plug fitted. In the event of

having to change the fuse in the plug supplied, a 13 amp ASTA

approved (BS 1362) fuse must be used.

Important

The wires in the mains lead are coloured in accordance with the

following code:

Green and Yellow Earth

Blue Neutral

Brown Live

As the colours of the wires in the

mains lead of this appliance may

not correspond with the coloured

markings indentifying the

terminals in your plug, proceed

as follows:

1. The wire coloured green and

yellow must be connected to

the terminal marked with the

letter "E“ or by the earth

symbol or coloured green and yellow.

2. The wire coloured blue must be connected to the terminal "N“ or

coloured black.

3. The wire coloured brown must be connected to the terminal marked

"L“ or coloured red.

4. Upon completion there must be no cut, or stray strands of wire

present and the cord clamp must be secure over the outer sheat.

1

Warning! A cut-off plug inserted into a 13 amp socket is a serious

safety (shock) hazard. Ensure that the cut-off plug is disposed of safely.

Blue

Green

& Yellow

Brown

Cord Clamp

Installation

818 36 54-01/4 13

Carbon filter

There is a active carbon filter in the rear wall of the fridge section. The

carbon filter cleans the air in the fridge section and in the LONGFRESH

0°C cold section by binding unpleasant smells.

Tip: The active carbon filter is a part subject to wear and is not covered

by the warranty.

Inserting and changing the active carbon filter:

When the fridge is delivered, the carbon filter is packed in a plastic bag

to ensure a long life. Before using the appliance for the first time, the

carbon filter must be inserted behind the air discharge grill.

With the fridge operating normally, the

carbon filter should be changed once a year to

ensure optimum function.

New carbon filters can be obtained from

specialist dealers or from the customer care

department.

0 1. To open the grill, press the lever on the right

of the grill (1) and open the grill forwards (2).

2. To change the old carbon filter, pull it from

the runners (3).

3. Insert the new carbon filter into the runners

of the grill (3) and press the grill closed until

it snaps into place.

1

Take care when handling the filter to prevent

dislodging carbon particles.

14 818 36 54-01/4

Reversing The Door

The door hinges can be changed if required to suit the location where

the appliance is installed.

1

Warning! Unplug from the mains, before reversing the door.

0 1. Open the freezer compartment

door and remove the plinth to

the front. Move the door bearing

cover on the plinth from the left

to the right.

2. Close the freezer compartment

door. Open the fridge compart-

ment door and unscrew the

retaining screw for the self-clos-

ing mechanism on the top of the

freezer compartment door.

3. With the freezer compartment

door closed, remove the cross-

head screws from the lower door

bearing and remove the door

bearing downwards.

4. Move the bearing pivot from the

right to the left hand hole.

Remove the freezer compartment

door carefully to the front and

place on one side.

Reversing The Door

818 36 54-01/4 15

5. Unscrew the centre door bearing.

6. Remove the fridge compartment

door carefully to the front and

place on one side.

7. Unscrew the retaining screw for

the self-closing mechanism on the

bottom of the fridge compart-

ment door.

8. Move the upper bearing pivot to

the left.

9. Unscrew the top handle bracket

from the handle rod (1). Unscrew

the bottom handle bracket from

the door (2).

10. Unscrew the top handle bracket

from the door (3) and screw onto

the bottom right-hand side of the

door (4).

1

Caution! Do not overtighten the

screws (max. 2 Nm) as you may

damage the door handles.

Reversing The Door

16 818 36 54-01/4

11. Turn the handle bracket with the

handle rod 180° and screw them

to the door (5) and the fitted han-

dle bracket (6).

1

Caution! Do not overtighten the

screws (max. 2 Nm) as you may

damage the door handles.

12. Fasten the self-closing mechanism

to the bottom left of the fridge

compartment door.

13. Carefully slide the fridge com-

partment door onto the top bear-

ing pivot and close.

14. Slide the centre door bearing into

the bottom left of the fridge com-

partment door and fasten to the

housing.

Reversing The Door

818 36 54-01/4 17

15. Fasten the self-closing mechanism

on the top left of the freezer

compartment door.

16. Carefully slide the freezer com-

partment door onto the centre

bearing pivot and close.

17. Place the lower door bearing with

the bearing pivot in the lower left

of the freezer compartment door

and fasten.

18. Open the freezer compartment

door and fit the plinth.

Important: Do not damage door contact (if present).

18 818 36 54-01/4

Appliance Description

View of Appliance

(various models)

á Control panel

à Butter and cheese compartment with lid

â Door storage compartments

ä Bottle compartment

ã LONGFRESH 0 °C cold zone

å Shelves

ç Quick chill shelf

é Bottle and can holder

è Rating plate

ê Air discharge grill with regulator

ë Freezer drawer (only for storage). When defrosting the bottom

drawer also serves as a water collecting vessel

í Freezer drawer (for storage and freezing)

ì Freezer tray

Appliance Description

818 36 54-01/4 19

Freezer tray

A freezer tray is included below the

upper drawer in the freezer

compartment.

Berries and vegetables, for example,

can be pre-frozen on the freezer tray.

Advantage: The berries are not squeezed and maintain their natural

form. The frozen berries can then be stored in compartments or drawers

packaged in individual portions.

Cold Accumulation Block

A cold accumulation block is enclosed with the appliance.

3

In the event of power failure or a malfunction of the appliance, the

cold accumulation block will increase the hold over period by several

hours. The cold accumulation block cools best if it is placed in the top

drawer at the front on the frozen food. If the freezer section is only

partially filled, pack the frozen food together as tightly as possible, so

that in the event of a power cut the cold remains in the frozen food for

longer.

When freezing food, place the cold accumulation block on the already

frozen food to prevent defrosting due to the warmth of the food that is

being frozen.

When defrosting the appliance place the cold accumulation block on

top of the frozen food to keep it cold.

The block may also be used in a cool bag to keep the temperature of

food down during transportation.

Refer to the section "Prior to Initial Start-Up" regarding the freezing of

the cold accumulation block.

Appliance Description

20 818 36 54-01/4

Control Panel

1 ON/OFF button and ON/OFF indicator light (green)

2 Temperature display for refrigerator (not for LONGFRESH 0 °C

cold zone)

3 Temperature setting buttons for refrigerator

4 COOLMATIC button and COOLMATIC indicator light (yellow)

• COOLMATIC for intensive cooling in the refrigerator

5 FROSTMATIC button and FROSTMATIC indicator light (yellow)

• FROSTMATIC for fast freezing in the freezer compartment

6 Temperature display for freezer compartment

7 Temperature setting buttons for freezer compartment

8 ALARM OFF button and warning indicator light (red)

(see section: "Control and Information Systems")

Temperature setting buttons

The temperature is adjusted using the

„+“ (WARMER) and „-“ (COLDER) buttons.

These buttons are connected to the temperature display.

• The temperature display is switched over from the display of the

ACTUAL temperature (Temperature display is illuminated) to the dis-

play of the DESIRED temperature (Temperature display flashes) by

pressing one of the two buttons, „+“ (WARMER) or „-“ (COLDER).

• Each time one of the two buttons is pressed again the DESIRED tem-

perature is adjusted by 1 °C.

• If neither button is pressed, the temperature display automatically

switches back after a short period (approx. 5 sec.) to the display of

the ACTUAL temperature.

DESIRED temperature means:

The temperature that has been selected for inside the fridge or the

freezer compartment. The DESIRED temperature is indicated by flashing

numbers.

Page is loading ...

Aeg-Electrolux S76378KG User manual

This manual is also suitable for

Aeg-Electrolux S76378KG User manual

Related papers

Other documents