Documentation Number ES1A-2907qs pn6911-rev002
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
815-433-5100 Fax 433-5104 www.bb-elec.com orders@bb-elec.com [email protected]
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
Documentation Number ES1A-2907qs pn6911-rev002
+353 91 792444 Fax +353 91 792445
www.bb-europe.com orders@bb-europe.com [email protected]m
1
2
4
5
6
7
8
3
RS-232 to Ethernet Converter
Model: ES1
A
Quick Start Guide
C
C
h
h
e
e
c
c
k
k
y
y
o
o
u
u
r
r
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
s
s
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
S
S
e
e
t
t
u
u
p
p
Connect your PC to the network
Connect the ES1A serial port to your serial
device (Use a serial cable if it is DCE; null
modem cable if it is DTE.)
Connect the ES1A Ethernet connector to a
network switch or hub (Cat-5 cable)
C
C
o
o
n
n
f
f
i
i
g
g
u
u
r
r
e
e
t
t
h
h
e
e
E
E
S
S
1
1
A
A
G
G
e
e
t
t
t
t
h
h
e
e
I
I
P
P
A
A
d
d
d
d
r
r
e
e
s
s
s
s
The
ES1A
module
5VDC 500 mA power supply
A printed version of user manual
A printed version of this ES1A Quick Start Guide
CD-ROM disk with Discovery software, RealPort
software, manual, Quick Start Guide
Use the Discovery software on your CD
(
finder.exe
)
to
g
et the IP address for
y
our ES1
A
S
S
e
e
t
t
u
u
p
p
V
V
C
C
O
O
M
M
For Win 2K/XP/Vista, start the RealPort software
wizard (located on the included CD via setup.exe)
Select your ES1A from the list
Select an unused COM port number
Follow the wizard to set up a virtual COM port
For Win 98, ME, NT 4.0,follow the readme.txt
included with each O/S (no setup.exe available)
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
Configure and then start your application
In the Configuration, Serial Ports page,
select the
Port Profile you require for use with your application
(e.g. RealPort for virtual COM port, TCP Server, UDP
server, Serial Bridge, etc.)
Configure the serial port settings for the selected Port
Profile (e.g. In TCP Sockets select client or server,
TCP port numbers, etc.) Also configure baud rate,
data bits, etc in Basic Serial Settings.
Configure any required alarms and notification
If RealPort profile was selected (virtual COM port) do
the next step (Set up VCOM)
Power is applied when the 5VDC power supply is
connected
When a connection is established with the network,
the yellow LED will illuminate
The ES1A will automatically try to obtain an IP
address, or generate one itself
P
P
o
o
w
w
e
e
r
r
I
I
t
t
U
U
p
p
In a web browser on your PC, type in the
IP address and access the Web
Configuration and Management Interface
Log in using the username ‘root’ and
password ‘dbps’
L
L
o
o
g
g
i
i
n
n
/
