Nilfisk-Advance APC 328 Instructions For Use Manual

Brand: Nilfisk-Advance

Model: APC 328

Category: Floor Machine

Type: Instructions For Use Manual

A-English

Instructions for Use

Original Instructions

5/10 revised 1/12

FORM NO. 56041948

Models: 600303281, 600303282

APC328

INSTRUCTIONS FOR USE

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops, and ofﬁ ces other than

normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the following:

WARNING!

To reduce the risk of ﬁ re, electric shock, or injury:

• Do not leave the machine unattended when it is plugged-in. Unplug the unit from the power outlet when not in use.

• Always use a defoamer when foaming occurs to prevent damage to vacuum motor(s).

• Unplug the machine from the power outlet before cleaning or servicing.

• To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

• Wear hearing protection if desired.

• Do not allow to be used as a toy. Close attention is necessary when used near children.

• Use only the manufacturer’s recommended attachments.

• Inspect the power cord regularly for damage, such as cracking, ageing, or damaged insulation. Replace the power cord with the

same type as original if any damage is found. Do not use with damaged cord or plug.

• Use approved chemicals only. Never use solvents.

• Do not let the pump run dry.

• If the machine is not working as it should, has been dropped, damaged, left outdoors or ﬂ ooded with water, return it to a service

center.

• Do not pull the machine by the cord, do not use the cord as a handle, close a door on the cord, or pull the cord around sharp

edges or corners. Do not run the machine over the cord. Keep the cord away from heated surfaces. To unplug, grasp the plug,

not the cord.

• Extension cords must be 12 gauge and no longer than 15 m. Replace the cord or unplug immediately if the ground prong

becomes damaged.

• Never ﬁ ll the tank with water above 54º C.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may

reduce air ﬂ ow.

• Keep loose clothing, hair, ﬁ ngers, and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or any health endangering dusts.

Do not use to pick up ﬂ ammable or combustible liquids such as gasoline or use in areas where they may be present.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure,or chemical content.

SAVE THESE INSTRUCTIONS

revised 1/12

A-2 APC328 - 56041948 5/10

INSTRUCTIONS FOR USEA - ENGLISH

INSPECTION:

Carefully unpack and inspect your APC328 for shipping damage. Each machine is tested and inspected before shipping. Any shipping damage

incurred is the responsibility of the carrier. You should notify the carrier immediately if you notice damage to the box or to the machine or parts.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals. Powder chemicals may be used, but unless mixed very thoroughly they could cause a build-up in the

pump, lines, heat exchanger and/or quick disconnects. Any problem caused by a chemical build-up is not covered by warranty. Use a neutral

cleaner with a pH between 5 and 10 to avoid premature wear of the pump, seals, and/or other components.

MAINTENANCE:

For optimum performance ﬂ ush the machine with clear water at the end of each working day. Once a month, minimum, run a ﬂ ushing compound

through the machine to break up any mineral or chemical build-up that may have formed. The vacuum motor and the pump do not require any

scheduled maintenance; however, the motor may require replacement brushes after 1000 - 1500 hours. Clean the body with an all-purpose

detergent, and protect it with an automobile interior polish. Lubricate the wheels, castors, and quick disconnects with an all purpose silicone spray.

Refer to the maintenance schedule on page 9.

PARTS AND SERVICE:

Repairs, when required, should be performed by your authorized distributor who maintains an inventory of original replacement parts and

accessories. Call the distributor from whom you purchased this machine if you need parts and service. Be sure to specify the machine model.

Have your serial number at hand.

Serial Number: __________________ Model: APC328

Purchase Date:_____________

Write the name and phone number of your distributor:

____________________________________________________________________

Be sure to register your purchase to activate your warranty

revised 1/12

5/10 A-3 56041948 - APC328

ENGLISH - AINSTRUCTIONS FOR USE

KNOW YOUR MACHINE

Operator Handle (1): Operator holds onto this handle to move the machine from one location to another.

Solution Tank Lid (2): This lid screws off so the tank can be ﬁ lled. The solution ﬁ ll hose is tethered to the lid, and hangs inside the arm of the

Operator Handle.

Maid’s tote and Recovery tank lid (3): This removable container holds often-used items and has a handle for easy carrying. The recovery tank

lid sits under the maid’s tote and covers the opening in the Recovery Tank. This is where the operator can access the tank to clean it and the ball

ﬂ oat cage. The tank can be ﬂ ushed out by running clean warm water into this opening and laying the open drain hose into a bucket or drain.

Recovery Hose (4): Waste water is picked-up through this hose.

Spray Hose (5): This hose delivers water from the machine to the cleaning tool.

Drain Hose (6): This hose is used to empty the recovery tank. NOTE: hold the end of the hose above the water level in the tank to avoid sudden,

uncontrolled ﬂ ow of waste water when you remove the cap, then lower the hose slowly to control the rate of discharge.

Castors and Wheels (7): Castors pivot for ease of steering, and large back wheels make it easy to roll the machine from location to location.

Chemical Feed Lines (8): These clear tubes connect the cleaning chemical containers to the machine where the chemical can be siphoned into

the outlet water from the pump. Metering tips -- used to change the ratio of water to chemical -- are installed here.

Switch Plate (9): The machine’s on/off switches for the vacuum and for the pump are located here and this is where the valve to change chemical

feeds is located.

Power Cord (10): The 25 ft. power cord connects to a power cord pigtail on the rear of the machine.

Chemical Container Holders (11): Two molded-in bottle holders for chemical jugs.

Tools & Accessories (12): Various accessories

can be stored on the machine.

revised 1/12

A-4 APC328 - 56041948 5/10

INSTRUCTIONS FOR USEA - ENGLISH

METERING TIPS

COLOR HOLE SIZE MIX RATIO FLOW RATE

Orange 0.007 1 oz : 128 oz 1.0 oz/gal

Pink 0.012 1 oz : 64 oz 2.5 oz/gal

Dark Green 0.014 1 oz : 50 oz 3.0 oz/gal

Yellow 0.016 1 oz : 32 oz 5.0 oz/gal

Light Blue 0.020 1 oz : 20 oz 6.0 oz/gal

Burgundy 0.022 1 oz : 15 oz 9.0 oz/gal

Black 0.048 1 oz : 5 oz 20 oz/gal

KNOW YOUR SWITCH PLATE

Vacuum Switch (A): turns on the vacuum motor.

Chemical Valve (B): switches between the two chemical containers. When the selector is pointed straight down, the valve is off and neither

chemical is selected. When the selector is pointed directly towards one or the other symbols, that chemical is selected.

Solution Pump Switch (C): turns on the solution pump.

Quick Connect (D): this is where solution comes out of the machine and the attachment point for the solution hose.

METERING TIPS

The chemical metering tips allow you to select the ratio of chemical to water, as the water ﬂ ows out of the machine. Insert the correct metering tip

for the desired mixture into the chemical siphon tube.

revised 1/12

5/10 A-5 56041948 - APC328

ENGLISH - AINSTRUCTIONS FOR USE

SET-UP AND USE

1) Insert the appropriate metering tips into the chemical feed lines (see illustration, page 5).

2) Fill the holding tank with warm water (not exceeding 54 °C). Do not add any chemical to the tank.

3) Prepare the area for cleaning by emptying waste receptacles, clearing debris, removing paper products, blowing out vents, and sweeping

ﬂ oors.

4) PRIME THE PUMP: Attach the priming hose to the outlet quick disconnect (D) and place the open end of the hose into the recovery tank.

Turn on the pump (C) and let it run until the pump is completely primed (no visible air in the water stream). Turn the pump off.

NOTE: prime the machine before you place the chemical feed tubes into chemical containers.

5) Disconnect the priming hose and attach the solution hose (5) to the quick disconnect (D).

6) Attach the spray gun (E) to the other end of the solution hose (5).

7) Place chemicals in the molded-in chemical bottle containers (11) on the rear of the machine. Insert one of the feed lines into one of the

chemical containers. Secure the line by screwing on the cap. The chemical will feed from which ever container the selector valve on the

switch plate (9) is turned towards and when the gun is used in the low pressure setting. Use chemicals with a pH of between 5 and 10. Never

add chemicals to the clean water tank.

8) Set the spray gun (E) to low pressure by sliding the pressure selector forward (low pressure = forward; high pressure = back).

9) Turn on the pump switch (C) (push button) and spray through the gun for a few seconds to ﬁ ll the line with solution.

10) Apply the chemical to the walls and ﬁ xtures from the bottom up. Spray the ﬂ oor last as you work your way out of the room.

11) Allow the chemical to work for the proper amount of dwell time, according to the chemical manufacturer’s directions. Agitate heavily soiled

areas with a scrub brush.

12) Turn off the chemical injector valve (B) by turning the selector to the down position.

13) Set the spray gun (E) to high pressure and rinse the area from the top down.

14) Connect the vacuum hose (4), attach the squeegee (F), and turn on the vacuum (A) (rocker switch).

15) Squeegee off the mirrors, pick up the liquid off the ﬂ oor with the ﬂ oor tool. If you have the optional blow dry hose, use it to dry the ﬁ xtures.

16) Drain the recovered water into a utility sink or toilet. NOTE: Keep the top of the drain hose (6) higher than the water level in the tank to avoid

uncontrolled discharge of water when you open the cap on the hose.

CAUTION

To avoid vacuum motor damage, always use a defoamer any time foam is present.

Before you turn on the vacuum always make sure the ﬁ lter screen on the ball ﬂ oat is clean and that the ball can travel freely.

RE-PRIMING THE PUMP

If the pump looses prime between jobs, follow the instructions to PRIME THE PUMP, above. If that doesn’t get water ﬂ owing, put the priming hose

into the vacuum inlet hose barb and cover the rest of the space around the priming hose with your hand. Turn on the vacuum (with the pump also

running) and let the suction of the vacuum assist in getting water into the pump.

revised 1/12

A-6 APC328 - 56041948 5/10

INSTRUCTIONS FOR USEA - ENGLISH

revised 1/12

5/10 A-7 56041948 - APC328

ENGLISH - AINSTRUCTIONS FOR USE

MAINTENANCE

1) Use only approved chemicals at the recommended mix ratios. All chemicals should be added through the feed system and NOT added

directly to the water in the solution tank to prevent possible damage to the pump, seals, or other components.

2) For optimum performance, ﬂ ush the Chemical Feed lines after every job by replacing the chemical containers with containers of clear water

and spraying through the gun until the ﬂ uid stream is clear. See the Maintenance Schedule, below.

3) The pump seals and/or valves in the high pressure pumps may need to be replaced after about 1000 hours of use, if the pump begins to lose

performance or to leak. The pressure regulator valve may need to be when a drop in the spraying pressure at the tool is apparent.

MAINTENANCE SCHEDULE

ITEM DAILY WEEKLY YEARLY

Flush chemical lines X

Check/clean vac inlet ﬁ lter X

Clean solution ﬁ lter X

Check vacuum motor airways X

Check pump for leaks X

Check vacuum motor brushes * X

* Have your distributor check the carbon brushes once a year or after about 500 hours of operation.

TECHNICAL SPECIFICATIONS (as installed and tested on the unit)

MODELS 600303281, 600303282

VACUUM MOTOR(s): Two stage, 8 Amp

WATER LIFT: 23 kpa

AIR FLOW: 100 CFM

TANK CONSTRUCTION: Rotationally molded polyethylene

HEIGHT: 98 cm X 59 X 86.5 cm

WEIGHT 50 KG

TECHNICAL SPECIFICATIONS (as installed and tested on the unit)

Model APC328 APC328

Model No. 600303281 600303282

Voltage/frequency V/Hz 220-240 / 50-60 220-240 / 50-60

Rated Current Amp 3.5 6.7

Protection Class (electrical)

Protection Grade IP34 --

Sound Pressure Level IEC 60335-2-72: 2002 Amend. 1:2005, ISO 11201 dB (A)/20μPa 76 75

Total Weight lbs/kg 67 / 30 67 / 30

Vibrations at the Hand Controls (ISO 5349-1) m/s20.87m/s20.87m/s2

Solution Tank Capacity 5 gal (19l) 5 gal (19l)

A-8 APC328 - 56041948 5/10

INSTRUCTIONS FOR USEA - ENGLISH

revised 1/12

BASE ASSY

D-2 APC328 - 56041948 5/10

PARTS LIST

BASE ASSY

Kit Item Ref. No. Qty Description

# 600732879 1 Holding Tank/Base Complete For (includes 1-33)

K6 1# 1 Bolt Hex 1/4-20 X 3/4 Full

K2,K6 2# 9 Washer Flat 3/16 Zinc Plat

K7 3# 1 Elect Butt Conn 10-12 Ga Non-I

K3 4# 1 Fitting-Adapter-Brass-3-4x3-8

K5,K6 5# 6 Nut-Nylon Lock-Ss-8-32

K5 7# 1 Lid And Ring 4 Lid Clear

K7 8# 1 5’ Hose Fill Apc

K6 9# 1 Bolt-Hex-1/4-20 X 1/2-Ss

10# 1 Washer-Fender-1/4 Id-1 Od-Ss

11# 3 Washer Internal Tooth 10

K6 12# 1 Clip Handle Black Vinyl Coated

K6 13# 1 Strap/Buckle Cord Wrap W/Spur

K4 14# 2 Grommet 3/4 Id X 3/16 Panel

K3 15# 1 Cap Garden Hose 3/4 Fght N

K1 16# 2 Wheel 10 Grey Plastic Insert

17# 56380594 1 Caster-Plate-Orca

K4 18# 56380696 1 Foam Reticulated 20 Ppi 1/2 X

19# 56380755 2 Plug Square Tube Smooth 3/4

20# 56380942 1 Gasket For Apc Closed Cell B

K7 21# 56601599 1 Cap - Raw With Tether

K7 22# 1 Adapter Faucet Inside/Outsid

K6 23# 1 Strap-Black-Poly Web-0.75

K1,K6 24# 27AUSP 2 Axel Cap Black Pal Nut

K6 25# 1 Bolt-Php-Ss-8-32x1/2

K5 26# 6 Screw 8-32 X 7/8 Panhead Phi

K2 27# 8 Screw 1/4-20 X 5/8 Hesx

K6,K7 28# 1 Tie Wire 8 W/Mounting Hole

K6 29# 2 Hinge Pin 1/4 X 2.25 S/S

K2 31# 905USP 2 Caster Swivel 4 Gray Non Ma

K1 32# 1 Axel Rod Zinc Plated 1/2 Ro

33# 56380795 1 Holding Tank/Base Drilled And

[ ]# 600732872 1 Label Kit APC-328

K1# 600732852 1 Wheel Axel And Axel Cap

K2# 600732850 1 Castor And Hardware APC-328

K3# 600732849 1 Drain Fitting And Cap

K4# 600732859 1 Grommets Rubber Pump Hose Pr

K5# 600732856 1 Lid And Ring 4 Inch

K6# 600732858 1 Fasteners All Cleaner APC T

K7# 600732848 1 Lid And Fill Hose Solution Ta

[ ] = Not Shown

* = Optional, Not Included

# = Revised or new since last update

revised 1/12

5/10 D-3 56041948 - APC328

PARTS LIST

EQUIPMENT PALLET

11 10

17A

18 19

revised 1/12

D-4 APC328 - 56041948 5/10

PARTS LIST

EQUIPMENT PALLET

Item Ref. No. Qty Description

# 600732876 1 Pallet Complete APC-328 (includes 1-20)

1# 6 Washer Flat 3/16 Zinc Plat

# 1 Plug For A .875 Hole Used On

K1 3# 2 Hose Clamp 3/4 I.D. For Hhp

K2 4# 1 Vac Motor, 120v

K2 5# 4” Hose 2 Id 50 Length Rb

K1 6# 3 Washer 1/4 I.D. 1 O.D. F

K4 7# 1 Hose Vacuum Clear 1-1/2 X

K1 8# 2 Screw Thumb 1/4-20 X 1 Type

9# 3 Bolt 1/4-20

10# 1 Sleeve Vacuum Outlet For Hos

K2 11# 1 Gasket 1 Side Adhesive 5 1/2

12# 230USP 1 Retainer Power Cord Water T

13# 1 Switch Assembly Pump & Vac Onl NOTE 1

14# 56380839 1 Pallet Drilled And Prepped. N

15# 1 Bolt Hex 1/4-20 X 1-3/4

16# 1 Pump Assembly For Apc 120v. W/ NOTE 2

17# 600732873 1 Power Cord Kit (model 600303281)

17A# 600732887 1 Power Cord Kit (model 600303282)

K3 18# 1 Filter Electrical Emi Suppres

19# 2 Screw 8-32 X 5/8 Panhead

20# 2 Nut Nylon Lock 8-32 Stainles

K1# 600732858 1 Fasteners All Cleaner APC T

K2# 600732883 1 Vacuum Motor Kit APC328

K3# 600732889 1 Emi Suppression Filter

K4# 600732846 1 Hoses Drain Priming Vacuum

# = Revised or new since last update

NOTE 1: See SWITCH PLATE ASSY.

NOTE 2: See PUMP ASSY.

revised 1/12

5/10 D-5 56041948 - APC328

PARTS LIST

PUMP ASSY

revised 1/12

D-6 APC328 - 56041948 5/10

PARTS LIST

PUMP ASSY

Kit Item Ref. No. Qty Description

K3,K4 1# 4 Bolt-Hex-Flthrd-Ss-Zp-1-4-20x1

K3,K4 2# 4 Nut-Nylock-Zp-1-4-20

K3,K4 3# 8 Washer Flat 3/16 Zinc Plat

K3,K4 4# 1 Hose Barb 1/4 Pipe X 1/2 Hose Brass

K3,K4 5# 2 Plug Brass Pipe 1/4 Pipe H

K3,K4 6# 1 Reducer 3/8 Pipe Female To 1

K3,K4 7# 4 Washer-Flat-1/4x3/4x1/8-60 Dur0

K3,K4 8# 1 Qd-Brass-1/4 Fpt-Socket Straight

K3,K4 9# 6” Tube-Blk-3-4 Id X 1 X 100ft

K3,K4,K6 10# 1 Injector Chemical Brass 4500

K1 11# 1 Filter Water In-Line

K3,K4 12# 4 Screw-Shcs-Ss-1/4-20x2x1

K3,K4 13# 1 Coupling-3-8 X 3-8-Brass

K1 14# 5.5” Hose 1/2 Id Wire Reinforced

K3,K4 15# 1 Flare Fitting Fm 90 Deg -6 X

K3,K4 16# 1 Hose Barb 1/2 Hose To 3/8 M

K3,K4 17# 1 Hose-21 In-1-4-Mpt-45-Fem-Flare-6

K5 18# 1 Motor 1/2 HP 120/230V 7.2/3

K1,K3,K4 19# 166USP 5 Hose Clamp-Ss-3/8-7/8

K3,K4 20# 221USP 1 Qd-Plug-Brass-1/4 Mpt-St

K2,K3,K4 21# 1 Unloader Valve For 500 Psi Pum

K1,K3,K4 22# 8.75” Hose 1/2 Id 2 Braid 200 Psi

K3,K4 23# 4” Hose 1/2 Id 2 Braid 200 Psi

K3,K4 24# 1 Bearing & Cam Assembly Size.0

K3,K4 25# 1 Pump Piston Style 300-500 Ps

26# 1 Grommet 3/4 Id X 3/16 Panel

[ ]# 600732888 1 Pump Repair Kit APC-328

K1# 600732877 1 Filterinline With Hoses

K2# 600732875 1 Unloader Valve 400 Psi Tfc-40

K3# 600732865 1 Pump Complete 400psi No Motor

K4# 600732866 1 Pump And Motor Complete 400 PS

K5# 600732868 1 Motor Pump Drive APC328

K6# 600732871 1 Chemical Injector And Metering

# = Revised or new since last update

revised 1/12

5/10 D-7 56041948 - APC328

PARTS LIST

SWITCH PLATE ASSY

revised 1/12

D-8 APC328 - 56041948 5/10

PARTS LIST

SWITCH PLATE ASSY

Kit Item Ref. No. Qty Description

1# 1 Nut Nylon Lock 6/32 Z.P.

2# 6 Tie 4 Black Weather Resis

# 8 Screw-Php-Ss-6x1/2-Sms

K3,K4 4# 2 Hose Barb 90 Deg Nylon 1/8 Mpt

K3 5# 1 Switchplate

K2 6# 1 Switch Rocker Dpst On/Off 20

K1 7# 115USP 2 Washer 1 Od X 9/16 Id X

K2 8# 1 Switch On-Off Illum Clear

K3 9# 1 Gasket-Poron-Switchplate

K1 10# 31USP 2 Washer Brass Half Hard 1 X

K1 11# 45USP 1 Quick Disconnect Plug Male

K3,K4 12# 1 Valve 3-Way For Spotter & Apc

K4 13# 60” Tubing Clear 1/4 Idx 3/8 Od

K4 14# 60” Tubing Clear 1/4 Idx 3/8 Od

K4 15# 21” Tubing Clear 1/4 Idx 3/8 Od

K4 16# 56381203 2 38mm Cap Adapter W Tube

K4 17# 9097023000 2 Adaptor

K1# 56380787 1 Kit Quick Disconnect

K2# 600732885 1 Switch Kit APC-328

K3# 600732886 1 Switch Plate Kit APC-328

K4# 600732882 1 Chem Supply Hoses Jug Caps An

# = Revised or new since last update

revised 1/12

5/10 D-9 56041948 - APC328

PARTS LIST

TANK ASSY

revised 1/12

D-10 APC328 - 56041948 5/10

PARTS LIST

TANK ASSY

Item Ref. No. Qty Description

# 600732884 1 Recovery Tank Complete APC 3 (includes 1-32)

1# 1 Bolt Hex 1/4-20 X 3/4 Full

# 1 Washer 1/4 AN S/S Flat .515

K2 3# 3 Rivet 1/8 Dia Aluminum 1/8 T

4# 6 Nut-Nylon Lock-Ss-8-32

K2,K3 5# 2 Hose Barb Fitting Black Abs

K2 6# 14” Pvc Pipe 11/2 Sch 40

K2 7# 2 Screw H-Low 8 X 3/8 Pa

K4 8# 1 Gasket-Lid-Xlpe-7.15idx.19 Thick

K2 9# 1 Elbow 90 Degree Abs 1-1/2 S

10# 6 Screw-Php-Ss-8-32x1

11# 2 Washer 5/16 Flat Cut Nylon

12# 1 Washer-Fender-1/4 Id-1 Od-Ss

13# 1 Screw 1/4-20 X 3/4 Round He

K3 14# 1 Hose Clamp 3/4 X 1 3/4 Ss

K2 15# 1 Adapter Female 1 1/2

16# 1 Basket Grey 12-1/4 L X 11

K1 17# 1 Hanger-Wire-3/16-Ss

18# 1 Sleeve-Wand-.093 Black Abs-94 Hb

19# 1 Hose Keeper

K3 20# 56262143 1 Vac Hose 1.50 Assy.

K3 21# 56407361 1 Clamp, Plastic

K2 22# 1 Washer-Flat-Buna’n-1-3/4idx0.125

23# 2 Gasket 1.5 X 1.25 X 5.25 A

24# 1 Gasket-0.5 X 1.5 X 8.25

K4 25# 1 LID And RING 6 LID BLACK

K1 26# 2 Cap Black .165 I.D. X 27/16 I

K1 27# 2 Cap .281 I.D. X 1/2 Long In B

28# 2 Bolt-Php-Ss-8-32x1/2

K2 29# 1 Filter S/S Ball Float

30# 1 Vacuum Tank Orca Lt Grey

K2 31# 1 Manifold For Apc

K3 32# 56393772 1 Plug Drain 1 1/2

K1# 600732858 1 Fasteners All Cleaner APC T

K2# 600732874 1 Vacuum Inlet And Filter

K3# 600732846 1 Hoses Drain Priming Vacuum

K4# 600732869 1 Lid And Ring For Vacuum Tank

# = Revised or new since last update

revised 1/12

5/10 D-11 56041948 - APC328

PARTS LIST

10 11

ACCESSORIES

Kit Item Ref. No. Qty Description

TOOLS

1# 61395A 1 Wand Dbl Bend 1/4QC 300 PSI

2# 600732894 1 Wand 2 Piece Alum. Snap Fit

3# 600732895 1 Floor Squeegee Tool 14

4# 600732896 1 Spray Gun Complete

5# 600732854 1 Hose Vac 5/1 Long Cuffs 1.6X25

# 600732893 1 Handle 12 For Hand Squeegee

7# 600732862 1 Squeegee 12 Inch For Use With

# 600732881 1 Tote Maids Gray

9# 600732863 1 Brush Dual Surface With Sque

10# 600732855 1 Pressure Line Complete25 Foot

K1 11# 600752127 1 Priming Hose F/Pump

[ ]# 600732853 1 Metering Tips Kit Two Each Of

[ ]# 600732860 1 Handle Metal Black 54 Inches

Item Ref. No. Qty Description

OPTIONAL ACCESSORIES

12# 56209088 1 Squeegee Assembly 24

12# 56209089 1 30 Squeegee Assy.

13# 56315316 1 Tote Bag

14# 600732901 1 Frame Assembly For Front Moun

[ ]# 600732897 1 Frame Mircoﬁ ber Mop Used Wit

[ ]# 600732898 1 Mop Microﬁ ber 6 Per Kit

[ ]# 600732864 1 Blower Hose And Nozzel Assembl

K1# 600732846 1 Hoses Drain Priming Vacuum

[ ] = Not Shown

# = Revised or new since last update

revised 1/12

D-12 APC328 - 56041948 5/10

PARTS LIST

Page is loading ...

Nilfisk-Advance APC 328 Instructions For Use Manual

Brand: Nilfisk-Advance

Model: APC 328

Category: Floor Machine

Type: Instructions For Use Manual

Download PDF

report

Nilfisk-Advance APC 328 Instructions For Use Manual

Nilfisk-Advance APC 328 Instructions For Use Manual

Related papers

Other documents