T
D
-
80
6
1
3
A
©
M
O
S
M
A
T
A
A
I
C
A
G
06
.
02
.
2
0
12
S
ub
j
b
e
c
t
t
o
c
h
an
g
e
w
i
w
w
t
h
t
t
o
u
t
n
o
t
i
c
e
TUW 520
No. 80.613
A
s
s
s
s
e
m
b
l
y
l
i
n
i
i
s
t
r
t
t
u
r
r
c
t
i
tt
ons
i
i
U
n
d
ercarria
g
e C
l
eaner
For your own safety
- Read all instructions before the initial operation. Check their
proper condition and that they operate safely.
- Always use protection gear when using products connected to
high pressure.
- Before any maintenance or nozzle-change, turn off the high
pressure water supply, e.g.: turn off and secure the
power switch.
- After turning off the system, allow all self propelled equipment
to come to a complete stop before handling.
- Safety regulations and guidelines (Accident Prevention Rules)
from the manufacturer of your high pressure cleaner are
applicable.
- Nozzle installation according to nozzle manufacturer.
- Do not move the unit over objects or uneven surfaces.
- Do not lift up the unit while operating.
- Do not run the unit if spray-arm is out of balance or bent,
damage to the swivel will result.
- No modifications to the unit are permitted.
- The equipment may be installed and used only by particularly
trained technical personnel.
( This instruction is valid for the base model as well as for
the resulting versions)
1. Dismount both wheels (a).
2. Install the lower fork (b) with the bolts (c) with the wheels (a) to
the rack (d).
3. Slide the upper fork (e) over the lower fork (b). Secure the two
forks with the bolt (f) and the safety nut (g).
Note: the handle (h) and the ring (i) point in the same direction.
4. The protection ring (j) and the rotor arm (k) are as factory
installed.
The HP-hose (l) is already connected with the Swivel (m).
5. Connect the HP-gun (n) with the preinstalled adapter (o) to the
quick connect (p).
a
b
cd
e
f
g
h
i
j
k
n
p
o
Accessories
l
m
TUW 520
No. 80.613
TD
-
806
1
3
A
©
M
O
S
M
A
T
A
A
I
C
A
G
06
.
02
.
2
0
12
S
ub
j
b
e
c
t
t
o
c
h
an
g
e
w
i
w
w
t
h
t
t
o
u
t
n
o
t
i
c
e
U
n
d
ercarria
g
e C
l
eane
r
S
p
are
p
arts List
Pos. Part No. Description
1 58.553 Swivel DYF 90°
2 36.905 Carbide seal-kit
3 50.155 Quick-Connect M22-F - G1/4"F
4 900.933 Rubber wheel Dia. 5"
5 903.325 HP-hose G1/4"kM - G1/4"kM
6 50.903 Quick-connect M22-F - G1/4"M
7 51.278 Adaptor M22-M - 1/4"NPT-M
8 29.081 HP-gun 4000 psi
9 14.902 Stabilizer Nozzle
10 18.030EG Insert Nozzle
11 82.891 Turbo-rotor-arm Dia. 18.5"
12 900.932 Stainless steel castor
Accessoires
13 80.621 Guard
1
2
4
5
910
13
12
6
7
8
11
3
/
