Ultra-tow Adjustable Cargo Carrier Owner's manual

Type
Owner's manual
ADJUSTABLE CARGO CARRIER
WITH RAMPS
OWNER’S MANUAL
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS
before operating. Failure to follow the safety rules and other basic safety
precautions may result in serious personal injury.
Item# 14547
Page of 5
2
Thank you very much for choosing an ULTRA-TOWProduct! For future reference, please
complete the owner’s record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to
become familiar with this product before you begin using it.
This product is designed for certain applications only. The distributor cannot be responsible for
issues arising from modification. We strongly recommend this product not be modified and/or used
for any application other than that for which it was designed. If you have any questions relative to a
particular application, DO NOT use this product until you have first contacted the distributor to
determine if it can or should be performed on the product.
For technical questions please call 1-800-222-5381.
Technical Specifications
Platform Size
46in. Long x 34-1/2in. (max.) Wide
Load Weight Capacity
350 lbs.
Required Receiver
2in.
IMPORTANT SAFETY INSTRUCTIONS!
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be followed
to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Keep work area well lighted.
3. Store idle equipment. When not in use, the Cargo Carrier must be stored in a safe and clean
location. Always lock up products and keep out of reach of children.
4. Use the right product for the job. There are certain applications for which the Cargo Carrier was
designed. Do not modify the Cargo Carrier and do not use the Cargo Carrier for a purpose for
which it was not intended.
5. Check for damaged parts. Before using any product, any part that appears damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check
for any broken or damaged parts and any other conditions that may affect its operation. Replace or
repair damaged or worn parts immediately.
6. Replacement parts and accessories. When servicing, use only identical replacement parts. Use
of any other parts will void the warranty.
7. Do not operate product if under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is
any doubt, do not operate the product.
8. Use eye protection. Always wear ANSI-approved impact safety goggles when setting up, loading
and unloading the Cargo Carrier. Wear gloves and avoid sharp edges when assembling and
when loading and unloading the Cargo Carrier.
Page of 5
3
9. Do not allow children to play on, stand upon or climb into the Cargo Carrier. The Cargo
Carrier is not for carrying people or animals.
10. Always check hardware and assembled parts after assembling. All connections should be tight
and hardware tightened.
11. Always distribute objects in the Cargo Carrier evenly. Uneven weight distribution could cause
tipping.
12. Be aware of dynamic loading! Suddenly dropping or bouncing a load on the Cargo Carrier may
create, for a brief instant, an excess load, which may result in damage to the product and/or
personal injury. Additionally, if the vehicle hits a bump, a slight play in the receiving hitch or a
movement in the load could result in a momentary dynamic loading effect that could dramatically
increase the actual weight load. Check the hitch-to-Carrier connection for any looseness. This
momentary dynamic loading effect could result in damage to the Cargo Carrier, the load and
possible personal injury.
WARNING! Be aware of the possible risk of fire and damage to property resulting from the
vehicle’s exhaust system pointing at or running near the cargo put in this Cargo Carrier. Before installing
the Cargo Carrier, check to make sure that the exhaust pipe is not pointing in the direction of the cargo.
Flammable cargo can ignite from exposure to heat. Other cargo can be damaged from the heat. Always
be aware of this potential danger, and never use the Cargo Carrier if the risk exists.
13. Follow DOT guidelines for installation and use.
14. Do not exceed 55 MPH while carrier is attached.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual can not
cover all possible conditions and situations that may occur. It must be understood by the operator that
common sense and caution are factors which cannot be built into this product, but must be supplied by
the operator.
Assembly
It is important that you read the entire manual to become familiar with the product BEFORE you
assemble and use the Cargo Carrier. Before assembling and operating the Cargo Carrier, be
sure that you have all parts described in the Parts List and Assembly Diagram located on the last
pages of this manual.
REFER TO PARTS LISTING PAGE
1. Attach the Stop Plate (2) onto the end of Front Platform (5) by using Bolts (1), Washers (3) and
Lock Nut (4), repeat on Rear Platform (9).
2. Attach Front Platform (5) onto the Support Frame (10) by using Bolts (11), Washer (12) and Lock
Nuts (13); attach Rear Platform (9) onto the Support Frame (10) by using Short Pin (14) and R-pin
(6). Make sure the two Stop Plates are on the same side and side rails on both platforms are face to
face as shown on the Assembly Diagram.
3. Attach the Ramp Head (15) onto the Ramp (8) with Bolt (16) and Lock Nut (4), Slide ramp set into
the channel under Front Platform (5) and Rear Platform (9), and secure with Long Pin (7) and R-pin
(6).
Note: The Ramp set can be assembly in two direction. One is to keep ramp rail upside-A (see
figure in next page), another is to keep ramp rail downside-B (see figure in next page). You
should always attempt ramp rail upside assembly-A when using, this will make your loading safe
and easily by using the ramp rail as a guide. Sometime the mobility you are to load is with very
low off ground height less than rail height, under this situation, you must make sure ramp rail
downside-B to make ramps workable when loading.
Page of 5
4
4. Make sure all bolts and
nuts are tight.
Operation
1. Obtain the assistance
of another adult to help
lift the Cargo Carrier.
2. Lift the Cargo Carrier
and place the 2in.
Square Tube End on
Support Frame (10)
into the 2in. Hitch
Receiver mounted to
your vehicle.
3. Line up the hole in the
2in. Square Tube End
with the hole in your
hitch, slide a 5/8in.
Hitch Pin (not included)
through the holes and insert a Lock Pin (not included) to hold in place.
4. Remove the Short Pins (14) and R-pins (6) and adjust to the desired width, then replace the Short
Pins (14) and R-pins (6).
5. Remove Long Pins (7) and R-pin (6) and pull ramps out from the channel under Front Platform (5)
and Rear Platform (9), then hook onto the end of Front Platform (5) and Rear Platform (9).
Note: The Ramp set can be used in two direction. One is to keep ramp rail upside, another is to
keep ramp rail downside. You should always attempt ramp rail upside when using, this will make
your loading safe and easily by using the ramp rail as a guide. Sometime the mobility you are to
load is with very low off ground height less than rail height, under this situation, you must make
sure ramp rail downside to make ramps workable when loading. You also must be very careful
and slowly when loading to keep mobility wheels on center of the ramps. (see above figure)
6. Load equipment onto Carrier using included Ramps.
WARNING: Don’t exceed the rated capacity, load the equipment carefully and slowly, make sure
the wheels are always on center of the ramps and platform when loading.
7. Slide Ramps back into storage position and secure with Long Pins (7) and R-pin (6)
8. Secure the equipment to Platforms with enough tie-down straps (not provided) before
transportation.
9. Reverse above procedures for unloading equipment.
WARNING: The load weight must be centered or evenly distributed across the Carrier platform.
Always use appropriate tie-down restraints to securely attach any cargo loaded onto the Cargo Carrier
before moving your vehicle any distance. Do not leave loose items on the platform while operating the
vehicle. Always use Reflectors. Make certain to use the appropriate red flags when moving a load.
Check with your local traffic enforcement agency to make certain that you are correctly following all local
laws.
Page of 5
5
Parts and Assembly Diagram
Part
Description
Qty
Part
Description
Qty
1
Bolt
4
10
Support Frame
1
2
Stop Plate
2
11
Bolt
2
3
Washer
4
12
Washer
2
4
Lock Nut
4
13
Lock Nut
2
5
Front Platform
1
14
Short Pin
2
6
R-pin
6
15
Ramp Head
2
7
Long Pin
4
16
Bolt
4
8
Ramp
2
17
Lock Nut
4
9
Rear Platform
1
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Distributed by
Northern Tool + Equipment Co., Inc.
Burnsville, Minnesota 55306-6936
Made in CHINA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Ultra-tow Adjustable Cargo Carrier Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI