Pack 01
MOTORCYCLE
™
Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP.
Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE.
Published in the USA by De Agostini Publishing USA, Inc.,121 E. Calhoun Street, Woodstock, IL 60098.
All rights reserved © 2018
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
MOTORCYCLE
1The fuel tank 3
2The front wheel and mirror 5
3The headlight 6
™
3
STEP-BY-STEP ASSEMBLY
MOTORCYCLE
Build the
from ™
The parts supplied in this first stage
of Pack 1 indicate the quality of the
finished model. Paint, decals and
chromium plating are already applied.
A. Petrol tank
B. Front bracket
C. Rear bracket
D. Fixing screws (x 3)
E. Filler cap
STEP 1 The blue front bracket has a crank in the
middle and one end is more curved than the other
(shown in inset). Fit it this way round, as shown.
STEP 2 Use the tip of a crosshead screwdriver to
pick up one of the screws provided.
STAGE 1: THE FUEL TANK
YOUR PARTS
STEP3
STEP1STEP2
A B C D E
STEP 3 Screw the bracket to the mounting
hole in the tank.
STEP 4 The red rear bracket ts this way round
(shown in inset), with the straight end facing the tank.
STEP4
4
MOTORCYCLE
Build the
from ™
Stage complete
You have now
completed this stage
of assembly. Keep
your assembled tank
safe until it is time to t
it to the motorcycle.
STEP7
STEP5STEP6
STEP 5 Use another screw to x the red bracket to
the mounting hole in the tank.
STEP 6 The two brackets should look like this.
STEP8
STEP 7 The ller cap has a bayonet tting, with two
lugs that t into two notches on the tank ller.
STEP 8 Fit the cap to the tank, and give it a quarter
turn to secure it.
5
STEP-BY-STEP ASSEMBLY
In this stage, you have received the
parts for the front wheel and mirror.
You can t the tyre to the wheel now,
but keep the mirror and its ttings until
a later stage.
A. Front wheel
B. Handlebar mirror
C. Handlebar clamp
D. Washer
E. Fixing nut
Stage complete
The nished
front wheel
should
look like
this.
STEP1
STAGE 2: THE FRONT WHEEL AND MIRROR
YOUR PARTS
STEP 1 Take the wheel together with
the tyre from the third stage.
STEP2
STEP3
A B
C D E
STEP 2 Ease the solid rim of the wheel
into the well in the centre of the tyre.
STEP 3 Work your way around the wheel, easing
the tyre over the rim as you go.
6
MOTORCYCLE
Build the
from ™
STAGE 3: THE HEADLIGHT
YOUR PARTS
The parts received here include a working LED and its wiring, pre-installed inside the headlight shell.
A. Headlight rim
B. Headlight glass
C. Headlight reector
D. Headlight shell
E. Right-hand bracket
F. Left-hand bracket
G. Fixing screws (x 3)
H. T-bar spanner
I. Front tyre (Used in Stage 2)
A B C
D
E F
G
H
I
STEP 1 Take the headlight glass.
Its markings are not symmetrical,
and it goes this way up. Note the
different-sized notches on the left
and right.
STEP 2 The headlight rim has two
small lugs on the inside that match
the notches on the glass.
STEP1STEP2
STEP 3 The outside of the rim
has this clamp detail moulded in
at one point. This will go at the
bottom of the nished headlight.
STEP3
7
STEP-BY-STEP ASSEMBLY
STAGE 3: THE HEADLIGHT STEP4STEP5
STEP 8 The headlight shell has two large tangs
(arrowed), which t into matching recesses in the
rim. It doesn’t matter which way up these go.
STEP 9 Fit the rim over the two tangs, and give it a
slight twist in the direction of the arrow to lock the
headlight assembly onto the shell.
STEP 4 Fit the glass into the rim, with the glass
curving outwards. Make sure that the notches and
lugs shown in Steps 1 and 2 line up with each other.
STEP 5 Ensure that the lugs go into the notches so
that the glass ts ush.
STEP 6 The headlight reector has two notches in
the rim that match the notches in the glass.
STEP 7 Line up the notches in the reector with the
lugs on the rim, in the same way you did with the
glass in Step 4, and press it all the way into the rim.
STEP6STEP7
STEP8STEP9
8
MOTORCYCLE
Build the
from ™
STEP 14 Take the left-hand bracket and t it in the
same way as in Steps 10–13.
STEP 13 Use the T-bar spanner provided to tighten
the screw rmly.
STEP 11 Line up the mounting holes on the bracket
and the headlight shell.
STEP 10 Holding the light with the clamp from Step
3 on top, align the right-hand bracket this way up.
STEP 12 Take one of the xing screws and t it into
the hole. Screw it in nger-tight.
Stage
complete
The headlight
should look
like this, with
the rim clamp
at the bottom.
STEP11
STEP12 STEP13
STEP14
STEP10
/