Bosch GOF 1300 CE Professional Owner's manual

Page is loading ...

3 |

1 609 929 N93 | (2.9.08) Bosch Power Tools

GOF 1300 CE

Professional

17

18

19

20

16

15

14

13

12

11

10

9

1

24

8

1

17

21

22

23

5

8

2

3

4

5

6

7

OBJ_BUCH-203-003.book Page 3 Tuesday, September 2, 2008 8:46 AM

4 |

1 609 929 N93 | (2.9.08) Bosch Power Tools

FE

DC

BA

23

4

25

26

27

28

6

18

16

15

14

11

10

7

OBJ_BUCH-203-003.book Page 4 Tuesday, September 2, 2008 8:46 AM

5 |

1 609 929 N93 | (2.9.08) Bosch Power Tools

ML

K

4342

36

I

H

31

G

32

29

33

34

35

30

5

41

37

36

38 39 40

45

44

47

46

9

47

OBJ_BUCH-203-003.book Page 5 Tuesday, September 2, 2008 8:46 AM

6 |

1 609 929 N93 | (2.9.08) Bosch Power Tools

N

49 5048 9

OBJ_BUCH-203-003.book Page 6 Tuesday, September 2, 2008 8:46 AM

Page is loading ...

English | 19

Bosch Power Tools 1 609 929 N93 | (2.9.08)

en

Safety Notes

General Power Tool Safety Warnings

Read all safety warnings and all

instructions. Failure to follow

the warnings and instructions may result in elec-

tric shock, fire and/or serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers to

your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified

plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes, radia-

tors, ranges and refrigerators. There is

an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges and moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric

shock.

f) If operating a power tool in a damp loca-

tion is unavoidable, use a residual cur-

rent device (RCD) protected supply. Use

of an RCD reduces the risk of electric

shock.

3) Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool

while you are tired or under the influ-

ence of drugs, alcohol or medication. A

moment of inattention while operating

power tools may result in serious person-

al injury.

b) Use personal protective equipment. Al-

ways wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protec-

tion used for appropriate conditions will

reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your fin-

ger on the switch or energising power

tools that have the switch on invites acci-

dents.

d) Remove any adjusting key or wrench be-

fore turning the power tool on. A wrench

or a key left attached to a rotating part of

the power tool may result in personal inju-

ry.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unex-

pected situations.

f) Dress properly. Do not wear loose cloth-

ing or jewellery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewellery or long hair can

be caught in moving parts.

WARNING

OBJ_BUCH-203-003.book Page 19 Tuesday, September 2, 2008 8:46 AM

20 | English

1 609 929 N93 | (2.9.08) Bosch Power Tools

g) If devices are provided for the connec-

tion of dust extraction and collection fa-

cilities, ensure these are connected and

properly used. Use of dust collection can

reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job better

and safer at the rate for which it was de-

signed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the

switch is dangerous and must be re-

paired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these in-

structions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tool’s op-

eration. If damaged, have the power tool

repaired before use. Many accidents are

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp

cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool

bits etc. in accordance with these in-

structions, taking into account the work-

ing conditions and the work to be per-

formed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qual-

ified repair person using only identical

replacement parts. This will ensure that

the safety of the power tool is maintained.

Safety Warnings for Routers

f The allowable speed of the router bit must

be at least as high as the maximum speed

listed on the power tool. Accessories that

rotate faster than permitted can be de-

stroyed.

f Router bits or other accessories must fit ex-

actly in the tool holder (collet) of your ma-

chine. Routing bits that do not fit precisely in

the tool holder of the machine rotate irregu-

larly, vibrate heavily and can lead to loss of

control.

f Apply the machine to the workpiece only

when switched on. Otherwise there is dan-

ger of kickback when the cutting tool jams in

the workpiece.

f Keep your hands away from the cutting area

and the cutting disc. Hold the auxiliary han-

dle with your second hand. When both

hands hold the machine, they cannot be in-

jured by the cutting disc.

f Never cut over metal objects, nails or

screws. The router bit can become damaged

and lead to increased vibrations.

f Hold the power tool only by the insulated

gripping surfaces when performing an oper-

ation where the cutting tool may contact

hidden wiring or its own cord. Contact with

a “live” wire will also make exposed metal

parts of the power tool “live” and shock the

operator.

f Use appropriate detectors to determine if

utility lines are hidden in the work area or

call the local utility company for assistance.

Contact with electric lines can lead to fire

and electric shock. Damaging a gas line can

lead to explosion. Penetrating a water line

causes property damage or may cause an

electric shock.

OBJ_BUCH-203-003.book Page 20 Tuesday, September 2, 2008 8:46 AM

English | 21

Bosch Power Tools 1 609 929 N93 | (2.9.08)

f Do not use blunt or damaged router bits.

Blunt or damaged router bits cause in-

creased friction, can become jammed and

lead to imbalance.

f When working with the machine, always

hold it firmly with both hands and provide

for a secure stance. The power tool is guided

more secure with both hands.

f Secure the workpiece. A workpiece clamped

with clamping devices or in a vice is held

more secure than by hand.

f Keep your workplace clean. Blends of mate-

rials are particularly dangerous. Dust from

light alloys can burn or explode.

f Always wait until the machine has come to

a complete stop before placing it down. The

tool insert can jam and lead to loss of control

over the power tool.

f Never use the machine with a damaged ca-

ble. Do not touch the damaged cable and

pull the mains plug when the cable is dam-

aged while working. Damaged cables in-

crease the risk of an electric shock.

Functional Description

Read all safety warnings and all in-

structions. Failure to follow the

warnings and instructions may re-

sult in electric shock, fire and/or se-

rious injury.

While reading the operating instructions, unfold

the graphics page for the machine and leave it

open.

Intended Use

The machine is intended for routing grooves,

edges, profiles and elongated holes as well as

for copy routing in wood, plastic and light build-

ing materials, while resting firmly on the work-

piece.

With reduced speed and with appropriate rout-

ing bits, non-ferrous alloys can also be ma-

chined.

Product Features

The numbering of the product features refers to

the illustration of the machine on the graphics

page.

1 Right handle

2 Lock-on button for On/Off switch

3 Thumbwheel for speed preselection

4 Spindle lock lever

5 Wing bolt for guide rods of parallel guide

(2x)*

6 Chip shield

7 Router bit*

8 Seat for parallel guide rods

9 Guide plate

10 Step buffer

11 Adjusting screws for step buffer

12 Base plate

13 Dust boot

14 Wing bolt for depth stop adjustment

15 Depth stop

16 Slide with index mark

17 Left handle

18 Scale for depth-of-cut

19 Scale for depth-of-cut fine adjustment

20 Adjustment knob for depth-of-cut fine ad-

justment

21 Mark for zeroing

22 Release lever

23 Tightening nut with collet

24 On/Off switch

25 Open-end spanner, size 24 mm*

26 Extraction hose (Ø 35 mm)*

27 Extraction adapter*

28 Knurled screw for extraction adapter (2x)*

29 Parallel guide*

30 Guide rod for parallel guide (2x)*

31 Wing bolt for fine adjustment of parallel

guide (2x)*

32 Wing bolt for coarse adjustment of

parallel guide (2x)*

33 Fine-adjustment knob for parallel guide*

34 Edge guide for parallel guide*

OBJ_BUCH-203-003.book Page 21 Tuesday, September 2, 2008 8:46 AM

22 | English

1 609 929 N93 | (2.9.08) Bosch Power Tools

35 Extraction adapter for parallel guide*

36 Router compass/guide-rail adapter*

37 Router compass handle*

38 Wing bolt for coarse adjustment of

router compass (2x)*

39 Wing bolt for fine adjustment of

router compass (1x)*

40 Fine-adjustment knob for router compass*

41 Centring screw*

42 Base spacer

(included in the “router compass” set)*

43 Guide rail*

44 Guide bushing adapter

45 Fastening screw for guide bushing adapter

(2x)

46 Release lever for guide bushing adapter

47 Guide bushing

48 Pan head screw for guide plate

49 Countersunk head screw for guide plate

50 Centring pin

*The accessories illustrated or described are not in-

cluded as standard delivery.

Technical Data

Noise/Vibration Information

Measured values determined according to

EN 60745 (chip board).

Typically the A-weighted noise levels of the

product are: Sound pressure level 89 dB(A);

Sound power level 100 dB(A). Uncertainty

K=3dB.

Wear hearing protection!

Vibration total values (triax vector sum) deter-

mined according to EN 60745:

Vibration emission value a

h

=5.5 m/s

2

, Uncer-

tainty K =2.5 m/s

2

.

The vibration emission level given in this infor-

mation sheet has been measured in accordance

with a standardised test given in EN 60745 and

may be used to compare one tool with another.

It may be used for a preliminary assessment of

exposure.

The declared vibration emission level repre-

sents the main applications of the tool. However

if the tool is used for different applications, with

different accessories or poorly maintained, the

vibration emission may differ. This may signifi-

cantly increase the exposure level over the total

working period.

Plunge router GOF 900 CE

Professional

GOF 1300 CE

Professional

Article number

0 601 614 6.. 0 601 613 6..

Rated power input

W 900 1300

No-load speed

min

-1

12000 – 24000 12000 – 24000

Speed preselection

z z

Constant electronic control

z z

Connection for dust extraction

z z

Tool holder

mm

inch

6–8

¼

6–12.7

¼–½

Plunge depth

mm 50 58

Weight according to EPTA-Procedure 01/2003

kg 3.5 4.8

Protection class

/II /II

The values given are valid for nominal voltages [U] of 230/240 V. For lower voltage and models for specific countries,

these values can vary.

Please observe the article number on the type plate of your machine. The trade names of the individual machines

may vary.

OBJ_BUCH-203-003.book Page 22 Tuesday, September 2, 2008 8:46 AM

English | 23

Bosch Power Tools 1 609 929 N93 | (2.9.08)

An estimation of the level of exposure to vibra-

tion should also take into account the times

when the tool is switched off or when it is run-

ning but not actually doing the job. This may sig-

nificantly reduce the exposure level over the to-

tal working period.

Identify additional safety measures to protect

the operator from the effects of vibration such

as: maintain the tool and the accessories, keep

the hands warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that

the product described under “Technical Data” is

in conformity with the following standards or

standardization documents: EN 60745 accord-

ing to the provisions of the directives

2004/108/EC, 98/37/EC (until 28 Dec 2009),

2006/42/EC (from 29 Dec 2009).

Technical file at:

Robert Bosch GmbH, PT/ESC,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

31.07.2008

Assembly

Inserting a Router Bit (see figure A)

f Before any work on the machine itself, pull

the mains plug.

f It is recommended to wear protective

gloves when inserting or replacing router

bits.

Depending on the application, router bits are

available in the most different designs and qual-

ities.

Router bits made of high speed steel (HSS) are

suitable for the machining of soft materials, e. g.

softwood and plastic.

Carbide tipped router bits (HM) are particular-

ly suitable for hard and abrasive materials, e. g.

hardwood and aluminium.

Original router bits from the extensive Bosch ac-

cessories program are available at your special-

ist shop.

Only use clean router bits that are in perfect

condition.

– Fold the chip shield 6 down.

– Push the spindle lock lever 4 in clockwise di-

rection and hold it in this position (n). If re-

quired, turn the motor spindle by hand until

it is locked.

– Loosen the tightening nut 23 with the open-

end spanner 25 (size 24 mm) by turning in

antclockwise direction (o).

– Insert the router bit into the collet. The shank

of the router bit must be immersed at least

20 mm into the collet.

– Tighten the tightening nut 23 with the open-

end spanner 25 (size 24 mm) by turning in

clockwise direction. Release the spindle lock

lever 4.

– Fold the chip shield 6 up again.

f Do not insert a router bit with a diameter

larger than 50 mm when the guide bushing

is not mounted. Such router bits do not fit

through the base plate.

f Do not tighten the tightening nut of the col-

let without a router bit inserted. Otherwise

the collet can be damaged.

Dust/Chip Extraction (see figure B)

f Dusts from materials such as lead-containing

coatings, some wood types, minerals and

metal can be harmful to one’s health. Touch-

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

tions of the user or bystanders.

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

OBJ_BUCH-203-003.book Page 23 Tuesday, September 2, 2008 8:46 AM

24 | English

1 609 929 N93 | (2.9.08) Bosch Power Tools

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

– Use dust extraction whenever possible.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Mounting the Extraction Adapter

The extraction adapter 27 can be mounted with

the hose connection to the front or to the rear.

When the guide bushing adapter 44 is mounted,

it is possible that the guide bushing adapter

must be turned by 180° so that the extraction

adapter 27 does not touch the release lever 46.

When mounting with the hose connection in

front, the chip shield 6 must be removed first.

Fasten the extraction adapter 27 with the

2 knurled screws 28 to the base plate 12.

Connecting the Dust Extraction

Insert an extraction hose (Ø 35 mm) 26 (acces-

sory) into the mounted extraction adapter. Con-

nect the extraction hose 26 to a vacuum cleaner

(accessory).

The machine can be plugged directly into the re-

ceptacle of a Bosch all-purpose vacuum cleaner

with remote starting control. The vacuum clean-

er starts automatically when the machine is

switched on.

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Mounting the Chip Shield (see figure C)

Insert the chip shield 6 from the front into the

guide in such a manner that it engages. To re-

move the chip shield, grasp it by the sides and

pull it off toward the front.

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Preselecting the Speed

The required speed can be preselected with the

thumbwheel 3 (also while running).

1 – 2 low speed

3 – 4 medium speed

5–6 high speed

The values shown in the chart are standard val-

ues. The necessary speed depends on the mate-

rial and the operating conditions, and can be de-

termined by practical testing.

After longer periods of working at low speed, al-

low the machine to cool down by running it for

approx. 3 minutes at maximum speed with no

load.

Material Router bit di-

ameter (mm)

Thumb-

wheel 3

Hardwood (Beech)

4–10

12 – 20

22 – 40

5–6

3–4

1–2

Softwood (Pine)

4–10

12 – 20

22 – 40

5–6

3–6

1–3

Particle Board

4–10

12 – 20

22 – 40

3–6

2–4

1–3

Plastics

4–15

16 – 40

2–3

1–2

Aluminium

4–15

16 – 40

1–2

1

OBJ_BUCH-203-003.book Page 24 Tuesday, September 2, 2008 8:46 AM

English | 25

Bosch Power Tools 1 609 929 N93 | (2.9.08)

Switching On and Off

Adjust the depth-of-cut before switching on or

off; see Section “Adjusting the Depth-of-cut”.

To start the machine, press the On/Off switch

24 and keep it pressed.

To lock the pressed On/Off switch 24, press the

lock-on button 2.

To switch off the machine, release the On/Off

switch 24 or when it is locked with the lock-on

button 2, briefly press the On/Off switch 24 and

then release it.

Constant Electronic Control

Constant electronic control holds the speed

constant at no-load and under load, and ensures

uniform working performance.

Soft Starting

The electronic soft starting feature limits the

torque upon switching on and increases the

working life of the motor.

Adjusting the Depth-of-cut

(see figure D)

f The adjustment of the depth-of-cut may on-

ly be carried out when the router is

switched off.

For coarse adjustment of the depth-of-cut, pro-

ceed as follows:

– Place the machine with the router bit mount-

ed on the workpiece to be machined.

– Set the fine-adjustment path to the centre

position with the adjustment knob 20. For

this, turn the adjustment knob 20 until the

marks 21 match as shown in the figure. After-

wards, set the scale 19 to “0”.

– Set the step buffer 10 to the lowest position;

the step buffer engages noticeably.

– Loosen the wing bolt for the depth stop 14

so that the depth stop 15 can be moved free-

ly.

– Push the release lever 22 downward and

slowly lower the plunge router until the rout-

er bit 7 touches the surface of the workpiece.

Let go of the release lever 22 again to lock

this plunging depth.

– Push the depth stop 15 downward until it

rests on the step buffer 10. Set the slide with

the index mark 16 to the “0” position on the

scale for the depth-of-cut adjustment 18.

– Set the depth stop 15 to the required depth-

of-cut and tighten the wing bolt for the depth

stop 14. Pay attention not to misadjust the

slide with the index mark 16 again.

– Push the release lever 22 and guide the

plunge router to the uppermost position.

For deep cuts, it is recommended to carry out

several cuts, each with little material removal.

By using the step buffer 10, the cutting process

can be divided into several steps. For this, ad-

just the desired depth-of-cut with the lowest

step of the step buffer and select the higher

steps first for the initial cuts. The clearance of

the steps can be changed by screwing the ad-

justing screws 11 further in or out.

After a trial cut, the depth-of-cut can be set ex-

actly to the desired measure by turning the ad-

justment knob 20; turn in clockwise direction to

increase the cutting depth and in anticlockwise

direction to decrease the cutting depth. The

scale 19 can be used for guidance. One full turn

corresponds with a setting range of 2.0 mm; a

graduation mark on the top edge of the scale 19

corresponds with a 0.1 mm change of the set-

ting range. The maximum setting range is

± 8mm.

Example: The desired depth-of-cut is to be

10.0 mm; the trial cut resulted in a cutting depth

of 9.6 mm.

– Lift up the router and place e. g. a piece of

scrap wood under the guide plate 9 so that

the router bit 7 cannot touch the workpiece

when lowering it. Push the release lever 22

down and slowly lower the plunge router un-

til the depth stop 15 faces on the step buffer

10.

–Turn the scale 19 to “0” and loosen wing bolt

14.

21

OBJ_BUCH-203-003.book Page 25 Tuesday, September 2, 2008 8:46 AM

26 | English

1 609 929 N93 | (2.9.08) Bosch Power Tools

– Turn the adjustment knob 20 by 0.4 mm/4

graduation marks (difference from set to ac-

tual value) in clockwise direction and tighten

the wing bolt 14.

– Check the selected depth-of-cut by carrying

out another trial cut.

After adjusting the depth-of-cut, do not change

the position of the slide 16 on the depth stop 15

any more, so that the actual cutting depth can

be read on the scale 18.

Working Advice

f Protect router bits against shock and im-

pact.

Direction of Feed and Routing Process

(see figure E)

f The routing process must always be carried

out against the rotation direction of the

router bit 7 (up-cutting motion). When rout-

ing in the direction with the rotation of the

router (down-cutting), the machine can

break loose, eliminating control by the user.

– Adjust the required depth-of-cut; see Section

“Adjusting the Depth-of-cut”.

– Place the machine with the router bit mount-

ed on the workpiece to be machined and

switch the power tool on.

– Push the release lever 22 down and slowly

lower the plunge router until the adjusted

depth-of-cut is reached. Let go of the release

lever 22 again to lock this cutting depth.

– Carry out the routing process applying uni-

form feed.

– After finishing the cutting process, guide the

plunge router upward again to the upper-

most position.

– Switch the power tool off.

Routing with Auxiliary Guide (see figure F)

For working large workpieces, e. g. when rout-

ing grooves, a board or wood strip can be fas-

tened to the workpiece as an auxiliary guide

alongside which the router can be guided. Guide

the router with the flattened side of the guide

plate along the auxiliary guide.

Shaping or Molding Applications

For shaping or molding applications without the

use of a parallel guide, the router bit must be

equipped with a pilot or a ball bearing.

– Guide the switched on power tool from the

side toward the workpiece until the pilot or

the ball bearing of the router bit faces

against the workpiece edge to be machined.

– Guide the power tool alongside the work-

piece edge with both hands, paying attention

that the router is positioned rectangular. Too

much pressure can damage the edge of the

workpiece.

Routing with Parallel Guide (see figure G)

Slide the parallel guide 29 with the guide rods

30 into the base plate 12 and tighten as required

with the wing bolts 5. Additionally, the parallel

guide can be adjusted lengthwise with the wing

bolts 31 and 32.

Fine adjustment of the length is possible with

the fine-adjustment knob 33 after loosening

both wing bolts 31. One revolution corresponds

with a setting range of 2.0 mm. One graduation

mark on the fine-adjustment knob 33 changes

the setting range by 0.1 mm.

The effective contact surface of the parallel

guide can be adjusted with the edge guide 34.

Guide the switched on power tool with uniform

feed and lateral pressure on the parallel guide

alongside the workpiece edge.

When routing with the parallel guide 29, the

dust/chip extraction should take place via the

special extraction adapter for the parallel guide

35. The extraction adapter 27 can remain

mounted.

Routing with the Router Compass

(see figure H)

The router compass/guide-rail adapter 36 can

be used for circular routing jobs. Mount the

router compass as shown in the figure.

Screw the centring screw 41 into the thread on

the router compass. Insert the point of the cen-

tring screw into the centre of the circular arc to

be routed, paying attention that point of the

screw engages into the workpiece surface.

OBJ_BUCH-203-003.book Page 26 Tuesday, September 2, 2008 8:46 AM

English | 27

Bosch Power Tools 1 609 929 N93 | (2.9.08)

Coarsely adjust the required radius by moving

the router compass and tighten the wing bolts

38 and 39.

The length can be fine adjusted with the fine-ad-

justment knob 40 after loosening the wing bolt

39. One revolution corresponds with a setting

range of 2.0 mm. One graduation mark on the

fine-adjustment knob 40 changes the setting

range by 0.1 mm.

Guide the switched on power tool over the

workpiece with the right handle 1 and the router

compass handle 37.

Routing with Guide Rail (see figure I)

Straight routing cuts can be carried out with

help of the guide rail 43.

The base spacer 42 must be mounted in order to

compensate the height difference.

Mount the router compass/guide-rail adapter 36

as shown in the figure.

Fasten the guide rail 43 to the workpiece with

suitable clamping devices, e. g. screw clamps.

Place the machine with the guide-rail adapter 36

mounted onto the guide rail.

Routing with Guide Bushing (see figures K–N)

The guide bushing 47 enables template and pat-

tern routing on workpieces.

In order to use the guide bushing 47, the guide

bushing adapter 44 must be inserted into the

guide plate 9 first.

Place the guide bushing adapter 44 from above

onto the guide plate 9 and tighten it firmly with

the 2 fastening screws 45. Pay attention that

the release lever for the guide bushing adapter

46 is freely movable.

Choose a suitable guide bushing, depending on

the thickness of the template or the pattern. Be-

cause of the projecting height of the guide bush-

ing, the template must have a minimum thick-

ness of 8 mm.

Actuate the release lever 46 and insert the guide

bushing 47 from below into the guide bushing

adapter 44. Ensure that the encoding keys clear-

ly engage in the grooves of the guide bushing.

f Select a router bit with a diameter smaller

than the interior diameter of the guide

bushing.

To ensure that the distance from router bit cen-

tre and guide bushing edge is uniform, the guide

bushing and the guide plate can be adjusted to

each other, if required.

– Push the release lever 22 down and guide the

router to the stop in the direction of the base

plate 12. Let go of the release lever 22

again,

in order to lock this plunging depth.

– Unscrew the countersunk head screws 49.

Screw the pan head screws 48 into the holes

intended for this purpose in such a manner

that the guide plate 9 can be moved freely.

– Insert the centring pin 50 into the tool holder

as shown in the figure. Hand-tighten the

tightening nut so that the centring pin can

still be moved freely.

– Align the centring pin 50 and the guide bush-

ing 47 to each other by slightly moving the

guide plate 9.

– Tighten the pan head screws 48.

– Remove the centring pin 50 from the tool

holder.

– Push the release lever 22 and guide the

plunge router to the uppermost position.

For routing with the guide bushing 47 proceed

as follows:

– Guide the switched on power tool with the

guide bushing toward the template.

– Push the release lever 22 down and slowly

lower the plunge router until the adjusted

depth-of-cut is reached. Let go of the release

lever 22 again to lock this cutting depth.

– Guide the switched on power tool with the

protruding guide bushing alongside the tem-

plate applying lateral pressure.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

OBJ_BUCH-203-003.book Page 27 Tuesday, September 2, 2008 8:46 AM

28 | English

1 609 929 N93 | (2.9.08) Bosch Power Tools

f In extreme working conditions, conductive

dust can accumulate in the interior of the

machine when working with metal. The pro-

tective insulation of the machine can be de-

graded. The use of a stationary extraction

system is recommended in such cases as

well as frequently blowing out the ventila-

tion slots and installing a residual current

device (RCD).

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article

number given on the type plate of the machine.

WARNING! Important instructions for con-

necting a new 3-pin plug to the 2-wire cable.

The wires in the cable are coloured according to

the following code:

Do not connect the blue or brown wire to the

earth terminal of the plug.

Important: If for any reason the moulded plug is

removed from the cable of this power tool, it

must be disposed of safely.

After-sales Service and Customer As-

sistance

Our after-sales service responds to your ques-

tions concerning maintenance and repair of your

product as well as spare parts. Exploded views

and information on spare parts can also be

found under:

www.bosch-pt.com

Our customer consultants answer your ques-

tions concerning best buy, application and ad-

justment of products and accessories.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB 9 5HJ

Tel. Service: +44 (0844) 736 0109

Fax: +44 (0844) 736 0146

E-Mail: SPT-Tec[email protected]sch.com

Ireland

Origo Ltd.

Unit 23 Magna Drive

Magna Business Park

City West

Dublin 24

Tel. Service: +353 (01) 4 66 67 00

Fax: +353 (01) 4 66 68 88

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.

Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center

Inside Australia:

Phone: +61 (01300) 307 044

Fax: +61 (01300) 307 045

Inside New Zealand:

Phone: +64 (0800) 543 353

Fax: +64 (0800) 428 570

Outside AU and NZ:

Phone: +61 (03) 9541 5555

www.bosch.com.au

Disposal

The machine, accessories and packaging should

be sorted for environmental-friendly recycling.

Only for EC countries:

Do not dispose of power tools in-

to household waste!

According the European Guideline

2002/96/EC for Waste Electrical

and Electronic Equipment and its

implementation into national right, power tools

that are no longer usable must be collected sep-

arately and disposed of in an environmentally

correct manner.

Subject to change without notice.

OBJ_BUCH-203-003.book Page 28 Tuesday, September 2, 2008 8:46 AM

Page is loading ...

296 |

1 609 929 N93 | (2.9.08) Bosch Power Tools

6 mm 2 608 570 103

1/4" 2 608 570 104

8 mm 2 608 570 105

10 mm 2 608 570 125

3/8" 2 608 570 106

12 mm 2 608 570 107

1/2" 2 608 570 108

10,8 mm 2 609 200 282

13 mm 2 609 200 138

13,8 mm 2 609 200 283

17 mm 2 609 200 139

24 mm 2 609 200 140

27 mm 2 609 200 141

30 mm 2 609 200 142

40 mm 2 609 200 312

8 mm 2 609 200 310

12 mm 2 609 200 311

1/4" 2 609 200 317

1/2" 2 609 200 318

2 608 190 038

GOF 1300 CE

2 608 570 100

2 608 570 101

2 608 570 102

GOF 900 CE

OBJ_BUCH-203-003.book Page 296 Tuesday, September 2, 2008 8:46 AM

| 297

Bosch Power Tools 1 609 929 N93 | (2.9.08)

2 609 200 145 (L = 0,8 m)

2 607 001 387

2 609 200 143

2 602 317 030 (L = 0,7 m)

2 602 317 031 (L = 1,4 m)

Ø 35 mm

3 m 2 609 390 392

5 m 2 609 390 393

GAS 25/50/50 M

Ø 35 mm

3 m 2 607 002 163

5 m 2 607 002 164

GAS 25/50/50 M

OBJ_BUCH-203-003.book Page 297 Tuesday, September 2, 2008 8:46 AM

Bosch GOF 1300 CE Professional Owner's manual

This manual is also suitable for

Bosch GOF 1300 CE Professional Owner's manual

in other languages

Related papers

Other documents