PCM43102X
User Manual
Microwave combi-oven
CONTENTS
Safety information 2
Safety instructions 5
Product description 7
Control panel 8
Before first use 10
Daily use 10
Microwave mode 12
Clock functions 14
Automatic programmes 15
Using the accessories 16
Additional functions 17
Hints and tips 18
Care and cleaning 39
Troubleshooting 40
Subject to change without notice.
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair
information:
www.progress-hausgeraete.de/support
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damage that are the result of
incorrect installation or usage. Always keep the instructions
in a safe and accessible location for future reference.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
• Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.
• Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.
• Do not let children play with the appliance.
• Keep all packaging away from children and dispose of it
appropriately.
2 Progress
• Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts may
become hot during use.
• If the appliance has a child safety device, it should be
activated.
• Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
• Only a qualified person must install this appliance and
replace the cable.
• WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to avoid
touching heating elements.
• Always use oven gloves to remove or put in accessories or
ovenware.
• Before carrying out any maintenance, disconnect the
appliance from the power supply.
• WARNING: Ensure that the appliance is switched off
before replacing the lamp to avoid the possibility of electric
shock.
• Do not use the appliance before installing it in the built-in
structure.
• Do not use a steam cleaner to clean the appliance.
• Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the glass door since they can scratch the
surface, which may result in shattering of the glass.
• If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service
Centre or similarly qualified persons to avoid an electrical
hazard.
• Do not activate the appliance when it is empty. Metal parts
inside the cavity can create electric arcing.
• Metallic containers for food and beverages are not allowed
during microwave cooking. This requirement is not
applicable if the manufacturer specifies size and shape of
metallic containers suitable for microwave cooking.
Progress 3
• If the door or door seals are damaged, the appliance must
not be operated until it has been repaired by a qualified
person.
• Only a qualified person can carry out any service or repair
operation that involves the removal of a cover which gives
protection against exposure to microwave energy.
• Do not heat liquids and other foods in sealed containers.
They are liable to explode.
• Use only utensils that are suitable for use in microwave
ovens.
• When heating food in plastic or paper containers, keep an
eye on the appliance due to the possibility of ignition.
• The appliance is intended for heating food and beverages.
Drying of food or clothing and heating of warming pads,
slippers, sponges, damp cloth and similar may lead to risk
of injury, ignition or fire.
• If smoke is emitted, switch off or unplug the appliance and
keep the door closed in order to stifle any flames.
• Microwave heating of beverages can result in delayed
eruptive boiling. Care must be taken when handling the
container.
• The contents of feeding bottles and baby food jars shall be
stirred or shaken and the temperature checked before
consumption, in order to avoid burns.
• Eggs in their shell and whole hard-boiled eggs should not
be heated in the appliance since they may explode, even
after microwave heating has ended.
• The appliance should be cleaned regularly and any food
deposits removed.
• Failure to maintain the appliance in a clean condition could
lead to deterioration of the surface that could adversely
affect the life of the appliance and possibly result in a
hazardous situation.
4 Progress
SAFETY INSTRUCTIONS
Installation
WARNING! Only a qualified
person must install this
appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not pull the appliance by the handle.
• Keep the minimum distance from other
appliances and units.
• Install the appliance in a safe and
suitable place that meets installation
requirements.
• The appliance is equipped with an
electric cooling system. It must be
operated with the electric power supply.
• The built-in unit must meet the stability
requirements of DIN 68930.
Cabinet minimum
height (Cabinet un‐
der the worktop mini‐
mum height)
444 (460) mm
Cabinet width 560 mm
Cabinet depth 550 (550) mm
Height of the front of
the appliance
455 mm
Height of the back of
the appliance
440 mm
Width of the front of
the appliance
595 mm
Width of the back of
the appliance
559 mm
Depth of the appli‐
ance
567 mm
Built in depth of the
appliance
546 mm
Depth with open
door
882 mm
Ventilation opening
minimum size. Open‐
ing placed on the
bottom rear side
560x20 mm
Mains supply cable
length. Cable is
placed in the right
corner of the back
side
1500 mm
Mounting screws 3.5x25 mm
Electrical connection
WARNING! Risk of fire and
electric shock.
• All electrical connections should be
made by a qualified electrician.
• The appliance must be earthed.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by
our Authorised Service Centre.
• Do not let mains cables touch or come
near the appliance door or the niche
below the appliance, especially when it
operates or the door is hot.
• The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
Progress 5
• If the mains socket is loose, do not
connect the mains plug.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
• The electrical installation must have an
isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation device
must have a contact opening width of
minimum 3 mm.
• This appliance is supplied with a main
plug and a main cable.
Use
WARNING! Risk of injury,
burns and electric shock or
explosion.
• This appliance is for household use
only.
• Do not change the specification of this
appliance.
• Make sure that the ventilation openings
are not blocked.
• Do not let the appliance stay
unattended during operation.
• Deactivate the appliance after each
use.
• Be careful when you open the
appliance door while the appliance is in
operation. Hot air can release.
• Do not operate the appliance with wet
hands or when it has contact with
water.
• Do not apply pressure on the open
door.
• Do not use the appliance as a work
surface or as a storage surface.
• Open the appliance door carefully. The
use of ingredients with alcohol can
cause a mixture of alcohol and air.
• Do not let sparks or open flames to
come in contact with the appliance
when you open the door.
• Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
• Do not use microwave function to
preheat the oven.
WARNING! Risk of damage to
the appliance.
• To prevent damage or discoloration to
the enamel:
– do not put aluminium foil directly on
the bottom of cavity of the
appliance.
– do not put water directly into the hot
appliance.
– do not keep moist dishes and food
in the appliance after you finish the
cooking.
– be careful when you remove or
install the accessories.
• Discoloration of the enamel or stainless
steel has no effect on the performance
of the appliance.
• Use a deep pan for moist cakes. Fruit
juices cause stains that can be
permanent.
• This appliance is for cooking purposes
only. It must not be used for other
purposes, for example room heating.
• Always cook with the oven door closed.
• If the appliance is installed behind a
furniture panel (e.g. a door) make sure
the door is never closed when the
appliance is in operation. Heat and
moisture can build up behind a closed
furniture panel and cause subsequent
damage to the appliance, the housing
unit or the floor. Do not close the
furniture panel until the appliance has
cooled down completely after use.
Care and cleaning
WARNING! Risk of injury, fire,
or damage to the appliance.
• Before maintenance, deactivate the
appliance and disconnect the mains
plug from the mains socket.
• Make sure the appliance is cold. There
is the risk that the glass panels can
break.
6 Progress
• Replace immediately the door glass
panels when they are damaged.
Contact the Authorised Service Centre.
• Make sure the cavity and the door are
wiped dry after each use. Steam
produced during the operation of the
appliance condensates on cavity walls
and can cause corrosion.
• Clean regularly the appliance to
prevent the deterioration of the surface
material.
• Fat and food remaining in the appliance
can cause fire and electric arcing when
the microwave function operates.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use any abrasive products,
abrasive cleaning pads, solvents or
metal objects.
• If you use an oven spray, follow the
safety instruction on it's packaging.
• Do not clean the catalytic enamel (if
applicable) with any kind of detergent.
Internal lighting
WARNING! Risk of electric
shock.
• The type of light bulb or halogen lamp
used for this appliance is for household
appliances only. Do not use it for house
lighting.
• Before replacing the lamp, disconnect
the appliance from the power supply.
• Only use lamps with the same
specifications.
Service
• To repair the appliance contact the
Authorised Service Centre.
• Use original spare parts only.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the
mains supply.
• Cut off the mains electrical cable close
to the appliance and dispose of it.
• Remove the door catch to prevent
children or pets from becoming trapped
in the appliance.
PRODUCT DESCRIPTION
General overview
1 2
8
4
3
1
2
3
6
4
5
7
1
Control panel
2
Electronic programmer
3
Heating element
4
Microwave generator
5
Lamp
6
Fan
7
Shelf support, removable
8
Shelf positions
Progress 7
Accessories
Wire shelf
For cookware, cake tins, roasts.
Baking tray
For cakes and biscuits.
CONTROL PANEL
Electronic programmer
21 3 4 5 6 7 8 9 10 11
Use the sensor fields to operate the appliance.
Sensor
Field
Function Description
1
- DISPLAY Shows the current settings of the appliance.
2
ON / OFF To activate and deactivate the appliance.
3
OPTIONS To set an oven function or an automatic pro‐
gramme (only when the appliance is activated).
4
MICROWAVE To activate the Microwave function. When the
function is active, press this sensor field to change
the microwave power.
5
TEMPERATURE /
FAST HEAT UP
To set and see the cavity temperature or the core
temperature sensor temperature (if present). If you
press it and hold for three seconds, it turns the
Fast heat up function ON and OFF.
6
DOWN To move down in the menu.
8 Progress
Sensor
Field
Function Description
7
UP To move up in the menu.
8
OK / Microwave
Quick Start
To confirm a selection or setting. To activate the
Microwave function when the appliance is deacti‐
vated. Each press of this sensor field adds 30 sec‐
onds to the duration.
9
OVEN LIGHT To activate or deactivate the oven lamp.
10
CLOCK To set the clock functions.
11
MINUTE MINDER To set the Minute Minder.
Display
A B C
DEFG
A. Oven function symbol
B. Temperature / time of day / microwave power
display
C. Clock / Residual heat display / Minute Minder
D. Residual heat indicator
E. Indicators for the clock functions
F. Heat-up indicator / Fast Heat Up indicator
G. Number of an oven function / programme
Other indicators of the display:
Symbol Name Description
Automatic programme You can choose an automatic programme.
Microwave function The microwave function operates.
/
kg / g An automatic programme with a weight in‐
put operates.
/
h / min A clock function operates.
Watt You can set the power for the microwave
function.
Temperature / Fast heat up The function operates.
Temperature The current temperature is indicated.
Temperature You can change the temperature.
Progress 9
Symbol Name Description
Light You deactivated the light.
Minute minder The minute minder function operates.
Heat up indicator
If you turn on the heating function,
appears. The bars show that the
temperature in the oven increases or
decreases.
When the oven is at the set temperature,
the bars go off the display.
BEFORE FIRST USE
WARNING! Refer to Safety
chapters.
To set the Time of day refer to
"Clock functions" chapter.
Initial Cleaning
Remove all accessories and removable
shelf supports from the oven.
Refer to "Care and cleaning" chapter.
Clean the oven and the accessories
before the first use.
Put the accessories and the removable
shelf supports back to their initial position.
Setting the time
After the first connection to the mains, all
symbols in the display are on for some
seconds. For the subsequent few seconds
the display shows the software version.
After the software version goes off, the
display shows h and 12:00.
1. Touch or to set the hours.
2. Touch .
3. Touch or to set the minutes.
4. Touch or .
The Temperature / Time display shows
the new time.
Changing the time
You can change the time of day only when
the appliance is on.
Touch again and again until flashes
in the display.
To set the new time of day, refer to
"Setting the time".
DAILY USE
WARNING! Refer to Safety
chapters.
10 Progress
Heating Functions
Oven func‐
tion
Application
True Fan
Cooking
To bake on up to two
shelf positions at the
same time and to dry
food.
Set the temperature 20 -
40 °C lower than for Con‐
ventional Cooking.
Pizza Func‐
tion
To bake pizza. To make
intensive browning and a
crispy bottom.
Conventional
Cooking
To bake and roast food
on one shelf position.
Slow Cooking
To prepare tender, suc‐
culent roasts.
Bottom Heat
To bake cakes with
crispy bottom and to pre‐
serve food.
Defrost
To defrost food (vegeta‐
bles and fruit). The de‐
frosting time depends on
the amount and size of
the frozen food.
Keep Warm
To keep food warm.
Grill
To grill flat food and to
toast bread.
Frozen Foods
To make convenience
food (e.g. french fries,
potato wedges or spring
rolls) crispy.
Oven func‐
tion
Application
Turbo Grilling
To roast larger meat
joints or poultry with
bones on one shelf posi‐
tion. To make gratins and
to brown.
The lamp may turn off
automatically at a temperature
below 60 °C during some oven
functions.
Setting the heating function
1. Turn on the oven with .
The display shows the set temperature,
the symbol and the number of the heating
function.
2. Press or to set a heating
function.
3. Press or the oven starts
automatically after 5 seconds.
If you turn on the oven and do not set any
heating function or programme, the oven
turns off automatically after 20 seconds.
Changing the temperature
Press or to change the
temperature in steps: 5 °C.
When the oven is at the set temperature a
signal sounds and the Heat up indicator
disappears.
Checking the temperature
You can check the current temperature in
the oven when the function or programme
works.
1. Press .
The display shows the temperature in the
oven.
Press again to change the set
temperature.
2. Press or the display shows again
the set temperature automatically after
5 seconds.
Progress 11
Fast Heat Up
Do not put food in the oven when the Fast
heat up works.
The Fast Heat Up is available only for
some heating functions. If Faulty Tone is
turned on in the settings menu, the signal
sounds if the Fast Heat Up is not available
for the set function. Refer to "Additional
functions" chapter, Using the settings
menu.
The Fast Heat Up decreases the heat up
time.
To turn on the Fast Heat Up press and
hold for more than 3 seconds.
If the Fast Heat Up is turned on the
display shows flashing bars.
MICROWAVE MODE
WARNING! Refer to Safety
chapters.
Microwave functions
Functions Description
Microwave Creates the heat directly in the food. Use it to heat pre-prepared meals
and drinks, to defrost meat or fruit, and to cook vegetables and fish.
Combi Use it to operate the oven function and the microwave mode together.
Use it to cook food in a shorter time and brown it at the same time.
Quick Start Use it to activate the Microwave function with one touch of the sensor
field with the maximum microwave power. Operating time: 30 sec‐
onds.
Setting the Microwave function
Deactivate the appliance to use the
normal Microwave function.
1. Touch to activate the Microwave
function.
The display shows the symbol and the
default microwave power.
2. Touch or to change the
microwave power. The power setting
changes in 100 Watt steps.
3. Touch to set the DURATION. Refer
to "Setting the DURATION". Confirm
with to start the Microwave
function.
If you do not set the
DURATION and start the
Microwave function with
directly, the duration is 30
seconds. Each press of this
sensor field adds 30
seconds to the duration.
If you do not touch , the
appliance deactivates after 20
seconds.
The maximum setting of the
time for the DURATION is 90
minutes.
You can change the microwave
power (touch and then
or ) and the DURATION
(touch ) any time when the
Microwave function operates.
12 Progress
4. When the set time ends, an acoustic
signal sounds for 2 minutes. The
Microwave function deactivates
automatically. Touch a sensor field to
stop the acoustic signal.
To deactivate the appliance, touch .
If you touch or open the
door, the function stops. To
start it again, touch .
The maximum time of microwave
functions depends on microwave power
you set:
MICROWAVE
POWER
MAXIMUM TIME
100 - 600 W -
More than 600 W 7 minutes
Setting the Combi function
1. Activate an oven function. Refer to
"Setting the oven function".
2. Touch and do the same steps as
when you set the Microwave function.
The Combi function is not available with
the function END, SET + GO.
If you set the END function
for the normal oven function, it
changes to the DURATION
in the Combi function.
If you set the DURATION
function for the normal oven
function, it stays active for the
Combi function. If the set
DURATION is longer than 90
minutes, it is not possible to
activate the Combi function.
When you use the Microwave function in
Combi mode the Microwave power cannot
be more than 600 W.
Setting the Quick Start function
1. Touch to deactivate the appliance.
2. Touch to activate the Quick Start
function.
Each touch of adds 30 seconds to the
duration time.
You can change the microwave
power (refer to "Setting the
Microwave function").
3. Touch to set the time for the
DURATION function. Refer to "Setting
the DURATION".
Progress 13
CLOCK FUNCTIONS
Clock functions table
Clock function Application
COUNT UP TIMER To set the count up, which shows how long the appliance
operates. This function has no effect on the operation of
the appliance.
TIME OF DAY To show the time of day. To change the time of day, refer
to "Setting the time".
DURATION To set how long the appliance operates.
END To set when the appliance deactivates. You can use Dura‐
tion and End at the same time (Time delay) if you want the
appliance to activate and deactivate automatically later.
SET+GO To start the appliance with necessary settings with only
one touch of the sensor field any time later.
Count Up Timer
The Count Up Timer is not
activated if Duration and End
are set.
The Count Up Timer starts to count when
the appliance starts to heat.
1. To reset the Count Up Timer, touch
.
2. Touch until the display shows
"00:00" and the Count Up Timer starts
to count up again.
Setting the DURATION
1. Activate the appliance and set an oven
function and temperature.
2. Touch again and again until the
display shows .
flashes in the display.
3. Use
or to set the minutes for
DURATION.
4. Touch
to confirm.
5. Use
or to set the hours for
DURATION.
If you touch
or while
you set the DURATION, the
appliance switches to the
setting of the END function.
6. When the set time ends, an acoustic
signal sounds for two minutes.
and time setting flash in the display.
The appliance deactivates.
7. Touch a sensor field or open the oven
door to stop the acoustic signal.
8. Deactivate the appliance.
Setting the END
1. Activate the appliance and set an oven
function and temperature.
2. Touch again and again until the
display shows .
flashes in the display.
3. Use or to set the END and
or to confirm. First you set the
minutes and then the hours.
When the set time ends, an acoustic
signal sounds for two minutes.
symbol
and the time setting flash in the display.
The appliance deactivates.
4. Touch a sensor field or open the oven
door to stop the acoustic signal.
14 Progress
5. Deactivate the appliance.
Setting: Set + Go
You can use the Set + Go function only
when the Duration is set.
1. Set a heating function and
temperature.
2. Set the Duration.
3. Press again and again until the
display shows flashing .
4. Press to set the Set + Go function.
The display shows and with an
indicator. This indicator shows which clock
function is activated.
5. Press a sensor field (apart from ON /
OFF) to start the Set + Go function.
Setting the MINUTE MINDER
Use the MINUTE MINDER to set a
countdown. This function has no effect on
the operation of the oven. You can set the
MINUTE MINDER at any time and also
when the appliance is off.
1. Touch .
and "00" flash in the display.
2. Use or to set the MINUTE
MINDER. First you set the seconds,
then the minutes and the hours.
3. Touch
or the MINUTE MINDER
starts automatically after five seconds.
When the set time ends, an acoustic
signal sounds for two minutes and 00:00
and flash in the display.
4. Touch a sensor field or open the oven
door to stop the acoustic signal.
Setting the Time delay function
The DURATION and END can be
used at the same time, if the appliance is
to be switched on and off automatically
later. In this case, first set the DURATION
and then the END function (refer to
"Setting the DURATION" and "Setting the
END" ).
When the Time delay function
is activated, the display shows
a static symbol of the oven
function, with a dot and .
The dot shows which clock
function is on in the Clock /
residual heat display.
AUTOMATIC PROGRAMMES
WARNING! Refer to Safety
chapters.
There are 9 automatic programmes. Use
an automatic programme or recipe when
you do not have the knowledge or
experience on how to prepare a dish. The
display shows the shelf position and the
default cooking times for all automatic
programmes.
Automatic programmes
Programme number Programme name
1 MEAT
2 FROZEN VEGETABLES
3 CHICKEN, WHOLE
Progress 15
Programme number Programme name
4 MUFFINS
5 PIZZA
6 POTATO GRATIN
7 SWEET TART
8 WHITE BREAD
9 BRAISED MEAT
Automatic programmes
1. Activate the appliance.
2. Touch .
The display shows and the number of
the automatic programme.
3. Touch or to choose the
automatic programme.
4. Touch or wait five seconds until
the appliance automatically starts to
work.
When you choose an
automatic programme with
microwave mode, the
appliance will not start
automatically if you do not
close the door. After you
close the door, confirm the
selection with .
5. When the set time ends, an acoustic
signal sounds for two minutes. The
symbol flashes.
The appliance deactivates.
6. Touch a sensor field or open the door
to stop the acoustic signal.
Automatic programmes with
weight input
If you set the weight of the meat, the
appliance calculates the roasting time.
1. Activate the appliance.
2. Touch .
3. Touch or to set the weight
programme.
The display shows: the cooking time, the
duration symbol , a default weight, a
unit of measurement (kg, g).
4. Touch or the settings save
automatically after five seconds.
The appliance activates.
5. You can change the default weight
value with or . Touch .
6. When the set time ends, an acoustic
signal sounds for two minutes.
flashes.
The appliance deactivates.
7. Touch a sensor field or open the door
to stop the acoustic signal.
USING THE ACCESSORIES
WARNING! Refer to Safety
chapters.
Inserting the accessories
Use only suitable cookware and material.
WARNING! Refer to "Hints and
tips" chapter, Microwave
suitable cookware and
materials.
Wire shelf:
16 Progress
Push the shelf between the guide bars of
the shelf support and make sure that the
feet point down.
Baking tray:
Push the baking tray between the guide
bars of the shelf support.
Wire shelf and baking tray together:
Push the baking tray between the guide
bars of the shelf support and the wire shelf
on the guide bars above.
Small indentation at the top
increase safety. The
indentations are also anti-tip
devices. The high rim around
the shelf prevents cookware
from slipping of the shelf.
ADDITIONAL FUNCTIONS
Using Child Lock
The Child Lock prevents an accidental
operation of the oven.
You can turn on this function when the
oven is off. Do not set a heating function.
Press and hold and at the same
time for 2 seconds. The signal sounds.
The display shows SAFE.
Repeat the action to turn off the Child
Lock.
Using the Function Lock
You can turn on the function only when
the oven works.
The Function Lock prevents an accidental
change of the oven function.
1. To turn on the function turn on the
oven.
2. Turn on an oven function or setting.
3. Touch and hold and at the
same time for 2 seconds.
A signal sounds.
Lock comes on in the display.
To turn off the Function Lock repeat step
3.
You can turn off the oven when
the Function Lock is on. When
you turn off the oven, the
Function Lock turns off.
Using the settings menu
The settings menu lets you turn on or turn
off functions in the main menu. The
display shows SET and the number of the
setting.
Progress 17
Description Value to set
1 SET+GO ON / OFF
2 RESIDUAL HEAT INDICATOR ON / OFF
3
KEY TONE
1)
CLICK / BEEP / OFF
4 FAULTY TONE ON / OFF
5 BRIGHTNESS LOW / MEDIUM / HIGH
6 SERVICE MENU -
7 RESTORE SETTINGS YES / NO
1)
It is not possible to deactivate the tone of the ON / OFF sensor field.
1. Press and hold for 3 seconds.
The display shows SET1 and "1" flashes.
2. Press or to set the setting.
3. Press .
4. Press or to change the value of
the setting.
5. Press .
To exit the Settings menu, press or
press and hold .
Automatic Switch-Off
For safety reasons the oven turns off
automatically after some time, if a heating
function works and you do not change any
settings.
(°C) (h)
30 - 115 12.5
120 - 195 8.5
200 - 230 5.5
The Automatic Switch-off does not work
with the functions: Light, Duration, End
Time.
Brightness of the display
There are two modes of display
brightness:
• Night brightness - when the appliance
is deactivated, the brightness of the
display is lower between 10 PM and 6
AM.
• Day brightness:
– when the appliance is activated.
– if you touch a sensor field during
the night brightness (apart from
ON / OFF), the display goes back
to the day brightness mode for the
next 10 seconds.
– if the appliance is deactivated and
you set the Minute Minder. When
the Minute Minder function ends,
the display goes back to the night
brightness.
Cooling fan
When the oven operates, the cooling fan
turns on automatically to keep the
surfaces of the oven cool. If you turn off
the oven, the cooling fan can continue to
operate until the oven cools down.
HINTS AND TIPS
WARNING! Refer to Safety
chapters.
18 Progress
The temperature and baking
times in the tables are
guidelines only. They depend
on the recipes and the quality
and quantity of the ingredients
used.
Cooking recommendations
Your oven may bake or roast differently to
the oven you had before. The tables
below show recommended settings for
temperature, cooking time and shelf
position for specific types of the food.
If you cannot find the settings for a special
recipe, look for the similar one.
Microwave recommendations
Let's cook!
Place the food on a plate on the bottom of the cavity.
Turn or stir the food halfway through the defrosting and cooking time.
Stir liquid dishes from time to time.
Stir the food before serving.
Cover the food for cooking and reheating.
Put the spoon to the bottle or glass when heating drinks to ensure better heat distribution.
Put the food into the oven without packaging. The packaged ready meals can be put into the
oven only when the packaging is microwave safe (check information on the packaging).
Microwave cooking
Microwave defrosting
Cook food covered. If you want to keep a
crust cook food without a cover.
Do not overcook the dishes by setting the
power and time too high. The food can dry
out, burn or cause fire.
Do not use the oven to cook eggs or snails in
their shells, because they can burst. Pierce
the yolk of fried egg before reheating it.
Pierce food with skin or peel several times
before cooking.
Cut vegetables into similar-sized pieces.
After you turn off the oven, take the food out
and let it stand for a few minutes.
Put the frozen, unwrapped food on a small
upturned plate with a container below it, or
on a defrosting rack or plastic sieve so that
the defrosting liquid can leak out.
Remove defrosted pieces subsequently.
To cook fruit and vegetables without defrost‐
ing them first, you can use a higher micro‐
wave power.
Progress 19
Microwave suitable cookware and materials
For the microwave use only suitable cookware and materials. Use below table as a
reference.
Cookware / Material Microwave function Microwave Combi
function
De‐
frosting
Heating,
Cooking
Ovenproof glass and porcelain with no
metal components, e.g. heat-proof
glass
Non-ovenproof glass and porcelain
without any silver, gold, platinum or
other metal decorations
X X
Glass and glass ceramic made of
ovenproof / frost-proof material
Ceramic and earthenware without any
quartz or metal components and gla‐
zes which contain metal
X
Ceramic, porcelain and earthenware
with unglazed bottom or with small
holes, e.g. on handles
X X X
Heat-resistant plastic up to 200 °C
(please always check the plastic con‐
tainer specification before use)
X
Cardboard, paper X X
Clingfilm X X
Roasting film with microwave safe clo‐
sure (please always check the film
specification before use)
X
Roasting dishes made of metal, e.g.
enamel, cast iron
X X
Baking tins, black lacquer or silicon-
coated (please always check the bak‐
ing tins specification before use)
X X
Baking tray X X X
Wire shelf X X
Cookware for microwave use, e.g.
crisp pan
X X
Baking
Use the lower temperature the first time.
20 Progress
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
