1
ENGLISH
Contents
Safety Instructions .............................................................................................................................. 2
Resource Recycle Information........................................................................................................... 3
System Components and Accessories ............................................................................................. 4
Installation Instructions...................................................................................................................... 5
Installing the Display....................................................................................................................... 5
Packaging Procedures.................................................................................................................... 5
Adjusting the Viewing Angle........................................................................................................... 5
Connection Instructions.................................................................................................................. 6
Using the Display ............................................................................................................................... 7
Turning On the Display................................................................................................................... 7
Function Controls............................................................................................................................ 7
OSD Selection...................................................................................................................................... 8
OSD Menu...................................................................................................................................... 8
Troubleshooting .................................................................................................................................. 9
Product Specifications...................................................................................................................... 10
Appendix ............................................................................................................................................ 11
2
Safety Instructions
• Do not place the LCD display near any heat sources such as electric radiators or
direct sunlight. Place the display in a stable and well-ventilated place.
• The holes or openings on the display are for ventilation. Do not cover or block the
ventilation holes with any objects.
• As the LCD display surface is easy to be scratched, avoid touching the surface with
nail or pen point.
• Make sure to unplug the product from the power outlet before cleaning. Use a soft
lint-free cloth instead of a tissue to wipe the screen.
You may use a glass cleaner to clean the product if required. However, never spray
the cleaner directly onto the display surface.
• Do not attempt to service this product yourself! Improper disassembly of the product
may expose you to danger! If your problem cannot be solved according to the
“Troubleshooting” guides, please contact qualified service personnel.
3
ENGLISH
Recycling information
We, Gigabyte Technology, care very much about our environment protection strategy and firmly
believe that it helps us have healthier earth via appropriate treatment and recycling of industrial
technology devices at the end-of-life.
These devices contain recyclable materials, which can be re-decomposed and re-integrated into
brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned
substances. We strongly encourage you to contact the provided information to recycle this product.
United State : http://newyork.earth911.org/
Asia : http://recycle.epa.gov.tw/public/public4_2.htm
Europe :
Ireland
Company : McGrath Environmental Consultants Ltd.
Contact Person : Ms. McGrath Clodagh
Add ress: 20 Lower John Street, Cork, Ireland.
Tel : 021 4554833 Fax : 021 4505805
Norway :
Company : Bergfald & Co as Contact Person : Mr. Solevåg Øystein
Address : Solavågsvegen 90, EIDSNES, NORWAY ,Post Code : N-6037
Tel : +47 40 23 47 05 Fax : +47 70 19 40 17
Web site : http://www.bergfald.no/english.html
United Kingdom :
Company : ARENA Network Contact Person : Dr. Tillotson Allen
Add : Bank Buildings Treforest Estate, Pontypridd, Rhondda Cynon Taff, Kindom Post Code :
CF37 5UR
Tel : 01443 844001 Fax : 01443 844002
Web site : http://www.arenanetwork.org
4
System Components and Accessories
If any component is missing, please contact your local dealer for technical support or customer service.
Remark: Please keep the original box and packing materials for future transportation or
shipment of the display.
LCD Display
Power Cord
Audio Cable
Signal Cable (VGA)
User Manual
5
ENGLISH
Installation Instructions
Installing the Display
1. Place the display onto the base.
Packaging Procedures
If you need to package the display, please unplug the display panel from the base before placing
them into a box. The procedures are as follows:
1. Unplug the power cord from the display (make sure all attached peripherals are already turned
off).
2. Push forward the four latches inside the base and hold the latches.
3. Unplug the display panel from the base and then put them into an outer box.
Important
Before you start, place a clean tower or cloth on a flat surface so that you can lay the display panel
on a clean flat place without being damaged. Slightly lift the display when unplugging it from the
base.
Adjusting the Viewing Angle
You may adjust the display’s viewing angle from –5° to 20°.
2. Align the display with the swivel on the
base and plug the display into the base.
6
Connection Instructions
Note: Before installation, please make sure to power off the display and the computer.
○
1
Power Cord Plug the female end of the power cord to the power socket on the rear of
the display. Then plug the male end to the AC power outlet.
○
2
Signal Cable
(VGA)
As one end of the signal cable is already attached to the display, just
connect the other end to the output jack on your PC’s video card and
then fasten the screws.
○
3
Audio Cable Connect one end of the audio cable to the audio in socket on the display
and the other end to the audio out jack on your PC.
! Warning:
1. Please verify the video card you are using and use appropriate signal cable.
2. Pay attention to the PIN assignments and connection directions. Do not force to bend the pins.
7
ENGLISH
Using the Display
Turning On the Display
Turn on the display before turning on the computer. When the power is on, the LED on the power
button lights green and the screen image will appear after about 10 seconds. If the LED doesn’t light
green or no image appears, please verify if the display is properly connected.
Function Controls
1
POWER
Power Switch
Power On/Off
Green-Operation mode / Orange-Power saving mode
2
SELECT/AUTO
Auto Adjustment
Button
OSD Off: Executes auto adjustment function.
OSD On: Confirms an OSD selection.
3 and
Left / Right Button
Decrease / Increase
Button
OSD Off: Press or can directly adjust the “volume”.
OSD On: Use these buttons to adjust the values of a
selected function.
4 and
Left / Right Button
Decrease / Increase
Button
OSD On: Use these buttons to scroll through the items in
OSD menu.
OSD Off: Use these buttons to adjust the brightness and
contrast.
5
MENU
OSD
Function
Enters / Exits OSD
8
OSD Selection
After you press the MENU button to enter the OSD menu, use ,,, to select the items you want
to adjust. Then press the SET AUTO button. After the screen fonts turn from black to blue you may
start to make the adjustments. Just use ,,, to adjust the screen parameters as required. If no
action is taken for 45 seconds after the setting, the system will automatically save your settings and exit
the OSD.
OSD Menu
Brightness/Contrast
Brightness: Press or (○
6
and○
5
in figure 4) to adjust the brightness
of the screen.
Contrast: Pressor (○
4
and○
3
in figure 4) to adjust the contrast of the
screen.
Image Control:
Auto Adjustment: Use the MENU button (X in figure 4) to automatically
optimize the image parameters (such as image position and phase).
Horizontal Position Adjustment: Adjust horizontal position of the image.
Vertical Position Adjustment: Adjust vertical position of the image.
Clock: Set up the internal clock. Increase or decrease the value allows
adjusting the image width.
Phase: Adjust the time offset of the internal clock. It is used to optimize
the screen image.
Color Temperature:
In the OSD, pressor (○
4
and○
3
in figure 4). This option allows you to
select a default color temperature (9300K or 6500K). Color temperature
changes will take effect immediately on the display. To adjust a color
independently, select the “User Adjustment” item and then press MENU
(X in figure 4) to select red, green or blue. In the OSD, press or (○
6
and○
5
in figure 4) to select the required values. When you return to the
menu of previous level or exit the OSD menu, current settings will be
saved automatically.
OSD Control:
OSD horizontal position adjustment: Adjust the horizontal position of the
OSD menu.
OSD vertical position adjustment: Adjust the vertical position of the OSD
menu.
OSD timeout: Set the time duration (in seconds) when the OSD menu
disappears from the screen if no action is taken.
Other
Language: English, Simplified Chinese, Traditional Chinese
Input Signal: Control the selection of input signals. The display allows
you to connect to an analog video card via 15-pin mini D-Sub interface.
Volume: Adjust the output volume of the display speaker.
Information: This OSD screen is optional (On/Off). It displays the latest
screen resolution settings.
Note: Do not adjust the screen settings when animation is displayed and make sure to adjust the
settings in full screen mode.
9
ENGLISH
Troubleshooting
Problems Possible Solutions
Power LED doesn’t light on.
• Check if the power switch is in the ON position.
• Make sure the power cord is properly
connected.
No screen image.
• Check if the power switch is in the ON position.
• Make sure the power cord is properly
connected.
• Make sure the signal cable is securely
connected.
• When the display is in use, it will automatically
turn off to enter the power saving mode. Please
press any key to see if the image resumes.
Abnormal colors are present.
• Please refer to the “Color Temperature” section
to adjust the RGB color or select a color
temperature.
The image bounces or a wave pattern is
present.
• Remove any electrical device that may be
causing electrical interference.
• Check the signal cable and make sure the pins
are not bent.
The screen image is not centered or the size is
incorrect.
• Press the Auto button to automatically optimize
the display status.
• Refer to the “Image Control” section.
Note: Never disassemble or repair the product yourself. If your problem cannot be solved
according to the troubleshooting guides, please contact your local dealer.
10
Product Specifications
LCD Panel Size 20.1” inch
Contrast 600:1 (typical)
Viewing Angel Horizontal: 150°, Vertical: 130° (typical)
Response Time 8 ms (typical)
Brightness
300 cd/㎡(typical)
Input Signal Analog video (15-pin connector)
Display Colors 16 M Color
Frequency Horizontal: 31~ 83 kHz, Vertical: 56 ~ 75 Hz
Max. Resolution 1400 x 1050
Volume Output Output power per channel: 1W, 8 ohm
Power Supply AC: 100–240V, 50–60 Hz;
Power Consumption Display Mode: Max 50 W; LED Color: Green
Sleeping Mode: Less than 4 W; LED Color: Orange
Size Width: 475.9 mm, Height: 451.5 mm, Depth: 64.9 mm
Weight 8.2 Kg (net)
Environment Conditions Operating Temperature/Humidity:
0 ~ 40 ℃, Relative Humidity: 20 - 80%
Storage Temperature/Humidity:
-20 ~60 ℃, Relative Humidity: 8 – 95%
11
ENGLISH
Appendix
CONNECTOR PIN ASSIGNMENT
15 - Pin Color Display Signal Cable:
15
6
10
11 15
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1. Red 9. +5V
2. Green 10. Ground
3. Blue 11. Ground
4. Ground 12. DDC-Serial Data
5. Ground 13. H-Sync
6. R-Ground 14. V-Sync
7. G-Ground 15. DDC-Serial Clock
8. B-Ground
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
