Best WPD38I36SB Installation guide

Brand: Best

Model: WPD38I36SB

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

WPD38I60SB

SV20569 rev. 02

WPD38I SERIES

INTENDED FOR DOMESTIC COOKING ONLY

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 9

AND 10.

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

SUITABLE FOR USE IN DAMP LOCATIONS WHEN INSTALLED IN A

GFCI PROTECTED BRANCH-CIRCUIT.

NTENDED FOR OUTDOOR COVERED PATIO OR LANAI AREA.

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711

BEST; Drummondville, QC, Canada www.BestRangeHoods.com 866-737-7770

For additional information - visit www.BestRangeHoods.com

HB0113

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address or telephone number

listed in the warranty.

2. Before servicing or cleaning unit, switch power off

at service panel and lock service disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done

by qualified personnel in accordance with all

applicable codes and standards, including

fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent backdrafting.

Follow the heating equipment manufacturer’s

guidelines and safety standards such as those

published by the National Fire Protection

Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any additional solid-state

speed control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded and protected by a

GFCI.

10.

Suitable for use in damp locations only when installed

in a GFCI PROTECTED branch-circuit.

11.

This unit is not designed to be used with a charcoal

grill.

12. When applicable local regulations comprise more

restrictive installation and/or certification

requirements, the aforementioned requirements

prevail on those of this document and the installer

agrees to conform to these at his own expenses.

TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

a) Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or

medium settings.

b) Always turn hood ON when cooking at high heat or

when flambeing food (i.e.: Crêpes Suzette,

Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should

not be allowed to accumulate on fans, filters or

exhaust ducts.

d) Use proper pan size. Always use cookware

appropriate for the size of the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS

IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid,

cookie sheet or metal tray, then turn off the burner.

BE CAREFUL TO PREVENT BURNS. IF THE

FLAMES DO NOT GO OUT IMMEDIATELY,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN – You may be

burned.

3. DO NOT USE WATER, including wet dishcloths

or towels – This could cause a violent steam

explosion.

4. Use an extinguisher ONLY if:

A. You own a Class ABC extinguisher and you

know how to operate it.

B. The fire is small and contained in the area

where it started.

C. The fire department has been called.

D. You can fight the fire with your back to an exit.

*Based on “Kitchen Fire Safety Tips” published by NFPA.

- 2 -

CAUTION

1. For general ventilating use only. Do not use to

exhaust hazardous or explosive materials and

vapors.

2. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

3. Your hood motor has a thermal overload which will

automatically shut off the motor if it becomes

overheated. The motor will restart when it will be

cooled down. If the motor continues to shut off and

restart, have the hood serviced.

4. For best capture of cooking impurities, the bottom

of the hood must be located at a minimum distance

of 36" above cooking surface.

5. Two installers are recommended because of the

large size and weight of this hood.

6. To reduce the risk of fire and to properly exhaust

air, be sure to duct air outside—Do not exhaust air

into spaces within walls or ceiling or into attics,

crawl space or garage.

7. This product is equipped with a thermostat which

may start blower automatically. To reduce the risk

of injury and to prevent power from being switched

on accidentally, switch power off at service panel

and lock or tag service panel.

8. Please read specification label on product for

further information and requirements.

- WPD38I SERIES RANGE HOOD SYSTEM -

- 3 -

HL0184

MODEL 437

IGH CAPACITY ROOF CAP)

ODEL 441

(10’’ R

OUND WALL CAP)

ODEL 410

(10” ROUND DUCT

— 2 FT. SECTIONS)

ODEL 418

(10” ROUND

ADJUSTABLE ELBOW)

UAL BLOWER

(INCLUDED)

10” R

OUND ADAPTER

(INCLUDED)

OPTIONAL

DECORATIVE FLUE

AEWPD SERIES

WPD38I SERIES

RANGE HOOD

OPTIONAL BACKSPLASH

ABWPD SERIES

36"

OR 48" WIDTH

(STAINLESS STEEL WALL COVERING

WITH WARMING SHELVES)

OPTIONAL

WALL EXTENSION

AWWPD SERIES

- 4 -

1. INSTALL DUCTWORK AND ELECTRICAL WIRING

Plan where and how the ductwork will be installed.

A straight, short duct run will allow the hood to

perform most efficiently.

Install proper-sized ductwork, elbows and roof or wall

cap. Connect metal ductwork to cap and work back

towards the hood location. Use 2” metal foil duct tape

to seal the joints.

Run 3-wire power supply cable to installation location.

For best capture of cooking impurities, the bottom

of the hood must be located at a minimum

distance of 36" above cooking surface.

18"

WALL CAP

36" MINIMUM ABOVE

COOKING

SURFACE

16" TO

TOP

OF WOOD

MOUNTING

STRIP

OPTIONAL DECORATIVE

FLUE

OR SOFFIT

HH0181A

ROOF CAP

10" ROUND DUCT

10" ROUND ELBOW

10" ROUND

ADAPTER

The power cable must be a GFCI protected

branch circuit.

WARNING

Make sure that the following items are included:

- Range hood

- Wood strip (attached to back of hood)

- Installation manual

- Accessories including:

• Baffle filters with handles: 3 for 36” width model, 4 for 48” width model and 5 for 60” width model

• Shielded halogen bulbs (120 V, 50 W max., MR16 with GU10 base) (2 for 36” width hood, 3 for

48” and 60” width hoods)

• 10” round adapter (taped inside the hood)

• Bag of parts: 3 waterproof wire connectors, 2 no. 8 x 5/8’’ screws, 6 no. 10 x 2’’ hex head screws,

4 no. 10 x 2” flat head screws, 2 wall anchors, 2 washers 3/16’’ ID x 3/4’’ OD

Included in parts bag, but not to be used (please discard): 2 wire clamps LP16-AP,

2 no. 8 x 3/8’’ zinc-plated screws, 8 no. 8 x 3/8’’ stainless steel screws,

4 stainless steel 10-32 locknuts, 4 washers 3/16’’ ID x 3/4’’ OD

2. PREPARE INSTALLATION

NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or

damaged, contact the manufacturer.

When performing installation, servicing or cleaning the unit, it is recommended

to wear safety glasses and gloves.

WARNING

This range hood is not designed for use with a charcoal grill.

WARNING

This range hood is intended for outdoor covered patio or lanai area. As with all

electric appliances, this unit must be protected from the effects of weather.

CAUTION

4. INSTALL WALL EXTENSION (OPTIONAL)

AWWPD Series

Wall extension must be installed before the hood (see instructions packed with wall extension).

- 5 -

3. INSTALL BACKSPLASH (OPTIONAL)

ABWPD Series

(for 36” and 48” widths range hoods only)

Backsplash must be installed before

the hood shell because the hood shell covers the backsplash

top mounting screws (see instructions packed with backsplash).

5. REMOVE KNOCKOUT OPENING

Punch out the electrical knockout hole on the back of

the hood. Install the wire clamp (included in parts

bag).

HR0072

6. REMOVE BAFFLE FILTERS AND GREASE DRIP RAIL

A. Remove tape on filters.

Remove filters from hood and set aside.

NOTE: It is recommended to start with the center one(s).

B. Remove tape on grease drip rail (1).

Lift out grease drip rail and set aside.

HD0462

2. PREPARE INSTALLATION (CONT’D)

Parts sold separately:

- ABWPD Series Backsplash, 36” or 48” width (optional)

- AEWPD Series Decorative flue, to be installed over the hood (optional)

- AWWPD Series Wall extension, 36”, 48” or 60” width (optional)

- Transitions, duct, elbows, dampers, wall and roof caps

Refer to page 3 for a complete list of venting options and model numbers.

NOTE: During installation, protect countertop and/or cooktop.

7. INSTALL ADAPTER

Remove adapter from inside hood.

Using both no. 8 x 3/8” zinc-plated screws from parts

bag, assemble the adapter on the top of the hood.

Seal all joints with metal foil duct tape to eliminate air

leaks.

- 6 -

8. INSTALL WOOD MOUNTING STRIP (IF NOT USING WALL EXTENSION)

Due to the weight of this hood, ensure that the wood strip is attached to all of

the available wall studs and blocking; not into the wall alone.

CAUTION

HJ0069

MOUNTING SCREWS LOCATION

NOTE: If range hood is installed with optional wall extension, refer to the instructions sheet included

with the wall extension for wood mounting strip location.

1. Proper structural support is required to accommodate the weight of the hood. Construct the wall

framing using minimum 2" x 4" lumber.

2. Mark the center location of the hood.

3. Measure and mark a level line on wall above cooktop location for the wood mounting strip (see

illustration on page 4). Install 2" x 4" blockings between wall studs where mounting strip will be

installed. Refer to illustration at right.

4. Remove wood mounting strip from back of hood.

5. Position the wood mounting strip on the wall and secure to the wall studs and blockings using

4 no. 10 x 2’’ flat head screws (included in parts bag).

HD0482A

Existing

Wall Studs

2" x 4"

Blocking

Back of Hood

Wood Mounting

Strip

14¼"

⁄8"

16"

18"

- 7 -

Remove the electrical compartment

cover. Insert the house wiring in the

hood and tighten the wire clamp to

secure the wiring.

9. INSTALL HOOD

HD0464

ELECTRICAL COMPARTMENT COVER

• Although not recommended, if blowers need to be removed, reinstall them

using 10-32 locknuts included in parts bag (maximum torque of 20 lb.).

• Hold the hood until it is completely secured to the wood mounting strip.

CAUTION

Rest the back cavity of the hood on

the wood mounting strip.

Attach 10” round duct to adapter.

Secure the hood to wood mounting

strip using 4 no. 10 x 2’’ hex head

screws (for 36’’ width hood) or 6 screws

(for 48’’ and 60’’ width hoods) at locations

shown at right. Drill two 3/16’’ diameter

holes into the wall for wall anchors

through the existing holes in the lower

back of the hood at locations shown at

right. Then, install both wall anchors

with both no. 8 x 5/8’’ screws and both

washers provided.

HD0463

MOUNTING SCREWS LOCATION

ALL ANCHORS LOCATION

11. CONNECT WIRING

Risk of electric shock. Electrical wiring must be done by qualified personnel in

accordance with all applicable codes and standards. Before connecting wires,

switch power off at service panel and lock service disconnecting means to

prevent power to be switched on accidentally.

WARNING

WATERPROOF WIRE CONNECTORS INSTRUCTIONS:

1. Strip wires 3/8’’.

2. Align frayed strands or conductors.

3. Do not pre-twist. Place stripped wires together with ends even, but lead smaller stranded wires

slightly ahead of larger solid or stranded wire.

4. Twist connector onto wires pushing firmly until hand-tight. DO NOT over torque.

5. When inserting wires into connectors, some sealant may leak out. Wipe off excess sealant in

and around conductors. DO NOT REUSE.

10. INSTALL DECORATIVE FLUE (OPTIONAL)

AEWPD Series

Refer to the instructions included with the optional decorative flue.

- 8 -

Connect cable into electrical compartment

using provided waterproof wire connectors.

Connect BLACK to BLACK, WHITE to WHITE

and GREEN or bare wire under ground screw.

Reinstall electrical compartment cover.

HE0138

Reinstall grease drip rail. The illustration at right

shows how to reinsert the grease drip rail into the

range hood.

12. REINSTALL GREASE DRIP RAIL AND BAFFLE FILTERS

HD0465

Remove protective plastic film covering filters before installing them.

CAUTION

11. CONNECT WIRING (CONT’D)

It is recommended to install side filters first and finish with center one(s).

1. Insert one end of the filter into the upper channel of the hood.

2. Raise the other end toward the inside of hood and insert in the grease drip rail of the hood.

HD0466

- 9 -

1. To remove lamps, gently push upwards and turn

counterclockwise to disengage bulb leads from

their grooves.

NOTE: To ease removal of the bulbs, use a rubber

dishwashing glove or use suction cup tool

available from Best. Contact Best

Technical Support at 1-800-558-1711 to

order suction cup tool, part no. 99526707.

2. Install the new lamps by placing the bulb leads into their grooves in the socket.

3. Gently push upwards and turn clockwise until secure.

13. LIGHT BULBS REPLACEMENT

This hood requires 120 V, 50 W, MR16 with GU10 base, shielded halogen lamps (included). (2 for

36” width hood, 3 for 48” and 60” width hoods.)

Do not touch lamps during or soon after operation. Burns may occur. In order to

prevent the risk of personal injury, only install shielded halogen lamps. Also,

never install a cool beam, a dichroïc lamp, a lamp not suitable for use in

recessed luminaires or identified for use in enclosed fixtures.

WARNING

14. CARE

Baffle Filters

The baffle filters should be cleaned frequently. Use a warm detergent solution. Wash more often

if your cooking style generates greater grease like frying foods or wok cooking.

Remove baffle filters by pushing them towards the front of the hood and rotating filters downward.

Baffle filters are dishwasher safe. Allow filters to dry completely before reinstalling them in the hood.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the

filter may occur if using phosphate detergent or as a result of local water conditions—but this will

not affect filter performance. This discoloration is not covered by the warranty.

12 3

HO0089

Grease Drip Rail

The grease drip rail should be cleaned frequently. Lift it out from the hood and use a warm detergent

solution. As for the baffle filters, wash more often if your cooking style generates greater grease

like frying foods or wok cooking. Allow grease drip rail to dry completely before reinstalling it in the

hood.

Blowers Cleaning

Remove the filters in order to access the blowers. Vacuum blowers to clean. Do not immerse in

water.

Hood Cleaning

Stainless steel:

Do:

• Regularly wash with clean cloth or rag

soaked with warm water and mild soap or

liquid dish detergent.

• Always clean in the direction of original polish

lines.

• Always rinse well with clear water (2 or 3

times) after cleaning. Wipe dry completely.

• You may also use a specialized household

stainless steel cleaner.

Don’t:

• Use any steel or stainless steel wool or any

other scrapers to remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction

residues reach the hood. During construction/

renovation, cover the hood to make sure no

dust sticks to stainless steel surface.

- 10 -

14. CARE (CONT’D)

Avoid when choosing a detergent:

• Any cleaners that contain bleach will attack stainless steel.

• Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

• Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are

highly explosive and should never be used close to a range.

BLOWER

The blower is operated using two controls.

Use the on/off rocker switch (2) to start and stop

the blower. When turned ON, the switch turns red

and the blower operates at the speed set by the

speed control knob (1).

Turn the speed control knob clockwise to increase

blower speed – counterclockwise to decrease

speed.

COOKTOP LIGHTING (HALOGEN)

Use the on/off rocker switch (3) to turn the halogen

lights ON or OFF.

15. OPERATION

1) B

LOWER SPEED CONTROL KNOB

2) ON/OFF

BLOWER SWITCH

3) H

ALOGEN LIGHT SWITCH

HEAT SENTRY™

This hood is equipped with a Heat Sentry™ thermostat. This thermostat is a device that will turn

on the blower if it senses excessive heat above the cooking surface.

1) If blower is OFF - it turns blower ON to the last selected speed.

2) If blower is already ON speed will remain the same.

When the temperature level drops to normal, the blower will return to its original setting.

The HEAT SENTRY can start the blower during a range top fire or other excessive

heat situations even if the hood is turned off. In this case, it is impossible to turn

the blower OFF using control panel switch. To stop the blower, set the main

power switch located behind the baffle filters in OFF position, if it is possible to

do safely.

WARNING

HD0467

MAIN POWER

SWITCH

HC0058

- 11 -

LINE

NEUTRAL

GROUND

120 VAC

LAMP

SWITCH

LAMP

COLOR CODE

HE0136A

BLK BLACK

BLU BLUE

BRN BROWN

GRY GREY

ORA ORANGE

RED RED

WHT WHITE

YEL YELLOW

WHT

YEL

BLK

BLK BLK

MAIN

SWITCH

FAN SWITCH

RED RED

HEAT SENTRY

THERMOSTAT

GRY

BLU

WHT

ORA

BLK

BLU

WHT

ORA

BLK

BLU

WHT

ORA

BLK

WHT

BLU

WHT

ORA

BLK

RED

GRY

BRN

BLU

WHT

ORA

BLK

BLU

WHT

ORA

BLK

RED

GRY

BRN

YEL

BLK

16. WIRING DIAGRAM

17. WARRANTY

ONE-YEAR LIMITED WARRANTY FOR BEST PRODUCTS

Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of Best products that such

products will be free from defects in materials or workmanship for a period of one year from the date of original

purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED

TO, IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or

part which is found to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND

INCANDESCENT BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES

FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts

which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by

Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty.

Some states or provinces do not allow limitation on how long an implied warranty lasts, so the above limitation

may not apply to you.

BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE

THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE

SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT

OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states or provinces do not

allow the exclusion or limitation of incidental or consequential damages, so the above limitation or

exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state

or province to another. This warranty supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number stated

below, (b) give the model number and part identification and (c) describe the nature of any defect in the product

or part. At the time of requesting warranty service, you must present evidence of the original purchase date.

In USA - Best

;

926 W. State Street, Hartford, WI 53027 (800-558-1711)

In Canada - Best

;

550 Lemire Blvd., Drummondville, QC, Canada, J2C 7W9 (866-737-7770)

www.BestRangeHoods.com

HL0185

- 12 -

18. SERVICE PARTS

*NOT SHOWN.

KEY

PART NO. DESCRIPTION

QTY. (RANGE HOOD WIDTH)

36” 48” 60”

1 SV08541 10” ROUND ADAPTER 1 1 1

2 SV16569 LIGHT SOCKET AND TRIM ASSEMBLY 2 3 3

3 SV05921 SHIELDED HALOGEN BULB (120 V, 50 W, GU10 BASE) 2 3 3

4 SV08582 BLOWER 2 2 2

5 SV08337 FILTER SPRING 3 4 5

6 SV60675 BAFFLE FILTER 11.84” X 15.125” (SPRING & HANDLE INCLUDED) 3 4 5

SV60695

SV60696

SV60697

GREASE RAIL 36”

GREASE RAIL 48”

REASE RAIL 60”

8 SV02563 LIGHT ROCKER SWITCH 1 1 1

9 SV03503 BLOWER ROCKER SWITCH 1 1 1

10 SV08549 FAN KNOB 1 1 1

11 SV03435 HEAT SENTRY™ THERMOSTAT 1 1 1

12 SV08968 SPEED CONTROL 1 1 1

13 SV08548 MAIN POWER SWITCH 1 1 1

* SV05869 BEST LOGO 1 1 1

* SV20569 INSTALLATION GUIDE 1 1 1

* SV04216

PARTS BAG: 3 WATERPROOF WIRE CONNECTORS,

2 NO. 8 X 5/8’’ SCREWS, 6 NO. 10 X 2’’ HEX HEAD SCREWS,

4 NO. 10 X 2” FLAT HEAD SCREWS, 2 WALL ANCHORS,

6 WASHERS 3/16’’ ID X 3/4’’ OD, 4 STAINLESS STEEL 10-32

LOCKNUTS, 2 WIRE CLAMPS LP16-AP, 2 NO. 8 X 3/8’’

ZINC-PLATED SCREWS, 8 NO. 8 X 3/8” STAINLESS STEEL SCREWS

1 1 1

REPLACEMENT PARTS AND REPAIRS

In order to ensure your ventilation unit

remains in good working condition, you

must use Broan-NuTone genuine

replacement parts only. Broan-NuTone

genuine replacement parts are specially

designed for each unit and are

manufactured to comply with all the

applicable certification standards and

maintain a high standard of safety. Any

third party replacement part used may

cause serious damage and drastically

reduce the performance level of your

unit, which will result in premature

failing. Broan-NuTone recommends to

contact a certified service depot for all

replacement parts and repairs.

SV20569 rév. 02

SÉRIE WPD38I

CONÇUE POUR UN USAGE DOMESTIQUE SEULEMENT

INSTALLATEUR : LAISSER CE MANUEL AU PROPRIÉTAIRE.

PROPRIÉTAIRE : DIRECTIVES D’UTILISATION ET D’ENTRETIEN

AUX PAGES 21

ET 22.

LIRE ET CONSERVER CES DIRECTIVES

GUIDE D’INSTALLATION

CONVIENT À UNE INSTALLATION DANS DES LIEUX HUMIDES

LORSQU

’ELLE EST RACCORDÉE À UN

DISJONCTEUR DE FUITE À LA TERRE (DDFT).

ONÇUE POUR FONCTIONNER SUR UN PATIO COUVERT OU UNE VÉRANDA.

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800 558-1711

BEST; Drummondville, QC, Canada www.BestRangeHoods.com 866 737-7770

ENREGISTREZ VOTRE PRODUIT EN LIGNE À : www.BestRangeHoods.com/register

Pour obtenir plus d’information, consultez notre site www.BestRangeHoods.com

HB0113

Page is loading ...

- SYSTÈME DE HOTTE DE CUISINIÈRE SÉRIE WPD38I -

HL0184

MODÈLE 437

APUCHON DE TOIT À

HAUT RENDEMENT

)

ODÈLE 441

APUCHON MURAL 10 PO ROND)

ODÈLE 418

(COUDE AJUSTABLE

DE 10 PO ROND)

ENTILATEUR

DOUBLE

(INCLUS)

DAPTATEUR ROND DE 10 PO

(INCLUS)

CHEMINÉE DÉCORATIVE

OPTIONNELLE

SÉRIE AEWPD

HOTTE

SÉRIE WPD38I

- 15 -

DOSSERET OPTIONNEL

SÉRIE ABWPD

LARGEUR DE 36 PO OU 48 PO

(RECOUVREMENT DE MUR EN

ACIER INOXYDABLE AVEC

SUPPORT ASSIETTES)

RALLONGE DE HOTTE

OPTIONNELLE

SÉRIE AWWPD

ODÈLE 410

(CONDUIT 10 PO ROND,

SECTIONS 2 PI)

Page is loading ...

SV20569 rev. 02

SERIE WPD38I

SÓLO PARA COCINA DOMÉSTICA

INSTALADOR: DEJAR ESTE MANUAL AL PROPIETARIO.

PROPIETARIO: INFORMACIÓN SOBRE LIMPIEZA Y

FUNCIONAMIENTO EN LAS PÁGINAS 33

Y 34.

LEA Y CONSERVE ESTAS INSTRUCCIONES

INSTRUCCIONES DE INSTALACIÓN

ADECUADA PARA LUGARES HÚMEDOS CUANDO SE INSTALA EN UN

CIRCUITO DE DERIVACIÓN PROTEGIDO CON UN DISYUNTOR.

REVISTA PARA PATIOS O TERRAZAS CUBIERTAS.

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711

BEST; Drummondville, QC, Canada www.BestRangeHoods.com 866-737-7770

REGISTRE SU PRODUCTO EN LÍNEA EN: www.BestRangeHoods.com/register

Para obtener más información, visitar nuestro sitio www.BestRangeHoods.com

HB0113

Page is loading ...

- CAMPANAS DE COCINA DE LA SERIE WPD38I -

- 27 -

HL0184

MODELO 437

(

CAPUCHÓN DE ALTA

CAPACIDAD PARA TEJADO

)

ODELO 441

(

CAPUCHÓN MURAL REDONDO DE 10")

ODELO 410

(TUBO REDONDO DE 10",

SECCIONES DE 2 PIES)

ODELO 418

(CODO AJUSTABLE

REDONDO

DE 10")

VENTILADOR

DOBLE (VIENE

CON LA CAMPANA)

DAPTADOR REDONDO

DE 10"

(VIENE CON LA CAMPANA)

SERIE AEWPD, CHIMENEA

DECORATIVA OPCIONAL

CAMPANA

DE LA SERIE

WPD38I

SERIE ABWPD, PLACA

POSTERIOR OPCIONAL

36"

O 48" DE ANCHO

(CUBIERTA PARA PARED DE ACERO INOXIDABLE

CON ESTANTES PARA CALENTAMIENTO)

SERIE AWWPD,

EXTENSIÓN MURAL

OPCIONAL

Page is loading ...

HL0185

- 36 -

18. PIEZAS

*NO SE MUESTRA.

SUSTITUCIÓN DE PIEZAS Y REPARACIÓN

Para que la unidad se conserve en buen

estado, debe usar repuestos genuinos

de Broan-NuTone únicamente. Estas

piezas se han diseñado especialmente

para cada unidad y se han fabricado

conforme a las normas de certificación

aplicables y un elevado nivel de seguridad.

El uso de repuestos de otros fabricantes

podría causar daños graves y reducir

radicalmente el desempeño de la

unidad, causando así fallas prematuras.

Broan-NuTone también aconseja ponerse

en contacto con un taller de reparación

homologado por Broan-NuTone para

todos los repuestos y reparaciones.

N.°

N.° DE

PIEZA

DESCRIPCIÓN

CTD (ANCHURA CAMPANA)

36” 48” 60”

1 SV08541 ADAPTADOR REDONDO DE 10” 1 1 1

2 SV16569 CONJUNTO DE LA LÁMPARA 2 3 3

3 SV05921 BOMBILLAS HALÓGENAS (50 W, 120 V, BASE GU-10) 2 3 3

4 SV08582 VENTILADOR 2 2 2

5 SV08337 RESORTE DEL FILTRO 3 4 5

6 SV60675 FILTROS 11.84” X 15.125” (RESORTE INCLUSIVE) 3 4 5

SV60695

SV60696

SV60697

RIEL DE VERTIDO DE LA GRASA, 36”

IEL DE VERTIDO DE LA GRASA, 48”

IEL DE VERTIDO DE LA GRASA, 60”

8 SV02563 INTERRUPTOR OSCILANTE DE LA LUZ 1 1 1

9 SV03503 INTERRUPTOR OSCILANTE DEL VENTILADOR 1 1 1

10 SV08549 BOTÓN DEL VENTILADOR 1 1 1

11 SV03435 TERMOSTATO HEAT SENTRY™ 1 1 1

12 SV08968 CONTROL DE LA VELOCIDAD 1 1 1

13 SV08548 INTERRUPTOR DE ALIMENTACIÓN PRINCIPAL 1 1 1

* SV05869 LOGO DE BEST 1 1 1

* SV20569 GUÍA DE INSTALACIÓN 1 1 1

* SV04216

BOLSA DE PIEZAS: 3 CONECTORES IMPERMEABLES DE HILOS,

2 TORNILLOS N.° 8 X 5/8’’, 6 TORNILLOS DE CABEZA HEXAGONAL

.° 10 X 2’’, 4 TORNILLOS DE CABEZA PLANA N.° 10 X 2”,

2 SUJECIONES MURALES, 6 ARANDELAS 3/16’’ DI X 3/4’’ DE,

4 TUERCAS DE ACERO INOXIDABLE 10-32, 2 ABRAZADERAS DE

HILOS

LP16-AP, 2 TORNILLOS N.° 8 X 3/8’’ REVESTIDOS DE ZINC,

8 TORNILLOS DE ACERO INOXIDABLE N.° 8 X 3/8”

1 1 1

Best WPD38I36SB Installation guide

Brand: Best

Model: WPD38I36SB

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

WPD38I60SB

Download PDF

report

in other languages

français: Best WPD38I36SB Guide d'installation
español: Best WPD38I36SB Guía de instalación

Best WPD38I36SB Installation guide

This manual is also suitable for

Best WPD38I36SB Installation guide

in other languages

Related papers

Other documents