Fulton F2 Installation guide

Type
Installation guide

This manual is also suitable for

F3647 (Rev-B 19169) 05/13
Handle
Bolt
Adjustable
Winch Handle
Lock
Washer
Small Flat
Washer
Large Flat
Washer
Cap
Bolt
Lock Washer
Handle
Installation
Installing Handle Roller Assembly:
Assemble handle assembly as shown and torque locknut to 20-25 ft-lbs., using a 9/16” socket.
Adjustable Handle (6” to 9” and Right or Left Hand Drive):
This handle can be mounted not only in different length configurations, but also in a right or left hand orientation. In order to switch to a right or left hand
drive first remove the bolt and washers from each side of the drive shaft. Push the hex shaft 1/2”-3/4” through to the other side. Do not try to remove the
shaft completely in order to keep the internal gears and bushings inline. Place the handle bolt and washers on the handle side and torque to 22-25 ft-lbs.
Then repeat for the opposite side of the shaft. Do not over torque.
Attaching Winch Strap:
Use strap anchor provided with winch as pictured above. Pass the strap loop under the cross bolt, insert strap anchor in the strap loop, then pull tight.
Always maintain a minimum of three complete wraps of strap on the drum.
Purchaser/owner must ensure that product is
installed according to these instructions.
Purchaser/owner must not alter or modify the
product.
Operator and bystanders should never position any
part of body under or on the path of any portion of
this product or the load being supported, or
moved.
Do not allow children to play on or around this
product or the load being supported, or moved.
Do not use winch to move humans.
Never exceed the maximum rated capacity. Refer
to stamped markings on top of winch to obtain
rated capacity. If uncertain, contact Cequent
Trailer Products at 1-800-632-3290 or
www.cequentgroup.com
▪ Capacity is based on direct line pull on third layer
of the strap on the drum. Capacity is reduced as
strap builds up on the drum.
Never stand along side winch or guide the strap
with your hands.
•Never operate with slippery, wet, or oily hands and
always maintain a firm grip on the winch handle.
▪ Do not attempt to stop a winch by grabbing the
handle while in motion.
Always maintain a minimum of three layers of
strap on the drum.
A loud clicking sound from the ratchet must be
heard when pulling the load. If properly engaged
and loud clicking sound is not heard, do not use
and replace ratchet components immediately.
Never release the crank handle unless the ratchet
plunger is fully engaged and the load is supported.
Winch will not hold the load when load is being
let out.
Winch is designed for manual operation only and
the load rating is based on an intermittent duty
cycle.
Excessive force in turning winch handle may
indicate overload. Fulton brand winches will
require a max of 45 lbs of handle force to pull
rated load.
If you cannot crank the winch with one hand you
are potentially overloading the winch.
Winches are not designed to secure boats to
trailers while towing. Boat tie downs must be
used for this purpose.
Periodically check mounting hardware for proper
torque and tighten if necessary.
▪ Do not use cable or rope.
Always replace bent, broken, or worn parts before
using this product.
On two-speed winches, make sure that the ratchet
plunger is properly engaged and holding the load
before attempting to change gears.
Failure to follow these warnings and instructions may result
in property damage, serious bodily injury, and/or death.
WARNING
The mounting surface must be equal to or greater than the footprint of the winch frame. When attaching the trailer winch, use the three (3) supplied 3/8”
dia. grade-5 carriage bolts/lock nuts and torque to 28-30 ft-lbs. Check final installation and make sure winch is secure to mounting structure.
Installation Instructions
Warning: Failure to follow all installation instructions could result in
winch failure.
Read, understand and follow all of these instructions and warnings (Instructions) before installing and using this product. Install and use this product only
as specified in these instructions. Improper installation or use of this product may result in property damage, serious injury, and/or death. Never allow
installation or use of this product by anyone without providing them with these instructions. You must read, understand and follow all instructions and
warnings for any product(s) to which this product is used in conjunction with or installed. Save these instructions with the product for use as a reference
for any future installation and use of the product.
Read, Understand, Follow and Save These Instr uctions
Strap
Installation
Cross
Bolt
Strap
Loop
Strap
Anchor
Trailer Winch
Handle Roller
Assembly
Winch
Mounting
Maintenance
The F2 winch is designed with precision fit components and corrosion resistant materials to minimize the frequency of maintenance. Occasional cleaning
with mild soap and water along with light oil lubrication of contact points will prolong peak performance and appearance
Limited Lifetime Warranty
Let Line/Load Out:
Before turning the handle, firmly grip the winch handle and disengage
the ratchet plunger or engage it in the reverse direction. You may have
to take in a small amount of strap to allow the ratchet plunger to
unload. With a firm grip on the winch handle, slowly let out strap. If
you must stop before the load is fully out, be sure the ratchet plunger is
engaged in the forward or loading position and gradually release the
winch handle to be sure the ratchet plunger is holding the load.
Take Line/Load In:
Be sure the ratchet plunger is engaged in the forward or loading
position. As you turn the handle, make sure the strap is winding onto
the drum properly. If you must stop before the load is fully in, be sure
the ratchet plunger is engaged and gradually release the winch handle
to be sure the ratchet plunger is holding the load.
Shifting (2-Speed Winches Only):
Make sure the ratchet plunger is properly engaged and holding the load
before attempting to change gears. Firmly grasp the crank arm of the
F2 2-speed winch where it attaches to the input shaft. Push/pull to
shift. In for High-Gear and out for Low-Gear.
Operation
Engaged
Neutral
Engaged
Disengaged
Not holding load!
Neutral
Strap Over Drum Strap Under Drum
Line direction
Grasp handle here
and push/pull to shift
Ratchet
Plunger
HIGH
LOW
Disengaged
Not holding load!
Prior to Use
- Inspect strap and replace if damaged.
- Check mounting hardware for proper tightness and re-torque if necessary.
- Gears, ratchet contact points and shaft bushings must be kept lubricated with a thin oil or grease.
Limited Lifetime Warranty (“Warranty”). Cequent Trailer Products, Inc. (“We” or “Us”) warrants to the original consumer purchaser only (“You”) that the product will
be free from material defects in both material and workmanship, ordinary wear and tear excepted; provided that installation and use of the product is in accordance with
product instructions. There are no other warranties, express or implied, including the warranty of merchantability or fitness for a particular purpose. This warranty is
not transferable.
Limitations on the Warranty. This Warranty does not cover: (a) normal wear and tear; (b) damage through abuse, neglect, misuse, or as a result of any accident or in any
other manner; (c) damage from misapplication, overloading, or improper installation; (d) improper maintenance and repair; and (e) product alteration in any manner by
anyone other than Us, with the sole exception of alterations made pursuant to product instructions and in a workmanlike manner.
Obligations of Purchaser. To make a Warranty claim, contact Us at 47912 Halyard Dr. Suite 100, Plymouth, MI 48170, 1-800-632-3290, identify the product by model
number, and follow the claim instructions that will be provided. Any returned product that is replaced by Us becomes our property. You will be responsible for return
shipping costs. Please retain your purchase receipt to verify date of purchase and that You are the original consumer purchaser. The product and the purchase receipt
must be provided to Us in order to process Your Warranty claim.
Remedy Limits. Repair or replacement is Your sole remedy under this Warranty. We shall not be liable for service or labor charges incurred in removing or replacing a
product or any incidental or consequential damages of any kind.
Assumption of Risk. You acknowledge and agree that any use of the product for any purpose other than the specified use(s) stated in the product instructions is at Your own
risk.
Governing Law. This Warranty gives You specific legal rights, and You also may have other rights which vary from state to state. This Warranty is governed by the laws
of the State of Michigan, without regard to rules pertaining to conflicts of law. The state courts located in Oakland County, Michigan shall have exclusive jurisdiction
for any disputes relating to this Warranty.
How to Order
Use only Cequent Performance Products’ parts or parts of equal quality for repair. Replacement parts are available through Cequent Performance Products
Customer Service Department, 1-800-632-3290. Please specify product model number.
We declare under our sole responsibility that the F2 Trailer Winch is in conformity
with EN-12100-2:2003 Safety Machinery; Machinery Directive 98/37/EC.
Cequent Performance Products, Inc.
47912 Halyard Dr. Suite 100
Plymouth, MI 48170 USA
800/632-3290
www.cequentgroup.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Fulton F2 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI