Bosch SHXM63W55N Installation guide

en Installation Instructions

fr Notice d’installation

es Instrucciones de instalación

Customer Service:

1-800-944-2904

These instuctions are intended

for use by qualified installers only

Page is loading ...

3

Safety Definitions

This indicates that damage to the appliance or property may occur as a

result of non-compliance with this advisory.

NOTICE

This indicates that death or serious injuries may occur as a result

of non-observance of this warning.

WARNING

!

Note: This alerts you to important information and/or tips.

Table of Contents

Safety Instructions ........................................3

Avoiding General Hazards ..................................4

Tools & Materials .........................................5

Enclosure Requirements ...................................8

Electrial Connections .....................................11

Installation of Mounting Brackets ............................16

Positioning the Dishwasher ................................18

Securing the Dishwasher ..................................22

Water Inlet Connection ....................................23

Drain Connection ........................................24

Attaching the Toe Panel ...................................28

Customer Service ........................................31

This indicates that minor or moderate injuries may occur as a

result of non-observance of this warning.

CAUTION

!

4

To avoid possible injury or property damage, OBSERVE ALL WARNINGS

AND CAUTIONS.

These instructions are intended for use by qualified installers only. The

dishwasher must be installed by a qualified service technician or installer.

• In addition to these instructions, the dishwasher shall be installed to

meet all electrical and plumbing codes and ordinances (both national

and local).

Read these installation instructions completely and follow them carefully.

They will save you time and eort and help to ensure safety and optimum

dishwasher performance.

IMPORTANT

• The dishwasher drain hose must be installed with a portion of it at least

33″ (84 cm) o the cabinet floor; otherwise the dishwasher may not

drain properly.

• This dishwasher is intended for indoor residential use only, and should

not be used in commercial food service establishments.

• This dishwasher is designed to be enclosed on the top and both sides

by cabinetry.

• NEW INSTALLATION - If the dishwasher is a new installation, ensure all

connections are properly made before the dishwasher is moved into

place.

• REPLACEMENT - If the dishwasher is replacing another dishwasher,

check the existing dishwasher connections for compatibility with the

new dishwasher, and replace parts as necessary.

• This appliance has been found to be in compliance with CAN/CSA-C22.2

No. 167/UL 749. It is the responsibility of the owner and the installer

to determine if additional requirements and standards apply in specific

installations.

• Not for outdoor use.

Inspect the Dishwasher

After unpacking the dishwasher and prior to installation, thoroughly inspect

the dishwasher for possible freight or cosmetic damage. Report any damage

immediately. Cosmetic defects must be reported within 30 days of installation.

NOTE: Do not discard any bags or items that come with the original package

until after the entire installation has been completed.

Important Safety Instructions:

Please READ and SAVE this information

5

Avoiding General Hazards

To reduce the risk of electric shock, fire, or injury to persons, the installer

must ensure that the dishwasher is completely enclosed at the time of

installation.

Do not use the dishwasher until it is completely installed. When opening the

door on an uninstalled dishwasher, carefully open the door while supporting

the rear of the unit. Failure to follow this warning can cause the dishwasher

to tip over and result in serious injury.

Before installing the supplied counter top mounting brackets, decide which

method will be used to secure the dishwasher into its opening. Once these

mounting brackets are installed on the dishwasher, removing them is dif-

ficult and will damage the mounting brackets and the dishwasher.

In some conditions, hydrogen gas can form in a hot water system that

has not been used for weeks. Hydrogen gas is explosive. Before filling a

dishwasher from a system that has been o for weeks, run the water from

a nearby faucet in a well ventilated area until there is no sound or evidence

of gas.

Removing any cover or pulling the dishwasher from the cabinet can expose

hot water connections, electrical power and sharp edges or points. Handle

with care.

WARNING

6

Elbow connection with 3/4” female hose threads on one end and fits

your water supply line (copper tubing, compression fitting, or braided

hose) on the other.

Electrical Supply Cable - Minimum #14 AWG, 2 conductor, 1 ground,

insulated copper conductors rated 75° C or higher.

Only needed if house electrical line is not adequate.

Hot Water Supply Line - Minimum 3/8″ O.D. copper tubing or metal

braided dishwasher supply line.

Only needed if house water supply line is not sucient.

Shut-o valve and fittings appropriate for hot water supply line

(copper tubing/compression fitting, or braided hose).

UL listed conduit connector or strain relief is required if you attach the

field wiring directly to the terminal block.

Tools and Materials Needed



Wire Cutter

Needle Nose Pliers

Pliers

Wire Stripper

ø1/16 in

(2 mm)

Adjustable Wrench

Tape Measure

Drill

Hole Saw

Flat Screwdriver

Level

Phillips Screwdriver

7

Materials supplied (All Models)

Screw Clamp (for drain hose)

Junction Box

Edge Protector

Mounting Brackets

Mounting Bracket Screws Ø 4x13 mm

Adhesive Backed Cord Clip

D

E

F

B

A

C

8

Materials Supplied

(Model Dependent; your dishwasher is supplied with one of the toe panel

kits shown below)

Slotted Toe Panel

Installation Guide for Fully Integrated Door Panel

Slotted Toe Panel Screws Ø 4x16 mm

Non-Slotted Toe Panel

Non-Slotted Toe Panel Screws - Black or silver

depending on toe panel color

Toe Panel Mounting Brackets (used with non-slotted

toe panel shown above)

G

H

I

J

K

L

Plastic Toe Panel

M

Slotted Toe Panel (used with Plastic Toe Panel

and Ø 4x 16 screws, H, listed above)

9

Enclosure Requirements

Avoid Scalding or Electrical Shock Hazard!

Make sure the water supply and electrical supply are shut o

before installation or service.

Avoid Electrical Shock/Fire Hazard!

Do not allow the electrical and supply lines to touch.

Note: This dishwasher is designed to be enclosed on the top, back and

both sides by standard residential kitchen cabinetry.

• Select a location as close to the sink as possible for easy access to

water supply and drain lines.

• For proper dishwasher operation and appearance, ensure that the

enclosure is square and has the dimensions shown.

• If the dishwasher is to be installed in a corner, ensure that there is

adequate clearance to open the door as shown.

min 34"

(864 mm)

min 24"

(610 mm)

23

5/8

" - 24

1/4

"

(600 - 616 mm)

1











2

WARNING

!

10

• After locating the proper place for your dishwasher, create required

openings in your cabinets in order to allow for water, drain and electrical

lines on the appropriate side.

• The holes should be cut within the 7 x 2.5" area shown.

7"

(177.8 mm)

3

• If the opening is made through wood, sand it smooth.

• If the opening is made through metal, use the provided edge protector

(B) or other approved method to protect wiring from damage.

4

B

11

• Pull the drain hose out of the packaging base as shown.

• Set toe panel aside for later use.

1

2

b

a

5

• Attach elbow joint to dishwasher as shown. Do not overtighten.

Avoid cross-threading! It will cause leaks. After attaching hose, turn on

water and check for leaks.

NOTICE

• Attach hot water line to elbow.

6

12

• Remove the hose clip at the back of the dishwasher as shown. The

hose clip may be used later to hold the drain hose inside your cabinet.

7

Electrical Connection

Avoid Electrical Shock Hazard!

Do not work on an energized circuit. Doing so could result in

serious injury or death. Only qualified electricians should perform

electrical work. Do not attempt any work on the dishwasher

electric supply circuit until you are certain the circuit is de-

energized.

To avoid possible injury or property damage, care should be exer-

cised when the dishwasher is installed or removed to reduce the

likelihood of damage to the power cord.

Avoid Fire Hazard!

Make sure electrical work is properly installed and checked by

qualified electricians.

Make sure there are no loose electrical connections. Make sure

all electrical connections are properly made.

WARNING

!

13

Grounding Instructions

The dishwasher must be properly grounded before operating. This appli-

ance must be connected to a grounded metal permanent wiring system or

an equipment grounding conductor must be run with the circuit conductors

and connected to the equipment grounding terminal or lead on the dish-

washer. Make sure that the dishwasher is connected to a suitable ground

in compliance with all local codes or, in the absence of a local code, with

the NATIONAL ELECTRICAL CODE in the United States or the CANADIAN

ELECTRIC CODE C22.1-latest edition in Canada as well as any provincial/

state or municipal or local codes that apply.

Note: Installations employing a Receptacle - The accessory cord kit, Model

SMZPC002UC, designed for connection to a receptacle is not provided, but

can be ordered through Customer Service by calling 1-800-944-2904. Make

sure the household receptacle meets the electrical supply requirements as

well as national and local codes. If you choose to permanently connect to

hardwiring, follow the next steps.

Dishwasher Electrical Rating

Volts Hertz Amperes Watts

120 60 12 1,440

(max)

Electrical Supply

The customer has the responsibility of ensuring that the dishwasher electri-

cal installation is in compliance with all national and local electrical codes

and ordinances. The dishwasher is designed for an electrical supply of

120V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded

electrical circuit with a fuse or breaker rated for 15 amps. Electrical sup-

ply conductors shall be a minimum #14 AWG copper wire rated at 75°C

(167°F) or higher.

14

• Turn o any electricity to installation area.

• Remove screws and cover from junction box (A) and set aside for later

use.

• Remove outer casing and insulation of the hardwiring/power cord as

shown.









8

Loose and improperly installed electrical connections can

result in overheating!

Carefully review terminal block installation instructions.

WARNING

!

15

A

• Attach an approved strain relief (not provided) to opposite side of

junction box.

• Without adjusting the terminal screws, insert the wires properly in the

terminal. Make sure that the black wire connects with the black (L)

and the white connects with the white (N) and the green or bare cop-

per wire with the green (G or ). (See box b)

• Do NOT insert wire underneath the screw clamp. (see box a)

• Be certain the wire insulation is not trapped in the terminal. 1-2 mm of

wire must be visible (See box b)

• After inserting wire, completely tighten the terminal screws by turning

clockwise. (See box c)

• After tightening the terminal screws, pull on each wire to ensure that

they are secure. Wire should not be loose in the terminal after correct

installation.

• Secure the wire in the junction box with the strain relief.

Note: The arrow (shown in box d above) should align with the power

cord.

a

b

cd

1-2 mm

ADVERTENCIA

WARNING

AVERTISSEMENT

STRICTLY FOLLOW ALL INSTRUCTIONS IN THIS MANUAL.

USE ONLY 14 OR 12 AWG COPPER WIRE WITH A MIN. TEMP. RATING

OF 75°C (167°F).

PLACE ALL WIRING IN THE POWER SUPPLY BOX AND INSTALL COVER.

CONNECTION SCREWS ARE NOT REMOVABLE.

ESTRICTAMENTE SIGA TODAS LAS INSTRUCCIONES DE ESTE MANUAL.

UTILICE SÓLO EL 14 O 12 DE ALAMBRE DE COBRE AWG CON UN GRADO

DE LA TEMPERATURA MÍNIMA DE 75 ° C (167 ° F).

COLOQUE TODOS LOS CABLES EN LA CAJA DE LA FUENTE DE ALIMEN-

TACIÓN Y LA INSTALACIÓN DE LA CUBIERTA. TORNILLOS DE CONEXIÓN

NO SON EXTRAIBLES.

WIRE STRIP GAGE

1/2" (13 mm)

CALIBRE DE POUR DÉNUDER

INDICADOR DE CABLE PELADO

OBSERVER TOUTES LES INSTRUCTIONS DE CE GUIDE.

UTILISER SEULEMENT DU FIL DE CUIVRE 14 OU 12 AWG AVEC UNE

COTE DE TEMPÉRATURE MINIMALE DE 75°C (167°F).

PLACER TOUS LES FILS DANS LA BOÌTE D‘ALIMENTATION ET

REMETTRE LE COUVERCLE.

LES VIS DE CONNEXIONS NE SONT PAS AMOVIBLES.

view with cover installed

arrow

strain relief

black (L)

white (N)

green (G)

9

16

• Check all electrical connections to ensure they are secure and then

reattach the junction box cover.

• Place adhesive backed cord clip (provided in the installation kit)

5 inches from leg adjuster as shown in the figure above and route

power cord through the clip. Note:The length of cord measured

from the plastic back strap to the receptacle should be ≤ 47.25”

(1,200 mm).

• Plug the end of the supply cord into the back of the dishwasher as

shown until it clicks.

CLICK

Adhesive

backed

cord clip

Leg Adjuster

Strap

5"

(127 mm

)

C

l

ip

o

rie

ntation

A

lternate cable routing

11

10

• Mount the dishwasher electrical supply junction box (A) and dedicated

receptacle in an accessible cabinet adjacent to the dishwasher (do not

mount the junction box or receptacle behind the dishwasher).

Note: Screws are not provided for mounting electrical supply junction box.

A

17

Installation of Mounting Brackets

• Top Mount is used for counter tops made of wood or other materials

that can be easily drilled. If you have solid surface, marble, granite, or

other very hard countertops, skip to step 13 now.

• If insulation is covering the area in 12a, fold it back.

• Orient the mounting brackets (D) for top mounting as shown in12b.

• Using pliers, bend side flanges down as shown in 12c and 12d so the

bracket will not slip out of slot in frame. Do not attach to cabinet yet.

Avoid Tip Over Hazard!

Do not use the dishwasher until it is completely installed.

When opening the door on an uninstalled dishwasher,

carefully open the door while supporting the rear of the unit.

Failure to follow this warning can result in serious injury.

WARNING

!

Note: Before installing the supplied counter top mounting brackets,

decide which method of securing the dishwasher into its enclosure will

be used.

Once the mounting brackets are installed on the dishwasher, removing

them is dicult and will damage the mounting brackets and the

dishwasher.

If you have a Fully Integrated Panel, do not attach mounting brackets until

after attaching the panel to the door.

12

18

• Side Mount is used for counter tops made of marble, granite, or other

very hard materials that cannot be easily drilled.

• Grasp mounting bracket (D) with pliers and fold bracket at the perforation

over onto itself as shown in 13a.

• Slip bracket flange through side slots in frame as shown in 13b.

• Using pliers, bend side flanges down as shown in 12c and 12d so the

bracket will not slip out of slot in frame. Do not attach to cabinet yet.

13

19

• If your sink is to the right side of where you are installing the dishwasher,

you will need to reposition the hoses and power cord behind the

dishwasher before installing.

• To do so, unhook the strap that the hoses are running through on the

back of the dishwasher base and position them per your requirements.

• If your sink is to the left side, leave the hoses and power cord as they

came and skip to step 16.

Positioning the Dishwasher

14

20

• Reposition the hoses so they run through the strap on the other side.

• Be sure to snap the strap back in place to secure the hoses as shown.

15

• To avoid scratching the floor, use floor protection and caution when

sliding the dishwasher into the cabinet. Use hands on both sides of

dishwasher to push evenly.

• Pull water inlet, drain hose and power cord through the hole in cabinet

as shown.

16

21

• Push the unit 2/3 of the way into the opening and stop.

17

• Reach into adjacent cabinet and pull hoses and excess power cord

completely out so they do not get kinked.

• Push the unit in until flush with cabinet door.

18

Page is loading ...

Bosch SHXM63W55N Installation guide

Bosch SHXM63W55N Installation guide

in other languages

Related papers

Other documents