Symbol Technologies 3100 User manual

RS 2200/3200 Series

Series 3100

Quick Reference

Symbol reserves the right to make changes to any product to improve reliability, function,

or design.

Symbol does not assume any product liability arising out of, or in connection with, the

application or use of any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise under any

patent right or patent, covering or relating to any combination, system, apparatus,

machine, material, method, or process in which Symbol products might be used. An

implied license exists only for equipment, circuits, and subsystems contained in Symbol

products.

Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc. Other

product names mentioned in this manual may be trademarks or registered trademarks of

their respective companies and are hereby acknowledged.

Symbol Technologies, Inc.

One Symbol Plaza

Holtsville, N.Y. 11742-1300

http://www.symbol.com

Patents

This product is covered by one or more of the following U.S. and foreign Patents:

U.S. Patent No. 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717;

4,760,248; 4,806,742; 4,816,660; 4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833;

5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461; 5,113,445; 5,130,520; 5,140,144; 5,142,550; 5,149,950;

5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,216,232; 5,229,591; 5,230,088; 5,235,167; 5,243,655; 5,247,162;

5,250,791; 5,250,792; 5,260,553; 5,262,627; 5,262,628; 5,266,787; 5,278,398; 5,280,162; 5,280,163; 5,280,164;

5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,321,246; 5,324,924; 5,337,361; 5,367,151; 5,373,148; 5,378,882;

5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440;

5,444,231; 5,449,891; 5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322;

5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592; 5,557,093; 5,578,810; 5,581,070; 5,589,679;

5,589,680; 5,608,202; 5,612,531; 5,619,028; 5,627,359; 5,637,852; 5,664,229; 5,668,803; 5,675,139; 5,693,929;

5,698,835; 5,705,800; 5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,742,043; 5,745,794; 5,754,587; 5,762,516;

5,763,863; 5,767,500; 5,789,728; 5,789,731; 5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520;

5,823,812; 5,828,050; 5,848,064; 5,850,078; 5,861,615; 5,874,720; 5,875,415; 5,900,617; 5,902,989; 5,907,146;

5,912,450; 5,914,478; 5,917,173; 5,920,059; 5,923,025; 5,929,420; 5,945,658; 5,945,659; 5,946,194; 5,959,285;

6,002,918; 6,021,947; 6,031,830; 6,036,098; 6,047,892; 6,050,491; 6,053,413; 6,056,200; 6,065,678; 6,067,297;

6,068,190; 6,082,621; 6,084,528; 6,088,482; 6,092,725; 6,101,483; 6,102,293; 6,104,620; 6,114,712; 6,115,678;

6,119,944; 6,123,265; 6,131,814; 6,138,180; 6,142,379; 6,172,478; 6,176,428; 6,178,426; 6,186,400; 6,188,681;

6,209,788; 6,216,951; 6,220,514; 6,243,447; 6,244,513; 6,247,647; 6,308,061; 6,250,551; 6,295,031; D305,885;

D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478; D383,124; D391,250; D405,077;

D406,581; D414,171; D414,172; D418,500; D419,548; D423,468; D424,035; D430,158; D430,159; D431,562;

D436,104.

Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875; 1,955,269 (Japan); European

Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/03938; Italy 1,138,713.

rev. 11/01

3

Introduction

The Series 3100 terminals are lightweight, battery powered,

hand-held computer systems. Data can be entered using the

terminal keyboard, the integrated laser scanner, or the tethered

bar code scanners.

The Series 3100 includes both batch and radio terminals. The

PDT 3100 performs direct communications. The PDT 3110

and 3124 perform Spectrum One radio communications. The

PDT 3140 performs Spectrum 24 radio communications. All

Series 3100 terminals can be used as remote terminals for

collecting and storing data that is later uploaded to a host

computer.

About this Guide

This guide presents information on the parts of a Series 3100

terminal and instructions for the following procedures:

• Powering the terminal on and off

• Performing communications

• Charging the batteries

• Replacing the batteries

• Connecting the modems

• Connecting the terminal to a printer

• Configuring the scanner trigger

• Attaching a tethered scanner

• Using the scanners

Quick Reference

4

Parts of the Series 3100 Terminal

ALKALINE

BATTERY

PART NO.:

3100-9M0L050

S/N: B029721

SYMBOL TECH, INC.

WARNING

REPLACE BATTERIES QUICKLY TO INSURE

CONTINUOUS OPERATION OF BACKUP

BATTERY SYSTEM.

BEFORE STORING UNIT FOR EXTENDED

PERIODS (OVER 1 MONTH) CONSULT

OPERATING MANUAL OR CALL SYMBOL

FIELD SERVICE.

PDT 3100

DECODE SCAN

1

3

2

4

5

6

7

8

14

9

11

12

15

6

9

16

13

10

5

Parts of the Series 3100 terminal include:

1. Integrated Rotatable Laser Scanner

2. Scanner Window

3. Scanner LED

4. LCD Display Screen

5.

PWR Key

6. Alpha/Scanner Triggers

7. Keyboard

8. Serial Port (RJ-41)

9. Hand Strap

10. Hand Strap Hook

11. Battery Compartment Latch

12. Battery Compartment Cover

13. Battery Compartment

14. Alkaline Battery Socket

15. Rechargeable NiCd Battery Socket

16. Battery

Quick Reference

6

Power On and Off

Note: If the terminal is powered by a NiCd battery, charge the

battery fully before using the terminal.

To turn the terminal on or off, press

PWR.

Battery Charging and Communications

To charge the PDT 3100’s batteries or perform communications,

you have the option of using either a 31XX cradle or the 3115

Communications/Charger Adapter.

3115 Communications/Charger Adapter

The Series 3100 has an optional communications/charger

adapter (CCA) that facilitates communication with a host when

no cradle is available, and provides power to the terminal from

a wall-mounted power supply for battery charging during

terminal use and flash EPROM programming.

Battery Charging

To provide power directly to a terminal for charging the

NiCd battery:

1. Plug the 10-pin RJ41 connector into the base of the Series

3100 terminal.

2. Plug the connector from the 15V power supply,

P/N 55915-00-00 (US, 115V) or 60507-00-00 (International,

230V) into the power input jack (J1) on the CCA.

7

3. Plug the power supply into a wall socket.

NiCd batteries require 12 to 16 hours to recharge fully.

The terminals may be used while the battery is being

charged.

Note: Alkaline batteries cannot be charged in the terminal.

To charge the batteries more quickly, use the cradle as

detailed in 31XX Cradles, Battery Charging.

115V

Keyboard

Mouse

COM A

COM B

Parallel

VGA

Wall

Phone

7

8

9

6

3

2

5

4

1

0

ENTER

F7

F8

F9

F6

F5

F4

F1

F2

F3

=

F10

C

LR

F

NC

SHF

CTL

PWR

LIGHT

DARK

LAMP

SPACE

A

B

C

D

E

J

O

T

Y

X

W

V

U

P

K

F

G

H

I

N

S

R

M

L

Q

BSP

Z

RJ-41 Connector

3115 CCA

DB-25 Connector

Power Input Jack

Quick Reference

8

Communications

Note: It is NOT necessary to connect the terminal to a power

source for communications.

To communicate with a PC or printer:

1. Plug the 10-pin RJ41 connector into the base of a Series

3100 terminal.

2. Plug the DB25 connector into the host’s communications

port.

To connect the CCA to a modem:

1. Plug the 10-pin RJ41 connector into the base of a Series

3100 terminal.

2. Insert a female-to-male gender changer on the female

DB25 connector before plugging the connector into the

modem.

Note: The CCA is shipped set for RS-232 communications with

a PC. To use the CCA with a modem or printer may

require changing the internal communications settings.

Refer to the installation instructions (P/N 70-11314-01).

9

31XX Cradles

The single-slot and four-slot cradles are optional devices used

for charging the batteries and performing host communication

with the terminal.

Battery Charging

To recharge the NiCd battery pack in the cradle:

1. Plug the power supply cord round plug in the power

connector on the side of the cradle.

2. Connect the power supply cord AC plug to a standard

electrical outlet.

3. Place the terminal in the cradle.

The battery pack is fully charged in approximately 90

minutes.

7

8

9

6

3

2

5

4

1

0

ENTER

F7

F8

F9

F6

F5

F4

F1

F2

F3

=

F10

CLR

FNC

SHF

CTL

PWR

LIGHT

DARK

LAMP

SPACE

A

B

C

D

E

J

O

T

Y

X

W

V

U

P

K

F

G

H

I

N

S

R

M

L

Q

BSP

Z

PDT 3100

CHARGING

COMM

Quick Reference

10

Communications

To communicate using the cradle:

1. Perform Steps 1 - 2 from the section Battery Charging.

2. Connect the cradle to the host computer using a null

modem cable

3. Insert the terminal in the cradle and perform the

communication steps as detailed in the Series 3100 System

Administration Manual (P/N 62605-00-90) or Series 3000

Application Programmer’s Guide (P/N 59045-00-92).

4. If the cradle is equipped with a modem (single-slot

cradles only), connect it directly to the telephone wall jack

and proceed as directed in the Series 3100 System

Administration Manual.

For more information on the single- and four-slot cradles,

refer to the 3165/3166 Cradle Base Modules Quick Reference

Guide (P/N 70-11313-xx).

11

Replacing the Batteries

To replace the NiCd or NiMH battery:

1. Turn the terminal off.

2. Release the hand strap, unlock the battery compartment

door and remove it.

3. Position the battery adapter in holding plug and press

into place.

4. Fit the NiCd or NiMH battery pack in compartment next

to adapter. Verify that removal strap is accessible (not

tucked under battery), before pressing battery in place.

Note: NiMH batteries cannot be charged in the terminal

through the Communications/Charger Adapter.

PART NO.:

3100-9M0L050

S/N: B029721

SYMBOL TECH, INC.

Nickel Cadmium Battery

SEALED TYPE-RECHARGEABLE

GATES

K•TEC

ELECTRONICS

HOUSTON

PART NO.:

3100-9M0L050

S/N: B029721

SYMBOL TECH, INC.

PART NO.:

3100-9M0L050

S/N: B029721

SYMBOL TECH, INC.

NiCd

Battery

Compartment

Strap

Battery

Adapter

Hand

Strap

Battery

Compartment

Door

Quick Reference

12

5. Verify that battery and adapter are properly seated.

6. Replace and lock battery compartment door.

7. Replace handstrap.

13

Connecting the Modems

Direct Connect

Some terminals use an optional internal modem that communicates at

rates of up to 14,400 bps (with v.32 bis data compression). There are

specific firmware settings which are used to configure the

modem’s hardware and software for proper operation and

regulatory compliance. The terminal’s application can control

these settings and enable you to view and amend the settings for

country/region, pulse/tone dialing, or repeat dial timing.

Incorrectly defining these settings can lead to illegal use of the

modem and can create unreliable operation. The application

developer should consult the Series 3000 Application

Programmer’s Reference Manual for correct settings.

If your terminal is equipped with a direct connect modem,

connect the modem as follows:

1. Turn the terminal off.

2. Release the hand strap on the back of the terminal.

Quick Reference

14

3. Detach the protective plug covering the modem jack on

the back of the terminal and plug in one of the telephone

cord’s connectors.

4. Plug the cord’s other connector into a telephone jack.

5. Turn the terminal back on.

RJ-41 Jack

15

Acoustic

Some Series 3100 terminals are equipped with a built-in acoustic

modem which allows direct data transmission over a telephone

line.

If your terminal is equipped with an acoustic modem, connect

the modem as follows:

1. Turn the terminal off.

2. Release the hand strap on the back of the terminal.

3. Slide the mouthpiece of the telephone into position on the

muff. Place the hand strap over the telephone handset as

shown below and reattach the strap.

4. Turn the terminal back on.

Quick Reference

16

Connecting the Terminal to a Printer

The Series 3100 has an optional cable (p/n 25-10413-01) which is

used to connect the terminal to a PS-1000 Series printer or a

tethered PS-200 printer (P/N 20-11062-03).

To connect the terminal to one of the printers listed above:

1. Plug the 10-pin RJ41 connector into the base of a Series

3100 terminal.

2. Plug the DB9 connector in the communications port on

the printer.

RJ-41

DB9

17

Using the Integrated Laser Scanner

The integrated scanner has a unique trigger that the operator

can configure. To select the trigger and use the integrated laser

scanner:

1. Power on the system and scanner by pressing

PWR or the

scanner trigger.

2. Lift and turn the scanner to the direction you wish to scan.

The scanner turns toward the back of the terminal.

3. Press the

FUNC key and the trigger you are most

comfortable using (see the figure below). This selects the

scanner trigger. The other trigger defaults to an ALPHA

shift key on the 35-key terminal.

Quick Reference

18

4. Point the scanner at the bar code and press the trigger or

press the soft trigger key (

ENTER). The thin, red laser beam

covers the entire length of the bar code.

The terminal indicates a successful scan by illuminating

the green scanner LED, beeping one or more times, and/

or displaying the decoded bar code on the screen.

19

Connecting and Using a Tethered Scanner

To attach a wand or laser scanner to the Series 3100 terminal:

1. Turn the system off.

2. Remove the plastic cap in the top of the terminal.

3. Plug the scanner into the top of the terminal as shown

below.

4. Aim the scanner at the bar code and press the trigger.

Note: Depending on your application, you may need to turn on

the terminal before using the scanners.

5. If using a wand scanner, lightly touch the scanner tip to

the white space at the left side of the bar code and move it

to the right.

Guide utilisateur

20

IEC825/EN60825 Class 1 Scanner

Series 3100 terminals are equipped with an IEC825/EN60825

scanner operate on an emissions accumulator or “gas tank”

which determines the amount of scan time that you have

available. To meet low power consumption standards, the

scanner cannot scan continuously.

If the gas tank runs out of scan time, the terminal emits a long

low beep. Release the scan trigger and wait until the terminal

emits a long high beep, indicating that it accrued enough scan

time for you to resume scanning.

Page is loading ...

Symbol Technologies 3100 User manual

This manual is also suitable for

Symbol Technologies 3100 User manual

in other languages

Related papers

Other documents